i hope this is where i should post this.
whilst using my phone it froze,so soft reset was done then it went into tri screen
my kaiser wont go out of tri screen.i have this on screen.
kais130 mfg
spl-1.0.olipof
cpld-8
after trying hard reset and soft reset it wont pass this screen,it loads straight back to bootloader mode.i had duttys 6.1 rom on and nikis radio.
is there a solution to this problem.all was fine until this.ive searched all over for the past week and i cant seem to find a solution,so a little help is called for.id appreciate any help if possable and thank you in advance
Are you sure that your camera-button isn't stuck? Try pushing it hard few times, and then boot again.
Try flashing an official rom onto it while on that screen?
hi tried new rom and camera button isnt stuck,it seems like theres something wrong with spl-1.0.olipof.after installing new rom it boots straight to tri screen.can olipro be tacken off.just thinking of other things to revert to normal.when soft reset done it goes straight to tri screen
Try HardSPL
Why not flash it with a different SPL - like any of the HardSPLs such as Jocks:
http://forum.xda-developers.com/showthread.php?t=396922
and then flash with a new rom, suitable to that SPL?
rgds, MN
Fyi, this issue is being discussed in lots of threads @ ROM Development... I do have the same problem.
http://forum.xda-developers.com/showthread.php?t=402562
http://forum.xda-developers.com/showthread.php?t=371154&page=9
... and this one being the most recently updated:
http://forum.xda-developers.com/showthread.php?t=393337&page=29
Just to point out that the problem is solved (I think) - read here -> http://forum.xda-developers.com/showthread.php?p=2415437#post2415437
Related
Any ideas? i get the cingular splash screen... gives me this info
IPL 1.08
SPL 1.08
GSM 01.09.11
OS 1.8.11.1
then it vibrates... then the screen goes dark.. sometimes the screen comes back on.. then goes off again... and that's about all it does...
any ideas? tried soft reset.. (didn't do anything.. durh) attempted hard reset... that also didn't do anything....
any help you can provide would be greatly appreciated...
Moose
were u trying to flash rom before this happend? are you able to get into usb mode? if yes try reflasing ROM, get cingular one.
No... it was flashed back to cingular so the phone could be sold by a friend and I thought it worked ok.. at least according to him... however that appears to not be the case... I am able to get into usb mode... I think... that's the multi color screen where it says usb at the bottom left when it's hooked up to my pc....
i'm fairly sure it's cidunlocked.. however i'm not positive...
I recently upgraded to the official 1.93 WWE ROM (and new hard SPL), and now my screen flickers a lot when the phone is switched on. (The flickering starts at boot-up when the red writing appears at the bottom-right of the screen).
I have been able to solve it so far by pressing the power button twice to switch the display off and back on again, but wondered if anyone else had experienced this and could suggest a more permanent fix?
Thanks,
Neil
Most likely who hasnt experienced this.....lol
Anyway, when you get this after a reset, just turn on and off the display and all goes back to normal.
You need to flash another hard spl. The issue is caused by an outdated spl not being compatible to your lcd screen. Try hard spl 1.37 found here:
http://forum.xda-developers.com/showthread.php?t=400950
I want to flash
_QMR_RUU_Diamond_HTC_WWE_1.93.405.1_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship
to my UK Vodafone Diamond which has SPL 1.37 from the factory.
Which Hard SPL should I use - 1.37? Signed or unsigned?
djvw said:
You need to flash another hard spl. The issue is caused by an outdated spl not being compatible to your lcd screen. Try hard spl 1.37 found here:
http://forum.xda-developers.com/showthread.php?t=400950
Click to expand...
Click to collapse
Thanks! I tried searching for "flicker", but got too many results and didn't find that thread.
i have the flickering screen too, i want to try this method but my activesync does not work. i try a hard-reset and now the device ask me to insert Getting STarted Disc to install synchronization software which I did. it still doesn't work. anyway to do this?
Thanks
i have the same problem i flashed the 1.93 hard SPL and still nothin... anyone know the problem?
i did managed to get the flikering out... flashed hard spl 1.38!
I want to try flash HardSPL but my USB port doesn't work, is there anyway to do this?
hello!
I am new here and i got one big problem.
So please help me!
I tried to flash my tytn II with this rom(ENDED- 28/V/2009 Anryl WM⑥.⑤ 21725 FINAL ULTIMATE(101RAM) -ENDED- ), but when i finished the flash, my phone want to boot. It stops on black screen and show "HTC"
If someon know how to fix it, please help me!!
R 1.27.16.21
G 22.52.88.13h
D 3.34.00.00
did you flash jumpspl and hardspl first?
Yes i did.
I did everything like it said in http://forum.xda-developers.com/showthread.php?t=433835 and my phone is stuck in bootloader. So how can i reflash it? i tried to flash it again with sd card but when i use power + camera + stilus to get bootloader, in a second there is a white screen where is written that there is no image, and it go back to three color screen mode, and in the bottom is a white screen where is written "serial"
When i try to flash it with activesync there is an error 262. I spend a lot of time reading many posts here, but i did not find enything what help me.
Any sugestions?
Thanks!
Bro, did you solve it? please let me know. Same issue and as described in the faq's tried using MTTY but that one also does not connect.
Hi.
today i bricked my kaiser when i tried to install a dutty's rom
been trying to get this fixxed for over 5 hours. nothing worked out.
used kaisdiag.nbh from h ttp://forum.xda-developers.com/showthread.php?t=420683
in both suggested solutions my kaiser wont go further then the Loading page. ( waited atleast 10 mins twice without any success)
used some other RUU installs while in the tricolour screen:
ahmedfikry wm6.5 23549 Tilt UC light rom
KAISER_WM65_OS23547_PP12MB_Sonblack05
RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship
RUU_Kaiser_HTC_WWE_3.02.405.0_radio_sign_25.70.30.05_1.58.26.20
Ruu_Signed_Duttys_WM6.1_5.2.19700_Hybrid_V2_1_64.08.21_CubeV2_ <== the one wich bricked my phone
Ruu_Signed_Duttys_WM6.1_5.2.19700_Hybrid_V2_1_65.14.06_No_CubeV2_
RUU_Kaiser_TMO_UK_3.31.110.3_radio_sign_25.83.40.02_1.70.18.02_Ship
some other topic sugested to use MTTY.
but that probram says: usb port cannot open.
long story short: im desperate.
can any of u please help me fix my phone ?
its an MDA vario II. model Kais130 P/N 99hcy063-00
thanks in advance.
i'm no expert at recovering bricked phones...
but what i understand is that IF you have a hard SPL (which hard SPL do you have?), then you should be able to recover your device from nearly any situation.
try this...if RUU is not working well, try to flash using the SD card method.
also, try to flash a stock ROM (using RUU as well as using the SD card method). let us know what happens.
Try putting your phone into bootloader, ( press and hold power and camera buttons while doing a soft reset ) once it is in the " tri-color " screen, let us know what it says on the screen.
thanks for your time and the fast response, to both of you.
@#1
i used Pofs hard spl.
and as mentioned above i tried both the RUU way and with my micro SD card.
the SD way only shows me the 'Loading' screen. over and over.
and with the RUU i get several errors. connection errors at 0% and connection errors some later.
some roms just say they wont work on my phone.
and others just reboot my phone.
@#2
i think my phone gets to the bootloader all the time. cause i c no difference when resetting with camera and power button on.
its the tri color screen with the folowing information that shows up:
RUUNBH
Kais130
SPL-1.56.0000
CPLD-8
serial/USB
______________________
the serial shows up when the phone is not connected.. and the USB shows up when its attached to my pc with usb.
Any other suggestions ?
Thanks in advance .
You don't have hard-spl you still have a stock, flash the stock ROM of your carrier from bootloader.
Then follow the noobs guide to flashing.
Thx guys my phone is working like it used to be.
downoaded the original rom from t-mobile again. and again.
now got one wich is working.
thanks for your help.
i was about to throw the brick trough the window.
Hello, i was tired of duttys rom so i decided to install the orginal 6.5 windows rom.
It got to 16% and then it got stuck, i tried again a couple of times but it stopped at 16% all the time.
Then i tried to hard reset it, nothing.
Now i tried to install the newest dutty rom.
Now i'm stuck at the "Touch diamond 2" loading screen.
How the hell do i fix it?
Also it loads the RGD thing, but then it just freezes
Please help :s
What does your SPL show?
My spl? Do you mean the RGD thing? if so:
R: 4.49.25.91
G: 61.44etc.25.35U
D 2.53.Dutty
No, put the topaz in bootloader and you can see your actual SPL
SPL-1.33.0linex (stupid 5 mins for edit..)
- Turn off your device using the power button
- When the device is turned off press simultaenously the volume down button + Power button
- Your device will startup in Bootloader mode with band tricolor
Thanks for the help. You sure saved my weekend.
(Got help over pm)
**Deleted**
Nuggi, would you be so kind and share the info with the rest of us, as I have exact same problem as you did in the first post.
Phone dropped to ground, screen got bit smashed so I thought to send it to repair. I put original SPL and 6.1 rom inside and boom, doesn't boot anymore.
EDIT: Found this post, checking now if it works. http://forum.xda-developers.com/showthread.php?p=7191733#post7191733
EDIT2: Success! The software started all fine.