Im soo pissed off right now.
So here is the situation. I'm hoping that I can quickly find help for the battle that me and my AT&T Tilt WM 6.1 are going through.
The name of the war -
CLEARTEMP ERASED EVERYTHING!!!!
So im at work on my office phone when my Tilt (which was in my holster on my hip) started vibrating... in three buzzes. I thought it was a message so I didnt answer right away.
5 minutes later I take out my phone to see who sent me a message but for some reason instead of seeing the S2U2 screen there was a "are you sure you want to?" block asking if i wanted to erase one of my programs because it was a unistalled registry, so the first thing i did was say no...... IT DID THAT FOR ABOUT 28 TO 30 DIFFERENT PROGRAMS!!!
Afterwards I exited out of Cleartemp to see if the programs were still on my phone but to my surprise not only were all of my programs gone but my storage card was completely erased and their was no settings folder and the only thing left in the programs folder was Games, tool box, file explorer and that fu3kin Media net.
I would have simply hard reset and used my sprite backup but there was no settings folder to get to the hard reset and my storage card was wiped completely clean.
so now i cant even hard reset and start from the ground up.
What can i do?
THANKS IN ADVANCE for taking the time to scratch your head in curiosity with me.
I would appreciate anyones help in helping me get through this War!!!
"THE VILLAIN"
Do a hard reset by holding down the two softkeys and pushing the reset button on the bottom, keep the softkeys held till the unit acts like it's resetting. It's things like that that make me not use Cleartemp, Memmaid, or any of those other "registry cleaning" programs - they tend to screw things up more than help IMO. Sucks though.
Yeah, that's a real bummer, sorry to hear about that. In my opinion, cleartemp is alright, but some options in the program are very smart to avoid, like registry functions. I have tried the hard reset by keys method that many websites have suggested, however many do not work for me anyway. For my Tilt, I have to hold the two soft keys on the front with "-" on them, press the stylus in the reset hole, hold it in for a few secs, pull it out, and then without releasing the two soft keys, press the power button and follow the on screen instructions. I hope that helps you, and good luck,
Dave
Also try one of the many file recovery tools out there to recover your erased data on your sd card.
most data when erased isnt actually gone untill new data is written on top of it. dodm writes binary to every sector of a drive and then wipes it clean in between 7 times and even then its possible to retrieve data with a lab.
thats why they say to destroy all drives physically if it contains confidential data. Ive used different freeware and trial ware apps in the past to recover lost data from curropted or accidentally formatted drives and have recovered some if not all my data. just make sure you only imediately remove that sd card (keep the os from writting junk to it)and only insert it into a card reader when your ready to try to recover it.
I googled sdhc file recovery
http://www.google.com/search?hl=en&q=restore+sdhc+recovery&aq=f&oq=
lots of things came back unfortanetly I cant remeber the name of the app I last used but a little reading and hopefully you can recover your sprite settings.
I hate to play devil's advocate here, but this post sounds surprisingly like what would happen if someone had their phone stolen and was using a security program to delete all information in such a case. A text message, then no programs, no data, nothing...
I'm not saying that this is definitely the case, but it is something to consider. That being said.... if you haven't messed with your SD, you can try some sort of recovery software on a PC to get your information back. It will copy block for block info from your SD to anohter location. As long as you haven't tried rewriting over your SD, you may have a good chance of recovering your backup.
THANK YOU!!
Thanks to everyone for the response and patience in helping me get through this situation. What I actually did was go to file explorer, searched for the hard-reset cab. and pressed on the "ink."
That did a hard-reset and luckily every time I save a program to my phone I make a copy and save it to a flash drive. So basically I'm in the process of re-customizing my phone to the way it was before..... (hopefully, lol)
But once again Thank you to every one for there support.
"THE VILLAIN''
Hi guys,
Well, I've searched the forum and get close...but no cigar. So, I'll go ahead and ask.
I have an AT&T Tilt, Flashed the 6.1 from XDA MONTHS ago, and have been running Slither's Cube...not even all the time...as well as the HTC Home Customizer.
Yep, that's it.
Well, I have purchased another Tilt with a busted screen (otherwise absolutely fine) for $30 and am waiting to afford a new screen for it...at which time I'll have a backup and then the Cooking and Flashing will begin in earnest!
But I digress. Here is the sequence of events, and where I am at now:
1) Went to hang up from a phone call (BT headset active) by pressing the "Hang Up" Button...no response from the phone.
2) Pressed the Power Button...no response.
3) Slid open the Keyboard...no response.
4) Held the Power Button...no response.
5) Dumped the battery and rebooted...AT&T Splash then Radio Info...stays right there. Screen will dim after awhile, but never goes out. Rebrightens when removing external Power.
6) Soft Reset...same result.
7) Only way to Power Down is dump the battery.
8) Removed SD and SIM...attempted Bootloader Screen
9) Bootloader DOES show up:
KAIS1*0
SPL-1.93.0000
CPLD-8
Serial
10) I don't remember if there was anything with "Serial"...like a number or such...when I looked at it last (when flashing 6.1) so that may or may not be significant. There's nothing there now.
11) My Radios show up as:
R 1.27.14.09
G 22.45.88.07H
D 1.62.00.00
I am avoiding Hard Reset or Re-Flash until I can at least figure out what happened...if anyone has any ideas...or find out that this is common and that's the best or only way to solve it etc.
Since I haven't found anything quite like this in the Forum, I'm presuming that it may not be so common and I may...or may NOT...be able to find a way back before going that path. As well, I really don't want to send it off for repair...although I have insurance and coverage through Hawk (our AT&T Provider) that would be reasonable for repair ($35) but perhaps inordinate for rreplacement ($175). I'd like to be able to resolve this myself, but not knowing what may be wrong leaves me only with Hard Reset and/or Re-Flash alternatives...if those will even work...so out goes the question:
Has anybody run into this or have any idea of why it happened or the BEST recourse to resolve it?
Thanks in advance for any and all info, y'all are awesome and I truly appreciate your help...
RAF
These phones freeze all the time. Software conflicts, too much running at once, and it just feels like screwing you when you need it most. And of course all of a sudden, the hardware just crashes and never works again.
It looks like a hard reset will solve your problems, unfortunately, unless you do regular backups, you will lose all your info.
Thanks denco7!
Well, this is the first time it has locked up that early in the boot...all others have been easily resolved.
Hard Reset is not an issue with Data...I do keep my phone (data) backed up and have most of my volatiles on the SD.
And, honestly, I don't mind having to reflash or reinstall my apps...at least not yet, once I start cooking my own I feel I'll get a bit testy when I have to 'start over'.
I should probably find a good full backup app to snapshot the whole phone, then just put it back on when things 'happen'.
I do have a full backup from December using the 'supplied' app, so it will at least have most of the tweaks in it.
I'm gonna do the Hard Reset and see if that clears this, but I must say I'm not that hopeful.
Not really an expert...not a noob either...but this technology is just not rocket science, and I can actually do that along with quite a bit more.
Don't ask me to write a driver tho...I respect anyone that has that kind of patience!
Suffice to say, this just doesn't "feel" like a resetable issue...but I'm game. I'll update once attempted.
Thanks again, see you on the other side...
RAF
Okay...no joy on the Hard Reset. Behavior has stayed the same. Kinda expected that tho...
Next stop, Re-flash the ROM. I'm gonna check on latest releases of 'Official' HTC ROMs...but if anyone has any suggestions I'm open.
I'm still hoping that someone out there knows what happened here, it would be helpful to know the 'why'.
Thanks again...
not so much a suggestion but a correction. You don't have a wm6.1 rom but actually have a wm6 rom because the radio you have flashed i.e. R 1.27.14.09
is a wm6 radio not wm6.1 and that radio is only compatible with the following roms:
AT&T 1.60.502.3
AT&T 1.61.502.2
AT&T 1.62.502.0
Q-Mobile 1.2 AT&T Version
(source for above info: http://forum.xda-developers.com/showthread.php?t=393182)
so make sure that your rom matches the radio you have. I would recommend that if flashing is not something new to you than go ahead and upgrade your rom and radio to wm6.1 rom and see if the issue presists.
hope this helps
first post you stated you have a 6.1 rom but your spl is for a 6.0 rom, either your not on a 6.1 rom or your on the wrong SPL and should HARDspl if your flashing custom roms.
Thanks Guys...
I had it in my head that I went to 6.1 when I flashed it last...went out and looked at the file and sure enough it was 6.0.
This is what happens when u have 7 kids, 6 female and 4 of those in college...I'm too broke to pay attention.
No not new to flashing, and when I can get home before 10-11p some night...or this weekend...that's my plan.
Looking for the best choice 6.1 to flash and attempt to bring it back, but still curious as to the behavior in the first place.
Thanks for pointing out my ADD, and all comments are welcome...
Hoping for the un-bricking soon...
RAF
Now I'm REALLY Currious...and Frustrated! A Little Help Please...
Okay,
So I flashed the latest HTC Factory ROM: AT&T Tilt Windows Mobile 6.1 Software (ROM Version 3.57.502.2 WWE).
I wanted to do something mild at first before taking too many big steps...'small steps Ellie, smal steps'.
Once the Bootloader was up with USB showing at the bottom, I was certain I would at least have a connection to the Phone.
Of course with no ActiveSync or recognition from the PC, I simply ran the EXE and ignored the one line about making sure ActiveSync had a connection.
The only oddity was that at 13%, the Phone went from the "% Screen" back to the Bootloader Screen for a few seconds then continued normally to sucessful completion.
When it rebooted, it stayed at the AT&T initial splash and now NEVER shows the Radio or Protocol versions...just the initial splash.
As well, it does not dim the backlight after awhile as it used to nor do I ever get a Power Light...just plain LOCKED.
There is also still no way to Power Down the Phone except for removing the Battery.
Although I've never used MTTY, I'm wondering if that is now my only hope...and am currious as to the proper procedure for this particular circumstance.
I'm still searching the Forum for MTTY uses and info, but I would be appreciative if one of the Seniors could point me in the right direction.
Also, if ANYONE knows what may have caused this glitch in the first place it would help me to determine the best recourse.
Thanks again in advance to all...
RAF
Rustafergi said:
Okay,
So I flashed the latest HTC Factory ROM: AT&T Tilt Windows Mobile 6.1 Software (ROM Version 3.57.502.2 WWE).
I wanted to do something mild at first before taking too many big steps...'small steps Ellie, smal steps'.
Once the Bootloader was up with USB showing at the bottom, I was certain I would at least have a connection to the Phone.
Of course with no ActiveSync or recognition from the PC, I simply ran the EXE and ignored the one line about making sure ActiveSync had a connection.
The only oddity was that at 13%, the Phone went from the "% Screen" back to the Bootloader Screen for a few seconds then continued normally to sucessful completion.
When it rebooted, it stayed at the AT&T initial splash and now NEVER shows the Radio or Protocol versions...just the initial splash.
As well, it does not dim the backlight after awhile as it used to nor do I ever get a Power Light...just plain LOCKED.
There is also still no way to Power Down the Phone except for removing the Battery.
Although I've never used MTTY, I'm wondering if that is now my only hope...and am currious as to the proper procedure for this particular circumstance.
I'm still searching the Forum for MTTY uses and info, but I would be appreciative if one of the Seniors could point me in the right direction.
Also, if ANYONE knows what may have caused this glitch in the first place it would help me to determine the best recourse.
Thanks again in advance to all...
RAF
Click to expand...
Click to collapse
If you cannot flash a 6.1 rom or install the correct hard spl I would not even attempt using MTTY. Go to the rom section of this forum. Look for "spl rollup thread" it is a sticky from DaveShaw. Pick any 3.xx hard spl's for 6.1 rom and download. Now download jumpspl and place it somewhere on your device other than your memory card. Now run jumpspl and follow the rest of the directions in that thread. After you installed the correct SPL find a 6.1 rom and flash your device. If your sound doesn't work change your radio to a compatible radio, which would be listed in the "ultimate radio thread" by alltheway.
These are the basics. Hope it helps.
Rustafergi said:
Okay,
So I flashed the latest HTC Factory ROM: AT&T Tilt Windows Mobile 6.1 Software (ROM Version 3.57.502.2 WWE).
I wanted to do something mild at first before taking too many big steps...'small steps Ellie, smal steps'.
Once the Bootloader was up with USB showing at the bottom, I was certain I would at least have a connection to the Phone.
Of course with no ActiveSync or recognition from the PC, I simply ran the EXE and ignored the one line about making sure ActiveSync had a connection.
The only oddity was that at 13%, the Phone went from the "% Screen" back to the Bootloader Screen for a few seconds then continued normally to sucessful completion.
When it rebooted, it stayed at the AT&T initial splash and now NEVER shows the Radio or Protocol versions...just the initial splash.
As well, it does not dim the backlight after awhile as it used to nor do I ever get a Power Light...just plain LOCKED.
There is also still no way to Power Down the Phone except for removing the Battery.
Although I've never used MTTY, I'm wondering if that is now my only hope...and am currious as to the proper procedure for this particular circumstance.
I'm still searching the Forum for MTTY uses and info, but I would be appreciative if one of the Seniors could point me in the right direction.
Also, if ANYONE knows what may have caused this glitch in the first place it would help me to determine the best recourse.
Thanks again in advance to all...
RAF
Click to expand...
Click to collapse
Wow! I think you missed the advice and wisdom given to you about NOT FLASHING a 6.1 ROM with the SPL for a 6.0 ROM...
Anyways, lets see if we can help... I don't think you are going to be able to flash a SPL, as you probably can't even get an active sync connection to copy over the files...
So, try getting into boot loader screen; you hold down the camera button and then press in the rest button and hold that until a tri-color screen appears...
Then tell us exactly what it says, just to make sure we know which SPL you have... Then I will post a link to the exact ROM you need to flash to hopefully bring her back to life.
If you are not able to get into boot loader, which wouldn't surprise me, someone else with more experience un-bricking will have to help.
Some Answers and Info...Still Confused
redbandana said:
If you cannot flash a 6.1 rom or install the correct hard spl I would not even attempt using MTTY. Go to the rom section of this forum. Look for "spl rollup thread" it is a sticky from DaveShaw. Pick any 3.xx hard spl's for 6.1 rom and download. Now download jumpspl and place it somewhere on your device other than your memory card. Now run jumpspl and follow the rest of the directions in that thread. After you installed the correct SPL find a 6.1 rom and flash your device. If your sound doesn't work change your radio to a compatible radio, which would be listed in the "ultimate radio thread" by alltheway.
These are the basics. Hope it helps.
Click to expand...
Click to collapse
pjcforpres said:
Wow! I think you missed the advice and wisdom given to you about NOT FLASHING a 6.1 ROM with the SPL for a 6.0 ROM...
Anyways, lets see if we can help... I don't think you are going to be able to flash a SPL, as you probably can't even get an active sync connection to copy over the files...
So, try getting into boot loader screen; you hold down the camera button and then press in the rest button and hold that until a tri-color screen appears...
Then tell us exactly what it says, just to make sure we know which SPL you have... Then I will post a link to the exact ROM you need to flash to hopefully bring her back to life.
If you are not able to get into boot loader, which wouldn't surprise me, someone else with more experience un-bricking will have to help.
Click to expand...
Click to collapse
Hi again,
Thanks to redbandana and pjcforpres for the responses...I thought I might not get anymore!
I'll start with pjcforpres,
First, my appologies if I have not been specific enough on my descriptions...I've been attempting to be more succinct (I'm not so good at that).
This was a Stock ROM Tilt, then I had flashed RUU_Kaiser_CINGULAR_WWE_1.62.502.0_radio_sign_22.45.88.07_1.27.14.09R2_Ship.exe quite awhile back...shortly after it was available.
I added Slither's Cube and the HTC Home Screen and Customizer and have run it that way since then.
Somehow, I got it in my head that I had flashed 6.1 but I was flat out mistaken...hence the comment in the earlier part of the thread.
Then we get to the #1 post in this thread...add some confusion and voila.
The ref'd 6.1 flash was also Stock...RUU_Kaiser_CINGULAR_WWE_3.57.502.2_radio_sign_25.88.40.05_1.65.21.18_Ship.exe...and I thought I read everything, incl that it replaces the SPL.
Durring the flash, it pauses @ 13%, the USB disconnect 'bing' sounds and the Bootloader screen reappears showing SPL-3.02.000.
Then, the USB reconnect 'bing' sounds, goes back to the % screen and then completes the flash successfully.
My Bootloader screen is now:
KAIS1*0
SPL-3.56.000
CPLD-8
So...did I miss something and screw up? Or was I on the right track?
And redbandana,
It did successfully flash 6.1, but it still doesn't start...specifically, get passed the initial AT&T Splash.
Although I had already thought of going to JockyW's HardSPL 3.29, I cannot 'see' the phone in XP and therefore cannot get JumpSPL onto it...so, no HardSPL (unless I missed something else in the threads).
It DOES however give me the USB 'bing' sound when I go into the Bootloader...but clicking on the "Mobile Device" icon in Windows Exploder leaves a 'blank' right pane.
Before your post, I had read up on MTTY and noted the DON'Ts...like DON'T use task 2a!...and found several threads with commands.
None of the info commands seem to fuction, like info 2, info 7 or info 8 so I don't have much 'info' there.
One of the things I tried was 'task 28' to format the thing in case there was some corruption...this was the response:
Cmd>task 28
Format start
Storage start sector=0xC2C0, total sector=0xF000
Storage start block=800, total block=960
Total Bad Block in CE: 1
Erase physical block from 1091 to 2032
formatstorage Bad block found: 1397
formatstorage Bad block found: 1398
si backup: Erase physical block from 2032 to 2048
Format end
So I looked for 'bad blocks' on the Forum and there are suggestions to contact JockyW and GSLEON3 for more help.
I haven't as yet done this thinking I can work my way through this by searching the Forum and monitoring this Post.
My searches for MTTY Commands have shown me that there are different Commands for different SPLs, and the info is way scattered and confusing.
It is becoming clear(er) to me that I have an issue that is not that normal...or at least not with an intermediate level 'fix'.
That's why I asked for more help in the right direction, I feel like I've hit this pretty hard and done alot of footwork on my own.
I also feel like I'm running out of options and may resort to bugging JockyW and GSLEON3...unless there are any more suggestions
PLEASE let me know if there is more info that I can provide to narrow this down, or some procedure to attemt, or an MTTY comand that will give us more info, or another search in the Forum for something specific I've missed...or simply some PFM that can be performed...and I'll be HAPPY to comply!
Thanks again...and again...for the assistance, my grattitude and appreciation out!
RAF
I am going to be short and swet for the moment... my computer crashed so I am solely on my phone until I work again around 2 central time USA...
Good news is that there is a chance without MTTY to get you running, and if not, those with the knowledge are very hepful and patient.
I will do the searches tomorrow for the stock ROM you should try, and give a walk through on how to flash using a micro SD card.
I am out for now, and will get back to you as soon as I can tomorrow.
Patient and Prepared
Thanks pjc...if we can fix this I'll vote for you
I sincerely appreciate the assistace, and PLEASE let me know if there's any research I can do to facilitate.
If you're willing, let me know if I took a wrong turn somewhere or if I did something to make this worse...I like to learn from my mistakes (I AM pretty good at those...)
I just got the new screen for my backup Tilt and I'll be swapping that out tomorrow (uh...today) sometime, so I'll have a reference phone soon.
Askew but relevant, I'm on day 12 of a nasty cranial muscle spasm and 3 days into meds for it...so we'll see if I can stay focused
Thanks again and in advance...
RAF...Tilted
http://www.htc.com/us/SupportDownload.aspx?p_id=67&cat=2&dl_id=94
Try downloading from here... it is the 100% official AT&T Tilt 6.1 ROM, plus upgrade tool.
This includes everything you need, and is probably what you flashed already, but it sounds like you had a bad flash or something...
Make sure your computer doesn't go into hibernate during this process, and that you don't have anything running other than the update program and activesync...
Also, make sure when you run the update program, you right click and select 'run as administrator' or 'run as' then in the menu that comes after that select administrator.
If you can't establish an activesync connection, or if you are using Vista, and thus no Windows Mobile Device Center connection can be established, let me know, and I will track down the ROM by itself and the Radio by itself and walk you through that.
This should be the easiest fix, though, so we will try this first.
Been There, Done That...I Think ?!?
pjcforpres said:
http://www.htc.com/us/SupportDownload.aspx?p_id=67&cat=2&dl_id=94
1] Try downloading from here... it is the 100% official AT&T Tilt 6.1 ROM, plus upgrade tool.
2] This includes everything you need, and is probably what you flashed already, but it sounds like you had a bad flash or something...
Make sure your computer doesn't go into hibernate during this process, and that you don't have anything running other than the update program and activesync...
3] Also, make sure when you run the update program, you right click and select 'run as administrator' or 'run as' then in the menu that comes after that select administrator.
If you can't establish an activesync connection, or if you are using Vista, and thus no Windows Mobile Device Center connection can be established, let me know, and I will track down the ROM by itself and the Radio by itself and walk you through that.
This should be the easiest fix, though, so we will try this first.
Click to expand...
Click to collapse
1] Yep, same one I have already flashed several times to determine if there was a pattern.
2] ActiveSync will not connect...remember from #1 in this post:
1) Went to hang up from a phone call (BT headset active) by pressing the "Hang Up" Button...no response from the phone.
2) Pressed the Power Button...no response.
3) Slid open the Keyboard...no response.
4) Held the Power Button...no response.
5) Dumped the battery and rebooted...AT&T Splash then Radio Info...stays right there. Screen will dim after awhile, but never goes out. Rebrightens when removing external Power.
6) Soft Reset...same result.
7) Only way to Power Down is dump the battery.
8) Removed SD and SIM...attempted Bootloader Screen
9) Bootloader DOES show up:
KAIS1*0
SPL-1.93.0000
CPLD-8
I've never gotten passed the initial AT&T Splash since then...no matter soft hard reset flash the 6.0 ROM that was already on it or this 6.1 version.
Only difference is when I flashed this 6.1 ROM, the Radio and Protocol Versions that normally pop up at the bottom in red no longer pop up.
It now stays at the initial AT&T Splash, no versions, and never dims the backlight.
The ONLY time my Laptop 'sees' the Phone is when I put in into the Bootloader I get the USB 'bu-bingk'.
MTTY can see it, and the ROM Upgrades see it and run successfully...but Exploder can't and neither does ActiveSync.
Just to clarify that I've been there more than once...
3] Well, that I have not attempted...but all my previous flashes have gone fine (I am the only user on my Alenware Aurora m7700...and effectively I AM the Administrator), so I'll attempt that...(see next).
I downloaded, overwrote and ran this 6.1 ROM again...I set this XP install with me as the only Administrator (only user other than Guest), and I want to point something out that may be significant:
The Screnshots below show that there's no info in the Current Image Version area, I click on 'Update' and get the 2nd one.
(okay, sorry I haven't attempted very hard to embrace multiquote or embed a screenshot yet )
But this has happened every attemp to reflash after the initial sequence of events. As well, the same events recurred during the flash as all attempts before:
Durring the flash, it pauses @ 13%, the USB disconnect 'bing' sounds and the Bootloader screen reappears showing SPL-3.02.000.
Then, the USB reconnect 'bing' sounds, goes back to the % screen and then completes the flash successfully.
So...did I screw up somewhere? I really thought I had a handle on the 'small steps' that I took..it was the 'next steps' that I was mildly trepidatious about.
My understanding and instincts point to the 'bad blocks' errors durring the MTTY 'task 28' format, but I can't find anything pertinent to 'do' about it in the Forums...other than contacting JockyW or GSLEON3.
I want to try SOMETHING on my own before I go bothering them with a PM...although I've read (and even learned) alot here recently on TOP of what I had already learned over the last 2½ years, I feel I've got to at least attempt something before begging for help that way.
Still, I haven't found a path to get this basal into the core of the phone to noodle (safely mind you) around and become more adept so that I can solve these issues on my own...and it may be time to capitulate.
Let me know if you've spotted an error on my part...something I did or didn't do...or if there's another path I should take or search in the Forum I should look up.
Thanks ton again...and my appologies to all for my un-succinct pontifications...
(S)tilted...RAF
I don't think you are really doing anything wrong on your part, it just doesn't want to flash right... I had you try the stock stuff again just to make sure it was a clean download, and a clean flash.
I am not sure if it is the SPL not matching the ROM, or the Radio... The MTTY commands do indicate a problem with something not flashing right to the phone. Especially since that download has been recommended and successful so many times for people with a similar situation. I have done a fair amount of looking into this myself, and I have found a couple solutions:
1. Some people found success by flashing the same stock AT&T ROM 2 -5 times, and then it finally caught and worked right.
2. Others found luck by flashing a HardSPL, then new Radio, then new ROM.
3. They PM one of the greats... right now in the Kaiser area, JockyW is amazing! But is mostly focused on newer devices. I would recommend contacting mskip or DaveShaw. They have much more experience than I do, and should have a better idea of exactly what those block errors mean, and the solution....
If I were you I would try one last time doing a hard rest, you may need to hold down the 2 soft keys and the rest button extra long to get it to register... I would also try flashing that same upgrade 1 last time, followed by 1 last shot at a hard rest. If you still have the same stuff going on, I would contact those 2 guys and see what their wisdom says... mskip moderates the "NOOB flashing guide" thread and DaveShaw is a moderator for the Kaiser section in general.
Thanks pjcforpres...Contacting DaveShaw...Any Other Ideas?
Okay, one more time...and, no joy. Held the Soft Keys for 2 mintes solid for the Hard Reset, Reflashed, then another 2min Hard Reset.
I've resorted to sending DaveShaw a PM per the suggestion and will patiently wait for a reply.
In the mean time, if there's ANY other suggestions or a list of MTTY commands that run on the 3.56.000 SPL that can get info from the phone to help determine what the actual problem is or to correct bad blocks I'd be SERIOUSLY appreciative and VERY grateful.
Thanks to all who have responded, and in advance to all who may help from here...
RAF
A Little Updated Info:
Replaced the screen on my 'backup' Tilt, and flashed the RUU_Kaiser_CINGULAR_WWE_3.57.502.2_radio_s ign_25.88.40.05_1.65.21.18_Ship.exe ROM thaT I had flashed on the 'bricked' one.
It had the same behavior @ 13%, so I'm certain now that the flash went fine...I am even more convinced, with all of the events and symptoms to this point, that the issue lies in the 'bad blocks' reported durring the MTTY task 28 format.
I've left a PM for DaveShaw...and I AM patient...but if there is someone that may be more appropriate for this question I'd like to contact them as well. If anyone knows the right Guru, please let me know.
Thanks again to all...
RAF
Well I'm here at last sorry for the delay in getting back to you - I'm not sure how much I can help you though .
Can you post the output of "info 2" and "info 8" from an MTTY connection to your bootloader.
Also, can you please clarify: are you stuck at the bootloader (red/green/blue) or the splash screen (with R G D)?
Thanks
Dave
DaveShaw said:
Well I'm here at last sorry for the delay in getting back to you - I'm not sure how much I can help you though .
Can you post the output of "info 2" and "info 8" from an MTTY connection to your bootloader.
Also, can you please clarify: are you stuck at the bootloader (red/green/blue) or the splash screen (with R G D)?
Thanks
Dave
Click to expand...
Click to collapse
Wow man, THANKS for just bein here!
That's just it Dave, none of the info commands in MTTY seem to return anything (see #10). I've used MTTY: ver. 0.01 2001 and ver. 1.42 1997-2001 and both report literally nothing for info 2 info 7 or info 8...just another Cmd> prompt. However, (also in #10) I get to the 'bad blocks' ref running "task 28":
Cmd>task 28
Format start
Storage start sector=0xC2C0, total sector=0xF000
Storage start block=800, total block=960
Total Bad Block in CE: 1
Erase physical block from 1091 to 2032
formatstorage Bad block found: 1397
formatstorage Bad block found: 1398
si backup: Erase physical block from 2032 to 2048
Format end
Remember, the stuff in #1 of the thread happens and then I went through all this digging...took it to where I could and posted.
This wasn't a HardSPL fail or a bad Flash... I had BEEN running stock HTC 6.0 WWE with Slither's Cube, the HTC Home Screen and Home Customizer.
RUU_Kaiser_CINGULAR_WWE_1.62.502.0_radio_sign_22.45.88.07_1.27.14.09R2_Ship.exe (flashed 07/20/08)
This isn't a RUUNBH issue either, and I can get into Bootloader and I'm not 'stuck' there...currently:
KAIS1*0
SPL-3.56.000
CPLD-8
I can flash stock ROMs all day long w/no errors...flashed HTC 6.1 WWE on my backup Tilt to be sure the behaviors were the same, and they are exactly.
RUU_Kaiser_CINGULAR_WWE_3.57.502.2_radio_sign_25.88.40.05_1.65.21.18_Ship.exe runs FINE on the backup Tilt.
After flashing the HTC 6.1 WWE on the 'bricked' one however, there is no longer the R G D Radio Protocol info at the bottom of the AT&T Splash after the initial Splash...it was there before the 6.1 flash, and that's where it used to hang: Initial Splash, R G D, hang...backlight eventually dimed but never went out...battery dump only way off.
Now it hangs at the Initial Splash, NO R G D, NO backlight dim...still needs battery dump for off. It ACTS like it's lost it's damn mind...
I'm pretty sure I 'downgraded' back to the 6.0 mentioned above and went thru some similar steps to confirm, but I didn't write it all down and I'm way ADD so I can do that one again and record it all this time...unless that's a bad idea.
I very recently (like as I was searching I saw you had answered my plea...) found some other references to a MFG HardSPL that someone was thinking about working on to fix bad blocks, but I haven't read through it all yet. And, since Exploder and ActiveSync simply can't 'see' the phone, I'm not sure that I could get a HardSPL on the thing in the first place...'cause I can't get no JumpSPL on the phone itself...should've done that back when it was working I guess
I truly believe I'm at the 'needing guru help' level at this point, but if you see something I should do PLEASE point me that way and I'll dive right in. Also, like I've asked others, if you see something I did wrong or in the wrong order or whatever, please let me know that also...there's GOT to be something I can actually LEARN from this.
I warned you I tend to pontificate, but I hope that this clears up where I'm at. ANY help you can provide is fantastic and greatly appreciated, even if it's just to tell me to go somewhere else (I'm kinda used to that )
Thanks again, seriously...
RAF
In that case I have no idea. I think GSLEON3, jockyw2001 or cmonex are going to be the only one's who can help you.
Dave
I've two problems which lead into one big problem.
First im stuck in the bootloader mode. Every time I start the Qtek 9090 it's in bootloader mode (btw it says v2.06 on the bottom). When the reset button is pressed the normal WM 2003SE should start, but there's always the bootloader. I've tried reset, hard reset and camera+power+reset. This problem exists since I used EnterBL.exe, when I used camera+power+reset, I were always be able to get back in the normal mode. I read suggestions how to solve this problem, but they contain ActiveSync. This leads us to the second problem.
I'm not be able to establish a ActiveSync (V4.5) connection when the BA is in bootloader mode. It worked perfect in Windows 2003SE. In bootloader mode the BA says "USB" on the display and XP shows the device in the device manager (I hope that's the English name, it's just a translation from the German name), but ActiveSync doesn't find a device.
I've shriked extrom to 128 KB, because I wanted to upgrade to Win 6. Maybe that's necessery infomation.
I hope someone has the answer for my little problem, because my mobile phone is currently just a expensive paper weight.
welcome to the forum!
no, it's not an "expensive" paperweight.
let me please first say, stop messing around in the device manager (yes, that is the correct name), everything is just fine, it is normal that it does not connect as usual!!!
you are exactly where you should be, and apparently you already read about how to basicly get to wm6. ok, let me explain...
since you already your extrom space, you are ready for upgrading, and that is what the bootloader is for. of course you don't start the bootloader and try and reset again, the bootloader is for opening ports to access the rom, which, otherwise would be rom=READ only memory.
another thing is, the "serial" changes to "usb" when cradled. that is no problem, that's perfect.
you are now at the point where you take the rom (nk.nbf file) and put it in a folder containing the RUU (rom upgrade utility, basicly a bunch of files named maupgradeut_noid, enterbl, getdevicedata and so on, you know where to find those apparently )
and start the maupgradeut_noid, then the rom flashing begins. after it is done, you simply perform a hard reset, but not the old fashioned way (power+reset). wm5 and above use another hard reset.
you have to press power+reset and then quickly press camera+record to access a boot menu, then you use the camera and record button to switch the options in that menu to say the following:
clear registry hive: YES
format storage: YES
enable kitl: NO
then you confirm that by pressing the mail button, your screen turns white and after a short time you are done, and wm6 will start for the first time!
have fun!
with best regards
Chef_Tony
Thanks for your effort, now it seams that think are not so bad as I thought.
I did all the steps, but I was uncertain wheater maupgradeut_noid worked right, because the program didn't show the versions of the mobile phone's software. So I thought it wasn't correctly detectet.
So it's normal that these informations are not shown by the program?
After these incidents I'm a litte bit afraid bricking my beloved BA.
that depends, my upgrade utility never showed any information on the "from" side, just the version of the rom i was going to flash, and it is fine, for some people it seems to show all the information after killing active sync first by opening the pc's taskmanager, and kill the wcesmgr and wcescommmgr processes, i can't confirm the file names though, as i have wmdc because of windows 7, but you should be able to find the active sync related processes yourself. maybe after killing them, you have all the information there.
if there is no information at all, then something went wrong and you should start playing around until you find something there again. but even if flashing wasn't successful, you would realize that, because it would be awfully fast, and nothing would have changed to your device, or it would be formatted, but nothing bad like "bricking" would happen there, you can always re-flash the device, and if you actually got stuck in bootloader, which is totally different from your situation now, you would still have ways to get the device back to life, but that is very unlikely and you are right to ask first, but you are fine so far.
You made my day!
It worked just as you said. Now I've a proper running WM 6.
Thanks to Chef_Tony and the other people putting their effort in the community.