Database Develop

HELP My P4350 is not responding!!:eek:

Can anyone help me, while updating my rom there went something wrong, i guess!
Now I only see the screen with 'Touch-IT' and I don't know what to do! Please help me!!
Thanks a lot! Bram

this guide really helped me when i started flashing
bramwillems said:
Can anyone help me, while updating my rom there went something wrong, i guess!
Now I only see the screen with 'Touch-IT' and I don't know what to do! Please help me!!
Thanks a lot! Bram
Click to expand...
Click to collapse
PAY SPECIAL ATTENTION TO STEPS 3. 3A,3B,3C...
1. Download which version of Touch IT you want. For the Last version made, here is the link: http://forum.xda-developers.com/showthread.php?t=340403
2. Backup any information you wouldn't want to lose. Either backup to memory card or PC; your choice
3. At this point, You need to install the official RUU for your device, if you're already running the official RUU, then you need to hard reset your device. (Press and hold both soft keys and press reset button, continue to hold softkeys til screen displays to hard reset. Press the call button to continue). If you need to install the official RUU, continue to step 3a4Here is a list of uploaded RUUs
3a. Enter bootloader on your phone (Hold camera button and press reset, continue holding camera until a screen with 3 gradient colors shows up
3b. Connect your computer via USB to your ppc (Pocket PC)
3c. Run the RUU .exe from your hard drive, follow its simple onscreen instructions and click check boxes necessary to continue with the installation. This should take a few minutes, and you will more then likely see your screen flash and change things, this is normal, let it work. After a few minutes it will boot up and go into "automatic customization of your device", I continued this (screen alignment, tips, auto setup), and waited for my device to be totally ready for me to use.
4. Connect your device via USB to the PC and wait for activesync. If it automatically pulls up a profile for your phones sync, delete that profile. If it asks again to setup device for syncing items, click cancel. You will still be able to explore your phone and install devices without setting up the sync profile for your phone.
5. Make sure your phone is connected as a guest, if it is not, make sure it is. The method I used to do this was this zip file I ran "guest only" registration entry. (Make sure and run allow partnership registration after completing installation), but it should display as guest after the hard reset.
6. Copy aserg policies.cab to your mobile device
7. Run aserg policies.cab from your device
8. Soft reset (use stylus for button on side of wing, or on bottom of herald)
9. Go into your comm manager on your phone, and disable "phone". Basically enter flight mode so nothing can be sent to your phone during this process.
10. Once booted, its time to give it a shot. Make sure you're still connected as guest, and run !Upgrade_rom.bat from Touch_it folder on your PC
11. This will bring up a command prompt waiting for you to hit a key to begin, press any key
12. During this time it is installing, NEVER touch your phone or play with it in any matter. It may look as though the command prompt has gotten hung up at times, but leave it run until it completes (or fails). your phone will pop up a message saying "unknown status" or the likes, but dont close that window, like I said just leave it alone.
13. If you have no error messages in the command dialogue box then you're ready to hard reset your phone. (press both softkeys, and press reset, continue holding softkeys til you see a dialogue asking if its okay to restore settings, hit the call button to finish it)
14. Your device SHOULD boot normally, go through setup, and you should be golden.
If at any time there is an error during install, but you still let it complete, you might have a chance at it working. Hard reset it after completion (even with errors) just to see if it works. If it wont go past your Tmobile or HTC picture screen on bootup, then you have bricked your device. To UNbrick it, run steps 3a through 3c and reinstall the RUU.
If you get any errors, try and try again. Its proven working on several devices.

thank you very much for your help, but i cant find the offical RUU?

bramwillems said:
thank you very much for your help, but i cant find the offical RUU?
Click to expand...
Click to collapse
You defenitifly flashed a rom from teh HARD-SPL RUU folder...
... or you left a SPL.nbh inside your RUU folder.....
All roms are found in my signiture "All roms"
And for better flashing... download latest TouchIT6.1.3 and replace the RUUsigned.nbh with a one you will flash.
Or flash the TouchIT 6.1.3
I know hardspl sorked for you.
If flashing isn´t working
PUT device in BOOTLOADER (cam + softreset) then it MUST work
Good luck

papamopps said:
You defenitifly flashed a rom from teh HARD-SPL RUU folder...
... or you left a SPL.nbh inside your RUU folder.....
All roms are found in my signiture "All roms"
And for better flashing... download latest TouchIT6.1.3 and replace the RUUsigned.nbh with a one you will flash.
Or flash the TouchIT 6.1.3
I know hardspl sorked for you.
If flashing isn´t working
PUT device in BOOTLOADER (cam + softreset) then it MUST work
Good luck
Click to expand...
Click to collapse
Thank you papamopps! I run the HARD-spl again and my phone is fully functional!
I was very afraid that I my phone was totaly crashed and I could thrown it away! Thank you for saving my dear phone

bramwillems said:
Thank you papamopps! I run the HARD-spl again and my phone is fully functional!
I was very afraid that I my phone was totaly crashed and I could thrown it away! Thank you for saving my dear phone
Click to expand...
Click to collapse
Since NOW - never use HArd-SPL again...
Take the RUU from TouchIT6.1.3 or any other official RUU WITHOUT SPL.nbh!!
and enjoy free flashing .....

papamopps said:
Since NOW - never use HArd-SPL again...
Take the RUU from TouchIT6.1.3 or any other official RUU WITHOUT SPL.nbh!!
and enjoy free flashing .....
Click to expand...
Click to collapse
But on the releases from Itje there is a note that is won't work without HARD-spl? So what is the difference? (I don't know if I ask stupid questions, forgive me)

If you have used hard-spl once on your phone, you dont need to do it again
I include in my rom releases what u need to flash
just run the rom.exe file, and the phone will update.

did i brick my blackstone??? PLEASE HELP!!!!

When i turn on my phone I get the Tri Colored screeen
and it says: Upgrade ROM error code please try again.
and then the phone turns off and on.... Please help....

please please HELP SOMEONE!!!!

Don't dispair! I had the same problem and got out of the situation: http://forum.xda-developers.com/showthread.php?t=505377&p=3677341
You probably have the wrong Original Rom from HTC installed (may wrong language).
To solve the situation you will need USPL. USPL will install. If you are using Windows Vista you will probably have to update the drivers (See the thread).
Once USPL is running install the Original HTC 1.56-ROM.

but how can i can i installl uspl if every time i get into bootloader it turns off after 10 seconds and then turns back on...

nobody else can help??????

Try to take out the battery for one minute or two, then see what happens when switching on.
If ok (usual start) make usual normal bootloader state, and see what is your SPL. Then decide which flash you have to do.

Mr. Nick said:
but how can i can i installl uspl if every time i get into bootloader it turns off after 10 seconds and then turns back on...
Click to expand...
Click to collapse
Flash back your original ROM, you don't need USPL to do this.
For your original ROM look at this link:
http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Ship_exe
If you have problem flashing with you PC, you can try to flash from SD just extracting the files from the original ROM exe you downloaded on a temp folder (you can use winrar to do it), rename the "ruu_signed.nbh" to "BLACIMG.nbh", copy it to the root of your SD card, and flash the rom from the tri-color screen by pressing the power button.
Then, if everything is fine and your phone work again, you can think to flash a coocked ROM using USPL.
NOTE: you can read the wiki to learn something more, start here:
http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Flash1

please help me!!!!!

dalamario said:
Flash back your original ROM, you don't need USPL to do this.
For your original ROM look at this link:
http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Ship_exe
If you have problem flashing with you PC, you can try to flash from SD just extracting the files from the original ROM exe you downloaded on a temp folder (you can use winrar to do it), rename the "ruu_signed.nbh" to "BLACIMG.nbh", copy it to the root of your SD card, and flash the rom from the tri-color screen by pressing the power button.
Then, if everything is fine and your phone work again, you can think to flash a coocked ROM using USPL.
NOTE: you can read the wiki to learn something more, start here:
http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Flash1
Click to expand...
Click to collapse
sir you don't understand.... how can i flash back to my original ROM if it turns off every 10 seconds when i turn the phone on......
and also.... if i press the button on top... nothing happens.... if i put the usb cable into the phone it will go into the tri- color screen

Mr. Nick said:
sir you don't understand.... how can i flash back to my original ROM if it turns off every 10 seconds when i turn the phone on......
and also.... if i press the button on top... nothing happens.... if i put the usb cable into the phone it will go into the tri- color screen
Click to expand...
Click to collapse
It mean your phone stay at bootloader? tri-color sreen with SPL you can see. It's ok. You should download USPL 2.5 and Rom ship 1.56.4xx. Fisrt you flash SPL by running blac_uspl , your SPL will be change to 1.15USPL, then you flash ship rom 1.56.4xxx, then everything will be ok. Give it a try
Note : It's more stable if you use Win XP.

from my experience with HTC Wizard and what you are describing it
sounds like
your battery is very close to dead
you need to find a way to recharge it
your phone is protecting it by shutting off
also i don't know how valid this is for the Blackstone
but the wizard would not charge in tri-color mode
(again for battery sake)
so make sure you have a nicely charged battery (buy a spare or a table charger)
and then try to flash something again
P.S. i don't know how one sentence cries for help peppered with EXCLAMATION points encourage anyone to help you

nguyenbathanh said:
It mean your phone stay at bootloader? tri-color sreen with SPL you can see. It's ok. You should download USPL 2.5 and Rom ship 1.56.4xx. Fisrt you flash SPL by running blac_uspl , your SPL will be change to 1.15USPL, then you flash ship rom 1.56.4xxx, then everything will be ok. Give it a try
Note : It's more stable if you use Win XP.
Click to expand...
Click to collapse
A clarification of the above post. When you have 3 colors (actually 4 with white color) and USB on the white band you have to start blac_uspl.exe. That will replace the original bootloader of your phone with cracked temporary bootloader named USPL. At this stage it shall no more give errors and you may flash it from the PC or from the memory card.
The suggestion for the battery also seems fair.

Mr. Nick said:
sir you don't understand.... how can i flash back to my original ROM if it turns off every 10 seconds when i turn the phone on......
and also.... if i press the button on top... nothing happens.... if i put the usb cable into the phone it will go into the tri- color screen
Click to expand...
Click to collapse
You have to copy the BLACIMG.nbh on the microSD using a USB card reader, not your phone. Then with the microSD on the phone, in the tri-color screen, it will automatically flash your ROM, if you don't have low battery of course.
If you want to use USPL to flash a coocked ROM (for your original official rom is not needed). Your phone have to stay at tri-color screen for more then 10s.
Perhaps your problem is a low battery as someone already suggested.
Do you have tried to remove battery and put it back, let the phone off and charge it with the wall charger?

lol i did have low battery... how unlucky am i... it would shut off every so often....
but i fixed!!!!
i took out the battery and synced it with the cable..... without a battery inside and it worked!!!
I love you guys!!!!
i am not lieing i was about to cry

wow
Mr. Nick said:
lol i did have low battery... how unlucky am i... it would shut off every so often....
but i fixed!!!!
i took out the battery and synced it with the cable..... without a battery inside and it worked!!!
I love you guys!!!!
i am not lieing i was about to cry
Click to expand...
Click to collapse
LoL
Dont stress so much next time. When your stressed out you dont think with a clear head. Glad it worked out for you.

The changing of ROM only seems can not brick your phone. Only unsuccessful changing of SPL can. Until SPL is OK you may ever flash new ROM.

Killed HD while flashing?

Hi there,
I had an original german Touch HD and updated it to 1.56 StockROM. So good so far ... then wanted to flash another ROM and flashed 1.56 Olinex HardSPL Wrapper. Worked as well. As it was not possible to flash the ROM I wanted (no USB connection with the bootloader) I wanted to go back and flashed the StockSPL. Unfortunately, this was the 1.14 Stock HardSPL and the flash worked as expexted
Now the HD boots with wrong colors and does not react to screen touches anymore. After a certain time a window comes up with a gwes.exe error message which should be sent to Microsoft.
I tried to Hardreset, but it does not work anymore with the hardwarekeys.
Active Sync does not connect anymore, so I can't access the device as I should to do something ... The system seems to run normally, but no interaction possible ...
Has anyone an idea what I could try? Is there a way to flash from SD card as on the touch diamond? Any autostart application on the SDcard, which causes a hardreset?
I look forward to your suggestions ...

hkr said:
Hi there,
I had an original german Touch HD and updated it to 1.56 StockROM. So good so far ... then wanted to flash another ROM and flashed 1.56 Olinex HardSPL Wrapper. Worked as well. As it was not possible to flash the ROM I wanted (no USB connection with the bootloader) I wanted to go back and flashed the StockSPL. Unfortunately, this was the 1.14 Stock HardSPL and the flash worked as expexted
No the HD boots with wrong colors and does not react to screen touches anymore. After a certain time a window comes up with a gwes.exe error message which should be sent to Microsoft.
I tried to Hardreset, but it does not work anymore with the hardwarekeys.
Active Sync does not work anymore, so I can't access the device as I should to do something ...
Has anyone an idea what I could try? Is there a way to flash from SD card as on the touch diamond? Any autostart application on the SDcard, which causes a hardreset?
I look forward to your suggestions ...
Click to expand...
Click to collapse
Take out the battery for 1-2 min. Then replace batt and hold down the volume down key and press the power on briefly while holding the volume down key. If you see a tri color screen you are ok. You can place a ROM on the SD card and flash from there doing the same above proceedure.

hkr said:
.....(no USB connection with the bootloader)...
Click to expand...
Click to collapse
take off the sd-card, than it should work

so then I could flash either an 1.14 StockROM or a 1.56 Stock HardSPL ...
I'lltry one of them, thanks for your help

bobsbbq said:
Take out the battery for 1-2 min. Then replace batt and hold down the volume down key and press the power on briefly while holding the volume down key. If you see a tri color screen you are ok. You can place a ROM on the SD card and flash from there doing the same above proceedure.
Click to expand...
Click to collapse
I feel better, the tricolor screen appears.
No I tried to flash 1.54 hardSPL and 1.56 official german Stock ROM. Both timers I get the message 'no image file!'
The RUU_signed.nbh is in the root of the 16GB SDcard.
Do I need to flash 1.14 Stock ROM, as I have 1.14 StockSPL installed?

Rename the RUU_signed.nbh to blacimg.nbh.
Always when flashing from SD-CARD you must rename the rom file
to blacimg.nbh
I hope it helps.

Thank you for your help, guys, it is up and running again

Good for you!

Bricked phone TyTN II....crap....what to do ?

Hey guys, i was flashing a new ROM and after i pressed Jump SPL on the phone , i didnt do HARD SPL but went on and installed a ROM ....well now it starts with the loading screen ...........and just never loads..... any suggestions ? is it trash ?? i hope not. Thank

mfesenko said:
Hey guys, i was flashing a new ROM and after i pressed Jump SPL on the phone , i didnt do HARD SPL but went on and installed a ROM ....well now it starts with the loading screen ...........and just never loads..... any suggestions ? is it trash ?? i hope not. Thank
Click to expand...
Click to collapse
Try flashing your stock ( original ) rom, found in the wiki . And start over again.
Oh yeah, and this time it might be a good idea to read ALL the instructions FIRST.

How ?? how can you do this with out Jump SPL ? its at the first initial screen with the name of the rom.... and thats it , connecting to my computer doesnt even make a connection sound......

denco7 said:
Try flashing your stock ( original ) rom, found in the wiki . And start over again.
Oh yeah, and this time it might be a good idea to read ALL the instructions FIRST.
Click to expand...
Click to collapse
How ?? how can you do this with out Jump SPL ? its at the first initial screen with the name of the rom.... and thats it , connecting to my computer doesnt even make a connection sound......

mfesenko said:
How ?? how can you do this with out Jump SPL ? its at the first initial screen with the name of the rom.... and thats it , connecting to my computer doesnt even make a connection sound......
Click to expand...
Click to collapse
Try to put your phone in bootloader. Press and hold camera button and power button, while pressing soft reset with stylus. Once in bootloader. Connect to PC and see if you can run the RUU in your stock rom.

denco7 said:
Try to put your phone in bootloader. Press and hold camera button and power button, while pressing soft reset with stylus. Once in bootloader. Connect to PC and see if you can run the RUU in your stock rom.
Click to expand...
Click to collapse
Nope, it just does a regular soft reset , and back to the same screen

it is easy to flash it back with original rom or unlock it. just read some tutos here on xda

JugglerLKR said:
it is easy to flash it back with original rom or unlock it. just read some tutos here on xda
Click to expand...
Click to collapse
i looked into it and they had solutions if your phone is in the tri colored screen. my phone is not. my phone is in the loading windows screen... but it never loads.

mfesenko said:
i looked into it and they had solutions if your phone is in the tri colored screen. my phone is not. my phone is in the loading windows screen... but it never loads.
Click to expand...
Click to collapse
that's even better - just start it in 3color boot loader and flash!
loading windows screen appears AFTER 3color boot loader...

mfesenko said:
Nope, it just does a regular soft reset , and back to the same screen
Click to expand...
Click to collapse
Keep trying to put it into bootloader. Try a hard reset and follow instructions to get it into bootloader. Sometimes it takes several tries.

JugglerLKR said:
that's even better - just start it in 3color boot loader and flash!
loading windows screen appears AFTER 3color boot loader...
Click to expand...
Click to collapse
Maybe, I didnt Explaine it correctly but , I do NOT get the tri colored screen . This is how it goes after i press the power button to start my phone : So it automaticaly goes into loading screen where on the bottom right hand corner it shows the Radio version , the G version and some other version.......... and that is the only screen i get after staring my phone.

Maybe you didnt read well enough..
Maybe, I didnt Explaine it correctly but , I do NOT get the tri colored screen . This is how it goes after i press the power button to start my phone : So it automaticaly goes into loading screen where on the bottom right hand corner it shows the Radio version , the G version and some other version.......... and that is the only screen i get after staring my phone
Click to expand...
Click to collapse
YOU AREN'T BEING ASKED TO HIT JUST THE POWER BUTTON
try to put your phone in bootloader. Press and hold camera button and power button, while pressing soft reset with stylus. Once in bootloader. Connect to pc and see if you can run the ruu in your stock rom.
Click to expand...
Click to collapse
keep trying to put it into bootloader. Try a hard reset and follow instructions to get it into bootloader. Sometimes it takes several tries.
Click to expand...
Click to collapse
THAT MEANS DO IT AGAIN !

Thanx
Thank you denco , for the info , and thanx chumley for beating some sence into me. So i got to the bootloader. Do i need to instal my original rom or can i just reinstall the one i got or maybe another one?

well I have the same problem.
It started with the edfc problem explained here
While trying to fix that problem, I switched my rom to the TPC elite rom series (windows 6.5).
All went fine till three days later, while text-messaging, the screen freezed. I removed the battery, restarted the device and found myself having the same symptoms discussed in this threat.
Putting my phone into bootloader doesn't work, and I think It has to do with the problem I had before; that apart from the directional buttons and the power button, all buttons are defunct.
Anyone any suggestions? (apart from: don't bother us, etc, etc...)

my phone randomly bricked too a while back....as far as I understand is that either you CAN put your phone in to bootloader or your phone is junked....correct me if im wrong ppl
.....make sure you hold the camera and power buttons then reset with stylus....
and make sure you install your stock rom...aka the att tilt rom

if you didn't do it already...
1. flash your original rom (SD card method - Step 5 Flashing Via MicroSD Card ) you need the rom to be at least from the same operator. it should run just fine, just as long as you follow the directions.
2. HardSPL,SIM CID unlock, etc. as described on the same forum i pointed to a little earlier. from this point on you should have a phone just like it was when new.
try to read more carefully (maybe a few times) and search before you start a new thread.
on the wiki and in the stickies in the rom development section you get a lot of "bricked" solutions. you just have to read them all and see what is your case...

Need help, X1 restart on logo

i have x1 restart on sony ericsson booting logo
i tried using task29 but always have error 262
then i try to flash using mmc it says completed 100% but my x1 stil restart on logo
is there any solution?

still no solution?

Have you tried a hard reset?

altae said:
Have you tried a hard reset?
Click to expand...
Click to collapse
do you mean hard reset (hold power + left + right button)?
i did, and on the screen shown test "this operation will delete all your bla..bla.."
but when resetting complete, it's still restart when booting and logo sonyericsson appears
is it hardware failure?

I would not give up yet. You say you have tried installing another rom to no avail? Is hard spl installed on your phone? What kind of rom do you use (WM 6.1, WM 6.5)?

looks like your rom is messed up and can't boot anymore.
error 262 means you haven't got hard-spl (needed for task29 as well).
try flashing a new rom, either usb-method or sd-card method should work.
a) flash a stock-rom, doesn't need hard-spl
b) flash a custom-rom, but before that you first have to flash hard-spl!!!
how to do all that -> read the stickies.

altae said:
I would not give up yet. You say you have tried installing another rom to no avail? Is hard spl installed on your phone? What kind of rom do you use (WM 6.1, WM 6.5)?
Click to expand...
Click to collapse
its WM 6.1 before the phone get restart on booting logo, in original spl
caliban2 said:
looks like your rom is messed up and can't boot anymore.
error 262 means you haven't got hard-spl (needed for task29 as well).
try flashing a new rom, either usb-method or sd-card method should work.
a) flash a stock-rom, doesn't need hard-spl
b) flash a custom-rom, but before that you first have to flash hard-spl!!!
how to do all that -> read the stickies.
Click to expand...
Click to collapse
task 29 is not working for my x1. error code [262]
wish me luck

Since you have original X1 SPL and ROM, I'm not sure, try stock ROM that is posted by PavelX1.
If it's customized, try other ROM, it's easy.

altae said:
I would not give up yet. You say you have tried installing another rom to no avail? Is hard spl installed on your phone? What kind of rom do you use (WM 6.1, WM 6.5)?
Click to expand...
Click to collapse
I think so too.....

Need help too!
On a bad day, after flashing a new ROM, my X1 was restarted in boot loader mode and never start OS any more though I tried restart, hard reset... hundred times
Has the ROM died? Please tell me what to do. Thanks.

seabreeze_pham said:
Need help too!
On a bad day, after flashing a new ROM, my X1 was restarted in boot loader mode and never start OS any more though I tried restart, hard reset... hundred times
Has the ROM died? Please tell me what to do. Thanks.
Click to expand...
Click to collapse
Yeah it is happening to me too lately and according to Russell's experience, he tells me to charge the phone @ full battery 100% then flash a new ROM (try other ROM). Task29 can be performed before flashing and removed battery for few secs as williyung recommends it. Good luck!

VSJ said:
Yeah it is happening to me too lately and according to Russell's experience, he tells me to charge the phone @ full battery 100% then flash a new ROM (try other ROM). Task29 can be performed before flashing and removed battery for few secs as williyung recommends it. Good luck!
Click to expand...
Click to collapse
Thank you for your help, but it doesn't work.
I did Task29, then original R3AA-010, then latest "2917 Energy ROM". All flashing by micro SD.
After flashing, I removed battery for a while before inserting it back, pressed power on and nothing but a 3-color screen of boot loader
Help me p...l...e...a...s...e!

seabreeze_pham said:
Thank you for your help, but it doesn't work.
I did Task29, then original R3AA-010, then latest "2917 Energy ROM". All flashing by micro SD.
After flashing, I removed battery for a while before inserting it back, pressed power on and nothing but a 3-color screen of boot loader
Help me p...l...e...a...s...e!
Click to expand...
Click to collapse
try flashing just stockrom and do nothing else (maybe a hardreset after flashing). what happens then?

caliban2 said:
try flashing just stockrom and do nothing else (maybe a hardreset after flashing). what happens then?
Click to expand...
Click to collapse
Followed your guides but nothing better. It still starts in bootloader mode automatically and cannot hard reset too.

it still doesn't find a system despite you flashed stockrom?!
well, then i'd say you have either a hw-failure or you're doing something wrong. i guess it's the second...
- after micro-sd-flash, are you waiting for the "ok" or do you remove your battery as soon as it eaches 100%? (=too early)
- what does it say on bootloader-screen, any error-messages?
flash stockrom with usb-method and see how it goes. you can also try downloading stockrom again, maybe the file is corrupted (unlikely, but...)
i'm saying stockrom because it should always work, no matter if you have hard-spl flashed or not.

caliban2 said:
it still doesn't find a system despite you flashed stockrom?!
well, then i'd say you have either a hw-failure or you're doing something wrong. i guess it's the second...
- after micro-sd-flash, are you waiting for the "ok" or do you remove your battery as soon as it eaches 100%? (=too early)
- what does it say on bootloader-screen, any error-messages?
flash stockrom with usb-method and see how it goes. you can also try downloading stockrom again, maybe the file is corrupted (unlikely, but...)
i'm saying stockrom because it should always work, no matter if you have hard-spl flashed or not.
Click to expand...
Click to collapse
Thank you for your advice.
I did ROM flashing by micro-SD and via USB many times before so I know how to do. But it's stuck into bootloader all the time I turn it on (it looks like you press & hold power+down volume button to enter bootloader mode) so I could not do flashing with USB method.
I also downloaded a fresh stockrom SonyEricsson_X1i_firmware_GENERIC_UK_R3AA010 but it still the same all the way.
I remember that it began to get stuck on bootloader few times ago and I simply did softreset until it worked normally. But now there's no way!
I already sent it to SE Service Center and they asked me to pay US$125 to change the whole mainboard!

never said you're a noob.
but yes, you can flash via usb if it's in bootloader. just connect it - pc recognizes it and you can run customruu.exe. (ignore any error-message from activesync/mobile center) i'm doing it this way all the time.
you can reflash stock-/hard-spl this way as well. maybe that would fix things.
i still think you've got a software-problem, something got messed up on your nand. for example, i had a "degenerating" file-system twice, where more and more files would get messed up in windows until the system wasn't bootable anymore (filesize 1.4 gb and such crap). after flash everything was fine and within a day - "dead". only stockrom cured that (task29 didn't). that's why i say concentrate on stockrom - it's your best chance before flashing a custom-rom again.
try everything before paying money for this old phone (replacing the mb surely would fix everything, but...). of course hw-failure is always an option, but rather unlikely in this manner.

caliban2 said:
never said you're a noob.
but yes, you can flash via usb if it's in bootloader. just connect it - pc recognizes it and you can run customruu.exe. (ignore any error-message from activesync/mobile center) i'm doing it this way all the time.
you can reflash stock-/hard-spl this way as well. maybe that would fix things.
i still think you've got a software-problem, something got messed up on your nand. for example, i had a "degenerating" file-system twice, where more and more files would get messed up in windows until the system wasn't bootable anymore (filesize 1.4 gb and such crap). after flash everything was fine and within a day - "dead". only stockrom cured that (task29 didn't). that's why i say concentrate on stockrom - it's your best chance before flashing a custom-rom again.
try everything before paying money for this old phone (replacing the mb surely would fix everything, but...). of course hw-failure is always an option, but rather unlikely in this manner.
Click to expand...
Click to collapse
Finally found the problem.
I powered up X1 with USB cable plug-in and it starts normally
I think the battery is going to die so its low voltage may caused that malfunction.
Thank you for your time.