Hi, i'v got a problem. I tried change my digitizer and, when im done, now lcd doesn't work, because it is still white...:/ What can i do now? any solutions?
Thanks a lot
Check your connections. Pull apart and re-seat everything to ensure everything is hooked up good.
everything is fine :/ still white screen
Perhaps you zapped or damaged the LCD when you were working on it...
You could try replacing the LCD too -- but at this point I think I would send it to the professionals
HTC repair or someone like PPCTechs
Don't know if the screen set up is still the same. But when I replaced the screen on my Universal the wiring for the touchscreen was stuck down onto the lcd wiring, as they both shared common earths. Maybe worth a check before spending more cash?
i have the same problem, the screen was working fine before i replaced the new digitilizer and now its just white but i can hear the tablet playing so it must be the screen.i checked all the wiring 4 times now! any idear???
:crying:
Slide the phone open and apply some pressure near where the angle of the opening is (back of the LCD below the SIM, where there is a bar). I had the same issue and this fixed it.
Hi everyone!
Sad thing happend with me, 4 days ago i fell into a river and sadly ma diamond was in the pocket. I dryed it for three days, turned it on, everthing else works, besides the screen light. So i dissambeled the phone to bits and pieces, only i didn't took the LCD out(read it from somewhere that you can't put it back on afterwards so it will work). I reassambeled it and still same situation. If you look it from a angel you can see the icons and even touchscreen works. Only problem is still the backlight. So is there something i can do to make the backlight work again or i have to buy a new screen and is it hard to swap the screen ?
Hi,
Not sure if you will need to replace the screen, if you can get to the power settings you can see if the backlight has been manually turned down. If this fails and a screen replacement is required i will tell you how easy/difficult it is once i have replaced mine, due to unfortunate circumstances.
yeah, i got into the power settings, everthing is okey there like it should be , so i have to change the screen. Is there some kind on intrcutions for changing it? it would help me a lot
I have searched for solutions for the past 2 days but cant find one, if i missed it or this post is redundant , i apologize in advance.
Now my tilt is driving me crazy. It started last week when The touch screen wasnt working, but i fixed it by doing a couple of soft resets. then all the sudden, everytime i slide my keyboard out, the touch screen would stop responding. this went on for a day, then yesterday, when i tired to use the keyboard, the screen went blank, like the light died or something. but when i put it back on portrait, the screen would light up again.
A few moments later, the touch was responding, tried to use the keypad then the screen went blank..tried soft resets about 5 times and uninstalled all recent added programs (skyfire) ..finally the screen was working but the touch still wasnt working.
So this morning, i had the bright idea to do a hard reset....dumbest idea ever cos now its stuck at the screen where i have to "tap the screen to set up your wm device" and guess what..the touch screen isnt responding
plz i really need help with this. all so , i have a broken tilt.., well lcd screen is cracked...can i try to dismantle both tilts and replace the screens?
Ok, i used Code Factory's Remote screen alignment to bypass the alignment, but if i cant use the touch screen or the keyboard, the phone is pretty much useless for sending any information or making calls..is there a way to fix this?
I have had this same issue with my tilt. I could use the scroller on the left side of the unit to navigate but no touch screen. Both times that this has happened to me I removed the screen protector that I had on and restored a backup that I had on my storage card (I run a backup weekly). This has always fixed my issue. You could try another hard reset, not sure if that will help but do you get any lights on the keyboard when you slide it open? Is your tilt less than a year old because there is a manufacturer's warranty too.
Jim
when i slide the keyboard, i do get lights on the keyboard but not on the screen...it just goes dead..but when i slide it back in, the screen comes to life.
I cant do another hard reset cos i have to input the "1,2,3,4" code.
Also , the phone just got out of the 1yr warranty this month...awesome
I want to buy a replacement screen with a new digitizer but i need to be sure that is the problem.. ive searched for this keyboard problem but still have no answers
Now I'm having the same issue, touch not responding. I first noticed it about two days ago, when I slide the keyboard out, I could type just fine, but when I went to send the message the touch screen wouldnt work, so I'd close the keyboard and it would work. well yesterday it stopped working all together, so i used my d-pad and did a sprite restore and it started working again. But then On my way home i hit the lock button, and it stopped working after that, and I couldn't get it unlocked. I used the inner soft key to hit the first part of unlock, but then I couldnt ever figure which button to hit to get the on screen part of the unlock. So I had no choice but to do a hard reset, and just like highoct now I'm stuck on the stylus setup , and the touch still doesnt respond. does anybody esle have any suggestions ? Thanks in advance.
You can use the Code Factory's Remote screen alignment to bypass the alignment.
If the touch screen is the only problem, you can do one of two things if you are no longer under warranty;
1. Fix it yourself. You will have to buy a new Lcd screen with new digitizer at ebay and use this site http://www.pdacenter.ru/razborka/razbor_htc_kaiser/ to open up your tilt and replace it
2. Send it to a repair shop, I had two tilts and sent the one with the broken screen to www.missionrepair.com got it back in a within a week, $89.00 plus shipping
here is the link : http://www.missionrepair.com/Mission_Repair_AT_T_Cell_Phone_Repairs_and_Upgrades_s/321.htm
I still have the same tilt with the original problem..havent found a solution yet
Oh yeah, I did manage to do a hard reset again, but now the screen is just white. I can hear the sound of it booting up but it still has a white screen. I tired going to the Bootloader screen ( Camera and power at the same time)...still have the white screen. I believe its a hardware problem but i don't know what it is...any ideas?
Ok now I've done a hard flash, using the same HTC kaiser rom 6.1 and it fixes the problem for a little bit, until the first time I slide out the keyboard , then the screen stops working again, any suggestions ?
iPhone 3G Screen Repair...finally an affordable answer
If you are reading this, you are most likely in the same dilemma I was in. I dropped my phone and picked it up only to find out that the glass screen was cracked. I took my broken phone to apple and found out it would cost me $199. I then was told about iPhone 3G Screen Repair. They offered the iPhone 3G glass screen repair for only 69.99. They repaired my phone the same day they received it. I was very happy with the repair!
Chill0987 said:
If you are reading this, you are most likely in the same dilemma I was in. I dropped my phone and picked it up only to find out that the glass screen was cracked. I took my broken phone to apple and found out it would cost me $199. I then was told about iPhone 3G Screen Repair. They offered the iPhone 3G glass screen repair for only 69.99. They repaired my phone the same day they received it. I was very happy with the repair!
Click to expand...
Click to collapse
Sounds like a plug for your website to me... Last I checked this wasn't an iPhone site.
Chill0987 said:
If you are reading this, you are most likely in the same dilemma I was in. I dropped my phone and picked it up only to find out that the glass screen was cracked. I took my broken phone to apple and found out it would cost me $199. I then was told about iPhone 3G Screen Repair. They offered the iPhone 3G glass screen repair for only 69.99. They repaired my phone the same day they received it. I was very happy with the repair!
Click to expand...
Click to collapse
Does this look like an apple website? did i say i had an iphone? GET OUT OF HERE!!!
Ninety Four said:
Sounds like a plug for your website to me... Last I checked this wasn't an iPhone site.
Click to expand...
Click to collapse
And thats his only post, its spam. jerk him outta here
Tilt Touch Screen
highoct said:
You can use the Code Factory's Remote screen alignment to bypass the alignment.
If the touch screen is the only problem, you can do one of two things if you are no longer under warranty;
1. Fix it yourself. You will have to buy a new Lcd screen with new digitizer at ebay and use this site http://www.pdacenter.ru/razborka/razbor_htc_kaiser/ to open up your tilt and replace it
2. Send it to a repair shop, I had two tilts and sent the one with the broken screen to www.missionrepair.com got it back in a within a week, $89.00 plus shipping
here is the link : http://www.missionrepair.com/Mission_Repair_AT_T_Cell_Phone_Repairs_and_Upgrades_s/321.htm
I still have the same tilt with the original problem..havent found a solution yet
Click to expand...
Click to collapse
I know this thread is a bit old but was searching d forum for possible solutions cos yesterday i developed the same exact problem on my kaiser for no apparent reason!..flashing it hasnt helped and now im stuck on the wm setup screen..when u say u still have the same tilt with the original problem do you mean that the repair was unsuccessful? have you tried reparing it yourself? Thanks
I just started to have the same problem, it started out with the touch not responding (which a few soft resets fixed) and now the whole screen doesn't function unless i slid out the keyboard or if i jiggle it around and open it a couple of time i can usually find a spot that allows the screen to function with the keyboard closed. If i leave it in this position for about an hour the touch starts responding again, wtf. This is very inconvenient because as soon as you move the screen even just a little it will take me like half an hour to find the position which allows the phone to function.
grayfoxmg1 said:
I just started to have the same problem, it started out with the touch not responding (which a few soft resets fixed) and now the whole screen doesn't function unless i slid out the keyboard or if i jiggle it around and open it a couple of time i can usually find a spot that allows the screen to function with the keyboard closed. If i leave it in this position for about an hour the touch starts responding again, wtf. This is very inconvenient because as soon as you move the screen even just a little it will take me like half an hour to find the position which allows the phone to function.
Click to expand...
Click to collapse
same thing happened to me 3 days ago. touchscreen has just stopped responding.
it still worked when i slided my keyboard out, but only when it was out. then i realized it won't work at all (!) after soft reset. however, i could make it work again like that when i did the soft reset with the keyboard out. weird.
i tried searching, and decided to make a hard reset, flash a new rom, etc, etc., but no more touchscreen. at all. the device doesn't feel any touch in any case. nothing. i bypassed the beggining tap here with the storage card trick. (i've read it somewhere on the forum).
now i can only use my kaiser with the hw buttons, the keyboard, and that's it. no touch. really weird. please if anyone has any updates, solutions, anything, post. sniff sniff
mine doesn't have anything on the screen unless i slide it out, if i have it closed anymore, it just doesn't work at all.
try this:
ive just replaced my barely functioning lcd by myself, after living with it sometimes registered the stylus jumping around when i used the stylus. but before you change your lcd, here is a couple of tips for you guys:
1) try sliding out the keyboard. hold one finger in the middle of the keyboard and another on the back side of the phone, and squeeze hard, but careful. it might be that the flat cable between the screen part and the main part has loosened a bit from its socket, this could help it back in.
2) try sqeezing the hang up button hard. this might help the lcd-cable correctly back in its socket if it is loose.
im saying that this MIGHT help, if youre lucky. most likely you have to open the phone and squeeze the connectors back in yourself, or actually change the entire lcd. anyways, let me know what works for you!!
se1988 said:
ive just replaced my barely functioning lcd by myself, after living with it sometimes registered the stylus jumping around when i used the stylus. but before you change your lcd, here is a couple of tips for you guys:
1) try sliding out the keyboard. hold one finger in the middle of the keyboard and another on the back side of the phone, and squeeze hard, but careful. it might be that the flat cable between the screen part and the main part has loosened a bit from its socket, this could help it back in.
2) try sqeezing the hang up button hard. this might help the lcd-cable correctly back in its socket if it is loose.
im saying that this MIGHT help, if youre lucky. most likely you have to open the phone and squeeze the connectors back in yourself, or actually change the entire lcd. anyways, let me know what works for you!!
Click to expand...
Click to collapse
well, i tried both tips, but they didn't work. i'd like to say a big thanks anyway!
then i grabbed the kaiser service manual and took my device apart into pieces. i reconnected pretty much all the cables and stuff, but still no touchy. any further ideas?
you should try replacing the screen. im happy to say that this screen from this seller on eBay worked for me: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=250539984183
look here for dissasembly video: http://www.fonlogix.tv/tiltlow.wmv
(to save it to desktop right click link and "save target as")
thanks for your help, i've just ordered a new screen! phew, i hope it's gonna work
Well ive had my phone for a while with hyperdragon iv iolite working completely fine without any hardware or software issues for months. Today i took out the battery of the phone, and put it back in and turned it on, but when the phone turned on, the touch scrren is not responding to anything. everything works fine with all the buttons and keyboard, but the touchscreen isnt working. What could have gone wrong just by taking out the battery. I also havnt dropped or damaged the phone in anyway so i dont see it being a hardware problem. Thanks. I really need help
I have heard of people who has been able to solve this problem by hard resetting the devise. I have had not such luck....comes to be that from sliding wear and tear the connector to the screen gets damaged. My screen is completely disable, I found someone that was able to buy a second hand phone on ebay and was able to switch the connector. Looks like to much of a hassle to me, so Im sticking with this until I switch phones.
Hello, I am a true noob so please forgive me if I sound dumb.
I had a broken screen so I bought a new one on Ebay. I changed it perfectly, it looks good but now when I touch the screen it acts like I touched the top left corner (in portrait)no matter where on the screen I touch (so it opens up the "Start" menu). In landscape it acts like I touched the top right so it opens up the drop down menu with all the running programs.
I would really appreciate some help. I try re-aligning the touch screen but it does not recognize any touches at all. I have to soft reset the phone to get out of the re-align program.
I don't want to hard reset because I have read many cases where the phone gets stuck in align program as it is trying to setup and they have to install remote access or something to get around it.
I would like advise on whether it is the new screen or the phone. Is there something I can check for inside or should I send the screen back for a replacement.
Thank you for your help.
Having replaced the touch screen in a Palm with success, I would say that...
You either have a problem with the connector for the screen, recheck the connection
Someone sold you a bad screen.
Something else is wrong with the device.
At this point I don't know that in your position I wouldn't do a hard reset. What is the worst thing that can happen? The device is already broken in it's current state.
Good luck.
Thank you
Thank you very much for your help. I will try the connector. if it does not look damaged then I will return the screen.
Did you replace just the screen itself, or the screen and the digitizer? More than likely your digitizer is broken aswell. If you replaced them as a set, request a new one from wherever you got it, and if you just replaced the LCD, then you need to buy a digitizer aswell.
ashasaur said:
Did you replace just the screen itself, or the screen and the digitizer? More than likely your digitizer is broken aswell. If you replaced them as a set, request a new one from wherever you got it, and if you just replaced the LCD, then you need to buy a digitizer aswell.
Click to expand...
Click to collapse
Well, I only received the screen. I cant figure out where the digitizer is on the tilt so I don't know if I changed it or not. Does any body have any picture??
I think I read somewhere that it all comes as one piece(the screen and digitizer), but I can't confirm it.
Indeed they most of the time do come as one peice, so if your connection is good on the mobo, then I would say that the digitizer you recieved is bad. The digitzier is the super thin peice of glass that covers the LCD screen.