Diamond Bluetooth connect problems with Parrot MK6000 - Touch Diamond, MDA Compact IV General

Hi
If anybody can help I will me much obliged.
I have just fitted a Parrot MK6000 bluetooth car kit, it seems to work OK except for the following issues.
1 - When I key on the ignition the Parrot automatically connects with the Touch Diamond, and then about a minute later it connects again.
2 - Sometimes after a phone call the Parrot seems to keep the car stereo in mute mode too long, sometimes 3 or 4 minutes.
3 - Sometimes after a phone call the Parrot reconnects again to the Touch Diamond even though it was previously connected.
Any Parrot users will know everytime it connects it plays a loud drum like tone over the speakers, which is annoying to say the least when it insists on keeping doing it.
I have updated the Parrot firmware to the latest 1.03 version.
Is there something within the Touch Diamond that i can change to prevent these issues, I was thinking maybe some registry settings for the bluetooth setting.
I have tried every combination of bluetooth settings in the standard HTC menus.
Anybody had the same or similar issues and found a way of fixing it ?
I have tried searching the Parrot website and other than firmware update have not found anything useful.
Quite happy to change ROMs or Radios is any user knows a combination that works without these issues.
Thanks

I had some problems with my carkit and I tried this software and it fixed them. My problems where different but this program adds a bluetooth profile for better handling. Give it a try; use the trial. It is for 30 days and see if it is worth purchasing,
http://www.jetwaremobile.com/
Good luck.

Thanks for the suggestion.
However I tried it and it did not make any difference.
Still looking for the fix if anybody else has suggestions.

Related

Bluetooth Stack problem on Kaiser - automatically re-establishing pair

Hi all,
I have posted this question also over a 4winmobile as I cant access xda-dev from work. Hopefully someone here can help.
I've been having difficulty with my Kaiser and a Parrot MK6000 car kit. I have tested the carkit with a Nokia as well, and have some results to report to aid in troubleshooting.
The Nokia was paired with the Parrot MK6000 kit, answers and makes calls and streams audio no problem. When the car is turned off, the pairing ends, when the car is started again the pairing starts back up ... auto, no probs. In addition, if you make a call with the phone, at the end of the call the pairing is ended, but within a few seconds is re-established.
On my Kaiser, I can pair the phone and car kit, but if the connection is lost (ie the car is turned off or bluetooth is stopped on the phone) and then I turn the car back on, it will not automatically pair. It attempts to, the car kit mutes the car radio and plays a tone, but the pairing is not established by the phone. It continues to do this every 30 seconds or so, but does not establish a connection.
Also, if I make a call with the phone when it has been sucessfully paired, on ending the call, the phone will not re-establish the pairing.
My conclusion is that all of my troubles relate to the fact that the pairing will not re-establish once lost.
Is anyone able to assist? I have upgraded the Kaiser radio to 1.27.12.32 (yes ... just tonite, see http://forum.xda-developers.com/showthread.php?t=349528&page=2) but have also tried radio roms 1.27.12.11 and 1.27.12.17 with no success. The ROM version is 1.81.861.0. Ive also tried installing some of the BT stacks that were developed up for the Hermes with no success. I've also installed Jetware with no sucess.
Getting very frustrated!
Adam
adamcullen said:
Hi all,
I have posted this question also over a 4winmobile as I cant access xda-dev from work. Hopefully someone here can help.
I've been having difficulty with my Kaiser and a Parrot MK6000 car kit. I have tested the carkit with a Nokia as well, and have some results to report to aid in troubleshooting.
The Nokia was paired with the Parrot MK6000 kit, answers and makes calls and streams audio no problem. When the car is turned off, the pairing ends, when the car is started again the pairing starts back up ... auto, no probs. In addition, if you make a call with the phone, at the end of the call the pairing is ended, but within a few seconds is re-established.
On my Kaiser, I can pair the phone and car kit, but if the connection is lost (ie the car is turned off or bluetooth is stopped on the phone) and then I turn the car back on, it will not automatically pair. It attempts to, the car kit mutes the car radio and plays a tone, but the pairing is not established by the phone. It continues to do this every 30 seconds or so, but does not establish a connection.
Also, if I make a call with the phone when it has been sucessfully paired, on ending the call, the phone will not re-establish the pairing.
My conclusion is that all of my troubles relate to the fact that the pairing will not re-establish once lost.
Is anyone able to assist? I have upgraded the Kaiser radio to 1.27.12.32 (yes ... just tonite, see http://forum.xda-developers.com/showthread.php?t=349528&page=2) but have also tried radio roms 1.27.12.11 and 1.27.12.17 with no success. The ROM version is 1.81.861.0. Ive also tried installing some of the BT stacks that were developed up for the Hermes with no success. I've also installed Jetware with no sucess.
Getting very frustrated!
Adam
Click to expand...
Click to collapse
Have you tried these registry tweaks? http://msdn2.microsoft.com/en-us/library/aa915920.aspx
There is a know problem with the Parrot kit and you will find a thread in this forum where a member has contacted Parrrot who replied that they are addressing the issue.
This one my be usefull.
http://forum.xda-developers.com/showthread.php?t=340908&highlight=parrot
NuShrike said:
Have you tried these registry tweaks? http://msdn2.microsoft.com/en-us/library/aa915920.aspx
Click to expand...
Click to collapse
Hi, thanks for that pointer ... most of what is described in that MSDN library isn't in my registry.
Im going to manually insert them all and see what happens.
A
Still no luck
I tried updating the Reg with the tweeks as suggest ... but still no luck. All i get is still the initial pair, but on disconnection, no automatic re-pairing of the device to the car kit.
Im doomed at this stage.
You're not alone. I have the same problem with my Motorola S9 headphones and Microsoft SYNC in my 2008 Ford Edge. Sometimes I have to turn BT on and off a couple of times for it to connect.
agreed
Turning the BT on and off a few times has also be part of my "solution" package.
This really isn't acceptable though. This device should automatically pair up, just like every other BT device does. BT is a protocol that should be adhered to and just work.
I have also tried this on my other WM device. It pairs a little better, but is not great. I've tried compairing the registry values of that device to my Kaiser, but I just dont understand the functionality of the reg settings enough to work out what to change.
Is there some developer out there who can help? This type of problem was experienced by us all back in the early days of the Hermes and this community sorted it out.
Can any developer out there help, like working out a port of the Widcomm BT stack for Kaiser?
a
Interesting. I have a Nokia CK-7W bluetooth car kit and the Tyn II has re-connected/connected to the kit every time. Actually more reliable than my SE K800i. Sorry that it doesn't help you.
Hey Juzzman,
nah, that doesnt help ... but does increase the frustration level!
Seems like you need to have a Nokia component in there somewhere for it to work ;-)
Anyhow, Im still convinced it is a bluetooth stack problem in the Kaiser. I'm going to try flashing one of the AT&T based roms and the other radio version and see what happens.
Cheers
Adam
I've had BT issues with all of my HTC devices, it's very frustrating.
Currently I've got a Kaiser (Orange), E650 (Orange) and a new S730, none of which work on my Pioneer headunit without Jetware.
The Kaiser with Jetware pairs up ok, but the sound is really tinny.
The E650 with Jetware sounds fine, but I can only send 150 contacts to the headunit.
The S730 doesn't pair, haven't put Jetware on it yet.
In the past I've had BT issues with M3100, C600, C500 etc etc.
Why the hell doesn't MS sort out their bloody BT stack!!!
Bluetooth problems
I am having the same problem with my JVC bluetooth unit BT1000. It will pair ok first time, allows me to make 2 calls. Will not the reestablish a connection/pairing. JVC worked fine with my sony erricson and nokia phones. Anyone found a cure to this?
Same problem with the stock AT&T rom (1.27.12.11) with the H700 headset.
Turn bluetooth on it normally sees the headset. If not turn it off and on again to get it to work. Once working it normal looses the connection after an hour or so.
Could it be a BT 2.0 Compliant issue?
I have posted this same problem earlier in xda-deveopers, on htc wiki and aximsite. Many people have viewed and are experiencing this same problem, but no one has posted any solution specific to my problem either. I hope a developer can solve this one for us. Is it a BT stack problem, or a BT 2.0 compliant problem, or a need for an updated ATT ROM to solve this issue? (I currently am using the stock ATT ROM 1.57.. that shipped with my Tilt.)
When I use my Motorola H700 with the Tilt the BT works fine, UNTIL, I use the voice speed dialing from the Tilt. Once I use the voice speed dialing directly on the Tilt, the Motorola H700 will no longer connect. I have to do a soft reset or go through the pairing process again. Once I re-establish pairing again, the H700 will continue to work fine, UNTIL, I use the voice speed dialing on the Tilt. Then we're back to having to do a soft reset to again establish H700 connection with the Tilt.
NOW, I just received a call back from an HTC tech who told me the problem is likely due to the Motorola H700 being only BT 1.2 compliant. He recommended that I try the Motorola H12, which is BT 2.0 compliant, but he could not absolutely guarantee this would solve my problem.
Does anyone know for SURE that the Motorola H12, being BT 2.0 compliant, will solve my problem? Or is there another solution?
Note: I have tried MS Voice Command 1.6 (full version), but the above problem still occurs. I have also tried Jetware, but again, no go. I am not sure that there is going to be an updated AT&T ROM to solve this issue either.
Additional Note: I have also tried other BT devices, such as the Jawbone, and the Plantronics Voyager. All do exactly the same thing as above.
Anyone have any solution? If the Motorola H12 is the solution, that would be great...
Thanks in advance.
I'm having the same problem with my new carkit. Did anyone ever find a solution to this??

Bluetooth stops/crashes when connected to Car kit

Hi,
When my phone is connected to my car kit (Opel/Vauxhaul UHP) bluetooth sometimes stops randomly. I can turn bluetooth on again with the commmanager and everything is working again. But it can hapen again after a few minutes.
Does anyone have this problem to or even better a solution?
I allready tried all the different Radio Roms, but this didn't solve my problem.
Well with mine i have some hickus but it just happpends once a while.
Most irritating about Diamond and BT in my opinion is that wa have no equalizing for it. and the sound setup from the begining is horrible.
Asked here if anyone has a solution before but none replied.
But as far 2 your problem no. And i use a Pioneer system in my car.
Mauser.NET said:
Hi,
When my phone is connected to my car kit (Opel/Vauxhaul UHP) bluetooth sometimes stops randomly. I can turn bluetooth on again with the commmanager and everything is working again. But it can hapen again after a few minutes.
Does anyone have this problem to or even better a solution?
I allready tried all the different Radio Roms, but this didn't solve my problem.
Click to expand...
Click to collapse
HI
Same was happend with me (Opel), when my battery is low.
orsiga said:
HI
Same was happend with me (Opel), when my battery is low.
Click to expand...
Click to collapse
Mine is not low on battery, but I shall try it once connected to the cigarette lighter.
Nobody else has this kind of problems??
Mauser.NET said:
Mine is not low on battery, but I shall try it once connected to the cigarette lighter.
Nobody else has this kind of problems??
Click to expand...
Click to collapse
I've a JVC head and my bluetooth has no problem.
I have a Honda Accord with handsfree built in and I too am having problems. The phone and car both agree that a connection has been made but when i use it to either ring out or receive a call the radio mutes and when receiving the ringing tone sounds over the car speakers but I can`t hear the caller except on the phone which isn`t very useful. Would a ROM or radio upgrade help or is it just a compatibility problem
davemazo said:
I have a Honda Accord with handsfree built in and I too am having problems. The phone and car both agree that a connection has been made but when i use it to either ring out or receive a call the radio mutes and when receiving the ringing tone sounds over the car speakers but I can`t hear the caller except on the phone which isn`t very useful. Would a ROM or radio upgrade help or is it just a compatibility problem
Click to expand...
Click to collapse
I had this kind of problems also. Also syncing the phonebook gave me problems. You could try JETware, this solved almost all my problems, except now the bluetooth crashes
Mauser.NET said:
I had this kind of problems also. Also syncing the phonebook gave me problems. You could try JETware, this solved almost all my problems, except now the bluetooth crashes
Click to expand...
Click to collapse
Thanks Mauser. I tried Jetware as you suggest and I`m afraid it didn`t help in fact I think it crashed the handsfree system in the car like you. This is the final nail in the coffin for my Diamond. I just can`t get used to it so it`s off to Ebay with it.
davemazo said:
Thanks Mauser. I tried Jetware as you suggest and I`m afraid it didn`t help in fact I think it crashed the handsfree system in the car like you. This is the final nail in the coffin for my Diamond. I just can`t get used to it so it`s off to Ebay with it.
Click to expand...
Click to collapse
I'm sorry to hear that
I am very pleased with my Diamond... I would sooner put my car on eBay than my Diamond
Did you try to check almost everything on in the advanced settings of Jetware? I have also limited the phonebook sync to max 5 entries to debug and on the site of Jetware there wat a fix for Opel car kits.
Keeping my fingers crossed, but until now I haven't experienced any bluetooth crashes.
Mauser.NET said:
I'm sorry to hear that
I am very pleased with my Diamond... I would sooner put my car on eBay than my Diamond
Did you try to check almost everything on in the advanced settings of Jetware? I have also limited the phonebook sync to max 5 entries to debug and on the site of Jetware there wat a fix for Opel car kits.
Keeping my fingers crossed, but until now I haven't experienced any bluetooth crashes.
Click to expand...
Click to collapse
Thanks again Mauser. I tried various settings but without any success, I think the phone is just not compatible with the Honda. Having said that I don`t have much luck with bluetooth at all on the phone. More often than not It just won`t detect other bluetooth devices and when it does it won`t send or receive files so it`s time for it to go and I can go back to a trusty Nokia
Problems here with BT connection to car kit, too. I'm using the built-in car-kit of an Audi A4 (standard one not that with navigation, remote SIM, etc). I've noticed the following issues:
- when I try to make a call, the CD is cut off but NOTHING is heard in the car speakers UNTIL the other party answers the call (and then I start the conversation). No ringing tone, no nothing. I cannot hear the busy tone, or network failure/congestion tone and this is annoying since I have to keep an eye on the phone to see what's happening. I found myself checking the phone when, after calling someone, nothing happened and in fact I got a busy tone and the call ended.
- sometimes, when I receive a call, the CD stops playing but when I answer nothing is heard from the car speakers but only from the phone (as davemazo said also).
- when I receive a call, I hear in the car speakers a "standard" calling tone, not the ringtone I have assigned for that contact
I have to mention that with any Nokia I had before (and still have one as a second phone), these problems do not exist. I know there is a compatibility between Audi factory installed car-kits and Nokia, but BT is a standard and most of the functions should be supported despite the phone model/type. I've tried also with an iPhone and it's working great, as my Nokia do. I don't understand why it is like this with the Diamond. In fact, I think it is not related to Diamond itself...it's doing like this with ANY Windows Mobile device I've tried in the past (Orange C600, Samsung I600).
Are there any solutions for this? A CAB, a new BT radio, a software, anything?... I don't want to buy a new BT car-kit and try with different models until I find something compatible
Thank you for any info/tip
Rapier said:
Problems here with BT connection to car kit, too. I'm using the built-in car-kit of an Audi A4 (standard one not that with navigation, remote SIM, etc). I've noticed the following issues:
- when I try to make a call, the CD is cut off but NOTHING is heard in the car speakers UNTIL the other party answers the call (and then I start the conversation). No ringing tone, no nothing. I cannot hear the busy tone, or network failure/congestion tone and this is annoying since I have to keep an eye on the phone to see what's happening. I found myself checking the phone when, after calling someone, nothing happened and in fact I got a busy tone and the call ended.
- sometimes, when I receive a call, the CD stops playing but when I answer nothing is heard from the car speakers but only from the phone (as davemazo said also).
- when I receive a call, I hear in the car speakers a "standard" calling tone, not the ringtone I have assigned for that contact
I have to mention that with any Nokia I had before (and still have one as a second phone), these problems do not exist. I know there is a compatibility between Audi factory installed car-kits and Nokia, but BT is a standard and most of the functions should be supported despite the phone model/type. I've tried also with an iPhone and it's working great, as my Nokia do. I don't understand why it is like this with the Diamond. In fact, I think it is not related to Diamond itself...it's doing like this with ANY Windows Mobile device I've tried in the past (Orange C600, Samsung I600).
Are there any solutions for this? A CAB, a new BT radio, a software, anything?... I don't want to buy a new BT car-kit and try with different models until I find something compatible
Thank you for any info/tip
Click to expand...
Click to collapse
Hi Rapier,
I also had a SPV C500, MDA Compact, Qtek 8500, Samsung I600, HTC Touch Dual and now the Diamond. The only one which gave me no troubles was the SPV C500, but I think that was because this phone didn't support phonebook synchronization and had no network identification/signal strength over bluetooth.
After the SPV C500 it went wrong. First I noticed that after a hard reset it worked for a few days. Later (about 2 years later ) I found out that it was because the call history was going to long to sync over bluetooth.
Then I found Jetware in which you can limit syncing to any number of items. They even had a fix for the connection to my carkit.
Unit now... it works like a charm... but keep my fingers crossed
I don't know if your carkit is a Audi UHV, but I saw that they had a fix for that too! You have to just install Jetware and then run the fix-file from your phone. Good luck!!
P.S. I am in no kind related to Jetware, I just found out that it worked for me.
Yes, I have an Audi UHV 6634. Thank you for the info, I'll try that and post the results here. Though, my car-kit is not the advanced one and I don't have to sync anything with it (contacts or something else). It's most working as a plain hands-free device, no extra functions...speaking of which, I've noticed that on the phone is detected as "hands-free"...why not "car-kit" as I know a car-kit has other functionality as well? This is the "standard" BT device for any audio enhancements (even if it is a car-kit not a BT headset), or I have to activate something to be recognized as car-kit?
Mauser.NET said:
Jetware? I have also limited the phonebook sync to max 5 entries to debug
Click to expand...
Click to collapse
my Honda system doesn`t read the sim I can only dial out via handsfree using contacts i`ve entered into the Honda system otherwise I either have to read the number to the system and it will ring out (most of the time anyway) or make the call on the phone (illegally obviously) cancel the call and then say "redial" and the system makes the call. So uless I`m misunderstanding this setting I don`t think it will help me.
I`ve searched the Jetware website and I couldn`t find a fix for my Honda
UPDATE: So...I've downloaded it, install it on my Diamond (including the extension file for Audi UHV) and...no change. Everything as before with both issues. Disappointed, I've uninstalled Jetware then...surprise. AFTER uninstall, I can now hear through my car's speakers the ID ringtone Maybe some BT settings were altered and remained like this after uninstall, but I don't know why it didn't work when Jetware WAS installed...strange.
Anyway, many thanks...at least half of the problems are now solved and this only by install/uninstall a program...that's cool. I must now find a way to make the car kit ring when I make a call, this is still an issue.
P.S. I've seen that Diamond support Headset and Handsfree profiles...and when connected to my car kit is set as Handsfree. I suppose this is better than Headset...but still no ring out tone.
Rapier said:
UPDATE: So...I've downloaded it, install it on my Diamond (including the extension file for Audi UHV) and...no change. Everything as before with both issues. Disappointed, I've uninstalled Jetware then...surprise. AFTER uninstall, I can now hear through my car's speakers the ID ringtone Maybe some BT settings were altered and remained like this after uninstall, but I don't know why it didn't work when Jetware WAS installed...strange.
Anyway, many thanks...at least half of the problems are now solved and this only by install/uninstall a program...that's cool. I must now find a way to make the car kit ring when I make a call, this is still an issue.
P.S. I've seen that Diamond support Headset and Handsfree profiles...and when connected to my car kit is set as Handsfree. I suppose this is better than Headset...but still no ring out tone.
Click to expand...
Click to collapse
No thanx! I'm glad I could help
Mauser.NET said:
Hi Rapier,
I also had a SPV C500, MDA Compact, Qtek 8500, Samsung I600, HTC Touch Dual and now the Diamond. The only one which gave me no troubles was the SPV C500, but I think that was because this phone didn't support phonebook synchronization and had no network identification/signal strength over bluetooth.
After the SPV C500 it went wrong. First I noticed that after a hard reset it worked for a few days. Later (about 2 years later ) I found out that it was because the call history was going to long to sync over bluetooth.
Then I found Jetware in which you can limit syncing to any number of items. They even had a fix for the connection to my carkit.
Unit now... it works like a charm... but keep my fingers crossed
I don't know if your carkit is a Audi UHV, but I saw that they had a fix for that too! You have to just install Jetware and then run the fix-file from your phone. Good luck!!
P.S. I am in no kind related to Jetware, I just found out that it worked for me.
Click to expand...
Click to collapse
Hello,
I have a Mercedes car kit and facing the same issue as you: everything works perfectly for a few days when hard-resetting my device, even with my 500+ contacts (they are loaded in less than a minute), but after a few days/weeks I can't get to have my call history or contacts displayed in less than half an hour!
Yesterday I thought I'd just hard reset my device because I had this problem again, but unfortunately it didn't work!
Guess what I have done differently this time: yes, I backed up and restored my call history, which I hadn't done the previous times! So I guess it is indeed related to the call history, but I can't test for now!
I have installed JetWare and limited the call history to 5 numbers, I'll try this tonight and I'll keep you informed...
Hello,
So I have tested this yesterday (installed Jetware and limited the call history to 5 numbers), and now it works FLAWLESSLY! I can browse through my 500 contacts instantaneously when I pair my phone with my Mercedes car kit.
So, in my case it was also clearly the CALL HISTORY that was causing problems... A BIG BIG thanks to Mauser for pointing out this!
I'm also having problem connecting my Diamond to my Volvo S80. All the other functions work except that I could not hear the other party through my car stereo and I also could not diconnect the call with my car end key.
I'll try the Jetware and I'll report back later. Thanks for the pointer.
turt said:
A BIG BIG thanks to Mauser for pointing out this!
Click to expand...
Click to collapse
No thanx! ... glad I could help

Connecting to bluetooth car kit takes very long!

Hi,
my Diamond works ok with my Parrot bluetooth car kit. The only thing that is really anoying me, it takes veeeery long until the Diamond has established the connection to the car kit. I have to drive for several minutes! until the Diamond connects. Before I had a Sony Ericcson phone where I did not have this problem.
Any ideas? Is this just because the Diamond is a WM phone?? Or is there a way to improve this?
Thanks
I use my diamond with a Parrot CK3300 - not sure if that is the same as yours. I only use it for handsfree since I use the Diamond's own GPS receiver. I don't have this problem - it picks up and pairs within seconds.
Have you flashed the Parrot with the latest software? I found that improved performance considerably - automatic update of contacts, user name on screen rather than phone name etc.
I use the Parrot CK3100 and the pick is almost instant; I've barely got in the car and started it up and the Parrot has picked up my Diamond. It was just as quick on my Hermes device too.
I also have a CK3100 and here's somewhat the same problem.
It connects in a few seconds, and it's usable.
But the synchronisation takes forever.....
That doesn't bother me, becouse I'm quite long in my car when driving to work...
But:
The phonebook in my CK3100 starts with the numbers wich are saved on the SIMcard.
All my friends are saved on the internal memory of the TD.
So if i want to call 'Anouk': I press 'A' on the CK3100.
It starts with the 'A' from the SIMcard.
Then I have to use the turning wheel, to scroll BACKwards to "anouk'!
So this takes a lot of time.... and is very, very unpracticle.
Someone a solution for this?
As I said before flashing the latest software onto my Parrot made it much better for syncing contacts. But I only need do it once - after that it only checks for changes. It should not be syncing each time because the Parrot should store the contacts itself.
Yep, just check the Parrot website to see what the latest update is for your particular BT device and try applying it. Saying that, I've not updated my one from factory.
Unfortunately I was not able to update my Parrot so far. I have only a CK3000 Evolution, Firmware version 5.08C. I guess I would need this special serial flash cable...
@ swissly
i have the same problems fw months ago. you have to delete the partnership's on your CK3000. press the red and the green button for more the 3 sec. (Erasing in progress) if this is done you can create a new partnership. hope that helps.
\\yoshi
swissly said:
Hi,
my Diamond works ok with my Parrot bluetooth car kit. The only thing that is really anoying me, it takes veeeery long until the Diamond has established the connection to the car kit. I have to drive for several minutes! until the Diamond connects. Before I had a Sony Ericcson phone where I did not have this problem.
Any ideas? Is this just because the Diamond is a WM phone?? Or is there a way to improve this?
Thanks
Click to expand...
Click to collapse
Hello
For all of you who have a Parrot Bluetooth car kit listen up:
When you use any phone with any Parrot Bluetooth car kits please go to the Parrot support website to flash your car kit - http://www.parrot.com/uk/support/onlinehelpguides
This will update the device with the latest firmware and as Parrot continuly add new phones to their list it is must. I did it as soon as my HTC Diamond arrived and finds it pairs/syncs within 1 - 3 seconds of switching the car on. FYI I have a Parrot MK6100 device, which supports A2DP Bluetooth audio and is mint. Previous to this I had an SPV M700 and a Parrot CK3100-something, but same thing - update it and you will find it solves the problem(s).
- PLEASE HOWEVER READ THE INSTRUCTIONS ON FLASHING - IT AIN'T HARD BUT READ IT ANYWAY!!! -
Please correct me if I'm wrong, but I still think I CANNOT UPDATE my Parrot CK3000 Evolution WITHOUT THE PARROT SERIAL CABLE!
swissly said:
Please correct me if I'm wrong, but I still think I CANNOT UPDATE my Parrot CK3000 Evolution WITHOUT THE PARROT SERIAL CABLE!
Click to expand...
Click to collapse
You are correct AFAIK. Most other Parrots can be updated easily using bluetooth, but not that one. Probably why it was cheaper than the others.

[Q] Bluetooth Carkit Issues :(

Please only repond to this if you have solved carkit issues.
I have a JVC AVX33 headunit with bluetooth, worked perfect on my old SE K800i, however on my diamond it keeps "booting" the bluetooth connection.
Connects for 30 seconds, looses connection, and connects again.
Is there a possible fix for this?
New Bluetooth Stack?
Tweak?
Or an explanation to why this is happening?
It Renders my Diamond useless in my car setup, and this would meen the world to me to have fixed.
Would purchasing a PARROT bluetooth carkit solve the problem?
Do you search the carkit with the phone or vice versa let the carkit search the phone?
I would recommend to test both setups. Do not forget to make your phone visible for the carkit when you want to pair it. Are you able to enter the bluetooth pair code on the phone when requested?
Hi, i have a Pioneer deh-p9800bt with bluetooth handsfree function and the only way to use it with wm6 and 6.1 (Htc Jamin, Gsmart i120 and Gsmart T600) has been to install Jetware HandsFree Extension. With the Gsmarts the Pioneer connects automatically and all works perfectly, with the Diamond the connection must be started every time from the Pioneer, but, then, all works (also battery and signal level): i think that a registry tweak has to be made in order to have an automatic connection.. i will try to see the differences between the registry settings of the i120 and the Diamond..
Yes i tried pairing both ways phone -> headunit and visa versa, and i am able to pair the two devices with code. However it keeps booting the bluetooth, looses connection and then getting it again. About every 30 seconds.
And i tried JETware yesterday without any change, however i am going through the different JETware config add-ons today to see if the result is better.
I think that its when the phone is trying to update the contact list to the headunit, it crashes the bluetooth. Anybody know if it is possible to change the bluetooth stack driver with another? on the HTC Touch Dual i had previous the bluetooth worked just fine.
bump bump bump

Diamond and car audionavigation JVC NX7000 bluetooth problem

Hi all,
Need help with my HTC Diamond. As my Pioneer car navigation, with which the diamond bluetooth functioned well, was stolen, I was advised to mount a JVC navigation system NX7000 with a detachable front in order to prevent theft. However, the HTC bluetooth dysfunctions. It connects and pairs without problems, but when the diamond goes into sleep or is switched off, it is impossible to establish a phonecall using the JVC car-unit, although it indicates that blueconnection is still valid. When I switch on the phone, even minutes later, it will eventually do the call. If I force the HTC to remain powered-on it will function normally. I am sure that this has something to do with a suspend-mode of the diamond bluetooth part and that this can be solved by the right registry tweak. I tried several tweaks that I found on the forum already but without succes. I upgraded the HTC to the latest firmware 2.03 but no improvement.
I called with HTC and they said that they know the correct registrysettings but they won't supply them because of "licence restrictions"...........
Anybody the same problem? Somebody who has the solution?
Thanks
I have exactly the same problem! Incoming calls work fine, but like you, I cannot initiate outgoing calls from the JVC unit unless the diamond is turned on fully. I there's not a fix for this, I may have to go out and buy an iphone again after selling mine to get a diamond!
there is a fix but HTC won't tell. they suggested to open a thread on this forum in order to get suggestions on the matter. and so I did. When I subsequently asked them if they would post this solution on this forum they said they would not :-(
Bluetooth problems across the board with JVC NX7000
drpellypo said:
I have exactly the same problem! Incoming calls work fine, but like you, I cannot initiate outgoing calls from the JVC unit unless the diamond is turned on fully. I there's not a fix for this, I may have to go out and buy an iphone again after selling mine to get a diamond!
Click to expand...
Click to collapse
You may not want to fall back on an iPhone with the JVC NX7000. Not to go too far off-topic here, but pairing an single iPhone works great (once I figured out the overly complicated menus). BUT...it won't let me pair a second phone (of any kind). Once the first phone is paired, all pairing menu options are greyed out ("Search" and "Open"), thereby preventing any further phones from being paired. I first need to unpair the first phone before I can pair the second one. JVC Support is comically unhelpful.
Has anyone had luck paring more than 1 phone (of any brand) with the JVC NX7000?
You are the lucky one! You can succesfully pair one phone but it works
I don't care if I can only pair one phone. I only have one phone! lol.
Hey guys!
kind of the same problem here but with the Volvo built-in bluetooth solution. Actually when the device sleeps and I initiate a call it will take some time, then the device will turn on and it will begin to dial but drops immediately. When the device is fully turned on there is no problem at all. Incoming calls work just fine. Even though it first rings on the phone and after a second or two it will ring in the car and the device will stop ringing. Which confirms that bluetooth sleeps somehow and only connects fully when the device is fully awake.
It really looks like bluetooth goes to sleep, so we need a solution which keeps bluetooth awake even if the device itself is in sleep mode.
Patrick
Exactly the problem I described. It's a sleep or suspend mode of the bluetooth that causes the dysfunction. I can pair nokias wih JVC without any functional problem, they work like a charm. It is really a HTC related problem, I tried a lot of registry tweaks suggested for similar problems in other HTC devices, but no luck so far.
Reply to Guitartng:
storing multiple bluetoothdevices in the JVC for subsequent use can be done by selecting "new device" and then go to "bluetooth setup".
Exact same issue with a Kenwood DNX 8120 double din unit.
If anyone finds out the solution, please post it here. I'll keep searching.
Good News Lads!
Well after blowing my head of trying different roms and radios got a solution.
The solution comes from JVC stereo and not from Htc diamond Phone!
You have to set special phones To Samsung E520 and then pair device with the htc diamond. It works like a charm, know I can make calls through my JVC stereo and NO MORE deep sleep of htc diamond.
Try with samsung, it work for me, if not try with other phones in special phones before pairing!
Cheers!
I just wanted to let you know that I also was able to fix my bluetooth issue by flashing stock firmware 2.03.405.3 WWE with Radio 1.09.25.23. I was previously using Dutty's V4 which is based on 2.03 afaik, but it look like Dutty tweaked something on the bluetooth stby behaviour.
Anyway, it works like a charm now and the whole calling and answering process is also much faster!

Categories

Resources