Database Develop

Help Please ! Won't go past the Splash Screen?

I've been trying to get my old extended rom and new Qtek OS on my Wizard (Vario).
But now it gets stuck in the spash screen (ie the one giving the ROM numbers).
I've tried putting the wizard into bootloader mode and I can flash RUU's but when it resets it still gets stuck on the spash screen and won't go any further !!!????
What can I do ??
Please Help
Cheers
John

I should say that I had flashed using button's ROM RUU_Wizard_1050412_WWE_101_11210_WWE.exe.html
and this worked fine!
I then copied across my T-mobile Extended ROM and again everything seemed OK.
BUT then I tried to restore my new saved OS ROM using aWizard and this caused a freeze on my Wizard. It was after a hard reset that the wizard stopped at the splash screen.
Now of course I'm limited in my options because Activesync won't work until the Wizard has fully booted up.
I have tried setting the Wizard into bootloader mode and tried several ROM's (RUU Installer ones) but every time the correct splash screen comes up with the new ROM numbers but that is as far as it gets.
I also noticed on hard reset that you get the following message
Format FAT partition
Format failed
it then goes to the splash screen as before.
Are there any other things I can try Or will I have to send it back to T-mobile for a replacement??
(It's only 2 months old and I have re-flashed it with the orginal T-mobile ROM - but still won't go past the splash screen!!)
I live in hope
John

I have this EXACT same problem!
I can reflash any ROM but it will not go past the splash screen. Only difference was I wasn't playing with my extended ROM. I flashed the AKU2 QTEK ROM yesterday and have been fine through several soft resets, etc. This last time I was uninstalling phonealarm and after a soft reset I got a "could not find smswakeup.exe" (or something similar) and it's been stuck ever since! I also get the "Format Failed" message. Can anyone help!?

I think I'm going to have to send it back to T-mobile and hope they give me a replacement. Something is wrong, it doesn't seem to make any difference what ROM I used.
I think I'll reload the T-mobile shipped ROM grom the FTP site and send it back - and claim ignorance that it it suddenlt freezed and now won't boot up! - Bummer!!!

Right I've logged a fault and it will be sent back - let's hope T-mobile can't detect it's been unlocked and had several ROM updates - I suspect they will try a ROM update themselves then give up ???
The worrying thing though is that it IS possible to kill your phone with updates - maybe it was when I used aWizard to try and restore a ROM that did it??? I'll be more carefull next time!!

this has just happened to one of the devices im flashing at the moment.... absolulty f**king raging :evil: :evil:
i wish teher was a solution!!? anyone got any ideas?
activesync wont find it, so aWizard wont work.
i can flash between 3 roms without any problems (1.5.x 1.6.x 2.x) but always hangs on the splash screen. i have flashed back to the default rom that it came installed with it so i could just send it back to o2 (only 2 days old!)
i would rather just get it sorted by myself thoough so if anyone has ANY ideas then please let me know.
thank you!

Good luck! after about 3 days of trying different types of firmware, I gave up and sent it to expansys, for repair. And it looks like they've lost the bloody thing now. :evil:

tonym001 said:
Good luck! after about 3 days of trying different types of firmware, I gave up and sent it to expansys, for repair. And it looks like they've lost the bloody thing now. :evil:
Click to expand...
Click to collapse
yup looks like i might have to give up... ohwell, no worries i will just return it back to O2...
looks like one of our sales guys wont be getting a new phone on tuesday :lol:

same problem here.
tryed to write os with awizzard after changing extended_rom.
kills phone.
format failed..
Tryed different os's from win util - failed
upgraded with sd card methode worked.
in short :
you need a working wizzard to make a os dump on sd card.
Connect to wizzard with usbterm or romupdate.exe or simular.
do a rs2all command to dump os to sd card.
stick this card in broken phone.
hold voice comm button while resetting.
On ask press voice comm button again.
it bow restores the sd backup to phone.
saved mine.....
btw sd card backup can be read ad write by pc with util ntrw.exe .
so if you don't have a working dump i can upload one.
just mail me.
grtx , arnold

hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.

FarSeide said:
hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.
Click to expand...
Click to collapse
this didn't work for me.
couls flash rom. even splash screen changed to new roms one.
but still stuck at splash...
tried it with about 4 different orgigenal roms
grtx arnold

arnoldl said:
FarSeide said:
hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.
Click to expand...
Click to collapse
this didn't work for me.
couls flash rom. even splash screen changed to new roms one.
but still stuck at splash...
tried it with about 4 different orgigenal roms
grtx arnold
Click to expand...
Click to collapse
Don't worry, I met the same problem as you before, almost lost my hope, but finally I managed to fix it.
The solution is simple, that is to find an original SD card backup image from your wizard or others, then try to restore it in the bootloader mode. In my case, it said checksum error or sth else after begin restoring, and it gave up. Then I put my wizard into bootloader mode, picked one offical released RUU package, start reflash again. Finnally, I found the wirzrd works again for me after reboot.
I guess the principle is that the SD restore will destroy some import flash data structure before it said wrong, then the RUU package will rebuilt it wholely in the next reflash.
Hope this helpful, and sorry for my bad english.

There is hope
Last week after trying to downgrade to the original Cingular ROM on my 8125 using aWizard I ended up with a device that was close to being a paperweight. At least I thought so until I read and read and finally was able to get it to the bootloader and then plugged in the USB cable and ran the RUU for the new Qtek ROM (2.17). Guess what happened, yeah it worked. To my surprise I had a perfect device after 15 minutes.
For about 3 hours I thought I was a toast. Never will I do that again.

THIS is truly heaven for me !!
I have my O2 XDA MINI S locked on the splash screen .. and i updated some ROMS to it ....BUT IT DOESNT GET THROUGH IT .... please tell me what to do in a little detailed manner .. please so that i can get my phone to work.. there is no warranty on the phone and i stay IN INDIA . SO YOU'LL ARE MY ONLY HOPE .
my email id is - [email protected]
If you have a dump of the O2 XDA MINI S ..please mail it to me
Plese tell me what to do next ? WILL TRULY APPRECIATE HELP

PLEASE SOME ONE ATLEAST MAIL ME the dump of the os SO THAT I CAN TRY THE SD CARD UPGRADING ,.,,, O2 XDA MINI S

Re: There is hope
Dear Friend
I have problem that my xda mini s stuck on O2 screen, could you help me step by step.
Thank you so much
my mail : [email protected]
Thanks friend
hellomoto_25 said:
Last week after trying to downgrade to the original Cingular ROM on my 8125 using aWizard I ended up with a device that was close to being a paperweight. At least I thought so until I read and read and finally was able to get it to the bootloader and then plugged in the USB cable and ran the RUU for the new Qtek ROM (2.17). Guess what happened, yeah it worked. To my surprise I had a perfect device after 15 minutes.
For about 3 hours I thought I was a toast. Never will I do that again.
Click to expand...
Click to collapse

Dear Friend
I have problem that my xda mini s stuck on O2 screen, could you help me step by step.
Thank you so much
my mail : [email protected]
Thanks friend
odyseus said:
I've been trying to get my old extended rom and new Qtek OS on my Wizard (Vario).
But now it gets stuck in the spash screen (ie the one giving the ROM numbers).
I've tried putting the wizard into bootloader mode and I can flash RUU's but when it resets it still gets stuck on the spash screen and won't go any further !!!????
What can I do ??
Please Help
Cheers
John
Click to expand...
Click to collapse

stuck on o2 screen helppp
Dear Friend
I have problem that my xda mini s stuck on O2 screen, could you help me step by step.I see alot of post, so complicated
Thank you so much
my mail : [email protected]
Thanks friend
flexchen said:
arnoldl said:
FarSeide said:
hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.
Click to expand...
Click to collapse
this didn't work for me.
couls flash rom. even splash screen changed to new roms one.
but still stuck at splash...
tried it with about 4 different orgigenal roms
grtx arnold
Click to expand...
Click to collapse
Don't worry, I met the same problem as you before, almost lost my hope, but finally I managed to fix it.
The solution is simple, that is to find an original SD card backup image from your wizard or others, then try to restore it in the bootloader mode. In my case, it said checksum error or sth else after begin restoring, and it gave up. Then I put my wizard into bootloader mode, picked one offical released RUU package, start reflash again. Finnally, I found the wirzrd works again for me after reboot.
I guess the principle is that the SD restore will destroy some import flash data structure before it said wrong, then the RUU package will rebuilt it wholely in the next reflash.
Hope this helpful, and sorry for my bad english.
Click to expand...
Click to collapse

how to use bootloader
could you tell me how to use mentioned bootloader for restoring the images? where can I get the software?
Please help
Hendrick
flexchen said:
arnoldl said:
FarSeide said:
hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.
Click to expand...
Click to collapse
this didn't work for me.
couls flash rom. even splash screen changed to new roms one.
but still stuck at splash...
tried it with about 4 different orgigenal roms
grtx arnold
Click to expand...
Click to collapse
Don't worry, I met the same problem as you before, almost lost my hope, but finally I managed to fix it.
The solution is simple, that is to find an original SD card backup image from your wizard or others, then try to restore it in the bootloader mode. In my case, it said checksum error or sth else after begin restoring, and it gave up. Then I put my wizard into bootloader mode, picked one offical released RUU package, start reflash again. Finnally, I found the wirzrd works again for me after reboot.
I guess the principle is that the SD restore will destroy some import flash data structure before it said wrong, then the RUU package will rebuilt it wholely in the next reflash.
Hope this helpful, and sorry for my bad english.
Click to expand...
Click to collapse

Hi Arnold
My O2 cda mini s get stuck at splash scree, I read your post, still not so understand how to solve it, could you be so kind to write me step by step, and send me some software to solve it. Your help will be so much appreciated.
Hendrick
Email: [email protected]
arnoldl said:
same problem here.
tryed to write os with awizzard after changing extended_rom.
kills phone.
format failed..
Tryed different os's from win util - failed
upgraded with sd card methode worked.
in short :
you need a working wizzard to make a os dump on sd card.
Connect to wizzard with usbterm or romupdate.exe or simular.
do a rs2all command to dump os to sd card.
stick this card in broken phone.
hold voice comm button while resetting.
On ask press voice comm button again.
it bow restores the sd backup to phone.
saved mine.....
btw sd card backup can be read ad write by pc with util ntrw.exe .
so if you don't have a working dump i can upload one.
just mail me.
grtx , arnold
Click to expand...
Click to collapse

A Big Problem with HTC Wizard

Hello. I was flashed my Wizard,but I have a general problem. When I try to start Windows, always start Align Screen, but Windows didn't start. I reflash my pocket, but the situation is a same. I think that I'm lost my BootLoader on PDA and the Wizard is unrepaired. I want somebody to help me, please?

bootloader
you can go into bootloader by soft reseting and holding the camera button down at the same time it will the show a multi colour screen that is bootloader mode
download your network providers official rom re flash it then is hsould bo ok
otherwise use a rom called wizard love i have seen use on many threads and it usually get people out of trouble search for it on goole
or if you have onshare i have the rom you can download my id is easymob same as the forum
http://www.onshare.com/en_gb/download/

What ROM did you flash with?

mordo said:
Hello. I was flashed my Wizard,but I have a general problem. When I try to start Windows, always start Align Screen, but Windows didn't start. I reflash my pocket, but the situation is a same. I think that I'm lost my BootLoader on PDA and the Wizard is unrepaired. I want somebody to help me, please?
Click to expand...
Click to collapse
You need to provide more details if you want help... what ROM version were you flashing? What provider? What was your IPL/SPL?

This is a beginner's mis conception. I was having the same problem. Eventually I found out that I need to keep holding the stylus on the screen for at least 6-8 seconds. Then the pointer will start moving. So it was not "tapping".

Think I have killed my dad's phone !! HELP

Was updating my dads SPV M700 to WM6 and have hit a problem ....
The rom image updated ok, and I used AX3L's 2.0.8.
Unfortunately during the GSM update the software crashed, and froze at 51%. I had to re-boot and now I can't use the phone.
When I re-set the phone it says No GSM at the HTC screen and then stops loading at the WM6 front page.
I can get into the Bootloader by pressing the Power/Camera/Reset buttons, but when I try to re-flash GSM is says error 270, corrupt image. I have tried several files with no luck.
I would appreciate a hand ..... My dad is going to kill me
Thanks
gaz_az

try press
power button + camera + reset
to enter usb mode
then reflash the radio again.
hope this works

You can try 2 other things!
Download the Radio ROM again- you may have had a downlaod glitch in the 1st one. V1.38 is the best one to try.
Download and install the offical HTC WM5 ROM- this should be a full ROM including Radio, so sometimes completes more effectively. If you are brave, you can them retry the WM6 flash!

since bricking a hermes i stopped taking chances doing rom upgrades via usb..
the method that is most reliable ad safe is... via SD card
extract RUU_signed file from the upgrade pack (use winrar) and then copy it to the root of a blank sd (mini or micro etc) and rename to TRINIMG.nbh ..enter bootloader and follow the steps.. its fast and most reliable

Ok - Thanks for the help, but no luck so far. I have tried the suggestions above !
Heres what I have done ...
Hard reset - no change
Tried to re-flash with WM6 and WM5 cooked roms, but an error comes up saying the images are corrupt. This happens with any image I try.
I have also tried a legit HTC WM5 rom upgrade image, but it doesn't work either. It gives an error at 1% saying invalid device ID.
What I can do it get into the standard bootloader screen, which shows I have a USB connection when plugged in. If I allow the phone to boot up it stops at the WM6.0 picture. It won't go far enough to allow me to get an activesync connection.
ANy more adivice would be greatly appreciated !
gaz_az

Next thing then, is to try and obtain a downloaded Orange M700 ROM- there are a few links hereabouts.
For some reason, your device seems to want only its home ROM. If that fails there are other methods before sending back to Orange!

I downloaded an Orange rom, but still no luck. It gets to 1% again, then says there is a error/corrupt image file. Same as any of other cooked images !
What next ??

well if you were my son, i would advice you,to buy a plane ticket for somewhere very far,leave the house while i sleep,and pray every day you have left in your life,for not find you on my way

uhm, question about boot loader and flash on boot loader mode.
I copy file TRINIMG.nbh to root card mini SD, and i can't go as you say...
always Tri colors screen....

gaz_az said:
I downloaded an Orange rom, but still no luck. It gets to 1% again, then says there is a error/corrupt image file. Same as any of other cooked images !
What next ??
Click to expand...
Click to collapse
You are running out of options
Your choices now are to go further down the 'fiddling' route, or give up and return the phone to Orange for repair. At least if its is stuck in bootloader, they may not spot that you have been meddling
If you want to play more, there are very few Trinity specific fixes, but possibly some of the questions/answers in the Hermes WiKi may help, though the Bootloader versions etc won't be relevant.
[Edit: When you are in Bootloader mode, what version numbers are showing on the screen?]

is it so wrong i was smiling when i read this.
does make me wonder if u told ur dad what u were going to do or whether u were trying to be cocky by giving him a better phone without him knowing.
all i can say is, UNLUCKY !

I must say things are looking bad - I think it would take an original orange SPV rom if I could get one. Been to the orange website, but no luck !! Anyone know if orange released one ??
Been looking at the Hermes unbrick thread. Is there a way to enter KITL debug mode in the trinity ??
G
P.S. Dad knew I was upgrading the phone, already did it once for him and it went ok. No sure he knew I could acutually kill it

No Orange haven't released an official rom.
Well Orange UK haven't Orange FR have, so unless he speaks and reads french that's not an option.

Well, French or not, you've probably got nothing to lose by trying to load the official French ROM
Go Here and click the Mise-a-jour link (which is French for ROM) and it will open a zip file download without the need to verify the IMEI number.
If that doesn't work, nothing will! If it does load, you will at least have a working phone, even if it is in French, and you can go back over the ROM update again, remembering to apply the SPL Bootloader first!

Still "not allow", i don't know what the hell Orange was doing with P3600?
Lock everything?........it's suck !!!

No luck with the French ROM. Same thing gives an error message about wrong device ID.
I am one step from chucking it in the bin. Any more last minute ideas ??

erh, bizzard,i can't use "wtty.exe" to view my CID ...
i tape "info 2"and it always appear
Cmd>info 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCE
Cmd>
...............................
Someone have issue for that?
If i can view CID code,i think i can find the right ROM to re-vivre...all suck !!!

erh, hey guy, your boot loader is english or french? sorry if it's the most stupid question of the day......i think french device use french boot loader,right?
i mean, when screen tri-color appear, use mini SD card to flash ROM, the language it apprear itself is english or french.
p/s : i was telephone to the HTC center, and they say as usual, send it to the center repair.
For french user address is : be sure u have enough garanty which required.
send them and make them crazy.....
CIRMA ELECTRONIQUE
9A14 CHEMIN DE BARATEAU
ZONE INDUSTRIEL DE LA LANDE
33451 SAINT Loubès

If you can figure out how to compile splxploit, you can fix this, see
http://forum.xda-developers.com/showthread.php?t=308691

thank anyway,i will try it before tomorrow,cause i will send them my device for repair.

this concludes the beta test...

Hello all,
first, a big thanks to all the rom developers around. You transformed my Diamond in a usable and enjoyable tool.
What happened to me tonight is very frightening. In fact, I cannot believe what happened.
And this is the story: I was at a birthday party and later in the evening I checked my phone : it seemed to have frozen, so I rebooted it as I do sometimes when I have no other choice. But this time something strange happened : I got the following message "this concludes the beta test of this software release. thank you very much for your time and effort in helping make this a great product for our customers" - what the ... ? No way to make a call, the message is impossible to remove... completely blocked !!!
I don't remember exactly the rom I flashed last because I sometimes change. It might be a dutty's release (75%M sure) - anyway I was in a very bad situation because my wife wasn't feeling well and I couldn't call her without finally borrowing a phone from someone.
I will flash a new rom tomorrow and I hope that the message will disappear but I can tell you that it is a very strange feeling when suddenly your phone refuses to operate normally. It's a nightmare.
I hope that someone has an explanation for this because I don't want to go trough this situation ever again, it's just so annoying to have a phone which tells you "No you can't use me; your trial period has expired" when you need it he most.
Thank you for your opinions in advance

Have you tried a hard reset?

Yep same problem here.
Using duttys 1.93 - Can't get to his website either.
Hard rest does not work - had to reflash back to branded (Telstra) ROM

i'm having the exact problem right now, what can i do to fix this? someone told me to reflash it but how? i'm VERY new to the diamond
hardreset does not work
I bought the phone from a person so it's second hand. The seller did mention he updated the ROM, I'm assuming this is the cause of the problem? help please
thanks!

I am getting the exact same problem.I do not know what to do.

Sigh and since my computer will not sync, I cannot reflash it. Hard set is also a no go.

ya I cant sync it with my computer either... i'm searching other sections on this forum and I cant seem to find one that teaches you how to flash without syncing with the computer

OK i got it well kinda sorta. If you hard reset and just use the date taht dutty had then your phone will load. Do not correct the date and you should also change the date on your computer so that it wont sync. Then donwload his new rom or whatever rom you prefer and then flash it. Then change the dates back. It worked for me.

thanks.. do you have the link for the new rom?
I'm going to give it a try

The link it dutt'y new rom is here http://rapidshare.com/files/162091111/Ruu_Signed_duttys_diamond__V2.9_5_2_20275_RTM_Full_MSVC.zip

just a question how do you flash it?
can you help me? i'm very new to this phone

I had the same problem last night- expired beta software. If I do a hard reset I believe I will loose all the info on the phone, is that correct?
I was thinking that changing the date will work, is there another way to change the date without having to loose the info?
Someone has a reliable link to an instruction on how to flash the ROM?
I am also using throy 2.3, to find the latest release please go to WWW.DUTTYTHROY.NET
Any help appreciated.

!everyone! you can flash roms from bootloader. hold volume down and the little red reset button, keep holding vol down untill bootloader. at the tri color screen, run ruu from host pc. everything will be fine with this method. just like activesync.

ok i to change the time and stuff and it actually can sync using active sync.. however.. when tried to install HSPL 1.24 after the part where the phone will turn black.. i click on the DiamondCustomRUU as instructed
but it says this "The application failed to initialize properly (0xc0000135). CLick on OK to terminate the application"

Is there a way I can recover this without losing all that is on my phone?

Do anybody know the password for the latest ROM 2.9 from Dutty? His page is unavailable right now....

Duttys V2.9 RTM Finale

someone please tell me how to flash.. from scratch? i hard reset my phone.. and i cant get HSPL to work. When i install the activesync way, the black screen turns on then i cant open DiamondCustomRUU
if i do i the bootloader way, when i connect from the three colour screen it cant pick up the phone because it says i'm missing Qualcomm CDMA Technologies MSM
please help been stuck for hours already

i won't flash Duttys ROM again!!! Right now i need my phone and it doesn't work! And if i reflash it i lose my data....
never again!

its you have a problem with duttys rom
you need to use his thread to point out your problems....
not this one.

touch screen does not work at all

Hello. Yesterday morning when i woke up suddenly my touch screen did not respond any more. I try reinstalling windows or hard reset but now i can not even get over tap the screen.Please help me. You already helped me once when i was going to throw it away because i thought it's a hardware problem and it was a software one.I did the soft reset and leave it for a day then it worked but when i wanted to charge, it happened again and i have the same problem now.Any way a thing it's certain it is a software problem.If you have other advice please help.

another problem
I tried installing lots of roms hoping it will be fine. but now i installed a 6.1 version of wm and when i try installing wm 6.5 it stopes in loading screen and the pc gives me an error conection.What about this?

Moved as not ROM Development.
Place a welcome.not file on root of storage card can be a .txt file but change the extension doesn't want to be welcome.not.txt this will get you past all the configs on setup.

Please be more specific
Where can i find a welcome.not file?

linucu said:
Where can i find a welcome.not file?
Click to expand...
Click to collapse
You make it out of a .txt file
Have done it 4 u.

Thank you but that was not the problem
I did as you said and it worked but that was not the problem.The problem is my touch screen not responding.And it's not a hardware problem because if i did as i have been told to fully charge the phone, then do a soft reset and leave it for a day it was as new.But when i try to charge it again i got the same not responding screen. Now after all this i have another issue and that is when i try doing a soft reset the phone resets and it sopped on gray screen with Loading... and the pc gives me error connection. So i get this only i put a 6.1wm. Is this the reason for not letting me change the wm to 6.5 one? i will go crazy with these strange things that are science but have no explanation. Where is the science then? What you did was to allow me to use the phone without touch screen. Well...thank you, but i know there is a way to get the phone normal again and that is what i need you to help me with. Thank you. Catalin

Are you Hard-SPL'd?
Regards problem if software then flashing a different ROM even stock should be able to tell you, i know you think not hardware but if repetitive then maybe you just fluked the being ok again.
Anyway flash another stock ROM, then if fine flash a 6.5, you don't have to use computer as can flash via SD.

First of all thank you
Thank you because you try to help but please talk so i can understand. What is stock rom?
"even stock should be able to tell you" what is stock?
And now i have another one. It can not connect to active sync.
tell me please how can i Flash form SD?

I can not insatll anything from pc
So i don't understand why it does not allow me to do anything like hard spl, or flash rom, or anything to install from pc. It connects to active sync and lets me access the card but when i try installing something it stops.