Related
Hello to all,
Can it someone explain to me in steps how I can install WM6 on my HTC3600?
Currently is on Germany language, but I would like to switch it on English.
Thanks a lot on your help.
Regards
1) decide which rom you want (I used LVSW)
2) go to the thread and read 1st post
3) grab the 3 files attached
4) they are zip's, extract each to thier OWN folder.
5) go to each folder IN TURN as listed in the thread and run ROMUtilityUpgrade that is enclosed IN EACH folder.
STOP between each folder / Upload to phone and check your phone
THE VERY first one HardSPL MAY give an error, HOWEVER just run it again, seems ActivSync throw a fit and then the computer has to re-connect, HOWEVER after that off you go.
ALSO use NON-Vista machine
deech said:
1) decide which rom you want (I used LVSW)
2) go to the thread and read 1st post
3) grab the 3 files attached
4) they are zip's, extract each to thier OWN folder.
5) go to each folder IN TURN as listed in the thread and run ROMUtilityUpgrade that is enclosed IN EACH folder.
STOP between each folder / Upload to phone and check your phone
THE VERY first one HardSPL MAY give an error, HOWEVER just run it again, seems ActivSync throw a fit and then the computer has to re-connect, HOWEVER after that off you go.
ALSO use NON-Vista machine
Click to expand...
Click to collapse
HUH...YOU ARE REALLY FAST..THX...
SO...
1. what is LVSW? I will use same like you
2. i just need to connect my HTC with a PC and start applications from 1st thread? or before that I need to do something more?
go here http://forum.xda-developers.com/showthread.php?t=305250
grab the 3 downloads and put them safe
Extract each to it's own folder.
Do them in the order listed in the post ... HardSPL, Radio, WM6.
Enjoy
deech said:
go here http://forum.xda-developers.com/showthread.php?t=305250
grab the 3 downloads and put them safe
Extract each to it's own folder.
Do them in the order listed in the post ... HardSPL, Radio, WM6.
Enjoy
Click to expand...
Click to collapse
Really....THX!
It works man, thank you once more!!!!!
Can you give to me little help with a GPS tomtom 6....?
What I need to download and install?
No worries
What exactly do you want to know about tom tom?
First off I'll assume you are buying the software. In which case you want this
http://www.tomtom.com/products/product.php?ID=281&Category=2&Lid=1
now you dont have to buy it from them direct, however that is the product you want (it may be cheaoer elsewhere)
If it's already on a memory card.... just pop the card in the slot and it'll do everything for you.
I would HIGHLY recommend making a copy of the card contents to your computer, just use activ synch and explre the device till you get to the storage card then copy and paste the entire contents of the card to somewhere safe.......
Then EITHER push this up to a larger card or carry on with the card you buy.
Install Tom Tom home on your computer, it will then synchronise your maps and voices and stuff BUT more importantly it'll auto update your software for you.
You need to be running 6.03
in this version tom tom can be set to use "built in gps receiver" after that away you go... simple and Deech proof
edit for spelling mistakes
lol.. you are really fast....
can it be anything without buying orginal software or maps ?
It can and if you know where to look I am sure you will find what you seek young Jedi
I arent going to preach but note I did buy this software mainly for updates and technical back up
If you "acquire" the software read any threads / forums from the place where you get it from
Fast cos laid on the couch nursing a size 10 thick head after last night
ihihihihihi...
okay..... i will search... my the force be with me
Again problem,
Im facing with extremly battery drain, after charging standby was just 36 hours, before was around 5-7 days i think.
Is there any solution for this??
Thank you... Mr.Vader
An my young jedi, yes there is....... and if I can get it to work it should be attached to this post.... Also read the MuN RUS Rom thread it has been flagged-up thier with alsorts of solutions including this .cab
Drop it onto your memory card and ermmm run it
I get an corrupted image error when I try and flash the hard-spl?
Anyone know how I can get around this? tried searching for info and the search function just brang up unrelated posts, and theres nothing on the wiki despite it being a common problem.
So please forgive my stupidity, and enlighten me on how to solve this?
I have an M700 with shipped rom installed
Thanks in advance,
WWWeed
after i upgrade to wm6, how hard is it if i want to go back to wm5, how hard is it to downgrade? Do I have to back anything up?
back up contacts etc
back up ringtones etc
grab a rom with WM5 in / on it, and re-re-flash the phone, leave the radio rom as it was mind as it's seperate from the WM section
deech said:
An my young jedi, yes there is....... and if I can get it to work it should be attached to this post.... Also read the MuN RUS Rom thread it has been flagged-up thier with alsorts of solutions including this .cab
Drop it onto your memory card and ermmm run it
Click to expand...
Click to collapse
Ahhh great thanks.
Just what I was after.
As you are using the LVSW like myself you may have an answer to my other question.
Is there a .cab file to fix the awefull sound on WM6 and the trinity?
Media player is so quiet, if I can't fix it, I'm going back a stage to WM5 as I use the MP3 player side of it allot.
Many thanks.
Shaun.
Hi,
i have just loaded wm6 following the instructions here and now i am getting USB device is not recognized.
Can anyone suggest a solution?
Thanks
Stephen
are there any issues not completely solved on the available non-official WM6 ROMs for Trinity?
I'd like to upgrade mine, but only if all the initial problems have already been solved.
BTW, my Trinity came with TomTom 6 pre-installed. If I upgrade to WM6, will I have to purchase and install a new copy of the software?
All seems to work fine now, any issues then there will be a .cab file around here somewhere, main ones are ATIfix, when does somthing to make tomtom work nicely, power fix which address' some power useage issues.
The tomtom that come with the handset is a crippled try before you buy version (well it is here in the UK ) So ermmm yes, you would need to buy a full version, but on the plus side it's yours forever and no matter what you do to your phone you can always put it back Unless the tom tom is on your SD card in which case REMOVE the card before you start and re-install when you've finished rom-ing
Failed with upgrade to wm6
Hi all
I just got mine 3600 and tried to upgrade to wm6 with the 3 files. When I run the first hard-spl program I had problems with the connection with the usb cable. The program aborted after a second or so. Now I am stucked with this colured image with the text
TRIN100
IPL-0.50
TRIN100
SPL-1.07.0000
is there any way for me to correct this. Or do I have to send the phone for repair?
Grateful for all help
/adam
Active sync doesn't get a connection to the 3600 anymore....
Read the second post in this thread, on page one, in the instructions I wrote it tells you THIS IS NORMAL, dont worry about activesync, when doing hard SPL the first time it regularly disconects and hangs the phone with the tri-colour screen, soft reset the phone and re-start the procees (ie run the first file again). That should see you right
ok, I have read all there is to read on this site and on WIKI. What good is it if what I am reading makes no sense to me? I know what .cab files are and how to use them, but what is a .rar file and how do I unrar or unzip it? Do i really need to create files in DOS?
All I want to do is upgrade my BA (sx66/cingular using unlocked on tmobile) to windows mobile 5.0. I know there are way too many threads on here about people who are getting stuck or having certain errors or need help in some way. I can't even get started! The few "step by step" guides I found, start off easy enough an 3 steps into it they referring to things that I have no idea what they are or how to do (yes i have read all the "please read before asking questions" stuff) Again what good does it do if you dont know what you are reading. Maybe its not broken down into simple enough terms for the average joe.
In any event, is there anyone that can shed some light on this stuff for me or aid me in a walk through. Or am I just out of luck because of my lack of software engineering knowledge? Thanks for your time all and I appreciate any feedback. Surely there is someone out there as dumb as I in this area that made it through (or at least I can hope)
You need winrar (www.winrar.com) to "unrar" the files in order to use them.
Winrar works just like winzip but it handle .rar files. So basicly you will download winrar to your computer, install it, then download the rar file with the rom you want to upgrade your device.
Using winrar open the rom archive and extract to a folder on your computer.
Run build.exe, select the options you want for your rom and press the > button.
From there do as the guide says.
spunk32, calm down We are here to help, not kill newbies
Two things:
1. When you don't understand some terms like "unrar" that not PDA-related, just google it. Things like this are considered basic here
2. When you have specific problem about one of the points, post a question (let's keep it in this thread) and smb will try to explain. But try to understand some of us, that we are not going to explain how to copy or download a file
General comment:
ROM upgrading is not totally safe and error-prune. You have to understand fully what are you doing and what for/what is the result. Basic knowledge of the way the PDA works is also good, to make good decisions on the way. That's why I do not consider updating (especially BA from WM2003 to WM5) as a task for everybody (for ex. I think that updating WM5 to WM6 with full unlocking of Hermes is much easier, but still not safe).
I would propose you to use Baniaczek's ROM (instead of XPlode rom cooking set - I looked at the PDF guide - yes, this one is complex, but some of the pictures might be helpful) as there is one step less on the way.
Full guide for you is here (on bottom of the page)
http://wiki.xda-developers.com/index.php?pagename=Helmi
You should go through all the options here, when you update from WM2003. Remeber, that going back to 2003 needs to go through another procedure, that will recreate ExtROM (yes, this is one of the magic words you should understand to play with ROMs).
Thanks for the info guys. ill delve a little deeper and see what happens. im sure ill be back on here with a post when i come to another speed bump. thanks again.
ok, i have gotten this far: downloaded winrar software, downloaded the following ROM-Helmi_BA_WM2k5_AKU3.5_v1.4.CF2.R2. Then I clicked on MaUpgradeUt_noID.exe. When i click continue on the welcome screen, the next screen shows "software converting from....to..." all the data fields are blank. Is this normal and am I on the right path? I did NOT click on upgrade to continue the process b/c I wasnt sure if I had missed something. Thanks again all.
Read what I posted moment ago in "No data from device in MyUpgradeUt" thread. I just checked again screen while updating Xplode on my BA:
In From fields there is only Radio version
In To fields, I have only Ce Image Version: 5.35.05
All other fields are emplty (and not important after all, especially nonexisting ExtROM).
Press your power button, the record button (has a cassette on it) and your reset button at the same time. Wait for the Serial or USB to show on the screen (will be dark) then flash your ROM.
It is in the forums around here somewhere on how to do that but I am to busy to find it for you to post a link.
ok, i think i made a mistake. i got as far as the step where it says you MUST say YES to the first two things on the reboot screen or whatever. all of them said NO, i tried to change it to YES , but i did not know how to change it. i hit the mail button and the screen white and loaded as is. how do i get back to the screen where i need to make the "YES" changes and how do i change NO to YES??
ok, i re-read and saw where i missed how to toggle the YES/NO. so since i was dumb enough to miss that what have i done by not changing the "NO"s to "YES"s? The device seems to be working fine. Is there something that I am not aware of yet?
If you restarted the device and made the hard reset again, this time correctly (selecting proper settings) device should work fine.
You might not noticed, but if you take battery out for while and then start the device, radio won't start (there will be no version next to letter R - means GSM mopdule won't work). You need to make soft reset few secs after first starting of the device to make it run. This is on of not so many problematic things with BA under WM5.
i have not done anything to reset the "yes/no" settings and the device has been working fine all day. i dont ever take off my battery so hopefully i wont have the problem you were refering to.
also, is there any way to remove the camera software since i dont have a camera on my device.
how do i upgrade the radio? i tried WIKI, but i got error messages and when i tried to follow the troubleshooting the links didnt work. outdated i guess.
If you never done correctly hardreset of you BA, you should - you can have a lot of odd problems without hard reset after installing (or upgrading) WM5.
Radio: I followed Wiki and made update radio (1 year ago) from some old version up to 1.13 - without any problems. Follow step after step and port exact error message and on what was happening a this exact moment.
ok, i reset and corrected to NO, YES, YES. thanks. what about removing camera data? any ideas?
You cannot delete apps that are already included in the ROM - this is Read Only Memory, as you know.
When you feel comfortable with flashing and playing with all those files, you will be ready to try xplode kitchen in which you can just select stuff you need to be included in the rom. Manual is a bit longer but still nothing really hard. You can find PDF with full instruction on Wiki pages.
ok i understand what your saying about the camera app. i have tried many times and many versions of the radio upgrade and none work. i have gotten just about every error code there is. am i supposed to be in that "boot" mode when i run it or simple be synced? ill keep looking for a thread that has recent info, but what i see is out of date with links that are no good.
You should follow http://wiki.xda-developers.com/index.php?pagename=BA_Radio_1.15_Upgrade and Second Methord Type I EASY (this is the one I used). Because you have no camera, you device is PH20B1, but AFAIK radio is the same.
You need to put your device in "serial" booloader mode (non backlighted screen, "serial" or "USB" written in lower part of the screen depending on USB cable connected or not (Power+Softreset+Record).
blue tooth wont turn on
the wm5.0 has been working great. the only problem i am having is that the blue tooth wont turn on. i have tried every method of enabling it, but it always shuts itself off. any ideas?
DaveShaw Edit:
Split the thread from the NBH Extract thread.
Hi there!
First off all thanks for the great help and all the hard work you all doing!
Keep on going!
I have problem extracting my "RUU_signed.nbh" file using the the "NBHextract" tool. The "nbh" file I need is from the:
"RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship" Rom.
I'm trying to extract with the CMD, or trying to drag & drop the "RUU_signed.nbh" onto the "NBHextract", its says in the CMD: extracting. Bat in fact, noting happens! There only the same 2 file in the folder and nothing else.
Can any one help?
Maybe some of you can tray to extract the file and upload the result to www.rapidshare.com or somewhere else?
I'm using desktop with XP PRO English.
Please! I'm going crazy!
Shaico said:
Hi there!
First off all thanks for the great help and all the hard work you all doing!
Keep on going!
I have problem extracting my "RUU_signed.nbh" file using the the "NBHextract" tool. The "nbh" file I need is from the:
"RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship" Rom.
I'm trying to extract with the CMD, or trying to drag & drop the "RUU_signed.nbh" onto the "NBHextract", its says in the CMD: extracting. Bat in fact, noting happens! There only the same 2 file in the folder and nothing else.
Can any one help?
Maybe some of you can tray to extract the file and upload the result to www.rapidshare.com or somewhere else?
I'm using desktop with XP PRO English.
Please! I'm going crazy!
Click to expand...
Click to collapse
I'm lost sorry
Have you downloaded the exe and need the NBH File? If so Install WinRAR, right click the exe and click Extract...
If you have the NBH file, then I suggest you re-try the steps you quoted again. Let me know if there are any errors on any steps.
Ta
Dave
DaveShaw said:
I'm lost sorry
Have you downloaded the exe and need the NBH File? If so Install WinRAR, right click the exe and click Extract...
If you have the NBH file, then I suggest you re-try the steps you quoted again. Let me know if there are any errors on any steps.
Ta
Dave
Click to expand...
Click to collapse
Well, I did those steps before, bat have no result. Don't see any error at the CMD. only show me the extract progress and at the end (after 2 min), there are no result! Only the same 2 file I started the progress. (RUU_signed.nbh + NBHextract tool)
I have the NBH and need to extract it... So I can continue to step 6 at these guide: Reverting back to the AT&T or HTC ROM and SPL for Warranty or return http://forum.xda-developers.com/showthread.php?t=335568
Can any one trey to extract the RUU_signed.nbh from
RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88 .07_1.27.12.11_Ship" Rom for me and upload the result?
Thanks in advanced!
Ok, update! I try to extract this in vista by drag & drop, and it worked!!! Bizarre...; and I got 5 file from the extract. The CMD still didn't work in the vista though...
Bat now i'm confused, because I read on other thread that I need to do Hard SPL first so I don't brick my TyTn 2 device... and in the guide:
(http://forum.xda-developers.com/showthread.php?t=335568),
its says I don't need to do Hard SPL. So what should I do?
let me tell you the reason I want to flash the SPL: I install Hebrew support pack that I download from the net and it work ok till I start to notice a rapidly massage of low memory (I didn't install nothing else!), bat the most reason fact that I want to flesh the SPL is because in addition of that message, the cracked Hebrew pack, showing me the logo of the company that made the pack; every time I restart the device, just before the HTC welcome logo and its showing for at lest 30 sec!!! Every soft reset!! So I try to uninstal that pack and its still showing every restart! Even, try to up grade to WM6.1, and still its there!!!! So I start to read some thread and think I need that spl flash so I can get rid of that "sticky" logo that slow my device and steal my memory!!
Can any one now something like that issue, and what shold I do in order to uninstall that long logo?
Shaico said:
Well, I did those steps before, bat have no result. Don't see any error at the CMD. only show me the extract progress and at the end (after 2 min), there are no result! Only the same 2 file I started the progress. (RUU_signed.nbh + NBHextract tool)
I have the NBH and need to extract it... So I can continue to step 6 at these guide: Reverting back to the AT&T or HTC ROM and SPL for Warranty or return http://forum.xda-developers.com/showthread.php?t=335568
Can any one trey to extract the RUU_signed.nbh from
RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88 .07_1.27.12.11_Ship" Rom for me and upload the result?
Thanks in advanced!
Click to expand...
Click to collapse
Ok, update! I try to extract this in vista by drag & drop, and it worked!!! Bizarre...; and I got 5 file from the extract. The CMD still didn't work in the vista though...
Bat now i'm confused, because I read on other thread that I need to do Hard SPL first so I don't brick my TyTn 2 device... and in the guide:
(http://forum.xda-developers.com/showthread.php?t=335568),
its says I don't need to do Hard SPL. So what should I do?
let me tell you the reason I want to flash the SPL: I install Hebrew support pack that I download from the net and it work ok till I start to notice a rapidly massage of low memory (I didn't install nothing else!), bat the most reason fact that I want to flesh the SPL is because in addition of that message, the cracked Hebrew pack, showing me the logo of the company that made the pack; every time I restart the device, just before the HTC welcome logo and its showing for at lest 30 sec!!! Every soft reset!! So I try to uninstal that pack and its still showing every restart! Even, try to up grade to WM6.1, and still its there!!!! So I start to read some thread and think I need that spl flash so I can get rid of that "sticky" logo that slow my device and steal my memory!!
Can any one now something like that issue, and what shold I do in order to uninstall that long logo?
Shaico said:
Ok, update! I try to extract this in vista by drag & drop, and it worked!!! Bizarre...; and I got 5 file from the extract. The CMD still didn't work in the vista though...
Bat now i'm confused, because I read on other thread that I need to do Hard SPL first so I don't brick my TyTn 2 device... and in the guide:
(http://forum.xda-developers.com/showthread.php?t=335568),
its says I don't need to do Hard SPL. So what should I do?
let me tell you the reason I want to flash the SPL: I install Hebrew support pack that I download from the net and it work ok till I start to notice a rapidly massage of low memory (I didn't install nothing else!), bat the most reason fact that I want to flesh the SPL is because in addition of that message, the cracked Hebrew pack, showing me the logo of the company that made the pack; every time I restart the device, just before the HTC welcome logo and its showing for at lest 30 sec!!! Every soft reset!! So I try to uninstal that pack and its still showing every restart! Even, try to up grade to WM6.1, and still its there!!!! So I start to read some thread and think I need that spl flash so I can get rid of that "sticky" logo that slow my device and steal my memory!!
Can any one now something like that issue, and what shold I do in order to uninstall that long logo?
Click to expand...
Click to collapse
OK I see what your getting at... Some facts first...
1. The guide you posted a Link to advises how to restore the Stock SPL and ROM if you have Hard SPL and a custom ROM. It does not mention Hard SPL for the simple fact that it is a guide on how to remove it (assumes you have it otherwise you wouldn't be reading the guide).
2. The SPL is the bootloader similar (in ways) to your PC's BIOS. I am pretty certain it has not been comprimised.
Firstly we need to know which splash was changed. There are 3 possible splashes that could have been changed. Have a look at this guide by -888- on upgrading you splash.
It is most likley to be one (or both) of the last two. Changing the first one requires Hard SPL and Flashing.
Rather than fixing the splash screens, I'd do a Hard Reset that will remove everything that was not part of your original OS ROM image.
If it is still there after that, I'd flash HardSPL and then flash a new Splash screen.
And, finally , this forum does not support cracked software, I will help you remove it however, if you promise to pay for it in the future
Ta
Dave
DaveShaw said:
OK I see what your getting at... Some facts first...
1. The guide you posted a Link to advises how to restore the Stock SPL and ROM if you have Hard SPL and a custom ROM. It does not mention Hard SPL for the simple fact that it is a guide on how to remove it (assumes you have it otherwise you wouldn't be reading the guide).
2. The SPL is the bootloader similar (in ways) to your PC's BIOS. I am pretty certain it has not been comprimised.
Firstly we need to know which splash was changed. There are 3 possible splashes that could have been changed. Have a look at this guide by -888- on upgrading you splash.
It is most likley to be one (or both) of the last two. Changing the first one requires Hard SPL and Flashing.
Rather than fixing the splash screens, I'd do a Hard Reset that will remove everything that was not part of your original OS ROM image.
If it is still there after that, I'd flash HardSPL and then flash a new Splash screen.
And, finally , this forum does not support cracked software, I will help you remove it however, if you promise to pay for it in the future
Ta
Dave
Click to expand...
Click to collapse
First off all, thanks for the help. I appreciate it!
I must mention that I buy the original version in advanced. I just was curious to check the net version and it turns out that it's not so good... to such an extent that I ruin me Kaiser...
now let me be more specific with me problem because i m not sure I explain the problem clearly and I don't want to start a progress that I don't know how to do....
So, like I say, after I finish the install of the language pack, I had to clear storage in order to crack the license. But since that, every restart, appear the logo of the software company for 30 sec!!! Every restart!!!! Its make me crazy!!!! (The logo appear just before the HTC logo load. (It's appear with the rom and the radio version = R.G.D). But this is not the main problem!! The most important problem is that since the install, its keep say me that I'm run out of memory, and I m even didn't install nothing!!! This is bad!
So off Corse I'm try to do hard reset and even try to upgrade to WM6.1, but the cursed logo is still there!!!!
Now, after I try to explain the problem, I want to know if the solution you recommended may solve the logo problem and more important the memory "leak"....
What I basically want is to bring me Kaiser to its original status like from "out of the box"... because it's only 2 week old!!!!!
I'm hope you understand me problem.
Thanks you in advanced!
Shaico said:
First off all, thanks for the help. I appreciate it!
I must mention that I buy the original version in advanced. I just was curious to check the net version and it turns out that it's not so good... to such an extent that I ruin me Kaiser...
now let me be more specific with me problem because i m not sure I explain the problem clearly and I don't want to start a progress that I don't know how to do....
So, like I say, after I finish the install of the language pack, I had to clear storage in order to crack the license. But since that, every restart, appear the logo of the software company for 30 sec!!! Every restart!!!! Its make me crazy!!!! (The logo appear just before the HTC logo load. (It's appear with the rom and the radio version = R.G.D). But this is not the main problem!! The most important problem is that since the install, its keep say me that I'm run out of memory, and I m even didn't install nothing!!! This is bad!
So off Corse I'm try to do hard reset and even try to upgrade to WM6.1, but the cursed logo is still there!!!!
Now, after I try to explain the problem, I want to know if the solution you recommended may solve the logo problem and more important the memory "leak"....
What I basically want is to bring me Kaiser to its original status like from "out of the box"... because it's only 2 week old!!!!!
I'm hope you understand me problem.
Thanks you in advanced!
Click to expand...
Click to collapse
Do you have a storage card? I wonder if it flashed off the storage card? Anyhow, let's get busy...
Firstly remove anything you want to keep off the card and then format it.
Then flash the Hard SPL using the instructions here: http://forum.xda-developers.com/showthread.php?t=396922 (Second set of instructions in post #2).
Once, you have completed the flash, enter the bootloader before Windows Mobile loads.
Then, when you are in the bootloader flash a New ROM and Radio.
Hopefully that will remove everything that shouldn't be there.
Also, moving out of pof's thread. To a new one
Ta
Dave
DaveShaw said:
Do you have a storage card? I wonder if it flashed off the storage card? Anyhow, let's get busy...
Firstly remove anything you want to keep off the card and then format it.
Then flash the Hard SPL using the instructions here: http://forum.xda-developers.com/showthread.php?t=396922 (Second set of instructions in post #2).
Once, you have completed the flash, enter the bootloader before Windows Mobile loads.
Then, when you are in the bootloader flash a New ROM and Radio.
Hopefully that will remove everything that shouldn't be there.
Also, moving out of pof's thread. To a new one
Ta
Dave
Click to expand...
Click to collapse
I'm sorry, it didn't help! Or I didn't understand the mining of the post! so I follow the instructions and then what? Nothing change! It's all the same! I can't see any different! What else can I do? How can I erase all the data include all!! Data!! And start again and make it brand new again? Im just want this logo to go away!! How do I make my Kaiser new again with no foreign files that no came with me device from the factory! I want to Cray!! I can't help it any more! Please help.
Can you please help me live? Can we kindly chat in the messenger? I'm lost of me mind with all this posts and cant mange this alone!
Thank you in advanced!
Anyone can please help?
Hi, sorry for the delay.
The instructions in my last post should get you back up and running. You'll have have to read up on the wiki and the ROM Development stickies for more help.
I am at work now, and am pressed for time at the moment, have a look on #xda-devs chanel on FreeNode after 8-9PM (GMT) for me. I'll be able to chat then. (I am also on MSN, but I don't use it at home that often. I'll try and make an effort over the next few days.)
Ta
Dave
Hi, sorry if i open a new thread for problem soving, but i can´t find any solution for it and i really looked into the Dummies Guide! My SPL is 1.54 at the moment and i tried to put the 1.56 three times today, but it always gives me an "Update Error".
I go into the bootloader with the colors, and execute the HSPLWrapper_Blackstone_156OliNex.exe and follow it as needed. When it goes to the update Bar, maybe 30 seconds later it gives an Update Error on my computer (i think 262) and i have to take out the battery fom the HD. Then i can use the phone as usually, without problem. But how can i get the HSPL on it? AV is deactivated, sync isn´t lost. I seen somewhere anything about a protection in the forum, but i don´t remember where it was and in the dummies Guide it doesn´t say something about this.
The moderators at any time can close and delete my thread, if this problem was posted before, but as the forum is so big, i really couldn´t find anything.
Thanks
TMReuffurth said:
Hi, sorry if i open a new thread for problem soving, but i can´t find any solution for it and i really looked into the Dummies Guide! My SPL is 1.54 at the moment and i tried to put the 1.56 three times today, but it always gives me an "Update Error".
I go into the bootloader with the colors, and execute the HSPLWrapper_Blackstone_156OliNex.exe and follow it as needed. When it goes to the update Bar, maybe 30 seconds later it gives an Update Error on my computer (i think 262) and i have to take out the battery fom the HD. Then i can use the phone as usually, without problem. But how can i get the HSPL on it? AV is deactivated, sync isn´t lost. I seen somewhere anything about a protection in the forum, but i don´t remember where it was and in the dummies Guide it doesn´t say something about this.
The moderators at any time can close and delete my thread, if this problem was posted before, but as the forum is so big, i really couldn´t find anything.
Thanks
Click to expand...
Click to collapse
I guess you did not read the dummies guide carefully. Anyways,
1. Copy a file (Attached) to your SD card using your computer.
2. Go to that file in from your phone's file browser and run it,
3. This action would take you to the bootloader screen & would say SPL Version 1.07.Olinex.
4. Now attach your USB to the Phone. At the bottom of the screen you should see USB after a while (2-4 Sec).
5. Now Drag the ***.nbh file to the wrapper file (1.56 Olinex) from your Computer and your update process should start.
6. After sucessfully done this, Hard reset your phone (Twice Recomended)
Hope this helps.
If your problem is solved please acknowldege (Moderator please close this thread)
No need to panic, just follow tausifs advice and if you still cannot get it working, post your query in Dummies guide thread and myself or somebody else will assist you at their earliest convienience.
No need for another thread. Thread closed
Ta
Rick
I want to say thanks first for the help so far.
So I finally managed to hardspl but that was it unfortunatly.
Your dummies guide is quite good, but for someone not technical at all and normally not into handy programming etc???
HSPL3 is OK I have it.
As of HSPL4 I am stuck: I ran the the blackstone rapper with the nbh file, also ok
I do the hard reset and than I still have my old SFR etc on the phone (I have also the problem with the colours, but that is the least problem at the time)
I than tried to flash an other rom (Miri) and there I get error 240 (file open)
So I thought I do the hardreset again (bootloader showed than my old version, do not ask me why) I did everything again and I am stuck again.
After two days it starts being quite frustrating I must admit but i stay full of hope for your help
Thanks again
Reinhardbaer said:
I want to say thanks first for the help so far.
So I finally managed to hardspl but that was it unfortunatly.
Your dummies guide is quite good, but for someone not technical at all and normally not into handy programming etc???
HSPL3 is OK I have it.
As of HSPL4 I am stuck: I ran the the blackstone rapper with the nbh file, also ok
I do the hard reset and than I still have my old SFR etc on the phone (I have also the problem with the colours, but that is the least problem at the time)
I than tried to flash an other rom (Miri) and there I get error 240 (file open)
So I thought I do the hardreset again (bootloader showed than my old version, do not ask me why) I did everything again and I am stuck again.
After two days it starts being quite frustrating I must admit but i stay full of hope for your help
Thanks again
Click to expand...
Click to collapse
As I told you yesterday, please post your questions in the correct place. You have obviously read the Dummies Guide, so please post your question in that thread and do not start your third new thread. This thread will be closed as soon as the moderators find it.
If you have the colour problem your hspl was obviously not successful, are you sure that you did not try uspl, which may explain why your old spl is back?. In bootloader mode what spl is showing? It needs to show 1.56.Olinex (see picture)
ERROR [240] : FILE OPEN
When this error message appears, check whether the downloaded .nbh image is placed in the same directory as the RUUWrapper. If, for some unknown reason, you find that the ROM image is not located in the RUU folder, you have to download the RUU and retry again. Check that the contents of the folder is a CustomRUU.exe file and an .nbh file.
Click to expand...
Click to collapse
If you post in the right place I'll try my best to talk you through the process, it's really not that difficult.
Please post your query within Dummies guide thread and myself or someone else will answer your query.
Please try and abide by forum rules in future. No need for new thread. This has now been your 3rd unnecessary thread. Consider this your first and last warning. Failure to comply with forum rules will result in a temporary ban!!
Ta
Rick
p.s. Thread closed