hi,
i have a mda vario which i have tried to flash
first i flashed xplore 1.1 but i had a problem with my battery.
when i used te wifi the battery got from 100 till 10 in 5 min
so i tried to flash it back to the original rom
when i was doing that my mda restarted even if the flashing was stil on 30%
now when i start my mda, it keeps in the bootloader
i tried to flash the original rom again but my phone keeps restarting even if the flashing is still busy.
i flashed it again with xplore 1.1 but in middle of the flashing it restarted again.
the only way to install xplore 1.1 from bootloader is to keep my mda in de charger for at least 1 hour or else my phone wil restart in middle of flashing
now i had xplore 1.1 installed again i noticed that my battery status is unknown
i readed many topics and it say i havo to wait 10 minutes en my battery status changed to normal but no
also i tried to flash a radio but when i do that my mda restarts in middle of it
i tried to use my mda even if the battery status is unknown but if i use my wifi connection my mda wil restart after 5 to 10 minutes.
does someone knows how i can solve this by my self for free?
phone:
mda vario
g3
ipl/spl 2.06
greetz acxtreme
Related
does anyone know why this happens?
has anyone found a workaround?
i think this rom work well... i using about one week
most modern roms take 10-15 mins to pass from 98% to 100%...so wait...and wait...and wait...
Ditto
You gots to wait!
i should still wait 15 minutes after the computer says 100%
it has been 15 minutes and still at 99% how much longer
the update utility says congratulation! wtf
20 minutes and i am almost ready to flashback?
whats the problem? what roms haved you tried updating from i,ve tried
2.26 2.3 and 3.2 rc1?
both in the computer and the wizard it stay at the same number, if the computer finished be4 then there is a problem...
Whats your IPL/SPL version number?
had the same problem,
and wasn't patient :$
now i get stuck in the boatloader :s
another upgrade isn't a go since i itz not connected
to active sync?
is there a way out :s
haha, you don't have to be connected to activesync.
Just boot it in boot loader mode and plug it in. You can flash like that.
That's actually how I do all my flashes.
I am just on bootloader ...
itz stuck there :s
any reponse
i would like to try flashing again any ideas because it didn't work the first five times.
Me too
I have a G3 T-Mobile wizard (no .001), and it stuck at 99% with the PC version saying finished. I waited 25 minutes, gave up (there is a battery issue!) and reflashed with Molski's 2.26.
how can u flash it again?
I am in bootloader and stuck there no updates work nothing :s
prestonmcafee said:
I have a G3 T-Mobile wizard (no .001), and it stuck at 99% with the PC version saying finished. I waited 25 minutes, gave up (there is a battery issue!) and reflashed with Molski's 2.26.
Click to expand...
Click to collapse
If you have .0001 then you have a G4 Wizard and NOT a G3 Wizard.
Molski
no no
molski said:
If you have .0001 then you have a G4 Wizard and NOT a G3 Wizard.
Molski
Click to expand...
Click to collapse
Yes, but I have "no .001", which should have been "no .0001".
Is your rom the same as T-Mobile 2.26 if I don't install the extended rom? (I install my own extended rom manually.)
Kartboy: As goldrush98 said, you don't have to be connected to activesync. If you see "usb" on the tri-color bootloader screen, just start the rom flash program and it will flash the new ROM. Worked for me.
please stick to topic
the topic is ell AKU 3.2 rom 99% crash not ell AKU 3.2 rom ipl/spl
i do not think the crash has to do with ipl b/c i know i have a G3
where is the developers response
Same issue here.
I have the same problem here. Mine gets to 99% on the phone and the computer says it's done. I've waited over an hour for the phone to finish.
Well I am a newbie and having a lot of fun upgrading until tonight.... I unlocked the mda vario and upgraded first with official t-mobile version then with the aku 3.3. My mda is a g4 and not cid unlocked, but I managed to load the aku 3.3 with the shelltool.... After I did everything the phone was a total brick... Could connect to pc, couldn't turn. The main page was coming up and giving the version of the mobile but wouldn't do anything else. So I tried pressing the call button and the wireless button and quickly pressed the reboot little button on the side. The screen became green and red, with something else written. When I did that and I tried to upload the software off t-mobile from http://www.tm-phonedownloads.com/download_manager_mda_vario.html, the software sort of recognized, than it asked to disconnect and take out battery. After I had to put back in and the usual start screen was coming up, but as the t-mobile software was asking if the red and green screen was up I repressed the call and wireless button and said yes. After that the phone was upgraded to the firmware off t-mobile and now is working fine again. It was scary though, so think twice before upgrading....
if you follow the instructions properly in the shelltool thread.
http://forum.xda-developers.com/showthread.php?t=293480&page=14
iv attached a tutorial on page 14 of that thread. you should be able to successfully upgrade rom
if anything goes wrong. boot your phone in bootloader mode and use the wizardlove rom to fix it.
i spent 7 hours last nite tryin to upgrade rom in which i mustve recovered my fone liek 6 times using the wizardlove rom
wizard love
yeah same here mucked my phone up the first time then read the instructions followed them and now running underground crossbow edition now have flashed rom about 3 times with different ones if you read the instructions works fine
wizard love saved my phone also
Greetings,
Can you tell me where would i get wizard love rom.
Thanks
hjkl;' why no delete?
Hello,
Iám Spanish and I just bought a MDA VARIO in GErmany, so I tried to install the spanish rom "2.18.7.8" and i did it. Everything was ok during installation, but when I restarted... The device couldn´t restart. It allway stop on the Qtek screen(with the sky), sometime it change the screen into a white(HTC innovations) one for a second. But it doesn´t work.
I made soft and hard reset, but nothing changes.
I also tried to install an other rom by bootloader way, but the rom sais that is not possible to contact with the phone device.
I´m scared and I don´t know what to do.
Know this is the rom´s I have on my Qtek 9100 :
IPL 1.06
SPL 1.06
OS 2.18.7.8
Help please!!
Jmavatar said:
Hello,
Iám Spanish and I just bought a MDA VARIO in GErmany, so I tried to install the spanish rom "2.18.7.8" and i did it. Everything was ok during installation, but when I restarted... The device couldn´t restart. It allway stop on the Qtek screen(with the sky), sometime it change the screen into a white(HTC innovations) one for a second. But it doesn´t work.
I made soft and hard reset, but nothing changes.
I also tried to install an other rom by bootloader way, but the rom sais that is not possible to contact with the phone device.
I´m scared and I don´t know what to do.
Know this is the rom´s I have on my Qtek 9100 :
IPL 1.06
SPL 1.06
OS 2.18.7.8
Help please!!
Click to expand...
Click to collapse
With activesync on it will say it won't detect the phone plugged in while it's in bootloader mode. Run the ROM update anyway.
Thanks, but it doesn´t work. The Rom software said that is unable to connect with the phone.
I just tried to install the vanilla WM6, and with zhis rom, the installation could begin, but at 95% it happen an error... and i need to reinstal an other time the vanilla WM6.
I tried an other time, but the same error on 95% :-( And i can´t instal others rom.
did you CID unlock?
enter bootloader and flash the original rom from that screen, then start again. if you don't know how to get into bootloader screen or what CID lock is, read the wiki and the stickies in the forum. Don't worry, it is not a brick
bbobeckyj said:
did you CID unlock?
enter bootloader and flash the original rom from that screen, then start again. if you don't know how to get into bootloader screen or what CID lock is, read the wiki and the stickies in the forum. Don't worry, it is not a brick
Click to expand...
Click to collapse
Thanks a lot for our support! I still tnhinking I have a brick :-S... Now It only apears the bootloather screen(three colors bars) due to the incompleted vanilla WM6 uppdate.
I think the CID is unlocked. I runed the Lokiwiz, but now, I am not sure if It worked... And now, the phone is without battery!!
Where I can find my original rom? The device is from T-Mobile and is a MDA VARIO. From Austria. I have 2 CD´s, one with windows 5 applications, and other with software... I can´t fin the rom.
Thanks a lot!!
there is a link to the US tmobile ROM in my signature. it may work, i don't know.
as for the dead battery, you have a few options,
1) charge the battery in a desktop charger such as this one from ebay.
2) try charging in a friend's wizard
3) i have read references to charging the battery with a n-i-n-e v-o-l-t battery and a p-a-p-e-r-c-l-i-p (i've typed it like that because there are getting more and More references to things than actual solutions when you search) battery many times, try googling this site for that (again in my sig).
the ROM is not on any CD they give out with it because they don't want people flashing their devices and ending up in the situation you are - why do you think they are locked.
bbobeckyj said:
there is a link to the US tmobile ROM in my signature. it may work, i don't know.
as for the dead battery, you have a few options,
1) charge the battery in a desktop charger such as this one from ebay.
2) try charging in a friend's wizard
3) i have read references to charging the battery with a n-i-n-e v-o-l-t battery and a p-a-p-e-r-c-l-i-p (i've typed it like that because there are getting more and More references to things than actual solutions when you search) battery many times, try googling this site for that (again in my sig).
the ROM is not on any CD they give out with it because they don't want people flashing their devices and ending up in the situation you are - why do you think they are locked.
Click to expand...
Click to collapse
Thanks a lot!! But it doesn´t work. Error[294] Invalid Vender ID :S
I can charge the battery with the normal charger to 220v.
Any idea??
My IPL is 1.06
and SPL 1.06
did you buy it from tmobile or ebay? (is it german tmobile or just bought in germany?)
go to the tmobile site and look for firmware/software updates for the mda vario. i don't know german so i could not find the mda vario on it
bbobeckyj said:
did you buy it from tmobile or ebay? (is it german tmobile or just bought in germany?)
go to the tmobile site and look for firmware/software updates for the mda vario. i don't know german so i could not find the mda vario on it
Click to expand...
Click to collapse
I bought yesterday on a T-mobile shop from Austria. I downloaded it´s roms... but the same problem.
I will carry the device to the shop...
Thanks a lot!!
try this button rom
http://rapidshare.com/files/18212239/CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe.html
then have you followed the intructions in Dr Ps thread
http://forum.xda-developers.com/showthread.php?t=285435
do not give up
bbobeckyj said:
try this button rom
http://rapidshare.com/files/18212239/CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe.html
then have you followed the intructions in Dr Ps thread
http://forum.xda-developers.com/showthread.php?t=285435
do not give up
Click to expand...
Click to collapse
Thanks again, but I returned the phone to the shop. Something didn´t work since the beginning. Tomorrow I will reveive a new one...
Thanks an other time!
Hi,
I got a similar problem.
I wanted to install the latest AkU 3.3 on my MDA VARIO but it stopped at 95%.
So I tried to install the oldest version available from T-Mobile Germany.
But now my device restarts again and again.
It says
IPL 1.06
SPL 1.03
OS 2.24.2.8.
and restarts.
Sometimes (with the oldest software version) I can calibrate my touchscreen and then the device installs the T-Mobile software. After that it restarts again and again.
I also tried softrest after the message: in 3 seconds .... software will be installed. Then it reboots and sometimes wm5 starts but is running VERY slow. I can't switch it off using the power buttom.
I unlocked my MDA Vario using Lokiwiz. No CID Unlock just Unlock.
What can I do?
Thanks in advance
very simple, flash back to your original rom, then, CID UNLOCK
Hi,
I Tried to update my mda vario with a new rom. During the update my laptop, which I used to update the rom, crashed. The firmware update was at 96%.
When I rebooted my mda, I saw only a rgb screen. I searched the xda forum and saw that it wasn't a big problem. I only had to start the update proces again.
From that moment the real problems started. When I tried to update again, the phone rebooted several times during the update and the RUU gave several errors, every time another error code. I saw the error codes 300, 302, 264,274,262.
Every time I removed the battery and waited several minutes. At one point I had the battery removed for 8 hours. But every time I try to update the phone reboots during the update process (I see the percentage bar in the screen of the mda)
I tried several roms now, the roms i have tried are:
Wizard_Love_2.26.10.2_WWE_Novii_CF2
RUU_Prodigy_2210205_22102108_021911_TMO_NL_DUT_Ship.exe
MDA_Vario_1060202_103_11210_TMNL_Ship.exe
None of the roms succeedes to install.
Because, I am trying to update for 2 days now, I thought maybe my battery status is lower than 50%, so I wanted to load the battery to a 100%. When I connect my power adapter to the phone, the charging led will turn on, but the phone starts up (shows the RGB screen) and the charging leds turn off. So it seems I can't charge the battery either.
HELP!!!
Kind Regards,
Patrick
You didn't claim your IPL and SPL version, however it is almost confirmed that you didn't read the stickies here carefully. You need to CID-Unlock (G3) or HardSPL (G4) your device before flashing any ROMs!
For now, get your MDA Vario stock ROM and flash it, then you can get a working OS back. Then refer to the stickies.
starkwong said:
You didn't claim your IPL and SPL version, however it is almost confirmed that you didn't read the stickies here carefully. You need to CID-Unlock (G3) or HardSPL (G4) your device before flashing any ROMs!
For now, get your MDA Vario stock ROM and flash it, then you can get a working OS back. Then refer to the stickies.
Click to expand...
Click to collapse
And with your answer it is confirmed that you didn't read my post well.
But the problem is solved, i found a similar phone and could charge my battery, and I updated the phone with the stock version.
Hello everybody.
So the problem is this. I got a QTEK 9100 today, and it happened to be in swedish (got in from a friend, for free). It was WM5 anyway so i decided to update it to WM6 or newer. I followed the original guide to flash rom (i did everything as they were supposed to do) I got the Wizard Service tool, checked the right G-thing. I do have G3 device and i did follow the G3 guide.
But when i tried to flash it did came with an ERROR 262 CONNECTION ERROR. And then it put me to the recovery instructions. I went them trough -cable off, power off, cable back, power back) I tried to re-flash it three times, but it was ALWAYS stuck at 26% giving the same error over and over again.
I re-installed Activesync. I didnt get no connection this time (before reinstall i did get connection). Altrough my computer says something at lower right that it detected a device.
Then i tried Xda_MiniS_LaunchROM_v154102. I tried it two times, same error 262 and stuck at 11%.
Now it wont upgrade to anything. CID is still locked.
Im stuck in the three color space at the beginning. My IPL is 1.05 and SPL is 2.17. I do get the USB in bottom left of the screen.
Any help would be appreticiated. I dont want to brick my new phone.
Greetings. Hurrikaani
have you tried to flash button rom on your device?