Bricked phone TyTN II....crap....what to do ? - Tilt, TyTN II, MDA Vario III General

Hey guys, i was flashing a new ROM and after i pressed Jump SPL on the phone , i didnt do HARD SPL but went on and installed a ROM ....well now it starts with the loading screen ...........and just never loads..... any suggestions ? is it trash ?? i hope not. Thank

mfesenko said:
Hey guys, i was flashing a new ROM and after i pressed Jump SPL on the phone , i didnt do HARD SPL but went on and installed a ROM ....well now it starts with the loading screen ...........and just never loads..... any suggestions ? is it trash ?? i hope not. Thank
Click to expand...
Click to collapse
Try flashing your stock ( original ) rom, found in the wiki . And start over again.
Oh yeah, and this time it might be a good idea to read ALL the instructions FIRST.

How ?? how can you do this with out Jump SPL ? its at the first initial screen with the name of the rom.... and thats it , connecting to my computer doesnt even make a connection sound......

denco7 said:
Try flashing your stock ( original ) rom, found in the wiki . And start over again.
Oh yeah, and this time it might be a good idea to read ALL the instructions FIRST.
Click to expand...
Click to collapse
How ?? how can you do this with out Jump SPL ? its at the first initial screen with the name of the rom.... and thats it , connecting to my computer doesnt even make a connection sound......

mfesenko said:
How ?? how can you do this with out Jump SPL ? its at the first initial screen with the name of the rom.... and thats it , connecting to my computer doesnt even make a connection sound......
Click to expand...
Click to collapse
Try to put your phone in bootloader. Press and hold camera button and power button, while pressing soft reset with stylus. Once in bootloader. Connect to PC and see if you can run the RUU in your stock rom.

denco7 said:
Try to put your phone in bootloader. Press and hold camera button and power button, while pressing soft reset with stylus. Once in bootloader. Connect to PC and see if you can run the RUU in your stock rom.
Click to expand...
Click to collapse
Nope, it just does a regular soft reset , and back to the same screen

it is easy to flash it back with original rom or unlock it. just read some tutos here on xda

JugglerLKR said:
it is easy to flash it back with original rom or unlock it. just read some tutos here on xda
Click to expand...
Click to collapse
i looked into it and they had solutions if your phone is in the tri colored screen. my phone is not. my phone is in the loading windows screen... but it never loads.

mfesenko said:
i looked into it and they had solutions if your phone is in the tri colored screen. my phone is not. my phone is in the loading windows screen... but it never loads.
Click to expand...
Click to collapse
that's even better - just start it in 3color boot loader and flash!
loading windows screen appears AFTER 3color boot loader...

mfesenko said:
Nope, it just does a regular soft reset , and back to the same screen
Click to expand...
Click to collapse
Keep trying to put it into bootloader. Try a hard reset and follow instructions to get it into bootloader. Sometimes it takes several tries.

JugglerLKR said:
that's even better - just start it in 3color boot loader and flash!
loading windows screen appears AFTER 3color boot loader...
Click to expand...
Click to collapse
Maybe, I didnt Explaine it correctly but , I do NOT get the tri colored screen . This is how it goes after i press the power button to start my phone : So it automaticaly goes into loading screen where on the bottom right hand corner it shows the Radio version , the G version and some other version.......... and that is the only screen i get after staring my phone.

Maybe you didnt read well enough..
Maybe, I didnt Explaine it correctly but , I do NOT get the tri colored screen . This is how it goes after i press the power button to start my phone : So it automaticaly goes into loading screen where on the bottom right hand corner it shows the Radio version , the G version and some other version.......... and that is the only screen i get after staring my phone
Click to expand...
Click to collapse
YOU AREN'T BEING ASKED TO HIT JUST THE POWER BUTTON
try to put your phone in bootloader. Press and hold camera button and power button, while pressing soft reset with stylus. Once in bootloader. Connect to pc and see if you can run the ruu in your stock rom.
Click to expand...
Click to collapse
keep trying to put it into bootloader. Try a hard reset and follow instructions to get it into bootloader. Sometimes it takes several tries.
Click to expand...
Click to collapse
THAT MEANS DO IT AGAIN !

Thanx
Thank you denco , for the info , and thanx chumley for beating some sence into me. So i got to the bootloader. Do i need to instal my original rom or can i just reinstall the one i got or maybe another one?

well I have the same problem.
It started with the edfc problem explained here
While trying to fix that problem, I switched my rom to the TPC elite rom series (windows 6.5).
All went fine till three days later, while text-messaging, the screen freezed. I removed the battery, restarted the device and found myself having the same symptoms discussed in this threat.
Putting my phone into bootloader doesn't work, and I think It has to do with the problem I had before; that apart from the directional buttons and the power button, all buttons are defunct.
Anyone any suggestions? (apart from: don't bother us, etc, etc...)

my phone randomly bricked too a while back....as far as I understand is that either you CAN put your phone in to bootloader or your phone is junked....correct me if im wrong ppl
.....make sure you hold the camera and power buttons then reset with stylus....
and make sure you install your stock rom...aka the att tilt rom

if you didn't do it already...
1. flash your original rom (SD card method - Step 5 Flashing Via MicroSD Card ) you need the rom to be at least from the same operator. it should run just fine, just as long as you follow the directions.
2. HardSPL,SIM CID unlock, etc. as described on the same forum i pointed to a little earlier. from this point on you should have a phone just like it was when new.
try to read more carefully (maybe a few times) and search before you start a new thread.
on the wiki and in the stickies in the rom development section you get a lot of "bricked" solutions. you just have to read them all and see what is your case...

Related

did i brick my blackstone??? PLEASE HELP!!!!

When i turn on my phone I get the Tri Colored screeen
and it says: Upgrade ROM error code please try again.
and then the phone turns off and on.... Please help....
please please HELP SOMEONE!!!!
Don't dispair! I had the same problem and got out of the situation: http://forum.xda-developers.com/showthread.php?t=505377&p=3677341
You probably have the wrong Original Rom from HTC installed (may wrong language).
To solve the situation you will need USPL. USPL will install. If you are using Windows Vista you will probably have to update the drivers (See the thread).
Once USPL is running install the Original HTC 1.56-ROM.
but how can i can i installl uspl if every time i get into bootloader it turns off after 10 seconds and then turns back on...
nobody else can help??????
Try to take out the battery for one minute or two, then see what happens when switching on.
If ok (usual start) make usual normal bootloader state, and see what is your SPL. Then decide which flash you have to do.
Mr. Nick said:
but how can i can i installl uspl if every time i get into bootloader it turns off after 10 seconds and then turns back on...
Click to expand...
Click to collapse
Flash back your original ROM, you don't need USPL to do this.
For your original ROM look at this link:
http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Ship_exe
If you have problem flashing with you PC, you can try to flash from SD just extracting the files from the original ROM exe you downloaded on a temp folder (you can use winrar to do it), rename the "ruu_signed.nbh" to "BLACIMG.nbh", copy it to the root of your SD card, and flash the rom from the tri-color screen by pressing the power button.
Then, if everything is fine and your phone work again, you can think to flash a coocked ROM using USPL.
NOTE: you can read the wiki to learn something more, start here:
http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Flash1
please help me!!!!!
dalamario said:
Flash back your original ROM, you don't need USPL to do this.
For your original ROM look at this link:
http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Ship_exe
If you have problem flashing with you PC, you can try to flash from SD just extracting the files from the original ROM exe you downloaded on a temp folder (you can use winrar to do it), rename the "ruu_signed.nbh" to "BLACIMG.nbh", copy it to the root of your SD card, and flash the rom from the tri-color screen by pressing the power button.
Then, if everything is fine and your phone work again, you can think to flash a coocked ROM using USPL.
NOTE: you can read the wiki to learn something more, start here:
http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Flash1
Click to expand...
Click to collapse
sir you don't understand.... how can i flash back to my original ROM if it turns off every 10 seconds when i turn the phone on......
and also.... if i press the button on top... nothing happens.... if i put the usb cable into the phone it will go into the tri- color screen
Mr. Nick said:
sir you don't understand.... how can i flash back to my original ROM if it turns off every 10 seconds when i turn the phone on......
and also.... if i press the button on top... nothing happens.... if i put the usb cable into the phone it will go into the tri- color screen
Click to expand...
Click to collapse
It mean your phone stay at bootloader? tri-color sreen with SPL you can see. It's ok. You should download USPL 2.5 and Rom ship 1.56.4xx. Fisrt you flash SPL by running blac_uspl , your SPL will be change to 1.15USPL, then you flash ship rom 1.56.4xxx, then everything will be ok. Give it a try
Note : It's more stable if you use Win XP.
from my experience with HTC Wizard and what you are describing it
sounds like
your battery is very close to dead
you need to find a way to recharge it
your phone is protecting it by shutting off
also i don't know how valid this is for the Blackstone
but the wizard would not charge in tri-color mode
(again for battery sake)
so make sure you have a nicely charged battery (buy a spare or a table charger)
and then try to flash something again
P.S. i don't know how one sentence cries for help peppered with EXCLAMATION points encourage anyone to help you
nguyenbathanh said:
It mean your phone stay at bootloader? tri-color sreen with SPL you can see. It's ok. You should download USPL 2.5 and Rom ship 1.56.4xx. Fisrt you flash SPL by running blac_uspl , your SPL will be change to 1.15USPL, then you flash ship rom 1.56.4xxx, then everything will be ok. Give it a try
Note : It's more stable if you use Win XP.
Click to expand...
Click to collapse
A clarification of the above post. When you have 3 colors (actually 4 with white color) and USB on the white band you have to start blac_uspl.exe. That will replace the original bootloader of your phone with cracked temporary bootloader named USPL. At this stage it shall no more give errors and you may flash it from the PC or from the memory card.
The suggestion for the battery also seems fair.
Mr. Nick said:
sir you don't understand.... how can i flash back to my original ROM if it turns off every 10 seconds when i turn the phone on......
and also.... if i press the button on top... nothing happens.... if i put the usb cable into the phone it will go into the tri- color screen
Click to expand...
Click to collapse
You have to copy the BLACIMG.nbh on the microSD using a USB card reader, not your phone. Then with the microSD on the phone, in the tri-color screen, it will automatically flash your ROM, if you don't have low battery of course.
If you want to use USPL to flash a coocked ROM (for your original official rom is not needed). Your phone have to stay at tri-color screen for more then 10s.
Perhaps your problem is a low battery as someone already suggested.
Do you have tried to remove battery and put it back, let the phone off and charge it with the wall charger?
lol i did have low battery... how unlucky am i... it would shut off every so often....
but i fixed!!!!
i took out the battery and synced it with the cable..... without a battery inside and it worked!!!
I love you guys!!!!
i am not lieing i was about to cry
wow
Mr. Nick said:
lol i did have low battery... how unlucky am i... it would shut off every so often....
but i fixed!!!!
i took out the battery and synced it with the cable..... without a battery inside and it worked!!!
I love you guys!!!!
i am not lieing i was about to cry
Click to expand...
Click to collapse
LoL
Dont stress so much next time. When your stressed out you dont think with a clear head. Glad it worked out for you.
The changing of ROM only seems can not brick your phone. Only unsuccessful changing of SPL can. Until SPL is OK you may ever flash new ROM.

Is my Blackstone Dead?

Oh man
I think I also screwed up my HD. It is stuck on Loading... screen. Won't connect to pc. Can not flash anything to it. Restores ok but after reset it shows "update rom code error,please try again" and then next screen shows Loading... for ever.
Please help me guys.....
Thanks a lot
tararura said:
Oh man
I think I also screwed up my HD. It is stuck on Loading... screen. Won't connect to pc. Can not flash anything to it. Restores ok but after reset it shows "update rom code error,please try again" and then next screen shows Loading... for ever.
Please help me guys.....
Thanks a lot
Click to expand...
Click to collapse
Remove the battery put it back hold the volume down button and turn your device on. now you should be in bootloader modus and now flash a shipped rom for your device.
tararura said:
Oh man
I think I also screwed up my HD. It is stuck on Loading... screen. Won't connect to pc. Can not flash anything to it. Restores ok but after reset it shows "update rom code error,please try again" and then next screen shows Loading... for ever.
Please help me guys.....
Thanks a lot
Click to expand...
Click to collapse
Don't miss HSPL ......
Thanks guys
I can enter bootloader screen with usb at the bottom. But can not flash anything, it just sits at 0%. SPL is 1.54.
Do you have a file called blacimg.nbh on your sd-card? Obviously you can't check, so i would remove the sd-card as well and try again. If successful flash via uspl.
Thanks ATi75
I was already reading USPL and used it and voila. Its alive again. Nothing else worked. Now I will always use USPL.
Thanks again
Glad it worked out! Had a similar experience a few weeks back. Not something i want to experience again for a long while
I know. I wasted around 3 hours and lost lots of my hair.
Thanks again
tararura said:
I know. I wasted around 3 hours and lost lots of my hair.
Thanks again
Click to expand...
Click to collapse
do you have tested mtty?

Phone Struck on Tri Color Screen

Hello Guys,
I'm not sure if this is a right place to ask this question, but X1 is struck on tri color screen. Didn't do anyting, but since this morning... it's just not turning up.
Whenever I boot it up... shows tri color screen & say "loading"... cums back saying no image file & then again shows as following
KOVS110
SPL-0.78.0000
MicroP1-787
Microp2-707
Not sure if anyone else had this problem, but I'd appreciate if you can direct me to a place where it's already been fixed by someone else!
Thanks
Sachin Ghai
Try removing the battrey and wait for 10 seconds...if that helps ok, otherwise, U go in thr tri bootlader screen YOURSELF, (volume down+ power button) Do nothig, just go i the mode and come back..AGAIN< IM NOT AN EXPERT..IM JUST TRYING TO HELP U WITH UR PROBLEM....PLZ TAKE AN EXPERT'S ADVICE..
boLUCK!
Did the exact same thing...still struck at tri color screen...
All SM & Experts..I request you to get me out of this trouble..
Thanks in Advance
try to plug it to your computer via usb.. it happened to my diamond once.
I've already mailed you this
Hallo Sachin,
read the first post of this: http://forum.xda-developers.com/showthread.php?t=431218
You can use two methods, first your pc synced with your device and second the microsd procedure. i prefer the last one.
Here's the procedure for microsd: http://forum.xda-developers.com/showthread.php?t=445662
After you have done this, you can flash any rom you like, read this: http://forum.xda-developers.com/showthread.php?t=446070
So basically what you do is:
1) download hard spl
2) place it on a microsd card ( put it back in your device)
3) Hardspl from microsd ( is also in tricolorscreen)
4) Now you have hardspl'd your device.
5) download a preferred rom
6) put it on the microsd card
7) Flash.
Now your device must work again.
If you have any questions, mail me.
Greetz
If you are trying to flash a custom ROM you need hard-SPL. Follow the instructions the guy above gave to you.
Cheers!
cristidotro said:
If you are trying to flash a custom ROM you need hard-SPL. Follow the instructions the guy above gave to you.
Cheers!
Click to expand...
Click to collapse
I'm not trying to FLASH rom. I'm that techie to do all this.....However... thanx for ur efforts guys...Fortunately...the bootloader came in to normal mode & booted up in normal way... however I'm scared to off it again, as I'm not sure if it'll turn up in normal way again or not.
What do you guys think?
SHALL I HARD RESET or SOFT RESET my phone? WIll either of these solve the problem?
I don't want to play with ROM thing.... just lil scared not to turn my x1 in useless crap..

Hero stuck on boot screen

My phone was acting crazy today so I rebooted the phone and now it is stuck on the htc boot screen . I am running Fresh Toast v2.1 and haven't made any changes for over a month . I try go into recovery by holding the home key but it does nothing , just hangs . I tried to see if fresh kitchen would see the phone but it doesn't . Any help would be greatly appreciated . I have noticed that the phone will restart after hanging for about 5 mins but of course it still hangs .
I cant get into recovery , however, the only screen that comes up is the screen with 3 droids on skateboards and it says
clearstorage
Click to expand...
Click to collapse
Clear....
Click to expand...
Click to collapse
Done.....
Click to expand...
Click to collapse
<Menu> Reset Device
Click to expand...
Click to collapse
I should add that when I hold down the home and power key , it doesnt take me into recovery anymore , it takes me to the screen with 3 droid on skateboards and says clearstorage .
huedawg said:
My phone was acting crazy today so I rebooted the phone and now it is stuck on the htc boot screen . I am running Fresh Toast v2.1 and haven't made any changes for over a month . I try go into recovery by holding the home key but it does nothing , just hangs . I tried to see if fresh kitchen would see the phone but it doesn't . Any help would be greatly appreciated . I have noticed that the phone will restart after hanging for about 5 mins but of course it still hangs .
I cant get into recovery , however, the only screen that comes up is the screen with 3 droids on skateboards and it says
Click to expand...
Click to collapse
im allso having this problem i have tried like everything to restore my phone but still just stays on the htc boot screen.
cbwhat said:
im allso having this problem i have tried like everything to restore my phone but still just stays on the htc boot screen.
Click to expand...
Click to collapse
Can you get into your recovery?
huedawg said:
Can you get into your recovery?
Click to expand...
Click to collapse
i can get to the menu where you wipe and can go to usb toggle and restore to a custom rom yes
cbwhat said:
i can get to the menu where you wipe and can go to usb toggle and restore to a custom rom yes
Click to expand...
Click to collapse
Do you have a nandroid backup ? If so , try restore . I cant even get into my recovery . If dont work maybe try Turn it off and try to hold the power and home key. IF you get stuck again, hard reboot again (battery), load up, THEN turn it off again. This time, turn it on with the (-) volume button held down.
Have you tried taking the battery out for 30 seconds and putting it back in?
Dave2582 said:
Have you tried taking the battery out for 30 seconds and putting it back in?
Click to expand...
Click to collapse
yes i have
huedawg said:
Do you have a nandroid backup ? If so , try restore . I cant even get into my recovery . If dont work maybe try Turn it off and try to hold the power and home key. IF you get stuck again, hard reboot again (battery), load up, THEN turn it off again. This time, turn it on with the (-) volume button held down.
Click to expand...
Click to collapse
i have no problem getting to the recovery screen its just that i have tried different roms and they all dont work, even ones i have had installed on my hero before. it just stays at the htc boot screen. i have tried reformatting my sd card and partioning it and repartioning it. wiping everything. my nandroid backup didnt work either.
cbwhat said:
i have no problem getting to the recovery screen its just that i have tried different roms and they all dont work, even ones i have had installed on my hero before. it just stays at the htc boot screen. i have tried reformatting my sd card and partioning it and repartioning it. wiping everything. my nandroid backup didnt work either.
Click to expand...
Click to collapse
Sounds like its time to ruu
Well, if worst comes to worst, just run the RUU and start over again.
huedawg said:
Sounds like its time to ruu
Click to expand...
Click to collapse
what is ruu?
cbwhat said:
what is ruu?
Click to expand...
Click to collapse
Click on the link above that Dave provided and download that . Put it on your sd card and flash it . This will take you back to stock but you get to start the fun stuff all over again . Last case scenario . It could be worse , I mean , at least you have options . As of now , I have no way of communicating with my phone and no access to recovery . I might be screwed .
huedawg said:
Click on the link above that Dave provided and download that . Put it on your sd card and flash it . This will take you back to stock but you get to start the fun stuff all over again . Last case scenario . It could be worse , I mean , at least you have options . As of now , I have no way of communicating with my phone and no access to recovery . I might be screwed .
Click to expand...
Click to collapse
i went to usb toggle and put the ruu on the root of the sd card then i went to flash zip from sdcard and it says no zip found. what do i do?
It's a Rom Utility Update. Just download the RUU, install it, then run it. Follow the directions within the RUU. You will have to plug your phone to the PC and let the RUU do its thing. When it's completed, your phone should have a factory stocked ROM.
cbwhat said:
i went to usb toggle and put the ruu on the root of the sd card then i went to flash zip from sdcard and it says no zip found. what do i do?
Click to expand...
Click to collapse
Just go into recovery and choose flash . Find the ruu that you added to sd card and flash it .
huedawg said:
Just go into recovery and choose flash . Find the ruu that you added to sd card and flash it .
Click to expand...
Click to collapse
I believe it's an .exe file. I don't think you can flash it through recovery.
Dave2582 said:
Just download the RUU, install it, then run it. Follow the directions within the RUU. You will have to plug your phone to the PC and let the RUU do its thing.
Click to expand...
Click to collapse
well i pluged it in thought the usb during boot and in the recovery usb toggle and when i run the ruu i get a error 170 usb connection error
Try turning the phone off completely, then run the RUU again.
Isn't there another way to boot? I remember something about using the down volume button, the back arrow and booting... that's probably not the actual keys, but I know it was different from home and power. Anybody?

Phone doesn't want to boot.

My TP2 stopped working ((((((
I was using it with some cooked ROM (i think it's not relevant what exactly). This morning i had my breakfast and i've got an SMS from an acquaintance. After this i couldn't see my home screen anymore, but i could still use start menu and so on. I wasn't first time as this error happened, so i didn't thought anything and just made a reboot. After this i saw bootloader screen and it was message about missing ROM shortly to see. Nohting else, only bootscreen, hard reset didn't work either. So i came home, connected my phone via USB to my notebook, powered it on and started to flash ROM. As flash was successfully complete, the phone rebooted and i saw... bootloader again!
So i don't know what to do now, anybody some thoughts?
Djablos said:
My TP2 stopped working ((((((
I was using it with some cooked ROM (i think it's not relevant what exactly). This morning i had my breakfast and i've got an SMS from an acquaintance. After this i couldn't see my home screen anymore, but i could still use start menu and so on. I wasn't first time as this error happened, so i didn't thought anything and just made a reboot. After this i saw bootloader screen and it was message about missing ROM shortly to see. Nohting else, only bootscreen, hard reset didn't work either. So i came home, connected my phone via USB to my notebook, powered it on and started to flash ROM. As flash was successfully complete, the phone rebooted and i saw... bootloader again!
So i don't know what to do now, anybody some thoughts?
Click to expand...
Click to collapse
If you have a GSM TP2 try running Task 29 before flashing the ROM. http://forum.xda-developers.com/showthread.php?t=649191 After Task 29 then reflash your ROM of choice and then hard reset to make suer everything took.
Good luck
blutruck said:
If you have a GSM TP2 try running Task 29 before flashing the ROM. http://forum.xda-developers.com/showthread.php?t=649191 After Task 29 then reflash your ROM of choice and then hard reset to make suer everything took.
Good luck
Click to expand...
Click to collapse
Yes, i have a GSM TP2. As you advised, i downloaded Task 29, unzipped it and run ROMUpdateUtility.exe from its folder. After 100% phone booted again to the bootloader, I went to ROM's folder and run CustomRUU.exe from it to flash the new ROM. After "success" i disconnected the USB-cable and started the phone... no changes. I still see the bootloader. And i still cannot hard reset my phone for some reason.
Djablos said:
Yes, i have a GSM TP2. As you advised, i downloaded Task 29, unzipped it and run ROMUpdateUtility.exe from its folder. After 100% phone booted again to the bootloader, I went to ROM's folder and run CustomRUU.exe from it to flash the new ROM. After "success" i disconnected the USB-cable and started the phone... no changes. I still see the bootloader. And i still cannot hard reset my phone for some reason.
Click to expand...
Click to collapse
How are you hard resetting your phone? All I do is power it off then hold the send and end keys and press and hold the power button until a message pops up asking if you want to hard reset. Press the vol up key to reset and after it completes press the vol up key to reboot.
Just a random thought here--is it possible your volume down button is stuck?
blutruck said:
How are you hard resetting your phone? All I do is power it off then hold the send and end keys and press and hold the power button until a message pops up asking if you want to hard reset. Press the vol up key to reset and after it completes press the vol up key to reboot.
Click to expand...
Click to collapse
Yeah, I do the same. I hold the both outer keys and the power button but no message pops up, just the bootloader.
BigWopHH said:
Just a random thought here--is it possible your volume down button is stuck?
Click to expand...
Click to collapse
It might be possible, but if i press it, it feels like its OK. However, is there any method to test all the buttons of my phone?
Any other thoughts? Without phone i am totally f*cked up, cause i am not in my hometown right now and i have to keep contact with my business partners in there.
It sounds like your bootloader is somehow broken, if it isn't a problem with the volume down key.
Try searching for information about the "mtty" utility. It's kinda complicated, but I think it's helped people in a similar situation.
steviewevie said:
It sounds like your bootloader is somehow broken, if it isn't a problem with the volume down key.
Try searching for information about the "mtty" utility. It's kinda complicated, but I think it's helped people in a similar situation.
Click to expand...
Click to collapse
Thank's I'll inform myself about "mtty" keyword. But if u say that the bootloader could be broken, maybe i should try to reflash HardSPL or go back to stock SPL?
Djablos said:
Thank's I'll inform myself about "mtty" keyword. But if u say that the bootloader could be broken, maybe i should try to reflash HardSPL or go back to stock SPL?
Click to expand...
Click to collapse
Yes, that's another alternative, at least you can try it.
steviewevie said:
Yes, that's another alternative, at least you can try it.
Click to expand...
Click to collapse
Now I am encountering bigger problems with my device. I tried to use MTTY ver 1.42 first. I couldnt use it because there wasn't an option to choose USB-port. Yes, i unchecked "Connect via USB" in WMDC and killed it then in task manager. Then i flashed stock SPL ver 0.79, hm nothing new. Then I tried to flash the original SPL, i.e. ver 0.84 and it got stuck by 0%. I waited and waited and waited, so i had to remove cable and the battery. After that nothing worked. No flashing worked at all, even Task 29 gets stuck by 0% every time........ I dont know what to do now.....
Can you get into the bootloader still ?
steviewevie said:
Can you get into the bootloader still ?
Click to expand...
Click to collapse
Yes i do. I still see the bootloader showing me current SPL version (0.79 )
So does it still always go into the bootloader ? It won't boot ? If so, have you tried mtty to try and fix that ?
steviewevie said:
So does it still always go into the bootloader ? It won't boot ? If so, have you tried mtty to try and fix that ?
Click to expand...
Click to collapse
As i said above, i could not connect to the phone through mtty, but fortunately i have another laptop here with winxp on it so it works on it. I typed "set 16 0" and "task 8" and it booted again into the bootloader just like before.
Djablos said:
As i said above, i could not connect to the phone through mtty, but fortunately i have another laptop here with winxp on it so it works on it. I typed "set 16 0" and "task 8" and it booted again into the bootloader just like before.
Click to expand...
Click to collapse
Have you tried flashing a ROM using the storage card method? Might be some error being caused but your computer.
The following was taken from http://forum.xda-developers.com/showthread.php?t=550540
Flashing Via MicroSD Card
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the Rhodium Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to RHODIMG.nbh
4. Copy the RHODIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
You might also want to try flashing from another computer.
Djablos said:
Yes i do. I still see the bootloader showing me current SPL version (0.79 )
Click to expand...
Click to collapse
well it seems that you have flashed back to stock spl since it is showing you spl version (0.79)
which means you will have to hardspl it again in order to flash any custom roms again but it is probably unlikely that it will not work because when you reflash stock spl you are suppose to flash stock rom & radio first before flashing stock spl i'm just guessing i'm not to sure on this 1 i could be wrong though
P.S. - just a suggestion since you have stock spl back on the phone try & flash a stock rom to see if that works
Djablos said:
Yes i do. I still see the bootloader showing me current SPL version (0.79 )
Click to expand...
Click to collapse
Is that maybe the problem ? Did you flash the stock SPL back onto it as you referred to earlier ? Because 0.79 is a stock SPL version, so it won't boot a custom ROM with that SPL.
So is the whole problem that you have a custom ROM and stock SPL ? I hope it's that simple, but fear it isn't.
I hope!
Hello,
if you have 0.79 hard spl,
1. you should install stock rom, not cooked. After go to bootloader mode.
2. Run Rhodium-HardSPL_V2_00R3.exe from http://forum.xda-developers.com/showpost.php?p=4363807&postcount=1
3. Install cooked rom!
It is working!
I hope it will help your problem!
blutruck said:
Have you tried flashing a ROM using the storage card method? Might be some error being caused but your computer.
You might also want to try flashing from another computer.
Click to expand...
Click to collapse
Yeah guys, here's what i did and what i see. Before i flashed stock SPL 0.79 i flashed stock ROM and stock radio. Then i tried to flash stock SPL 0.84 and it didn't work for some reason. OK, then I read an advice from Doo Doo and tried to flash stock ROM again. I was wondering that it worked... but as it got 100% the device entered bootloader mode again! But after this the version of SPL was 0.88
I cannot use storage card method because i don't have any possibility to get access to the card from my PC And I just tried to hard SPL my phone from another PC (winxp) so it didn't work either, stuck by 0%.
Try to older stock rom. Maybe it will install older spl...
Sorry, but I couldn't help this problem! :S

Categories

Resources