Database Develop

kaiser stuck on tri screen is it a brick???

i hope this is where i should post this.
whilst using my phone it froze,so soft reset was done then it went into tri screen
my kaiser wont go out of tri screen.i have this on screen.
kais130 mfg
spl-1.0.olipof
cpld-8
after trying hard reset and soft reset it wont pass this screen,it loads straight back to bootloader mode.i had duttys 6.1 rom on and nikis radio.
is there a solution to this problem.all was fine until this.ive searched all over for the past week and i cant seem to find a solution,so a little help is called for.id appreciate any help if possable and thank you in advance

Are you sure that your camera-button isn't stuck? Try pushing it hard few times, and then boot again.

Try flashing an official rom onto it while on that screen?

hi tried new rom and camera button isnt stuck,it seems like theres something wrong with spl-1.0.olipof.after installing new rom it boots straight to tri screen.can olipro be tacken off.just thinking of other things to revert to normal.when soft reset done it goes straight to tri screen

Try HardSPL
Why not flash it with a different SPL - like any of the HardSPLs such as Jocks:
http://forum.xda-developers.com/showthread.php?t=396922
and then flash with a new rom, suitable to that SPL?
rgds, MN

Fyi, this issue is being discussed in lots of threads @ ROM Development... I do have the same problem.
http://forum.xda-developers.com/showthread.php?t=402562
http://forum.xda-developers.com/showthread.php?t=371154&page=9
... and this one being the most recently updated:
http://forum.xda-developers.com/showthread.php?t=393337&page=29

Just to point out that the problem is solved (I think) - read here -> http://forum.xda-developers.com/showthread.php?p=2415437#post2415437

[SOLVED] Noob needs help! Is my qtek9100 a brick?

Hi!
this is my first post here, so sorry for my bad english or mistakes
i bought a qtek 9100 on ebay, and i'm wondering if it's a brick or not. i received the device 3 days ago. during this time i read through a LOT of threads here, tried a few things and nothing works.
here is some info:
- the phone is a qtek 9100 without branding
- the IPL is now 1.01 (i flashed "CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE" successfully)
- the SPL is 2.18 (because of the missing suffix ".0001" i guess it's a G3)
- GSM is 01.12.10
- OS is 1.5.4.2
- when i start the device (without any button pressed) it stops at the splash screen (which was a qtek logo before flashing, and is now this picture with a beer, that says "some things last forever" )
- i can get into bootloader screen (color screen) by holding camera button while starting
- in bootloader screen a small "USB" appears when i connect cable to usb on pc
- when i press communicate and voice buttons (on the sides) while starting, the "Press send to restore factory default" screen appears, but pressing send prints out "Format FAT Partition Format is Failed"
- the device gets recognized by windows ("Mobile Device" appears on my computer)
- ActiveSync 4.5 does not connect to device, not even as guest.
- when i hit "Connect..." in ActiveSync's connection settings, nothing is found
("Allow USB Connections" is ON)
- the device is CID-locked ("FF" state in Mtty 1.42)
- i can't unlock CID, because i can't get "EnableRapi.cab" onto the device without ActiveSync connection
Ok, these are basically the things i know now. The problem is that i never saw any other screen then the "HTC" boot screen, the "Qtek" splash logo (the one with the clouds) before i flashed with custom ruu wwe, after that i see the new splash logo, and i can get into bootloader (color) screen. I never saw any windows mobile running on this device! I could never establish a connection with ActiveSync!
So i hope that someone here on this nice forum can help me get this device to work (WM5 would even be enough right now) or at least give me a hint!
Thanks in advance!

Put the phone in bootloader mode and flash back to the original ROM.

since i bought it in ebay i don't have the original rom of this device.
but i found "233309-qtek9100_2180707_21807109_20710_qtek_ger_ship.exe" through google, which seems to be an original qtek rom (version 2.18). shall i flash this one?

You can find in the Wiki the latest official roms of every brand for our Wizards .-

ok, thanks.
i found one (Qtek GER 2.18.7) and flashed it. the process was successfull, now the IPL/SPL is both 2.18 . But the device still doesn't start and stops at the splash screen (which is now the original qtek splash again). I can still get into bootloader mode and hard reset results in "Format is failed"! No ActiveSync connection either... how should i proceed now?

i basically narrowed it down to these two problems:
- the splash screen freezes
- hard reset error "Format is failed"
( IPL: 2.18, SPL: 2.18 )
can't anybody help please?
i'm freaking out about this

With everything i’ve read the only people who’ve had any success had CID unlocked devices.

ok, i think that too for what i've read so far...
is there any other way of CID unlocking except lokiwiz (can't copy enablerapi.cab without activesync!)?
would this imei-check service that i've read about work in this case?
meanwhile i've also tried something with mtty (r2sd all) but doesn't work -> "didn't get proper security level"
is this also because of the CID lock? i tried to find out the right password to enter in mtty, but found nothing that worked...
does anybody know the correct password?

I couldent CID unluck my 9100 with lokiwiz so i did it 5min ago with Wizard Service Tool (ha to reboot my computer).

I'm having the exact same problem,
except I can't flash any other ROMS so I'm stuck looking at this incredibly frustrating beer picture, with "some things last forever".
Does anyone have any further ideas?

Look up the orignal rom on the wiki, get into bootloader. And flash it back.
Jodda said:
I'm having the exact same problem,
except I can't flash any other ROMS so I'm stuck looking at this incredibly frustrating beer picture, with "some things last forever".
Does anyone have any further ideas?
Click to expand...
Click to collapse

Jodda said:
I'm having the exact same problem,
except I can't flash any other ROMS so I'm stuck looking at this incredibly frustrating beer picture, with "some things last forever".
Does anyone have any further ideas?
Click to expand...
Click to collapse
Hi Friend!
I have the same problem with my Qtek9100!
Any ideas? have you solved your problem?
I have the frustrating beer picture
Please help me.
Very Thanks

Like I sad before
Get into bootloader, flash back the original rom and try again.
mizobuchi said:
Hi Friend!
I have the same problem with my Qtek9100!
Any ideas? have you solved your problem?
I have the frustrating beer picture
Please help me.
Very Thanks
Click to expand...
Click to collapse

I put the original rom.
But... the problem is the same.
when I started the device (without any button pressed) it stops at the splash screen (which has a qtek logo before flashing)
- i can get into bootloader screen (color screen) by holding camera button while starting, I installed the original and others rom who days before works perfectly... Now... this stopped at splash screen
- when I tryed to format.. = "Format FAT Partition Format is Failed"
Any idea?
I have tried this : http://forum.gsmhosting.com/vbb/showthread.php?t=332143
but... without success.
Could you help me, please?
Very Thanks

i'm still stuck with the same problem with hang up on qtek splash screen, too!
i have IPL 2.18 and SPL 2.18 and i can get in boot loader screen and connect with usb. (but no activesync connection!)
formatting doesn't work either.
does anybody have an idea how to solve this?? it's frustrating... i've tried almost every guide here on the forums.

same proplem here with
ipl 2.16
and spl 2.16

I used this to fix this problem
Hi i had the same problem the other week, installed a dodgy app, went to do a hard reset and wouldn't do a hard reset format failed. Tried updating rom everything worked ok until you booted it up. Wouldn't go past second splash sreen. After a few hours of trawling round i found this thread.
http://forum.xda-developers.com/showthread.php?t=276963&highlight=format+is+failed
worked for me. Hope this helps you out.

Problem in connecting to my PC
Hey ,
I just bought a qtek 9100 a day before ... I tried to connect it with my computer.. instead of connecting my battery gets charging well can u plz help me out !
is there any software that i should install in my pc in order to get it connected to my PC...... please help me fast ! Lot of work is pending !
Thanks
Salman

Ok guys, I finally have this SOLVED.
My QTEK 9100 is working fine now!!!
I'm so happy with it right now
Since nothing I tried worked, I went to imei-check.co.uk and got my phone completly unlocked! It only cost me about 11€ and since it works now I have to admit that it was worth it (no advertising). After the unlocking was done I could do the "r2sd all"-method (Tool: MTTY 1.42) using a miniSD card. You can find a good tutorial on this board somewhere. After that everything was just fine...
-> I never saw it working and Hell Yeah: This baby just kicks a$$ !!! (although it's kinda 'oldschool' these days )

Stuck on bootloader screen!!! Help!!

I've been waiting for hours for someone to help me and I searched and searched, I can't find any help!!! I have to go to work soon and I've been on this screen since 7:30AM EST!
Looks like I'm stuck at the boot loader screen and it goes back to it when I do a soft rest. I can't do a hard reset since I can't turn off the phone.
I think it's the bootloader screen.
Says RUUNBH on the top right corner and the screen is red, green, blue and white which these codes or whatever.
Took the battery out for a few and it went right back to that same screen.
Can someone help me bring back my Rhodium to stock???
EDIT: I might of posted this in the wrong section. Should this be in Rhodium General?
*UPDATE*
ark666 found the stock rom for T-Mobile HTC TP2 and I did a flash to get it back! Thank you so much ark666!!!

Flash stock rom.

I have no idea on how to do that, I searched how-to's but I can't find any full instructions or where to get the stock rom for T-Mobile HTC TP2.

This is the worse ever!!! Somebody please!!!
Isn't this the best site for things like this?

Try a manual hard reset? The instructions should be in your manual.

It says while the phone is off to HOLD SEND/END key with the power until the message comes up. The phone wont turn off unless I take out the battery for me to do a hard reset.
EDIT: I took the battery out then put it back in. The phone is now off, I hold the buttons and did the hard reset. It went right back to the boot loader screen.

hi,
what happend after you hard reset the device?
regards,
twisted

Asked me to press the VOL UP button to reboot. I did and it went right back to the boot loader screen. A flash happened on the screen when I try a soft reset and it says really quickly!..."NO IMG FILE" then it goes back to the 4 color screen.
EDIT: Image below on how my screen is since 7:30 AM EST!!!

on some device, active the RUU, connect it to PC & press soft reset button (the one in side the battery cover).
don't know if it help, just try that
good luck

Thanks for the reply, but that was the first thing I tried. Looks like I will have to go to work with no phone! This is crazy on how this can't be resolved.

Looks like you've basically erased the flash I'd say...
If you can get the t-mobile image, then try flashing that back to the device... If you connect a usb cable to your device, at the bottom, where it says serial it'll change to usb...
Or, if you have a goldcard, maybe try installing another image. But I'd say you're best to install the t-mobile image if you can get one?!

Ok so where can I get an image that will work on my phone? I also will need instructions on how to do it properly.

HeavyComponent said:
Ok so where can I get an image that will work on my phone? I also will need instructions on how to do it properly.
Click to expand...
Click to collapse
Where are you from? Can you find the rom on your tmobile site?
Or, creat a goldcard, copy the RHODIMG.nbh into the root of the card and try flashing that...?
As far as I know, your device is not bricked, you simply need your original supplier rom...

I replied to the PM (basically do set 16 0 command in mtty)
but I see your photo now - you have 0.85.1000 SPL? that's mfg SPL so if "set 16 0" did not help (you didn't describe what you did to the phone when this happened), you can just take any official rhodium ROM and flash it
sorry if I misread your photo... quite blurry

Ok that's my main problem that I've been having. Where can I get an official Rhodium ROM and how do I do a flash? I've been searching all morning.
And yes 0.85.1000, that's what it says on the screen.
I tried to this ROM...Link: http://forum.xda-developers.com/showthread.php?t=548546
Did the goldcard, but I think I did it wrong. I added the RHODIMG to the SD then tried to update my TP2. That's when I got an error saying it's not for PDA and how I need to update my utility.
I got the steps to do the goldcard correctly, I just want to take another shot at updating this ROM.

lovelldr said:
Looks like you've basically erased the flash I'd say...
If you can get the t-mobile image, then try flashing that back to the device... If you connect a usb cable to your device, at the bottom, where it says serial it'll change to usb...
Or, if you have a goldcard, maybe try installing another image. But I'd say you're best to install the t-mobile image if you can get one?!
Click to expand...
Click to collapse
hard reset doesn't erase the OS image.

HeavyComponent said:
Ok that's my main problem that I've been having. Where can I get an official Rhodium ROM and how do I do a flash? I've been searching all morning.
Click to expand...
Click to collapse
see my PM first, maybe set 16 0 will be enough.
is your SPL version really 0.85.1000? how did you get this phone? what happened when it got stuck on bootloader screen?
as for flashing, see xdadev wiki on rhodium.

Ok, will try what you PMed me. Brb!
It says 0.85.1000 on the screen so I guess so and I got it from T-Mobile. Ordered it through Customer Service.
post #15 has been updated to let you know what I was trying to do.

HeavyComponent said:
Ok, will try what you PMed me. Brb!
It says 0.85.1000 on the screen so I guess so and I got it from T-Mobile. Ordered it through Customer Service.
post #15 has been updated to let you know what I was trying to do.
Click to expand...
Click to collapse
then the set 16 0 will work just fine
weird the rom didn't work though

I have just flashed the 6.5 rom which you flashed
It does change the spl to 0.85 and i have the exact the sameimage which you have shotted during the flash process. But the process of this rom's flashing has two stage, it will restart after first 10% and show up the image which you shotted and upload, and continue afterwards. i guess ur goldcard has the problem so it stops and stucked there. Try other sign roms would be a better solution.

Kaiser bricked nothing worked yet.

Hi.
today i bricked my kaiser when i tried to install a dutty's rom
been trying to get this fixxed for over 5 hours. nothing worked out.
used kaisdiag.nbh from h ttp://forum.xda-developers.com/showthread.php?t=420683
in both suggested solutions my kaiser wont go further then the Loading page. ( waited atleast 10 mins twice without any success)
used some other RUU installs while in the tricolour screen:
ahmedfikry wm6.5 23549 Tilt UC light rom
KAISER_WM65_OS23547_PP12MB_Sonblack05
RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship
RUU_Kaiser_HTC_WWE_3.02.405.0_radio_sign_25.70.30.05_1.58.26.20
Ruu_Signed_Duttys_WM6.1_5.2.19700_Hybrid_V2_1_64.08.21_CubeV2_ <== the one wich bricked my phone
Ruu_Signed_Duttys_WM6.1_5.2.19700_Hybrid_V2_1_65.14.06_No_CubeV2_
RUU_Kaiser_TMO_UK_3.31.110.3_radio_sign_25.83.40.02_1.70.18.02_Ship
some other topic sugested to use MTTY.
but that probram says: usb port cannot open.
long story short: im desperate.
can any of u please help me fix my phone ?
its an MDA vario II. model Kais130 P/N 99hcy063-00
thanks in advance.

i'm no expert at recovering bricked phones...
but what i understand is that IF you have a hard SPL (which hard SPL do you have?), then you should be able to recover your device from nearly any situation.
try this...if RUU is not working well, try to flash using the SD card method.
also, try to flash a stock ROM (using RUU as well as using the SD card method). let us know what happens.

Try putting your phone into bootloader, ( press and hold power and camera buttons while doing a soft reset ) once it is in the " tri-color " screen, let us know what it says on the screen.

thanks for your time and the fast response, to both of you.
@#1
i used Pofs hard spl.
and as mentioned above i tried both the RUU way and with my micro SD card.
the SD way only shows me the 'Loading' screen. over and over.
and with the RUU i get several errors. connection errors at 0% and connection errors some later.
some roms just say they wont work on my phone.
and others just reboot my phone.
@#2
i think my phone gets to the bootloader all the time. cause i c no difference when resetting with camera and power button on.
its the tri color screen with the folowing information that shows up:
RUUNBH
Kais130
SPL-1.56.0000
CPLD-8
serial/USB
______________________
the serial shows up when the phone is not connected.. and the USB shows up when its attached to my pc with usb.
Any other suggestions ?
Thanks in advance .

You don't have hard-spl you still have a stock, flash the stock ROM of your carrier from bootloader.
Then follow the noobs guide to flashing.

Thx guys my phone is working like it used to be.
downoaded the original rom from t-mobile again. and again.
now got one wich is working.
thanks for your help.
i was about to throw the brick trough the window.

white screen after Jtag

at first, sorry for my bad english and my long thread
I've a bree100 simlocked and I tried to unlock it by "HTC_Hermes_SIM_CID_Unlock_v3a" but when RUU tries to flash the phone restarts and the bootloader goes down, of coarse it can't be connected to usb again.
So I tried Jtag from the forum after some work I can flash "iplsplbreeze.bin" and the phone can enter bootloader again BUT WITH NO TRI-COLOR just white screen THEN I've tried "TeraTermPro" which tell me that my phone is "QTEK_Z12" then I flashed it with the ROM "852727-mteor_upgrade" from the upgrade wiki as it's the only one that the phone accepts and now it can boot in normal mode but still white screen, I've checked the display and the main board for hardware errors but it seems to be good
PLZ tell me what to do else ?
I can't flash any other roms as I can't see any thing to make SSPL
Is thre any idea?
thanks'
dr. Wael Mossa

can anyone answer me???

thank you all for not answering
I solved my problem

hey there... don't anger... nothing has gone here for a while... so no one can answer if no one is watching this here!
can you tell what you did that you get the white screen of after jtag ?!
and why did you jtaged?! had you got no CID ?!
HTCSF kEØ(HTCE

I encountered the same problem, tried a few "iplsplbreeze.bin", including the self-made​​. Prompt solution for the switching device in the "tri-color" mode?