Database Develop

Sd card flashing method don't work

hi all , i've tried to flash my trinity (s300) by wmdc under vista 64 but don't work ,also with trinity guides instructions ,( error 260)
So i have tried with Active sync under XP proS2 but don't work too ,same error
And then i have tried Sd card method described on wiki ,but when i put the phone into bootloader it doesn't read TRINIMG.nbh
So i need your help , why i can't upgrade ?
is SDHC card causing this problem ?
Before i was enable to upgrade my phone ,my actual rom is Shap's
Help me please

please close this thread ,
Solution found ,thanks

1. Extract the .NBH file from your prefered ROM upgrade: In windows use winrar (right click) to extract the contents of the exe file. In Linux / MacOS use cabextract.
2. Rename the .NBH file to TRINIMG.nbh and copy it to the root folder of your miniSD card.
3. With miniSD card inserted on the phone, start the bootloader (hold Power button on right side and Camera button at same time and stick with stylus in RESET on bottom).
4. You should see the screen pictured on the left, confirm flashing on screen by pressing the power button.
5. Flashing might hang after some time but this is normal. Just wait. Complete flash takes about 30 minutes, so check your battery or connect to charger before the flashing process starts.
6. When flashing completes soft-reset your device.
If not work
copy all file too SD
Run enterbootload
work 100%
First Unlock your CID

doesn't work
khalid1210 said:
1. Extract the .NBH file from your prefered ROM upgrade: In windows use winrar (right click) to extract the contents of the exe file. In Linux / MacOS use cabextract.
2. Rename the .NBH file to TRINIMG.nbh and copy it to the root folder of your miniSD card.
3. With miniSD card inserted on the phone, start the bootloader (hold Power button on right side and Camera button at same time and stick with stylus in RESET on bottom).
4. You should see the screen pictured on the left, confirm flashing on screen by pressing the power button.
5. Flashing might hang after some time but this is normal. Just wait. Complete flash takes about 30 minutes, so check your battery or connect to charger before the flashing process starts.
6. When flashing completes soft-reset your device.
If not work
copy all file too SD
Run enterbootload
work 100%
First Unlock your CID
Click to expand...
Click to collapse
Got same problem. Still doesn't work after copying all files.

orenroot said:
Got same problem. Still doesn't work after copying all files.
Click to expand...
Click to collapse
wich card ar you using? I know only non sdhc card do the trick and formatted ....fat or fat 16.. do some search goooooooooooooooogle..

[email protected] said:
wich card ar you using? I know only non sdhc card do the trick and formatted ....fat or fat 16.. do some search goooooooooooooooogle..
Click to expand...
Click to collapse
Non SDHC. Formatted to FAT32 as a post in the forums said. I've tried Sandisk and transcend since someone mentioned transcend has issues.
It can read the card from the OS, but it doesn't leave the bootloader.

*** Flash X1 without PC - Micro SD Method ***

This is useful if you load a bad image and cannot make an activesync connection for RUU flashing method.
This method works for any 6.1 and 6.5, and even radio rom.
*** Some Kingston brand may have problem to use SD method, no solution other than use RUU method ***
0. Make sure x1 is hard-spl first
1. Make sure yr micro-sd is formatted w/ fat-32
2. rename the image file (normally "ruu_signed.nbh") to Kovsimg.nbh, copy that to the micro-sd, and put that it yr X1
3. Make sure X1 is disconnect to your PC to avoid goes to serial mode (AC power source is OK)
4. Bring x1 to boot-loader mode by turning off the x1 completely. Hold the "volume down" button on the right, and hold the power on button until you see the tri-color screen.
5. Then follow the on-screen instruction

Thx, always using this system.

Sticky
Sticked this one!
Edit By Badwolve1: Unstickyed due to lack of posting, but reference in the X1 Thread (Here)

I am newbie in Windows Mobile system.
Please somebody tell me, what is SPL, and hard spL?

inuka said:
I am newbie in Windows Mobile system.
Please somebody tell me, what is SPL, and hard spL?
Click to expand...
Click to collapse
http://wiki.xda-developers.com/index.php?pagename=SPL Questions?
http://wiki.xda-developers.com/index.php?pagename=HardSPL

I used this method on my X1 but it keep saying " no image files " then go to serial , any solutions? thx

hysf said:
I used this method on my X1 but it keep saying " no image files " then go to serial , any solutions? thx
Click to expand...
Click to collapse
I've got the same proplem. Any suggestion?
Thanks!

I've got it working now, just d/l all the files here and follow the instructions
http://forum.xda-developers.com/showthread.php?p=2906948
Cheers!

jackleung said:
This is useful if you load a bad image and cannot make an activesync connection for RUU flashing method.
0. Make sure x1 is hard-spl first
1. Make sure yr micro-sd is formatted w/ fat-32
2. rename the image file (normally "ruu_signed.nbh") to Kovsimg.nbh, copy that to the micro-sd, and put that it yr X1
3. Bring x1 to boot-loader mode by turning off the x1 completely. Hold the "volume down" button on the right, and hold the power on button until you see the tri-color screen.
4. Then follow the on-screen instruction
Click to expand...
Click to collapse
How do you format the micro-sd, can we use the card slot provided in laptops, becoause no adapter comes with the set

songao said:
I've got the same proplem. Any suggestion?
Thanks!
Click to expand...
Click to collapse
This could be a problem with you're ROM language.
My xperia was english, so had no problem. 2 Dutch xperia's had this problem.
Just flashed SPL first, then flashed the english rom. And now the sd card method works on the 2 dutch xperia's.

hysf said:
I used this method on my X1 but it keep saying " no image files " then go to serial , any solutions? thx
Click to expand...
Click to collapse
xmoo said:
This could be a problem with you're ROM language.
My xperia was english, so had no problem. 2 Dutch xperia's had this problem.
Just flashed SPL first, then flashed the english rom. And now the sd card method works on the 2 dutch xperia's.
Click to expand...
Click to collapse
I also got the same problem when using the rom from this thread http://forum.xda-developers.com/showpost.php?p=2392404&postcount=1 but the flash of microSD method ran pretty well with this http://forum.xda-developers.com/showthread.php?t=431218&page=6

Does the device automatically reboot after it's installed? I just used this method and the device currently says:
'KOVSIMG.nbh - OK
OS - OK
Update Complete
UPDATE SUCESS'
It hasn't done anything since.

spr33 you take the battery out, put it back in and switch on

I'm having a few problems, I have the HardSPL installed but when i load the rom image on the sd card and reboot the bootloader shows a message of "no image found". Is there something im doing wrong? The sd card is formatted to fat32 and it only has the images on it

blackax said:
I'm having a few problems, I have the HardSPL installed but when i load the rom image on the sd card and reboot the bootloader shows a message of "no image found". Is there something im doing wrong? The sd card is formatted to fat32 and it only has the images on it
Click to expand...
Click to collapse
I was having the same problem as you, I tried everything finally I just used the kovsky RUU and used the pc update tool with it. it worked great. just make sure you take your sd card out before you do it or it will keep trying to search the card and say no image.

Problem X1 rom chang on english
I can't change rom on my X1 i have formated card on FAT32 my file name is ruu_signed.nbh i chnge the name on "Kovsimg.nbh" my device is set to tri color bar and on the screen i have Loading... and nothing else
can you help me ????

It works, I'm free and thank you
After weeks and weeks aof reading, reading, reading, making copious notes so that I had the process sorted from start to finish, I decided to bite the bullet tonight, yes, New Years Eve (well it is my new X1 after all ).
OliNex Hard SPL worked a charm, then during the micro SD method, the dreaded "no image file" message appears. RATS!
Numerous FAT32 processes, different ROMS and still the same message.
Tried the cable version using RUU and viola, I now sport the fantastic Touch IT v2.2 and NO VODAFONE
I would like to thank the more senior members for their cutting comments to witless noobs that made me read, search and read again.
Also to itje for his great ROM - have only just had a cursory scan so far as only just finihsed synch, and running like a dream. Donation certainly coming your way!
HAPPY NEW YEAR ONE AND ALL at XDA Developers from a very happy revitalised X1 owner!

ROM replacement
Moved original message to correct thread ...http://forum.xda-developers.com/showthread.php?t=445818&page=42
Has anyone more of an idea why the SD card method is causing so many to come up with the "No image file" message" ?
The USB version works for me, just would like to know the reason for error message - in case need to use it one day

BIG QUESTION:
Why some people can't flash from microSD card ??
I had the same issue
After a lot of trial and error, testing and testing, I arrived to this conclusion:
IMPOSSIBLE TO FLASH WITH microSD METHOD
(Nothing happens, "serial" message or "No image found" message popped up)
a) When I used an incorrect format (other than FAT32) on any brand card
b) With two Kingston cards properly formatted
I have successfuly flashed my X1 with unbranded cards and sandisk cards,
but after many attempts and format variants I NEVER achieved a successful flashing with kingston cards
Interesting...

Hi guys! i tried 2 flash my x1 ending in f***d up device.
I did the following:
1) running the hard_spl. The flashing started and at about 50% it stopped went back to the stripes screen telling me file not found...serial....all the things you guys described in the forum.
2) I created a card with a Kovsimg.nbh and restarted the device. Result was the same: File not found!!! but i did all like in the tutorial.
3) I tried again with hard_spl: First I got an Error 282 then 262. The device changes from stripes to grey screen the bar shows 0% ......thats all.
any suggestions??????????????????

Help!!!!! Flash topaz problem!!!

Hello. I have two TOPAZ devices, which both have been flashed with a custom ROM. I flashed them around 2-3 months ago. When i tried to turn one back to WM 6.5 Original, it got bricked. So :
1. Can a TOPAZ be restored to the original factory state?
1.1 If yes, how?
2. Is there anyway to unbrick a TOPAZ?
3. Should this be 4?
Excuse my english
Thanks,
Mike

Bricked??? Lets see... To flash the original ROM, do the following:
1. Extract the original downloaded ROM-file (should be an self-extracting .exe file).
2. Copy the extracted .nbh-file to the root of your sdcard and name it: TOPAIMG.nbh.
3. PowerOn phone holding the VOL-DOWN key pressed until Rainbowcolorscreen apears.
4. Press Power to start internal flashing.
5. After flashing, Softreset...
Thats it... if one of these steps fail, please describe exactly what is happening.
Greetz DN

WOW man!! That WAS a fast reply, thanks. I am at work right now, so I can't do much although, how do I extract the rom?

"2] Format your SD card into FAT32:
- go into dos and type:
format <volume> /FS:FAT32 /A:4096
3] Run Qmat to create a gold card:
- Put the formatted microSD card in the working WM device and connect via ActiveSync
- Run Qmat, Go to Hardware Forensics and select 'Generate HTC Goldcard'
- Select your bricked device's key
- Get the SD Card Serial from WINCE Device
- Save the Goldcard image to the SD Card
Now you have a SuperCID which allows you to flash any shipped ROM"
*thats from the sticky under unlocking/flashing*

Scabes24 said:
"2] Format your SD card into FAT32:
- go into dos and type:
format <volume> /FS:FAT32 /A:4096
3] Run Qmat to create a gold card:
- Put the formatted microSD card in the working WM device and connect via ActiveSync
- Run Qmat, Go to Hardware Forensics and select 'Generate HTC Goldcard'
- Select your bricked device's key
- Get the SD Card Serial from WINCE Device
- Save the Goldcard image to the SD Card
Now you have a SuperCID which allows you to flash any shipped ROM"
*thats from the sticky under unlocking/flashing*
Click to expand...
Click to collapse
thanks for the quick responce. so let me get this straight,
: i format my MicroSD
I connect it to my PC and with Qmat I Generate an HTC Goldcard
*didnt get this part* my bricked device's key? how do I do that?
then I use WINCE to get my serial(sdcard)
and now save the goldcard image to sd.
Is this correct?? thanks
Now, after i follow these steps, how do I flash the rom? same way as usual, or is it a special method?
and last, this is for unbricking?
Thanks again.
btw will the method in post 2 work for a fullyworking custom ROM device?

It seems like its basically just allowing you to connect your phone - enter bootloader - and run the .exe (TopazRUU) from your computer to flash a stock rom.
you should read the post in the first sticky, then look at "unlocking/flashing" and you will see #5 Unbricking

thanks

Is your problem solved?

yes, it is!! thanks everyone

Problem Solved - Closed Thread

is my phone broken?

hello i am having problems with flashing a custom ROM. I've formatted a micro sd its 2GB. Then I added the ROM file, renamed it to kovsimg.nbh and started the phone as stated (by pressing the vol down button). Then the tri colour screen pops up then a quick screen comes which says no image path I have also... installed the hard spl thingy. Where am I going wrong? Please help !!!all want is reinsstal my xperia x-1 a new windows 6.1 how i can do this plz help my phone is give me this alert SİMCARD NOT İNSERTED'' Plz help me

Do you have press and hold the vol down and the power until the screen show"loading"???

i did bur it says no image ...what i can do?

Says no image??I don't have this problem...so I can't help you,sorry...

Hello you're not alone in the dark
My Xperia do it in the same way. So i hope we will get an answer.
Additional i have problems to use the Internet yet. After receiving a config SMS the applications which are using internetdata didn't get some. The connecting to provider or wifi seem OK but no data for the application.

Provided the card is read, make sure you formatted your card properly with FAT32 and placed renamed ROM file into the ROOT.

It's possible to read the card (after booting the phone). The card is Fat32 fomatted and the imagename is set. But it's not only the problem to flash using the CD-card. Also trying by using the sync-methode will fail. I get the splashscreen with the bar showing the percentage. In the state of 0% i get an error message. No recovery is needed, but i never get the phone flashed.

My problems is exackly the same

If it doesn't work use the USB method, it always works.

Hi VingZTV,
You're wrong please read my post #7 in this thread.
I called it sync method, cause you are using active sync.
cu HAndi

I encountered this problem too. My present X1 (3rd already) refused to hardSPL or do anything with both PC (stucked at 0%, connection errors etc) and SD method ("no image file" later stuck at "loading"). Previous ones worked with either SD or PC method
This time I tried different cables and PCs and couldn't hardSPL
nor was the SD card method working, tried different cards and formatted one to fat32 before putting image file
it seems the problem might be on X1's where SPL is stock 0.78 ?
Anyways for me it worked finally when I tried hardSPL with RUU to 0.52olinex ("X1_HardSPL.exe" file) on a different PC and cable with a formatted card inserted where 0.78olinex was renamed to kovsimg.nbh (so ready to flash hardSPL with SD method which didn't work befere). The phone was set to bootloader by the program and then started flashing the image on the SD! (the program reported error as usual)
phone flashed it once, restarted, did it again and was ready!
Then I had no problem to flash a ROM with SD method normally
So I don't know what could be the reason it worked or it was a coincidence maybe try to:
WARNING: AS ALWAYS YOU DO IT ON YOUR OWN RISK!
- insert a freshly formatted card with hardSPL file (0.78olinex perhaps) renamed to kovsimg.nbh
- sync with PC and try to hardspl PC way like above and maybe the phone will finally flash the SPL from the SD
- let us know if it worked

It still doesn't work
I used 128m microSD and formated to FAT32, only copy 0.78RUU_Signed.nbh to SD card, renamed to kovsimg.nbh. After I used VOL- and power bottom. It only showed me loading.....
I also tried 0.72, looks same. DID I do some thing wrong?
Thank you very for any response!

wmw6608 said:
I also tried 0.72, looks same. DID I do some thing wrong?
Thank you very for any response!
Click to expand...
Click to collapse
Try the way described above by me (leave the card with the image and use X1_HardSPL.exe to try to change SPL and so force phone to bootloader mode)

Btw i cant boot into windows
only freeze at SE logo
Any solution

kainjinez said:
Btw i cant boot into windows
only freeze at SE logo
Any solution
Click to expand...
Click to collapse
HardSPL and reflash
Try the way described in my post above if u have probles

Agreed I also tried already with the same method
Sent from my LT15i using xda premium

I cannot flash my Xperia X1 with Custom ROM

I cannot flash my phone with custom rom. I was taking all the steps from BioVolt tutorial but all i get when loaded in bootloader is tricolor bootloader that tells me KOVS110 SPL-0.72.OliNex MicroP1-787 MicroP2-707 and Serial. I have changed the name of custom_RUU and it did not help me. What shoul I do to flash it?

Where have you stored the rom image you want to flash? Don't place it in a subfolder of your storage card. And what is the name of your image file after you renamed it?

Your new ROM must be in root of card and it must have name Kovsimg.nbh

i'm also a novice; have done all as per tutorial by "Milancex" but same way after showing three color screen and info about my SPL and Radio...a white screen comes and says "Loading" and after that nothing.
this file "kovsimg.nbh" is on root of my memory card; but it does have other files and folders of my data

iffi302 said:
i'm also a novice; have done all as per tutorial by "Milancex" but same way after showing three color screen and info about my SPL and Radio...a white screen comes and says "Loading" and after that nothing.
this file "kovsimg.nbh" is on root of my memory card; but it does have other files and folders of my data
Click to expand...
Click to collapse
Well somehow, using Task29 and as per BioVolt's video tutorial, i'm able to format internal memory; copied the "kovsimg.nbh" to my memory root; my SPL has changed as per video tutorial; but when mobile restarts in 3colored screen its says no image file found. While i know i've formated my card and it has only one file wid above name...

iffi302 said:
Well somehow, using Task29 and as per BioVolt's video tutorial, i'm able to format internal memory; copied the "kovsimg.nbh" to my memory root; my SPL has changed as per video tutorial; but when mobile restarts in 3colored screen its says no image file found. While i know i've formated my card and it has only one file wid above name...
Click to expand...
Click to collapse
I never needed to do the Task29 stuff BTW....
Have you read the thread about the "Micro SD method"?
Once you have your X1 hardSPL'd it is sufficient to
power off (remove battery for 2 seconds, reinsert)
insert µSD with KOVSIMG.nbh in root (regardless of other stuff on card, doublecheck in cardreader on PC that the file is there and has correct name)
press and hold "volume down" button, press and hold power button until tri-color screen appears
If this doesn't work you might have copied/renamed the wrong file....

thanx louis; just reformatted my SD card and copied the file again and here i go; i'm happy wid the new rom ; thanx to all...

help
im really newbie in this progress... im so excited wanna flash my rom... but sadly im still not know how to unlock my xperia x1.... my pc doesnt recognize my device.. sorry for my bad english...

amarello said:
but sadly im still not know how to unlock my xperia x1
Click to expand...
Click to collapse
this forum has an excellent search - and google offers a similar functionality.....
.... my pc doesnt recognize my device..
Click to expand...
Click to collapse
same as above, plus: You need Windows and ActiveSync (for XP) - I just don't recall the exact name of the Device Management in Windows > XP.
Once you got your PC connected to the phone start thinking about the rest.....