Related
Hi guys, i've been around sometime in the "qtek" world and had owned some of them in the past, now i own a wizard and i expect to begin mastering the thingie..
The problem is that after some experiments i have this problem :
I think it is not bricked.. it boots the OS but it is so sloowww with stops everywhere, takes like 4times the time to open "settings" than before. and it does not turn the charge light on and is not recognized by usb port so it does not sync and i'm unable to re flash it..
What i did was to downgrade it with CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE
and then i stick the AKU3.2-1.0RC1
It has been cid unlocked by me yesterday and was working fine with another rom..
I was thinking of entering bootloader manually and then somehow flash it..
Please Help
thanks !
i'm glad i solved the problem.. just entered manually in bootloader then flashed a original qtek rom and it fine now
thanks anyway, hope this help other people in this very situation
bye
cheers from portugal
W4R_M4ST3R said:
Hi guys, i've been around sometime in the "qtek" world and had owned some of them in the past, now i own a wizard and i expect to begin mastering the thingie..
The problem is that after some experiments i have this problem :
I think it is not bricked.. it boots the OS but it is so sloowww with stops everywhere, takes like 4times the time to open "settings" than before. and it does not turn the charge light on and is not recognized by usb port so it does not sync and i'm unable to re flash it..
What i did was to downgrade it with CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE
and then i stick the AKU3.2-1.0RC1
It has been cid unlocked by me yesterday and was working fine with another rom..
I was thinking of entering bootloader manually and then somehow flash it..
Please Help
thanks !
Click to expand...
Click to collapse
You can't go from 1 to 3. Re-flashing a stock ROM was a good move.
--M
Hi W4R_M4ST3R!!!
I think i have exactly the same problem as you had!
I have installed new ROM, and my T-mobile MDA Vario working veeeery slow, and i could not connect it to my computer!!!!!!
Tell me please (in details) what did you do with your phone.
Thanks!
zorrozorro said:
Hi W4R_M4ST3R!!!
I think i have exactly the same problem as you had!
I have installed new ROM, and my T-mobile MDA Vario working veeeery slow, and i could not connect it to my computer!!!!!!
Tell me please (in details) what did you do with your phone.
Thanks!
Click to expand...
Click to collapse
This topic has been discussed in length all over the forum. But, here we go again. This will be based on you having a G3 device.
1. Make sure that your device is CID unlocked. if not follow the sticky thread at the top of this forum. and read through all of it BEFORE you begin
2. make sure that you have ipl/spl 2.x
3. Now upgrade to any rom you want.
_Nomad_ said:
This topic has been discussed in length all over the forum. But, here we go again. This will be based on you having a G3 device.
1. Make sure that your device is CID unlocked. if not follow the sticky thread at the top of this forum. and read through all of it BEFORE you begin
2. make sure that you have ipl/spl 2.x
3. Now upgrade to any rom you want.
Click to expand...
Click to collapse
How can i upgrade my ROM if i could not connect my phone to the computer! The main problem is that i could not syncronise my phone and my PC.
enter bootloader mode... press the two buttons (camera & voice command) while resetting the device. you should get a screen that's red, green and blue. from there you can reflash your device. if that doesn't work, your phone is bricked
_Nomad_ said:
enter bootloader mode... press the two buttons (camera & voice command) while resetting the device. you should get a screen that's red, green and blue. from there you can reflash your device. if that doesn't work, your phone is bricked
Click to expand...
Click to collapse
Thank you!!
Could you explane me a bit more precise what does it mean bootloader and reflash? Does it mean that i can syncronise phone and computer when i have RGB on my screen?
When you've got your device in bootloader mode just plug it in and start the upgrading procedure
_Nomad_, thank you!
It works now!!
zorrozorro said:
It works now!!
Click to expand...
Click to collapse
Like music to my ears
I have a stuck image on my 8125. The phone "boots" but only shows a white screen, and is unusable.
The "a2sd all" restore option mentioned in the forums doesnt work for me. I have read on several forums that I should be able to reflash the OS from the bootloader, though I cant find any instructions on how to do this
Could someone point me in the right direction for how to flash an OS VIA bootloader?
Thx
1. Get the phone to bootloader (tree color mode) - I think by soft resetting and pressing the camera button at the same time
2. Connect it to the computer (Windows XP) with a USB cable
3. You will notice "USB" written in a lower corner of the phone (this means it is connected)
4. Now you can flash your provider's ROM without any problems
I am not sure whether the bootloader flashing is possible from Windows Vista.
You must flash normally (in bootloader you cannot use either shelltools or SoftSPL - so use your provider's ROM).
Mirek
Mirek - not to be totally ignorant, but the step 4 is what I'm having problems with .... where can I find either a providers ROM, or something that I can actually use while in bootloader mode?
Thanks!
NM ... Found it!
For anyone reading this .... You can get the provider ROM for the 8125 from HTCAmerica here: http://www.htcamerica.net/support/8125/software-downloads.html
Thanks for your help!
mirekluza said:
1. Get the phone to bootloader (tree color mode) - I think by soft resetting and pressing the camera button at the same time
2. Connect it to the computer (Windows XP) with a USB cable
3. You will notice "USB" written in a lower corner of the phone (this means it is connected)
4. Now you can flash your provider's ROM without any problems
I am not sure whether the bootloader flashing is possible from Windows Vista.
You must flash normally (in bootloader you cannot use either shelltools or SoftSPL - so use your provider's ROM).
Mirek
Click to expand...
Click to collapse
Dear Readers,
I'm having problem with my Dopod 900(,Qtek 9000,HTC Universal,O2 Xda Exec,Jasjar ). Can somebody please tell me what to do?
Before this, every time somebody called, the PDA lost the network bar and start to search or network and reject the calls automatically and also i wasn't able to send SMS. Now, i tried to install WM6 crossbow, the phone even cannot be on !!! even when i connect it to the charger, even the light will not be on. the only page that i can see is a white page asks Press 0 to Restore factory default or press X to exit. either perss 0 or X, the phone will be off and i cant turn it on with power key....
Please tell me what can i do ?? I really need your help.
PLEASE REPLY, PLEASE.
[email protected]
Warm Regards to All
G-Jorji
brick?
hey guys, i need a little help. i downgraded my phone to buttons rom and then i was gonna attempt to upgrade the ipl/slp to 2.xx. so i downloaded the wizard ipl/spl 208 from the ftp site. i had a successful flash but when it went to reboot, my wizard never turn on again. ive searched the forums but it seems to me i have a brick found nothing. has anyone had the same situation happen to them? and find a solution?
it wont turn on at all anymore
acuraholic said:
hey guys, i need a little help. i downgraded my phone to buttons rom and then i was gonna attempt to upgrade the ipl/slp to 2.xx. so i downloaded the wizard ipl/spl 208 from the ftp site. i had a successful flash but when it went to reboot, my wizard never turn on again. ive searched the forums but it seems to me i have a brick found nothing. has anyone had the same situation happen to them? and find a solution?
it wont turn on at all anymore
Click to expand...
Click to collapse
WHAT did you downgrade from?
Did you re-unlock your G3?
How's your battery?
acuraholic said:
hey guys, i need a little help. i downgraded my phone to buttons rom and then i was gonna attempt to upgrade the ipl/slp to 2.xx. so i downloaded the wizard ipl/spl 208 from the ftp site. i had a successful flash but when it went to reboot, my wizard never turn on again. ive searched the forums but it seems to me i have a brick found nothing. has anyone had the same situation happen to them? and find a solution?
it wont turn on at all anymore
Click to expand...
Click to collapse
IPL/SPL 2.08? Does that exist? Do you mean 3.08?
Are you sure your device is a G3? Or you killed it when flashing Button's ROM?
First of all i do not know where to post this. I have had a HTC wizard for over a year now. it has been working fine after cooking up wm6 and installing it for 6 months. today when i restartet the phone pulling the battery out and inserting it, the phone starts up, then the blue screen comes and shows ispl etc, then windows image shows, there it stops. i do not know what to do. It has been a while since i did pocket pc modding now, and i have forgotten all about it.
Alexander, [email protected]
Maybe something crashed the OS software.
Hope you have a system backup, or at least PIM backup using ActiveSync because what you need now is a hard reset.
Punching the reset hole (next to IR window) while holding CommManager+VoiceDial, then press "Dial" as prompted.
how do i hard reset my dash/s620?
i have tried hard reset
i have hard reset the phone. i do not have any backup in active sync. and i dont think that matters. because my phone does not connect to activesync since it does not start up. and in the three colored boot mode the phone is not detected by active sync. when i hard reset the phone it just came to the same point and freezed
If you didn't touch the ROM for long time, then it is probably a hardware failure...
lovemy318 said:
how do i hard reset my dash/s620?
Click to expand...
Click to collapse
READ YOUR PHONE MANUAL, and THIS IS NOT DASH FORUM.
hard to believe
First off, thanks for fast responses.
It cant be hardware(Not as a total theory of course) or likely not, because phone was not touched by water, shock, bumb fire or anything. it laid on my desk, worked, laid on my dask more, freezed. and it has been working for 6 months with wm6. is there anyway i can flash something into it. without activesync, but in the three colored boot mode?
Get into bootloader, plug in your usb cord and give it a minute...ON THE TRI-COLORED SCREEN do you see in the bottom corner "USB"??? If yes, you are OK. Get a stock rom such as the Tmo 2.26 and flash that. If you do not see "USB" in the bottom corner then as far as I know, you are fukd.
For more info on issues, read the linky in my siggy. There is valuable info there that may help with other ways to flash a rom.
Good luck.
i see usb
thanks, guess i am not fked then
Only problem is i have forgotten all about this now, and that i am sorry for.
But i have to ask you, as from norway wich stock rom to choose, what is stock rom, and when you say bootloader, is that an expression for the three colored screen or is that a program, that can flash in three colored screen? Thanks, i do not expect an answer on this noob questions, but i would really apreciate answers.
stock rom & bootloader
stock rom is the rom which comes with ur phone while purchasing it.. u can call it base rom..bootloader is tri-coloured screen which is bios for ppc if it gets fked then phone is bricked..next time if u cant boot up, then u can flash ur phone with the help of bootloader...
that was fast
thanks, but i do not think i have the rom that came with my mobile phone:/
and i do not know how to flash from tri colored screen, because all the files i have tried cant detect my phone.
ipl adn spl are 3.08 if that helps anything.
that was fast
is there an app you use to flash from tri colored
there is no need for any app, just connect ur phone to tri-coloured screen..u willl see usb in down left corner.. then ur phone is connected then run RUU utility.. if any problem comes i am online at hotmail... [email protected]
Can you power down? If not, remove battery for 1 seconds, the re-insert. Then press all at once the camera, comm and power buttons (or I believe you can also press the camera and soft reset. It is in the wiki explaining, as are some stock roms. Use any stock rom if you plan on flashing a cooked rom. The Tmo 2.26 is a decent stock rom, there is a 3.08 on the forum somewhere that you can also use. Get a stock rom. Get into the tri-colored bootloader. Look to see if it says usb in the bottom corner. If yes, connect your cable and using the ruu from the stock rom, flash your phone. Once a stock rom is installed follow the directions to cid/sim unlock your phone. Once unlocked, you can flash any cooked rom.
PS- I am assuming you have a G3 phone.
PPS- reading the wiki and the stickies are very helpful. Give them a try.
im sutch a noob
yeh i got same problem... i will try a hard reset but im at school... hope it fixes it... i got imate jasjam... BETTER WORK OR I WILL KILL MY BROTHER 4 STUFFING AROUND WITH MY PHONE
im sutch a noob
gah... it diddent work what do i do now????
Hello all,
first, a big thanks to all the rom developers around. You transformed my Diamond in a usable and enjoyable tool.
What happened to me tonight is very frightening. In fact, I cannot believe what happened.
And this is the story: I was at a birthday party and later in the evening I checked my phone : it seemed to have frozen, so I rebooted it as I do sometimes when I have no other choice. But this time something strange happened : I got the following message "this concludes the beta test of this software release. thank you very much for your time and effort in helping make this a great product for our customers" - what the ... ? No way to make a call, the message is impossible to remove... completely blocked !!!
I don't remember exactly the rom I flashed last because I sometimes change. It might be a dutty's release (75%M sure) - anyway I was in a very bad situation because my wife wasn't feeling well and I couldn't call her without finally borrowing a phone from someone.
I will flash a new rom tomorrow and I hope that the message will disappear but I can tell you that it is a very strange feeling when suddenly your phone refuses to operate normally. It's a nightmare.
I hope that someone has an explanation for this because I don't want to go trough this situation ever again, it's just so annoying to have a phone which tells you "No you can't use me; your trial period has expired" when you need it he most.
Thank you for your opinions in advance
Have you tried a hard reset?
Yep same problem here.
Using duttys 1.93 - Can't get to his website either.
Hard rest does not work - had to reflash back to branded (Telstra) ROM
i'm having the exact problem right now, what can i do to fix this? someone told me to reflash it but how? i'm VERY new to the diamond
hardreset does not work
I bought the phone from a person so it's second hand. The seller did mention he updated the ROM, I'm assuming this is the cause of the problem? help please
thanks!
I am getting the exact same problem.I do not know what to do.
Sigh and since my computer will not sync, I cannot reflash it. Hard set is also a no go.
ya I cant sync it with my computer either... i'm searching other sections on this forum and I cant seem to find one that teaches you how to flash without syncing with the computer
OK i got it well kinda sorta. If you hard reset and just use the date taht dutty had then your phone will load. Do not correct the date and you should also change the date on your computer so that it wont sync. Then donwload his new rom or whatever rom you prefer and then flash it. Then change the dates back. It worked for me.
thanks.. do you have the link for the new rom?
I'm going to give it a try
The link it dutt'y new rom is here http://rapidshare.com/files/162091111/Ruu_Signed_duttys_diamond__V2.9_5_2_20275_RTM_Full_MSVC.zip
just a question how do you flash it?
can you help me? i'm very new to this phone
I had the same problem last night- expired beta software. If I do a hard reset I believe I will loose all the info on the phone, is that correct?
I was thinking that changing the date will work, is there another way to change the date without having to loose the info?
Someone has a reliable link to an instruction on how to flash the ROM?
I am also using throy 2.3, to find the latest release please go to WWW.DUTTYTHROY.NET
Any help appreciated.
!everyone! you can flash roms from bootloader. hold volume down and the little red reset button, keep holding vol down untill bootloader. at the tri color screen, run ruu from host pc. everything will be fine with this method. just like activesync.
ok i to change the time and stuff and it actually can sync using active sync.. however.. when tried to install HSPL 1.24 after the part where the phone will turn black.. i click on the DiamondCustomRUU as instructed
but it says this "The application failed to initialize properly (0xc0000135). CLick on OK to terminate the application"
Is there a way I can recover this without losing all that is on my phone?
Do anybody know the password for the latest ROM 2.9 from Dutty? His page is unavailable right now....
Duttys V2.9 RTM Finale
someone please tell me how to flash.. from scratch? i hard reset my phone.. and i cant get HSPL to work. When i install the activesync way, the black screen turns on then i cant open DiamondCustomRUU
if i do i the bootloader way, when i connect from the three colour screen it cant pick up the phone because it says i'm missing Qualcomm CDMA Technologies MSM
please help been stuck for hours already
i won't flash Duttys ROM again!!! Right now i need my phone and it doesn't work! And if i reflash it i lose my data....
never again!
its you have a problem with duttys rom
you need to use his thread to point out your problems....
not this one.
Hi guys!
I have been trying everything that I could find on XDA to fix my problem.
I got this HTC clone a few weeks ago, and it was working fine.
I decided to install a UI on it and it worked fine. After a while I got bored of the UI, so I decided to uninstall it. After the uninstall, the device indicated that it needed to be restarted. I did that, but after it rebooted, it started to reinstall Windows Mobile 6.1. I was annoyed by this, but was like, whatever, and let it continue.
Where the real problem started was when the device froze up (I left it alone for over an hour, but there was no change).
I then had to pull the battery. After I put the battery back into the T5355 it just keeps getting stuck on the "TOUCH Diamond2" screen.
I tried all the hard reset and soft reset tricks I could find and have no been able to either setting it back to factory or bootloader mode.
I was able to find a post that described how to place the boo.ini, flash.bin, and loader.bin file onto my micro sd card. I was able to to get the boot.ini an flash.bin files, but can't seem to find a loader.bin file (it that the actual OS rom?). I then found a post that showed how to use HiSilicon IDT to force the install of the OS Bin file (C02_HTC_20091102_R2127_英全视角B包.bin).
I followed the instructions on placing the T5355 into "Download" mode and pushing the OS bin fine to it.
I am able get the IDT software to detect the T5355 and start pushing the install, but the damned thing ends up giving an XLDR error.
PLEASE! PLEASE! Somebody help me! This phone is brand new and really want to get it working again.
Model: HTC(?) T5355
Please help me someone!!
Is there anyone out there that can help me???
I am so frustrated and can think of what else to do!
The biggest problem I have is that I can't use ActiveSync. If I could use that I wouldn't have much trouble.
Does anyone know how to use HiSilicon's IDT properly? The instructions I was working off of are in Russian. I think that a need a loader.bin file for the T5355 that I can put on my micro sd card...or maybe not...I don't know.
I just really want to get this device back to factory settings.
Please someone take pity on me!!!
enter bootloader [those orizontal strange colors]
try flashing a new rom. you may search and download the original 6.5 build from HTC
to enter bootloader, press "volume down + shutdown button" and then flash the rom
ATENTION: plug the USB cable, wait a few seconds, you should see USB on the lowest white color, then do the flashing job
I don't think you would be experiencing these problems with an original topaz
Please take care this is a HTC CLONE
Pisca said:
Please take care this is a HTC CLONE
Click to expand...
Click to collapse
oups, I'm high resolution on monitor, I thought it was saying "done" not "clone" ) ... there's a thread dedicated to china clones, look here http://forum.xda-developers.com/showthread.php?t=619643
run with a rom in bootloader, it shud work
enter bootloader [those orizontal strange colors]
try flashing a new rom. you may search and download the original 6.5 build from HTC
to enter bootloader, press "volume down + shutdown button" and then flash the rom
ATENTION: plug the USB cable, wait a few seconds, you should see USB on the lowest white color, then do the flashing job
Click to expand...
Click to collapse
DalvuS, thanks for the reply, but the issue is that I can't seem to get into bootloader mode . I wish I could. The T5355 seems to be stuck in the middle of wm 6.1 install. I need to somehow wipe the install and be able to push a reinstall back to the device.
I don't think you would be experiencing these problems with an original topaz
Click to expand...
Click to collapse
Exca that comment doesn't help me. It just makes me more sad. I was gipped when I bought the phone . I thought I paid for a "real" Diamond 2.
If you can't to catch the bootmode, looks like hardware problem.
You can't to repair it at home, imho. Try the specialized service.
..............
... and: are you sure about key combination for bootloader screen for CLONE?
Hello people, how can i dump my rom from my phone (mfu w71) for backup, because i cannot find any rom in english only in chinese. I started to dump the chinese rom with some chinese kitchen (K3系列ROM工具), but i'm stuck. I do not know to do anymore i have extracted ROM, SYS folder. I think it would be good to start another section on this forum for the chinese phones.
Some help from experienced cookers would me be much apreciated.
My T5355 is up and working!!!
Thanks to everyone who replied to my post!!!
I discovered that the problem was that the PC I was attempting the install from was running an AMD based processor.
I tried on the family laptop (which runs an Intel processor) and the install worked!
I AM SOOOO HAPPY!!!
b0gdi good luck with your issue. Try doing a search here in XDA for "dump my phone".
nothing[switched off] -> press start -> command -> bootloader -> bootloader commands -> system start -> play
checking one by one by interfering would have done the trick
I'm glad to hear that... so now you're ok
NEXT !
help me please
i Have Flash my phone 100 times with IDT for WM6.5 and WM6.1 all the versions my phone is T5355 Hot D2 but in one day i flash a rom that kill my phone the phone are conntinue to work but no screen picture only light i have try some russian Rom that kill my phone
the phone was been on guerant so i send him back to my supplier thay fix the phone but the factory said that thay need to change the screen so now thay really change the screen and the phone back to me with WM6.1 some New version 20.1.2010 some think like this i have made a call but the phone hang up and not make calls so i try to put him Back the WM6.5 English ROM that i use with this phone before i try to Flash Russian ROM that brake me the picture of the phone and block me the Bootloader Combination of SEnd+End+Power so that way i send him to repair .
so i try the English Rom that i have use before he DOwnload the Flash Fine but now the screen are stop to show picture But the Bootloader are work fine
so i try all the Roms that i have and all the same the screen dont want to show picture
some body have a same problem or can help me with this ?