Related
I've been trying to get my old extended rom and new Qtek OS on my Wizard (Vario).
But now it gets stuck in the spash screen (ie the one giving the ROM numbers).
I've tried putting the wizard into bootloader mode and I can flash RUU's but when it resets it still gets stuck on the spash screen and won't go any further !!!????
What can I do ??
Please Help
Cheers
John
I should say that I had flashed using button's ROM RUU_Wizard_1050412_WWE_101_11210_WWE.exe.html
and this worked fine!
I then copied across my T-mobile Extended ROM and again everything seemed OK.
BUT then I tried to restore my new saved OS ROM using aWizard and this caused a freeze on my Wizard. It was after a hard reset that the wizard stopped at the splash screen.
Now of course I'm limited in my options because Activesync won't work until the Wizard has fully booted up.
I have tried setting the Wizard into bootloader mode and tried several ROM's (RUU Installer ones) but every time the correct splash screen comes up with the new ROM numbers but that is as far as it gets.
I also noticed on hard reset that you get the following message
Format FAT partition
Format failed
it then goes to the splash screen as before.
Are there any other things I can try Or will I have to send it back to T-mobile for a replacement??
(It's only 2 months old and I have re-flashed it with the orginal T-mobile ROM - but still won't go past the splash screen!!)
I live in hope
John
I have this EXACT same problem!
I can reflash any ROM but it will not go past the splash screen. Only difference was I wasn't playing with my extended ROM. I flashed the AKU2 QTEK ROM yesterday and have been fine through several soft resets, etc. This last time I was uninstalling phonealarm and after a soft reset I got a "could not find smswakeup.exe" (or something similar) and it's been stuck ever since! I also get the "Format Failed" message. Can anyone help!?
I think I'm going to have to send it back to T-mobile and hope they give me a replacement. Something is wrong, it doesn't seem to make any difference what ROM I used.
I think I'll reload the T-mobile shipped ROM grom the FTP site and send it back - and claim ignorance that it it suddenlt freezed and now won't boot up! - Bummer!!!
Right I've logged a fault and it will be sent back - let's hope T-mobile can't detect it's been unlocked and had several ROM updates - I suspect they will try a ROM update themselves then give up ???
The worrying thing though is that it IS possible to kill your phone with updates - maybe it was when I used aWizard to try and restore a ROM that did it??? I'll be more carefull next time!!
this has just happened to one of the devices im flashing at the moment.... absolulty f**king raging :evil: :evil:
i wish teher was a solution!!? anyone got any ideas?
activesync wont find it, so aWizard wont work.
i can flash between 3 roms without any problems (1.5.x 1.6.x 2.x) but always hangs on the splash screen. i have flashed back to the default rom that it came installed with it so i could just send it back to o2 (only 2 days old!)
i would rather just get it sorted by myself thoough so if anyone has ANY ideas then please let me know.
thank you!
Good luck! after about 3 days of trying different types of firmware, I gave up and sent it to expansys, for repair. And it looks like they've lost the bloody thing now. :evil:
tonym001 said:
Good luck! after about 3 days of trying different types of firmware, I gave up and sent it to expansys, for repair. And it looks like they've lost the bloody thing now. :evil:
Click to expand...
Click to collapse
yup looks like i might have to give up... ohwell, no worries i will just return it back to O2...
looks like one of our sales guys wont be getting a new phone on tuesday :lol:
same problem here.
tryed to write os with awizzard after changing extended_rom.
kills phone.
format failed..
Tryed different os's from win util - failed
upgraded with sd card methode worked.
in short :
you need a working wizzard to make a os dump on sd card.
Connect to wizzard with usbterm or romupdate.exe or simular.
do a rs2all command to dump os to sd card.
stick this card in broken phone.
hold voice comm button while resetting.
On ask press voice comm button again.
it bow restores the sd backup to phone.
saved mine.....
btw sd card backup can be read ad write by pc with util ntrw.exe .
so if you don't have a working dump i can upload one.
just mail me.
grtx , arnold
hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.
FarSeide said:
hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.
Click to expand...
Click to collapse
this didn't work for me.
couls flash rom. even splash screen changed to new roms one.
but still stuck at splash...
tried it with about 4 different orgigenal roms
grtx arnold
arnoldl said:
FarSeide said:
hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.
Click to expand...
Click to collapse
this didn't work for me.
couls flash rom. even splash screen changed to new roms one.
but still stuck at splash...
tried it with about 4 different orgigenal roms
grtx arnold
Click to expand...
Click to collapse
Don't worry, I met the same problem as you before, almost lost my hope, but finally I managed to fix it.
The solution is simple, that is to find an original SD card backup image from your wizard or others, then try to restore it in the bootloader mode. In my case, it said checksum error or sth else after begin restoring, and it gave up. Then I put my wizard into bootloader mode, picked one offical released RUU package, start reflash again. Finnally, I found the wirzrd works again for me after reboot.
I guess the principle is that the SD restore will destroy some import flash data structure before it said wrong, then the RUU package will rebuilt it wholely in the next reflash.
Hope this helpful, and sorry for my bad english.
There is hope
Last week after trying to downgrade to the original Cingular ROM on my 8125 using aWizard I ended up with a device that was close to being a paperweight. At least I thought so until I read and read and finally was able to get it to the bootloader and then plugged in the USB cable and ran the RUU for the new Qtek ROM (2.17). Guess what happened, yeah it worked. To my surprise I had a perfect device after 15 minutes.
For about 3 hours I thought I was a toast. Never will I do that again.
THIS is truly heaven for me !!
I have my O2 XDA MINI S locked on the splash screen .. and i updated some ROMS to it ....BUT IT DOESNT GET THROUGH IT .... please tell me what to do in a little detailed manner .. please so that i can get my phone to work.. there is no warranty on the phone and i stay IN INDIA . SO YOU'LL ARE MY ONLY HOPE .
my email id is - [email protected]
If you have a dump of the O2 XDA MINI S ..please mail it to me
Plese tell me what to do next ? WILL TRULY APPRECIATE HELP
PLEASE SOME ONE ATLEAST MAIL ME the dump of the os SO THAT I CAN TRY THE SD CARD UPGRADING ,.,,, O2 XDA MINI S
Re: There is hope
Dear Friend
I have problem that my xda mini s stuck on O2 screen, could you help me step by step.
Thank you so much
my mail : [email protected]
Thanks friend
hellomoto_25 said:
Last week after trying to downgrade to the original Cingular ROM on my 8125 using aWizard I ended up with a device that was close to being a paperweight. At least I thought so until I read and read and finally was able to get it to the bootloader and then plugged in the USB cable and ran the RUU for the new Qtek ROM (2.17). Guess what happened, yeah it worked. To my surprise I had a perfect device after 15 minutes.
For about 3 hours I thought I was a toast. Never will I do that again.
Click to expand...
Click to collapse
Dear Friend
I have problem that my xda mini s stuck on O2 screen, could you help me step by step.
Thank you so much
my mail : [email protected]
Thanks friend
odyseus said:
I've been trying to get my old extended rom and new Qtek OS on my Wizard (Vario).
But now it gets stuck in the spash screen (ie the one giving the ROM numbers).
I've tried putting the wizard into bootloader mode and I can flash RUU's but when it resets it still gets stuck on the spash screen and won't go any further !!!????
What can I do ??
Please Help
Cheers
John
Click to expand...
Click to collapse
stuck on o2 screen helppp
Dear Friend
I have problem that my xda mini s stuck on O2 screen, could you help me step by step.I see alot of post, so complicated
Thank you so much
my mail : [email protected]
Thanks friend
flexchen said:
arnoldl said:
FarSeide said:
hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.
Click to expand...
Click to collapse
this didn't work for me.
couls flash rom. even splash screen changed to new roms one.
but still stuck at splash...
tried it with about 4 different orgigenal roms
grtx arnold
Click to expand...
Click to collapse
Don't worry, I met the same problem as you before, almost lost my hope, but finally I managed to fix it.
The solution is simple, that is to find an original SD card backup image from your wizard or others, then try to restore it in the bootloader mode. In my case, it said checksum error or sth else after begin restoring, and it gave up. Then I put my wizard into bootloader mode, picked one offical released RUU package, start reflash again. Finnally, I found the wirzrd works again for me after reboot.
I guess the principle is that the SD restore will destroy some import flash data structure before it said wrong, then the RUU package will rebuilt it wholely in the next reflash.
Hope this helpful, and sorry for my bad english.
Click to expand...
Click to collapse
how to use bootloader
could you tell me how to use mentioned bootloader for restoring the images? where can I get the software?
Please help
Hendrick
flexchen said:
arnoldl said:
FarSeide said:
hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.
Click to expand...
Click to collapse
this didn't work for me.
couls flash rom. even splash screen changed to new roms one.
but still stuck at splash...
tried it with about 4 different orgigenal roms
grtx arnold
Click to expand...
Click to collapse
Don't worry, I met the same problem as you before, almost lost my hope, but finally I managed to fix it.
The solution is simple, that is to find an original SD card backup image from your wizard or others, then try to restore it in the bootloader mode. In my case, it said checksum error or sth else after begin restoring, and it gave up. Then I put my wizard into bootloader mode, picked one offical released RUU package, start reflash again. Finnally, I found the wirzrd works again for me after reboot.
I guess the principle is that the SD restore will destroy some import flash data structure before it said wrong, then the RUU package will rebuilt it wholely in the next reflash.
Hope this helpful, and sorry for my bad english.
Click to expand...
Click to collapse
Hi Arnold
My O2 cda mini s get stuck at splash scree, I read your post, still not so understand how to solve it, could you be so kind to write me step by step, and send me some software to solve it. Your help will be so much appreciated.
Hendrick
Email: [email protected]
arnoldl said:
same problem here.
tryed to write os with awizzard after changing extended_rom.
kills phone.
format failed..
Tryed different os's from win util - failed
upgraded with sd card methode worked.
in short :
you need a working wizzard to make a os dump on sd card.
Connect to wizzard with usbterm or romupdate.exe or simular.
do a rs2all command to dump os to sd card.
stick this card in broken phone.
hold voice comm button while resetting.
On ask press voice comm button again.
it bow restores the sd backup to phone.
saved mine.....
btw sd card backup can be read ad write by pc with util ntrw.exe .
so if you don't have a working dump i can upload one.
just mail me.
grtx , arnold
Click to expand...
Click to collapse
Hello guys, let's make it short... suddenly the display of my Diamond become black and there's nothing I can do to make it on again... I tried everything: reset, remove battery... nothing! :-(
The telephone works, in fact I can receive calls and so... and it even connects through activesync. So it's a display problem for sure! :-((
Now my BIG question: I have to put it back H3G ITA original ROM (first step), that I've found on an italian forum and the original SPL that I've found here (second step), to bring the Diamond to repair.
For the ROM no probs I suppose... I'll go thru Activesync and flash it as usual, but THEN??? I won't be able to use activesync again to flash the spl, since I won't be able to set the initial configuration! :-(
Can you help me? Some ideas??? Thanks in advance!
mmm... what if someone tells me the right steps after a flash upgrade and i try to touch the screen at my best for the initial configuration???
then i could connect to activesync again maybe....
pleaaaaaaaaaaaaaaaseeeee...... give me some ideas!!! :-(((
What a shame...
i was hoping someone has an nice answer
i have exactly the same problem since yesterday - so dont worry you are not alone
you dont need to use activesync to flash
enter bootloader mode and you can connect via USB
hi,
i got oner htc hd i hard spl it and the upgrade it to windows 6.5 all was working fine but it hangs a lot the i flashed it with windows 6.1 rom then the problem came was that all is working fine but i am unable to turn phone on to acess network on phone then i updated it ti the same rom i firstly used the problem was same then i update its radio then also problem was not solved then i update it other 6.5 rom but the problem is same phone doesnt turn on so that i cant acess network plz help me its very urgent for me
Are you sure the hspl update was successful? What spl version is currently showing on your device?
yes hspl was successful
manbir said:
yes hspl was successful
Click to expand...
Click to collapse
What spl is showing?
manbir said:
hi,
i got oner htc hd i hard spl it and the upgrade it to windows 6.5 all was working fine but it hangs a lot the i flashed it with windows 6.1 rom then the problem came was that all is working fine but i am unable to turn phone on to acess network on phone then i updated it ti the same rom i firstly used the problem was same then i update its radio then also problem was not solved then i update it other 6.5 rom but the problem is same phone doesnt turn on so that i cant acess network plz help me its very urgent for me
Click to expand...
Click to collapse
Perhaps you could give a bit more information about your issue. Interesting would be:
do you get the window to enter your pin?
and do you get any error message?
Matthes42 said:
Perhaps you could give a bit more information about your issue. Interesting would be:
do you get the window to enter your pin?
and do you get any error message?
Click to expand...
Click to collapse
i dont get any error and it is also not asking for any pin
its hspl is 1.56 olinex
Ok, so you have the right spl, so that is not the problem. To understand you, you say that you can not activate the phone? Does the phone stay in flight mode? If you go to Settings (Manila tab)\Wireless Controls and turn the Phone slider on, does it turn itself off again?
You can try to run the setup again. Go to Start\Settings (All Settings)\Connections\Connection Setup and make sure your Country and Operator are correct and press Ok to setup.
ClydeB1 said:
Ok, so you have the right spl, so that is not the problem. To understand you, you say that you can not activate the phone? Does the phone stay in flight mode? If you go to Settings (Manila tab)\Wireless Controls and turn the Phone slider on, does it turn itself off again?
You can try to run the setup again. Go to Start\Settings (All Settings)\Connections\Connection Setup and make sure your Country and Operator are correct and press Ok to setup.
Click to expand...
Click to collapse
am unable to turn the phone on rest all settings of country operator also ok
Is your device perhaps not SIM locked? What rom did you have originally? Have you tried to reflash to that original version and see if the problem is resolved.
When you first flashed to the 6.5 rom did the phone work then? I know you say you had lots of freezes, but before that did the phone work on the 6.5 rom?
sounds to me like a providerlocked phone
as he stated in his first post that he also flashed back 6.1
miniterror said:
sounds to me like a providerlocked phone
as he stated in his first post that he also flashed back 6.1
Click to expand...
Click to collapse
yes i flashed back to 6.1 but phone is not provide locked its phone is not turning on and i have cheked that all sims were working fine
miniterror said:
sounds to me like a providerlocked phone
as he stated in his first post that he also flashed back 6.1
Click to expand...
Click to collapse
manbir said:
yes i flashed back to 6.1 but phone is not provide locked its phone is not turning on and i have cheked that all sims were working fine
Click to expand...
Click to collapse
Thanks I saw that you did try a 6.1 rom, but I was asking if you tried the initial original 6.1 rom. You may have tried another 6.1 rom but not the original rom that was on the phone before you started flashing.
To my other questions then, did the phone initially work when you first flashed to the 6.5 rom? If after all of this and it was initially working on the 6.5 rom, you may have a hardware problem and may need to flash back to the original rom and take it back to HTC for a service.
ClydeB1 said:
Thanks I saw that you did try a 6.1 rom, but I was asking if you tried the initial original 6.1 rom. You may have tried another 6.1 rom but not the original rom that was on the phone before you started flashing.
To my other questions then, did the phone initially work when you first flashed to the 6.5 rom? If after all of this and it was initially working on the 6.5 rom, you may have a hardware problem and may need to flash back to the original rom and take it back to HTC for a service.
Click to expand...
Click to collapse
yes the phone was working fine when i firstly flashed to 6.5 rom and its not hardware how can i know which was original rom now at this condition???
manbir said:
yes the phone was working fine when i firstly flashed to 6.5 rom and its not hardware how can i know which was original rom now at this condition???
Click to expand...
Click to collapse
You can try going to the HTC website for your county and look to see if there is a rom upgrade available. If so you can enter your Serial Number to see if you can access it for download. Alternatively you can look for a stock rom here Try and find a friend near you with the HD and check their version.
Same problem here .....my wifi cant connect to anything..when im tryin to turn it on nothings happen and cant acces to web browsing..nothing works...i have flahed 4 roms till now and all the rom had the same problem...i ve flashed miris rom NRG rom Dutty rom and maryone....i dont know what to do....till before a week worked like a charm...but now it is still dead....
If your wi-fi was working and then on the same rom has suddenly stopped working that probably sounds like a hardware issue. You may need to flash back to rom and return the device for a service.
are you serious??cause in my country i leave in greece salonica..and the htc center is in athens and must send the device there and they told me to wait about one month or two to get it back....no way...!!!!but it is very strange...when i had miris rom it worked like a charm..after trying to flash a new rom to nrg then wifi stopped workin...tryed to flash another rom like duttys and maryone and still the same....why am i so unlucky???is there any solution???maybe is that any problem with rom?or misiing some file?
anyway thanks for reply....have a nice and a happy new year...god bless you!!
pm...sorry for my english...
edangel said:
are you serious??cause in my country i leave in greece salonica..and the htc center is in athens and must send the device there and they told me to wait about one month or two to get it back....no way...!!!!but it is very strange...when i had miris rom it worked like a charm..after trying to flash a new rom to nrg then wifi stopped workin...tryed to flash another rom like duttys and maryone and still the same....why am i so unlucky???is there any solution???maybe is that any problem with rom?or misiing some file?
anyway thanks for reply....have a nice and a happy new year...god bless you!!
pm...sorry for my english...
Click to expand...
Click to collapse
You can always try going back to the miri rom you were using, or to the original rom that was on the phone. If wi-fi still does not work then it sounds like it is a hardware issue and there is no other way around it that I can see but to take it in for a service, unless you think you can replace the part yourself. Is there no cell phone repair services in your location, although you may need to pay to have it repaired then as it will not be under HTC warranty then if you are prepared to take that chance. Sometimes these parts just break, it doesn't happen all the time, but hey even multi-million $ F1 cars break down.
ClydeB1 said:
You can always try going back to the miri rom you were using, or to the original rom that was on the phone. If wi-fi still does not work then it sounds like it is a hardware issue and there is no other way around it that I can see but to take it in for a service, unless you think you can replace the part yourself. Is there no cell phone repair services in your location, although you may need to pay to have it repaired then as it will not be under HTC warranty then if you are prepared to take that chance. Sometimes these parts just break, it doesn't happen all the time, but hey even multi-million $ F1 cars break down.
Click to expand...
Click to collapse
SO...FOR MANY HOURS TO FIND SOMETHING I MADE IT...THE SOLUTION IS UNDER START SETTINGS CONNECTION ADVANCED NETWORK AND THEN I JUST ENABLE FROM HSDPA/HSUPA TO ONLY HSDPA AND NOW ITS WORKING...
AS I THOUGHT THIS SETTINGS DEPENDS OF WHAT MODEM ROUTER YOU HAVE...JUST WORKING FINE NOW.....
SO EVEN MULTI MILLION F1 CAN BE FIXED UP......if you are rich and got the money...hahahaha
SO THANKS ANYWAY!!!!!!!!I AM GLAD FOR TRYING TO HELP ME.....
edangel said:
SO...FOR MANY HOURS TO FIND SOMETHING I MADE IT...THE SOLUTION IS UNDER START SETTINGS CONNECTION ADVANCED NETWORK AND THEN I JUST ENABLE FROM HSDPA/HSUPA TO ONLY HSDPA AND NOW ITS WORKING...
AS I THOUGHT THIS SETTINGS DEPENDS OF WHAT MODEM ROUTER YOU HAVE...JUST WORKING FINE NOW.....
SO EVEN MULTI MILLION F1 CAN BE FIXED UP......if you are rich and got the money...hahahaha
SO THANKS ANYWAY!!!!!!!!I AM GLAD FOR TRYING TO HELP ME.....
Click to expand...
Click to collapse
Hey, I'm glad you got it sorted. I'll remember to add that additional check to my little arsenal of things for troubleshooting. Thanks for the feedback.
Hi guys!
I have been trying everything that I could find on XDA to fix my problem.
I got this HTC clone a few weeks ago, and it was working fine.
I decided to install a UI on it and it worked fine. After a while I got bored of the UI, so I decided to uninstall it. After the uninstall, the device indicated that it needed to be restarted. I did that, but after it rebooted, it started to reinstall Windows Mobile 6.1. I was annoyed by this, but was like, whatever, and let it continue.
Where the real problem started was when the device froze up (I left it alone for over an hour, but there was no change).
I then had to pull the battery. After I put the battery back into the T5355 it just keeps getting stuck on the "TOUCH Diamond2" screen.
I tried all the hard reset and soft reset tricks I could find and have no been able to either setting it back to factory or bootloader mode.
I was able to find a post that described how to place the boo.ini, flash.bin, and loader.bin file onto my micro sd card. I was able to to get the boot.ini an flash.bin files, but can't seem to find a loader.bin file (it that the actual OS rom?). I then found a post that showed how to use HiSilicon IDT to force the install of the OS Bin file (C02_HTC_20091102_R2127_英全视角B包.bin).
I followed the instructions on placing the T5355 into "Download" mode and pushing the OS bin fine to it.
I am able get the IDT software to detect the T5355 and start pushing the install, but the damned thing ends up giving an XLDR error.
PLEASE! PLEASE! Somebody help me! This phone is brand new and really want to get it working again.
Model: HTC(?) T5355
Please help me someone!!
Is there anyone out there that can help me???
I am so frustrated and can think of what else to do!
The biggest problem I have is that I can't use ActiveSync. If I could use that I wouldn't have much trouble.
Does anyone know how to use HiSilicon's IDT properly? The instructions I was working off of are in Russian. I think that a need a loader.bin file for the T5355 that I can put on my micro sd card...or maybe not...I don't know.
I just really want to get this device back to factory settings.
Please someone take pity on me!!!
enter bootloader [those orizontal strange colors]
try flashing a new rom. you may search and download the original 6.5 build from HTC
to enter bootloader, press "volume down + shutdown button" and then flash the rom
ATENTION: plug the USB cable, wait a few seconds, you should see USB on the lowest white color, then do the flashing job
I don't think you would be experiencing these problems with an original topaz
Please take care this is a HTC CLONE
Pisca said:
Please take care this is a HTC CLONE
Click to expand...
Click to collapse
oups, I'm high resolution on monitor, I thought it was saying "done" not "clone" ) ... there's a thread dedicated to china clones, look here http://forum.xda-developers.com/showthread.php?t=619643
run with a rom in bootloader, it shud work
enter bootloader [those orizontal strange colors]
try flashing a new rom. you may search and download the original 6.5 build from HTC
to enter bootloader, press "volume down + shutdown button" and then flash the rom
ATENTION: plug the USB cable, wait a few seconds, you should see USB on the lowest white color, then do the flashing job
Click to expand...
Click to collapse
DalvuS, thanks for the reply, but the issue is that I can't seem to get into bootloader mode . I wish I could. The T5355 seems to be stuck in the middle of wm 6.1 install. I need to somehow wipe the install and be able to push a reinstall back to the device.
I don't think you would be experiencing these problems with an original topaz
Click to expand...
Click to collapse
Exca that comment doesn't help me. It just makes me more sad. I was gipped when I bought the phone . I thought I paid for a "real" Diamond 2.
If you can't to catch the bootmode, looks like hardware problem.
You can't to repair it at home, imho. Try the specialized service.
..............
... and: are you sure about key combination for bootloader screen for CLONE?
Hello people, how can i dump my rom from my phone (mfu w71) for backup, because i cannot find any rom in english only in chinese. I started to dump the chinese rom with some chinese kitchen (K3系列ROM工具), but i'm stuck. I do not know to do anymore i have extracted ROM, SYS folder. I think it would be good to start another section on this forum for the chinese phones.
Some help from experienced cookers would me be much apreciated.
My T5355 is up and working!!!
Thanks to everyone who replied to my post!!!
I discovered that the problem was that the PC I was attempting the install from was running an AMD based processor.
I tried on the family laptop (which runs an Intel processor) and the install worked!
I AM SOOOO HAPPY!!!
b0gdi good luck with your issue. Try doing a search here in XDA for "dump my phone".
nothing[switched off] -> press start -> command -> bootloader -> bootloader commands -> system start -> play
checking one by one by interfering would have done the trick
I'm glad to hear that... so now you're ok
NEXT !
help me please
i Have Flash my phone 100 times with IDT for WM6.5 and WM6.1 all the versions my phone is T5355 Hot D2 but in one day i flash a rom that kill my phone the phone are conntinue to work but no screen picture only light i have try some russian Rom that kill my phone
the phone was been on guerant so i send him back to my supplier thay fix the phone but the factory said that thay need to change the screen so now thay really change the screen and the phone back to me with WM6.1 some New version 20.1.2010 some think like this i have made a call but the phone hang up and not make calls so i try to put him Back the WM6.5 English ROM that i use with this phone before i try to Flash Russian ROM that brake me the picture of the phone and block me the Bootloader Combination of SEnd+End+Power so that way i send him to repair .
so i try the English Rom that i have use before he DOwnload the Flash Fine but now the screen are stop to show picture But the Bootloader are work fine
so i try all the Roms that i have and all the same the screen dont want to show picture
some body have a same problem or can help me with this ?
Hi Guys,
I have a great Problem with my XDA Diamond! Since one month my touchsreen didnt response! At the moment runs olinex 1.40 at the pda. I have flashed the newest o2 rom and that work without a problem! But i cant start my device because the first adjust doesent work.... (touchscreen dosent work). I tryed Hard-SPL Unlocker post 39 that i can send my device back to the O2...
but at the process on the screen of my pc i have 0% for a time than came Error 202: connection....
activesync is ok!
I have tryed to update the olinex but the same problem ...
also with other roms...
I hope anyone of you have a idea because i wanna have my pda back ....
sorry for my bad english!
Thanks a lot!!!
L3xX
If Your touchscreen doesnt response, i think it would be a external problem. Did you drop it?Water spill...Maybe try flashing a new rom like Energy Rom 6.5 with maila 2.5(sense 2.5 UI) I just got my CDMA Diamond this Saturday. Great phone with the Windows Phone 6.5 Rom. Sorry but i tried to help but couldn't. If u have a warranty try to e-mail or contact HTC, maybe they might send you back A HTC HD2! Oh the link for Energy Rom is at PPC GEEKS - http://forum.ppcgeeks.com/showthread.php?t=74084
I had the same problem
There are two different ways I fixed mine
1) Press and hold the power button + volume down + enter button (menu) while holding press the rest with the stylist. continuing to hold the buttons until a white screen comes up allowing you to hard rest the device.
2) If 1) doesn't work try try unlocking your phone again then putting a new rom on it. (this will work as long as your phone will connect to the computer, with two beeps)
well I hope this helps
Hi great thank to you! but this steps i´ve allready done!.
Bevor i can give my device into de warranty i musst flash the normal bootloader!!! in my eyes this Hard-SPL Unlocker
But this dosent work!