On one of my friend's Tytn II,..there is this problem of no caller name/number displayed.
Whe he gets a call the display shows "incoming call" instead of say "John 99874646.."
What could be the cause ?
cheers.
i had that problem and cant see call history. solution to me was in NEW dialer i had vista dialer intaled it and it runs with no probs. good luck
Related
Hi,
I cannot find the option to turn on the feature, that the name of the caller is displayed, when it is in the phonebook. Right now, only the international number is shown whe somebody calls. What do I have to configure? Thx.
Regards Heinzelrumpel
No ideas ??????
WM5 onwards it is already there.
You have to feed the number for each contact as +<country code><areacode><Number>. For example +919896312345
Sometimes I get Incoming Call popup (the one with the caller picture) behind the bottom bar, just like it can't get focus from the OS. Soft reset resolves the issue but are there any ideas why is that happening?
I'm having exactly the same issue. I use native HTC 6.1 ROM.
So now we know it doesn't depend on the ROM since I am using native 6.0
Incoming Call not showing all info
Same problem here: Incoming Call not showing all info. But without solution.
I've had it quite a bit as well. I started using S2U2 for my full screen incoming call manager and it works great.
Hi,
if Diamond is locked and you receive a call “incoming call screen” is change (it is windows default incoming call screen).
It is possible to see Diamond “incoming call screen” even the prone is locked?
Thanks
P.S. Excuse my English
hi, I am not sure what exactly is your problem, but I personally use this program as replacement of the default call manager. it shows big screen with photo and few other information, not just the small one which I cannot read so easily.
Hello Sinmae,
I'm also trying to use Inesoft Address Book on my dimond however I have the following problem:
I've installed this program on my new HTC Diamond SPRINT, and I love it. However it conflicts with built-in dialer/callerid. On incoming call I see first the original caller id screen then after a second Inesoft one. On the call end it comes back to the original dialpad and not the Inesoft one. can I completly disable the built in dialer and caller id ? Do you have a solution?
Thank you in advance,
Leonid
leond said:
Hello Sinmae,
I'm also trying to use Inesoft Address Book on my dimond however I have the following problem:
I've installed this program on my new HTC Diamond SPRINT, and I love it. However it conflicts with built-in dialer/callerid. On incoming call I see first the original caller id screen then after a second Inesoft one. On the call end it comes back to the original dialpad and not the Inesoft one. can I completly disable the built in dialer and caller id ? Do you have a solution?
Thank you in advance,
Leonid
Click to expand...
Click to collapse
i have the same problem
inesoft Incoming call screen
inesoft Incoming caller id screen struggles to appear on top but the original caller id fight's back and so on.
aasa1111 said:
inesoft Incoming caller id screen struggles to appear on top but the original caller id fight's back and so on.
Click to expand...
Click to collapse
Install "Advanced config" program Open it and go to->Phone ->Phone skin: and disable it. Then soft reset. Your problem will gone forever
1. when some one call me a balloon will pop up as usual, but showing only the phone number, not showing the contact's name even though i got it saved in my contacts.
2. when using smart dialing(ver 2.5 build304260), after pressing call, during the call only numbers where displayed but not the name....and after the call, in call list only numbers were displayed but not the names...[if i call from contact list everthing is fine, both name and number displayed normally]
any help???
am using Hyperdragon's III lite rom (with xperia's dialer skin built in)
(been searching, and got exhausted!)
anyone???
help anyone???
I got a strange problem on my MDA Vario IV (HTC touch Pro). have got most of my contact numbers stored without the ISD code ..so typically looks like 07932******. Now when I receive a call it shows the contact name /or pic. But any text message shows only the number and comes up as +447932******. So I changed the contact number to read +447932******. But guess what ? the text display works fine, but the caller ID for incoming call now does not show the contact name..jus the number.. Anybody come across this?
Thanks
B
hi
well my friend, i am also experiencing the same problem you have described...exactly the same way you have described it...hopefully someone will advice us a it more on this issue. i changed roms but that problem is this here.