Related
I am trying to install a rom to my wing from over 3 days couldn't do it , I need to know where to put the files and how to set the files up , This maybe easy for you but not for average person like me , Please help.
reply
sorry i dont have a answer for you.but, i feel your pain i am going through this same stuff and i is pissing me off. i had my friend do everything but he is getting pissed off now because i keep calling him on ****. i need help too.
Well, we need to know what you are doing first!
What ROM are you flashing?
Do you have HardSPL already on? Or do you have no idea? haha
Thanks for your respond , I will like to install ROM HERALD WWE 6.1 BUILD 20764.1.4.3 (Blue clear) , I have no idea what is HardSL !! but i will learn if you give me a little direction .
tazzam72 said:
Thanks for your respond , I will like to install ROM HERALD WWE 6.1 BUILD 20764.1.4.3 (Blue clear) , I have no idea what is HardSL !! but i will learn if you give me a little direction .
Click to expand...
Click to collapse
How to Flash HardSPL
1) Find out your IPL
-- Do a Soft Reset (Push Button under volume w/Stylus)
-- While doing Reset, hold the Camera button, it should bring up the Bootloader menu and list your IPL (I think, it has been a while since I haven't been running HardSPL)
2) Verify your IPL is 4.xxx or Higher!
3) Boot your phone Again
4) BEFORE Hard-SPL--go to Settings->Connections->USB to PC and check that checkbox
5) Download HardSPL:
http://rapidshare.de/files/38148213/HardSpl_WM6.rar.html
6) Transfer these files to the phone:
--- a) install canonyang.cab
--- b) install aserpolicy.cab
--- c) install disablesecurity.cab
7) Soft Reset again
8) Run ROMUpdateUtility.exe
9) screen will become white - WAIT until it reboots itself (Should be like 10-15 min)
10) Phone will boot back to your main ROM
11) Soft Reset, Hold Camera button, check if SPL is 4.70.yang
Okay, now HardSPL is on
12) Download Your ROM
There are 2 ways of doing this now, either
1) Run ROMUpdateUtility.exe - When finished, go to Step 8.
-OR-
2) Put RUU_signed.nbh on your SD-Card and call it HERAIMG.nbh
3) Soft Reset, hold the Camera button
4) It will say: PRESS KEY TO INSTALL or something like that...
5) Press the volume button down or up
6) The ROM should begin to Extract/Install
7) When it finishes, do a Soft Reset
8) You should have your new ROM now!
Good Luck!
Original HardSPL Thread:
http://forum.xda-developers.com/showthread.php?t=358225
Thanks will try now
I followed the instructions, however when I turn on the phone holding down the camera button I get a white screen that states searching for SD Card (the white screen disappears quickly) then a new screen with RED, Green, Blue, White stripes with the IPL & SPL INFO, there is no option to press up to install the ROM. The ROM is in the Root of the Storage card named written as such in your walk through.
Tom in AZ said:
I followed the instructions, however when I turn on the phone holding down the camera button I get a white screen that states searching for SD Card (the white screen disappears quickly) then a new screen with RED, Green, Blue, White stripes with the IPL & SPL INFO, there is no option to press up to install the ROM. The ROM is in the Root of the Storage card named written as such in your walk through.
Click to expand...
Click to collapse
What size Card are you using?
I cannot get my 4GB or 8GB Card to flash... I have to use a 2GB card (I think it is SDHC Drivers not loading in BootLoader)
That is most likely your problem.
Try to get a hold of a smaller one (Maybe borrow one)
Fenopy said:
What size Card are you using?
I cannot get my 4GB or 8GB Card to flash... I have to use a 2GB card (I think it is SDHC Drivers not loading in BootLoader)
That is most likely your problem.
Try to get a hold of a smaller one (Maybe borrow one)
Click to expand...
Click to collapse
I had a 4gb in there, so that might be part of the problem, as time went on there was more going on it seemed. I finally got it to go back to that flash that came with the HardSPL software.
In order to do it, I started off by taking your advice. First I put in an older Lexar 2gb chip into the phone (Non-SDHC), then re-installed the three cabs that come with the hardSPL (installing them to the device, not the SD card). Then had to put the phone into the mode with the 4 different color bars (press and release the soft reset button while holding down the camera button till the bars showed), and finally I started the RUU from the PC since it still did not see or take the NBH file off of the root directory of the 2gb Micro SD.
I hope it does not get flippy like that again. The darn phone was deleting its own files as it was unhappy on the last build. Thanks for the tip on the SD swap. I'll be sure to keep that in my bag of tricks should it happen again.
Tom
where do i transfer the files to on the phone how do i install them
hankf said:
where do i transfer the files to on the phone how do i install them
Click to expand...
Click to collapse
HERAIMG.nbh go on the Root of the SD-Card.
All instructions are right in this thread:
http://forum.xda-developers.com/showpost.php?p=3321535&postcount=5
these files go to the root of the sd card: Transfer these files to the phone:
--- a) install canonyang.cab
--- b) install aserpolicy.cab
--- c) install disablesecurity.cab
Thanks for the help super n00b have been reading but still lost dont want to mess my phone up once I hard sl my phone can I still run my old rom or do I need to install a new rom right away
mmmm...
Damn Phone...
hankf said:
these files go to the root of the sd card: Transfer these files to the phone:
--- a) install canonyang.cab
--- b) install aserpolicy.cab
--- c) install disablesecurity.cab
Thanks for the help super n00b have been reading but still lost dont want to mess my phone up once I hard sl my phone can I still run my old rom or do I need to install a new rom right away
Click to expand...
Click to collapse
Those CABs can go anywhere. You need to put them somewhere (root of the SD works for simplicity)
So put the CABs on the root of the SD Card
Use File Explorer or Total Commander (Whichever you have on the phone) to navigate to your SD Card and run the 3 CAB files (Order does not matter) - Install them to the phone (Not the SD Card)
Then run the Installer from your PC as stated in the instructions.
*Note: Installing HardSPL will also install a New ROM (It is some old version of PDAViet I think)
As for installing your old ROM again, you would use a different method.
Similar to installing HardSPL, there is a PC-Based installer for the stock ROM, this ROM will revert you to T-Mobile default OS and back to SoftSPL.
I can upload this ROM later when I get home if you would like...
I think i got the CAB part understood.
When I do the HARDSPL I should have a ROM ready to install correct may I ask what you reccommend I have never used any of them so all new to me.
Could you please upload the stock rom to revert back to t-mobile, the installer and softSPL or what ever I need.
hankf said:
I think i got the CAB part understood.
When I do the HARDSPL I should have a ROM ready to install correct may I ask what you reccommend I have never used any of them so all new to me.
Could you please upload the stock rom to revert back to t-mobile, the installer and softSPL or what ever I need.
Click to expand...
Click to collapse
I would have the ROM you want ready, otherwise you would be stuck with the HardSPL ROM (Which you probably don't want to use)
I would suggest Just2Clean.
It is customizable & fast. (Can be found in the ROM Dev forum)
Stock ROM:
http://www.mediafire.com/?2nq9iu0a2nt
so with the stock rom I can go back to my t-mobile theme at any time or do I need to get rid of the HARDSLP first?
1 more question my phone is Windows Mobile 6 Pro so do I need to stick with wm6 rom or can I do like wm6.1
hankf said:
so with the stock rom I can go back to my t-mobile theme at any time or do I need to get rid of the HARDSLP first?
1 more question my phone is Windows Mobile 6 Pro so do I need to stick with wm6 rom or can I do like wm6.1
Click to expand...
Click to collapse
The Stock ROM installer puts SoftSPL back on the phone.
Windows Mobile 6.1 is just modified version of Windows Mobile 6.
It doesn't matter.
got the phone HARDSLP tried installing rom just2clean of the sd card having the same problems as in post #7 tried different size microchip 2gig with no luck so i installed touchFLO 2d and now my phone just keeps rebooting tried connect back to the pc but it sees no phone any ideas
hankf said:
got the phone HARDSLP tried installing rom just2clean of the sd card having the same problems as in post #7 tried different size microchip 2gig with no luck so i installed touchFLO 2d and now my phone just keeps rebooting tried connect back to the pc but it sees no phone any ideas
Click to expand...
Click to collapse
Try using Flash Center (http://rapidshare.com/files/202330180/Flash_Center.rar.html)
1) Put the phone in BootLoader (Make sure it says SPL 4.70.yang)
-- To get in BootLoader: Do a Soft Reset while holding down the Camera Button
2) Put the ROM in the 'RUU' folder (Name it anything [No spaces/special characters]) and try flashing using ROMUpdateUtility
If SPL is not 4.70.yang:
Try Re-Flashing HardSPL
If it won't stay connected long enough to flash (Gives an error upon flashing)
- When the Phone reboots itself, try holding the Camera button again, it sometimes will keep going
If you STILL can't get it going..
- Search desperately for a different SD Card (Make sure it is formatted in FAT32/FAT16)
When i turn on my phone I get the Tri Colored screeen
and it says: Upgrade ROM error code please try again.
and then the phone turns off and on.... Please help....
please please HELP SOMEONE!!!!
Don't dispair! I had the same problem and got out of the situation: http://forum.xda-developers.com/showthread.php?t=505377&p=3677341
You probably have the wrong Original Rom from HTC installed (may wrong language).
To solve the situation you will need USPL. USPL will install. If you are using Windows Vista you will probably have to update the drivers (See the thread).
Once USPL is running install the Original HTC 1.56-ROM.
but how can i can i installl uspl if every time i get into bootloader it turns off after 10 seconds and then turns back on...
nobody else can help??????
Try to take out the battery for one minute or two, then see what happens when switching on.
If ok (usual start) make usual normal bootloader state, and see what is your SPL. Then decide which flash you have to do.
Mr. Nick said:
but how can i can i installl uspl if every time i get into bootloader it turns off after 10 seconds and then turns back on...
Click to expand...
Click to collapse
Flash back your original ROM, you don't need USPL to do this.
For your original ROM look at this link:
http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Ship_exe
If you have problem flashing with you PC, you can try to flash from SD just extracting the files from the original ROM exe you downloaded on a temp folder (you can use winrar to do it), rename the "ruu_signed.nbh" to "BLACIMG.nbh", copy it to the root of your SD card, and flash the rom from the tri-color screen by pressing the power button.
Then, if everything is fine and your phone work again, you can think to flash a coocked ROM using USPL.
NOTE: you can read the wiki to learn something more, start here:
http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Flash1
please help me!!!!!
dalamario said:
Flash back your original ROM, you don't need USPL to do this.
For your original ROM look at this link:
http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Ship_exe
If you have problem flashing with you PC, you can try to flash from SD just extracting the files from the original ROM exe you downloaded on a temp folder (you can use winrar to do it), rename the "ruu_signed.nbh" to "BLACIMG.nbh", copy it to the root of your SD card, and flash the rom from the tri-color screen by pressing the power button.
Then, if everything is fine and your phone work again, you can think to flash a coocked ROM using USPL.
NOTE: you can read the wiki to learn something more, start here:
http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Flash1
Click to expand...
Click to collapse
sir you don't understand.... how can i flash back to my original ROM if it turns off every 10 seconds when i turn the phone on......
and also.... if i press the button on top... nothing happens.... if i put the usb cable into the phone it will go into the tri- color screen
Mr. Nick said:
sir you don't understand.... how can i flash back to my original ROM if it turns off every 10 seconds when i turn the phone on......
and also.... if i press the button on top... nothing happens.... if i put the usb cable into the phone it will go into the tri- color screen
Click to expand...
Click to collapse
It mean your phone stay at bootloader? tri-color sreen with SPL you can see. It's ok. You should download USPL 2.5 and Rom ship 1.56.4xx. Fisrt you flash SPL by running blac_uspl , your SPL will be change to 1.15USPL, then you flash ship rom 1.56.4xxx, then everything will be ok. Give it a try
Note : It's more stable if you use Win XP.
from my experience with HTC Wizard and what you are describing it
sounds like
your battery is very close to dead
you need to find a way to recharge it
your phone is protecting it by shutting off
also i don't know how valid this is for the Blackstone
but the wizard would not charge in tri-color mode
(again for battery sake)
so make sure you have a nicely charged battery (buy a spare or a table charger)
and then try to flash something again
P.S. i don't know how one sentence cries for help peppered with EXCLAMATION points encourage anyone to help you
nguyenbathanh said:
It mean your phone stay at bootloader? tri-color sreen with SPL you can see. It's ok. You should download USPL 2.5 and Rom ship 1.56.4xx. Fisrt you flash SPL by running blac_uspl , your SPL will be change to 1.15USPL, then you flash ship rom 1.56.4xxx, then everything will be ok. Give it a try
Note : It's more stable if you use Win XP.
Click to expand...
Click to collapse
A clarification of the above post. When you have 3 colors (actually 4 with white color) and USB on the white band you have to start blac_uspl.exe. That will replace the original bootloader of your phone with cracked temporary bootloader named USPL. At this stage it shall no more give errors and you may flash it from the PC or from the memory card.
The suggestion for the battery also seems fair.
Mr. Nick said:
sir you don't understand.... how can i flash back to my original ROM if it turns off every 10 seconds when i turn the phone on......
and also.... if i press the button on top... nothing happens.... if i put the usb cable into the phone it will go into the tri- color screen
Click to expand...
Click to collapse
You have to copy the BLACIMG.nbh on the microSD using a USB card reader, not your phone. Then with the microSD on the phone, in the tri-color screen, it will automatically flash your ROM, if you don't have low battery of course.
If you want to use USPL to flash a coocked ROM (for your original official rom is not needed). Your phone have to stay at tri-color screen for more then 10s.
Perhaps your problem is a low battery as someone already suggested.
Do you have tried to remove battery and put it back, let the phone off and charge it with the wall charger?
lol i did have low battery... how unlucky am i... it would shut off every so often....
but i fixed!!!!
i took out the battery and synced it with the cable..... without a battery inside and it worked!!!
I love you guys!!!!
i am not lieing i was about to cry
wow
Mr. Nick said:
lol i did have low battery... how unlucky am i... it would shut off every so often....
but i fixed!!!!
i took out the battery and synced it with the cable..... without a battery inside and it worked!!!
I love you guys!!!!
i am not lieing i was about to cry
Click to expand...
Click to collapse
LoL
Dont stress so much next time. When your stressed out you dont think with a clear head. Glad it worked out for you.
The changing of ROM only seems can not brick your phone. Only unsuccessful changing of SPL can. Until SPL is OK you may ever flash new ROM.
Hi! I have a question about roms. I want to flash my rom with let"s say shadowmans win 6.5, but i dont know how, because everyone is talking about hardspl and branded phones. I have i stock rom now (6.1) and i have hardspl preinstalled, does that mean that i can flash any rom i want or what? What is the quickest way to flash and what can u do if flashing fails? I need a quick giude for dummies. Thanks for all your help!
the easiest way to flash is with custom RUU it is explaind in hspl Wiki- as you will use this to flash hspl
download newest hspl 1.83 olinex and flash it
http://forum.xda-developers.com/showthread.php?t=520312
download ROM
connect you topaz to pc in active syns mode
open CustomRUU it us usually included with downloaded ROM
follow the instructions
then you can flash the radio again use the wiki
http://wiki.xda-developers.com/index.php?pagename=Topaz_Radio_ROM
hope this can get you started
If you definitely have hspl 1.83 olinex installed (you can check from the 3 colour bootloader screen - completely switch off your topaz and switch on again whilst holding volume down key), then you can flash any ROM using just your microsd card instead of connecting to your PC.
Download the ROM of your choice and extract the .nbh file from the archive or folder. It will be the biggest file in the archive. Rename this to TOPAIMG.nbh and put it in the root (top level) of your microSD card.
Make sure your battery is near to full, then turn off and restart your Topaz in bootloader mode as described above. It will detect the ROM and ask you to confirm upgrade. Simple as that. When it's complete and says "success" you can restart your phone using the reset button.
If ever it fails, you can simply do it again. Or, take out your microSD, put it in a card reader and put another TOPAIMG ROM file there, re-insert, and reflash.
Don't forget to delete the TOPAIMG file afterwards.
You can flash complete ROMs this way or just radio ROMs, it's the same process. I like this method because it's self-contained and doesn't rely on connection to your PC. Only make sure a) olinex 1.83 is installed already, and b) there's adequate battery left.
Don't forget to make a note of your stock ROM so that you can download it again in case you ever want to go back to it, or if you send your phone in for service.
problem
I did what you said but when I turn on the power with volume down press i can read, for a very short while, the word "no file image". What I have to do now? In the micro SD there is only the .nbh file and in the boot mode I can read that olinex 1.83 is installed.Help please.thanks a lot. Simon
I have checked that too, but i have hspl 1.33, does that mean i can flash any rom i want from my sd card or i must have 1.83 to do that?
Thanks for help
tommaazz said:
I have checked that too, but i have hspl 1.33, does that mean i can flash any rom i want from my sd card or i must have 1.83 to do that?
Thanks for help
Click to expand...
Click to collapse
you want the latest hard spl 1.83 so that there wont be any problems. all the chefs state in there rom thread to have that one too.
fs1978 said:
I did what you said but when I turn on the power with volume down press i can read, for a very short while, the word "no file image". What I have to do now? In the micro SD there is only the .nbh file and in the boot mode I can read that olinex 1.83 is installed.Help please.thanks a lot. Simon
Click to expand...
Click to collapse
is your micro sd formatted with fat 32? must be formatted in order to flash a rom using a micro sd card first. you dont have to power down your device to flash from sd card either. just hold volume down and insert stylus in the soft reset hole. hold until bootloader screen comes up. after flashing a hard reset is recommended. thats when you power down the device. you have to wait till everything gets set up first though to get to where you can power down the device though. hold volume up and down button. while holding those buttons turn the power back on. then follow the instructions it says.
fs1978 said:
I did what you said but when I turn on the power with volume down press i can read, for a very short while, the word "no file image". What I have to do now? In the micro SD there is only the .nbh file and in the boot mode I can read that olinex 1.83 is installed.Help please.thanks a lot. Simon
Click to expand...
Click to collapse
Is your ROM file named exactly TOPAIMG.nbh? Note the caps for the filename and lower case for the extension.
I was just reading another thread and apparently this is important for the bootloader to recognise it.
Please add one small comment to HSPL instructions
Few of us get "stuck" installing HSPL... Once you see a tricolor screen you are to follow RUU...but it says to be connected in activesync. yet if one looks on activesync you see your device is disconnected.
Please add "wait a minute" and just click OK on RUU. By then it is connected just doesn't show in activesync. Flash and all should be good.
Andy
I haven't burned a new ROM yet but have been getting the pieces together
I have an AT&T Pure which comes stock with WinMo 6.5 and also comes with
a Stock HSPL 1.83 (I believe 1.83 is required for all 6.5 and above?)
I think there is a potential area of confusion here for Pure users
(Especially since the other Topaz came with WinMo 6.1 and HSPL 1.33)
there is an OEM HSPL 1.83 and an Olinex modified 1.83 that will unlock
the phone.
Correct me if I'm wrong but
The one that is actually needed is the "modified"
1.83 OliNex (available here on XDA from Olinex as a sticky)
Can someone confirm this "subtle" difference???
I've gone to the tri-color Boot screen and the stock Pure only says
HSPL 1.83 (it does does not say OliNex)
my current understanding is that I will need to
burn the Olinex HSPL over my Stock OEM 1.83
before adding a new ROM??
One final question is after I reburn the new Olinex HSPL
Do I need to install the new ROM at that point?
Or could I use my phone? (with old stock Rom plus new HSPL)
Just want know if I'd be "off the air" at that point or not?
(So maybe I'll wait with R1+ over the latest Dutty Rom)
TIA
Hope this can at least promote some understanding
KJL
problem
--------------------------------------------------------------------------------
I did what you said but when I turn on the power with volume down press i can read, for a very short while, the word "no file image". What I have to do now? In the micro SD there is only the .nbh file and in the boot mode I can read that olinex 1.83 is installed.Help please.thanks a lot. Simon
any idea on how to flash back to stock at&t rom for warranty purposes. i rmr seeing a post in the raphael rom section but nothing here. any ideas??? im turning this in for a tilt 2. sits perfectly in my car mount n looks like a micro mini netbook...haha....
Hi folks!
I hope that you can help me:
I have to restore the stock spl on my xperia in order to get the keyboard and a case crack repaired!
The initial situation was like this: X1 hard spled with custom fw.
I first downloaded a german vodafone rom and flashed this rom with the sd card method: Renamed the firmware to kovsimg.nbh, copied it to sd and flashed via hardspl. I rebooted the phone and the standard tom booted just fine.
Then I downloaded "ruusigned_072stockspl.zip" from this thread: http://forum.xda-developers.com/showthread.php?t=431218
I extracted it, renamed it to kovsimg.nbh and flashed it... after the flashing process (the bar was full which means it flashed 100% to me) the phone showed "loading" for a while... after like 10mins I put out the battery.
The phone now starts into tricolour screen even if I dont press power+down.
its on stock SPL (shows SPL-0.72.0000) and it says "Continue to Upgreade ROM... please wait" but nothing happens..
what steps should I take from there on? I ve attached a screen which shows the tri colour screen.
Did I brick my X1?
Don't think you got much more options then try to reflash the spl. Maybe that will fix this. Do you still got usb access in this tri color mode?
nope, I dont get a usb connection
With spl you mean I should try to reflash hardspl?
If I have no hard spl, is it possible to flash a original rom with a sd card only?
HellSassa69 said:
nope, I dont get a usb connection
With spl you mean I should try to reflash hardspl?
If I have no hard spl, is it possible to flash a original rom with a sd card only?
Click to expand...
Click to collapse
pls compare your problem with this post and see if the solution (under Edit) also applies for you
gl
DrakenKorin said:
pls compare your problem with this post and see if the solution (under Edit) also applies for you
gl
Click to expand...
Click to collapse
thx for your advice I am sure that this will be the solution - stupid thing is: like the guy in the post you linked I have lost my micro sd to SD Adapter and therefore I cant write the stock firmware to my card -.- stupid thing...
In a hour I ll rush away, buy a adapter and then try to flash the stock rom but as it sounds from the thread the scenario is the same so I think it will work.
EDIT: This was the solution I downloaded the stock rom from the sticky thread in the Rom Section from XDA, extracted it to the sd root and renamed it kovsimg.nbh. Put sd card into X1, started X1 which automatically booted into tri colour screen - I only had to press power to porcede and everything is finde now after the flashing process! Stock rom and stock spl on my X1 thanx
simple!
i had the same problem...just rename the original rom.image to RUU_Signed.nbh then open hardspl (dnt push next)and replace the file push next ,update and it;s done!don't worry if u see the error at 0 % try to open the x1 after that and it would be fine
My TP2 stopped working ((((((
I was using it with some cooked ROM (i think it's not relevant what exactly). This morning i had my breakfast and i've got an SMS from an acquaintance. After this i couldn't see my home screen anymore, but i could still use start menu and so on. I wasn't first time as this error happened, so i didn't thought anything and just made a reboot. After this i saw bootloader screen and it was message about missing ROM shortly to see. Nohting else, only bootscreen, hard reset didn't work either. So i came home, connected my phone via USB to my notebook, powered it on and started to flash ROM. As flash was successfully complete, the phone rebooted and i saw... bootloader again!
So i don't know what to do now, anybody some thoughts?
Djablos said:
My TP2 stopped working ((((((
I was using it with some cooked ROM (i think it's not relevant what exactly). This morning i had my breakfast and i've got an SMS from an acquaintance. After this i couldn't see my home screen anymore, but i could still use start menu and so on. I wasn't first time as this error happened, so i didn't thought anything and just made a reboot. After this i saw bootloader screen and it was message about missing ROM shortly to see. Nohting else, only bootscreen, hard reset didn't work either. So i came home, connected my phone via USB to my notebook, powered it on and started to flash ROM. As flash was successfully complete, the phone rebooted and i saw... bootloader again!
So i don't know what to do now, anybody some thoughts?
Click to expand...
Click to collapse
If you have a GSM TP2 try running Task 29 before flashing the ROM. http://forum.xda-developers.com/showthread.php?t=649191 After Task 29 then reflash your ROM of choice and then hard reset to make suer everything took.
Good luck
blutruck said:
If you have a GSM TP2 try running Task 29 before flashing the ROM. http://forum.xda-developers.com/showthread.php?t=649191 After Task 29 then reflash your ROM of choice and then hard reset to make suer everything took.
Good luck
Click to expand...
Click to collapse
Yes, i have a GSM TP2. As you advised, i downloaded Task 29, unzipped it and run ROMUpdateUtility.exe from its folder. After 100% phone booted again to the bootloader, I went to ROM's folder and run CustomRUU.exe from it to flash the new ROM. After "success" i disconnected the USB-cable and started the phone... no changes. I still see the bootloader. And i still cannot hard reset my phone for some reason.
Djablos said:
Yes, i have a GSM TP2. As you advised, i downloaded Task 29, unzipped it and run ROMUpdateUtility.exe from its folder. After 100% phone booted again to the bootloader, I went to ROM's folder and run CustomRUU.exe from it to flash the new ROM. After "success" i disconnected the USB-cable and started the phone... no changes. I still see the bootloader. And i still cannot hard reset my phone for some reason.
Click to expand...
Click to collapse
How are you hard resetting your phone? All I do is power it off then hold the send and end keys and press and hold the power button until a message pops up asking if you want to hard reset. Press the vol up key to reset and after it completes press the vol up key to reboot.
Just a random thought here--is it possible your volume down button is stuck?
blutruck said:
How are you hard resetting your phone? All I do is power it off then hold the send and end keys and press and hold the power button until a message pops up asking if you want to hard reset. Press the vol up key to reset and after it completes press the vol up key to reboot.
Click to expand...
Click to collapse
Yeah, I do the same. I hold the both outer keys and the power button but no message pops up, just the bootloader.
BigWopHH said:
Just a random thought here--is it possible your volume down button is stuck?
Click to expand...
Click to collapse
It might be possible, but if i press it, it feels like its OK. However, is there any method to test all the buttons of my phone?
Any other thoughts? Without phone i am totally f*cked up, cause i am not in my hometown right now and i have to keep contact with my business partners in there.
It sounds like your bootloader is somehow broken, if it isn't a problem with the volume down key.
Try searching for information about the "mtty" utility. It's kinda complicated, but I think it's helped people in a similar situation.
steviewevie said:
It sounds like your bootloader is somehow broken, if it isn't a problem with the volume down key.
Try searching for information about the "mtty" utility. It's kinda complicated, but I think it's helped people in a similar situation.
Click to expand...
Click to collapse
Thank's I'll inform myself about "mtty" keyword. But if u say that the bootloader could be broken, maybe i should try to reflash HardSPL or go back to stock SPL?
Djablos said:
Thank's I'll inform myself about "mtty" keyword. But if u say that the bootloader could be broken, maybe i should try to reflash HardSPL or go back to stock SPL?
Click to expand...
Click to collapse
Yes, that's another alternative, at least you can try it.
steviewevie said:
Yes, that's another alternative, at least you can try it.
Click to expand...
Click to collapse
Now I am encountering bigger problems with my device. I tried to use MTTY ver 1.42 first. I couldnt use it because there wasn't an option to choose USB-port. Yes, i unchecked "Connect via USB" in WMDC and killed it then in task manager. Then i flashed stock SPL ver 0.79, hm nothing new. Then I tried to flash the original SPL, i.e. ver 0.84 and it got stuck by 0%. I waited and waited and waited, so i had to remove cable and the battery. After that nothing worked. No flashing worked at all, even Task 29 gets stuck by 0% every time........ I dont know what to do now.....
Can you get into the bootloader still ?
steviewevie said:
Can you get into the bootloader still ?
Click to expand...
Click to collapse
Yes i do. I still see the bootloader showing me current SPL version (0.79 )
So does it still always go into the bootloader ? It won't boot ? If so, have you tried mtty to try and fix that ?
steviewevie said:
So does it still always go into the bootloader ? It won't boot ? If so, have you tried mtty to try and fix that ?
Click to expand...
Click to collapse
As i said above, i could not connect to the phone through mtty, but fortunately i have another laptop here with winxp on it so it works on it. I typed "set 16 0" and "task 8" and it booted again into the bootloader just like before.
Djablos said:
As i said above, i could not connect to the phone through mtty, but fortunately i have another laptop here with winxp on it so it works on it. I typed "set 16 0" and "task 8" and it booted again into the bootloader just like before.
Click to expand...
Click to collapse
Have you tried flashing a ROM using the storage card method? Might be some error being caused but your computer.
The following was taken from http://forum.xda-developers.com/showthread.php?t=550540
Flashing Via MicroSD Card
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the Rhodium Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to RHODIMG.nbh
4. Copy the RHODIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
You might also want to try flashing from another computer.
Djablos said:
Yes i do. I still see the bootloader showing me current SPL version (0.79 )
Click to expand...
Click to collapse
well it seems that you have flashed back to stock spl since it is showing you spl version (0.79)
which means you will have to hardspl it again in order to flash any custom roms again but it is probably unlikely that it will not work because when you reflash stock spl you are suppose to flash stock rom & radio first before flashing stock spl i'm just guessing i'm not to sure on this 1 i could be wrong though
P.S. - just a suggestion since you have stock spl back on the phone try & flash a stock rom to see if that works
Djablos said:
Yes i do. I still see the bootloader showing me current SPL version (0.79 )
Click to expand...
Click to collapse
Is that maybe the problem ? Did you flash the stock SPL back onto it as you referred to earlier ? Because 0.79 is a stock SPL version, so it won't boot a custom ROM with that SPL.
So is the whole problem that you have a custom ROM and stock SPL ? I hope it's that simple, but fear it isn't.
I hope!
Hello,
if you have 0.79 hard spl,
1. you should install stock rom, not cooked. After go to bootloader mode.
2. Run Rhodium-HardSPL_V2_00R3.exe from http://forum.xda-developers.com/showpost.php?p=4363807&postcount=1
3. Install cooked rom!
It is working!
I hope it will help your problem!
blutruck said:
Have you tried flashing a ROM using the storage card method? Might be some error being caused but your computer.
You might also want to try flashing from another computer.
Click to expand...
Click to collapse
Yeah guys, here's what i did and what i see. Before i flashed stock SPL 0.79 i flashed stock ROM and stock radio. Then i tried to flash stock SPL 0.84 and it didn't work for some reason. OK, then I read an advice from Doo Doo and tried to flash stock ROM again. I was wondering that it worked... but as it got 100% the device entered bootloader mode again! But after this the version of SPL was 0.88
I cannot use storage card method because i don't have any possibility to get access to the card from my PC And I just tried to hard SPL my phone from another PC (winxp) so it didn't work either, stuck by 0%.
Try to older stock rom. Maybe it will install older spl...
Sorry, but I couldn't help this problem! :S