Database Develop

Help Please ! Won't go past the Splash Screen?

I've been trying to get my old extended rom and new Qtek OS on my Wizard (Vario).
But now it gets stuck in the spash screen (ie the one giving the ROM numbers).
I've tried putting the wizard into bootloader mode and I can flash RUU's but when it resets it still gets stuck on the spash screen and won't go any further !!!????
What can I do ??
Please Help
Cheers
John

I should say that I had flashed using button's ROM RUU_Wizard_1050412_WWE_101_11210_WWE.exe.html
and this worked fine!
I then copied across my T-mobile Extended ROM and again everything seemed OK.
BUT then I tried to restore my new saved OS ROM using aWizard and this caused a freeze on my Wizard. It was after a hard reset that the wizard stopped at the splash screen.
Now of course I'm limited in my options because Activesync won't work until the Wizard has fully booted up.
I have tried setting the Wizard into bootloader mode and tried several ROM's (RUU Installer ones) but every time the correct splash screen comes up with the new ROM numbers but that is as far as it gets.
I also noticed on hard reset that you get the following message
Format FAT partition
Format failed
it then goes to the splash screen as before.
Are there any other things I can try Or will I have to send it back to T-mobile for a replacement??
(It's only 2 months old and I have re-flashed it with the orginal T-mobile ROM - but still won't go past the splash screen!!)
I live in hope
John

I have this EXACT same problem!
I can reflash any ROM but it will not go past the splash screen. Only difference was I wasn't playing with my extended ROM. I flashed the AKU2 QTEK ROM yesterday and have been fine through several soft resets, etc. This last time I was uninstalling phonealarm and after a soft reset I got a "could not find smswakeup.exe" (or something similar) and it's been stuck ever since! I also get the "Format Failed" message. Can anyone help!?

I think I'm going to have to send it back to T-mobile and hope they give me a replacement. Something is wrong, it doesn't seem to make any difference what ROM I used.
I think I'll reload the T-mobile shipped ROM grom the FTP site and send it back - and claim ignorance that it it suddenlt freezed and now won't boot up! - Bummer!!!

Right I've logged a fault and it will be sent back - let's hope T-mobile can't detect it's been unlocked and had several ROM updates - I suspect they will try a ROM update themselves then give up ???
The worrying thing though is that it IS possible to kill your phone with updates - maybe it was when I used aWizard to try and restore a ROM that did it??? I'll be more carefull next time!!

this has just happened to one of the devices im flashing at the moment.... absolulty f**king raging :evil: :evil:
i wish teher was a solution!!? anyone got any ideas?
activesync wont find it, so aWizard wont work.
i can flash between 3 roms without any problems (1.5.x 1.6.x 2.x) but always hangs on the splash screen. i have flashed back to the default rom that it came installed with it so i could just send it back to o2 (only 2 days old!)
i would rather just get it sorted by myself thoough so if anyone has ANY ideas then please let me know.
thank you!

Good luck! after about 3 days of trying different types of firmware, I gave up and sent it to expansys, for repair. And it looks like they've lost the bloody thing now. :evil:

tonym001 said:
Good luck! after about 3 days of trying different types of firmware, I gave up and sent it to expansys, for repair. And it looks like they've lost the bloody thing now. :evil:
Click to expand...
Click to collapse
yup looks like i might have to give up... ohwell, no worries i will just return it back to O2...
looks like one of our sales guys wont be getting a new phone on tuesday :lol:

same problem here.
tryed to write os with awizzard after changing extended_rom.
kills phone.
format failed..
Tryed different os's from win util - failed
upgraded with sd card methode worked.
in short :
you need a working wizzard to make a os dump on sd card.
Connect to wizzard with usbterm or romupdate.exe or simular.
do a rs2all command to dump os to sd card.
stick this card in broken phone.
hold voice comm button while resetting.
On ask press voice comm button again.
it bow restores the sd backup to phone.
saved mine.....
btw sd card backup can be read ad write by pc with util ntrw.exe .
so if you don't have a working dump i can upload one.
just mail me.
grtx , arnold

hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.

FarSeide said:
hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.
Click to expand...
Click to collapse
this didn't work for me.
couls flash rom. even splash screen changed to new roms one.
but still stuck at splash...
tried it with about 4 different orgigenal roms
grtx arnold

arnoldl said:
FarSeide said:
hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.
Click to expand...
Click to collapse
this didn't work for me.
couls flash rom. even splash screen changed to new roms one.
but still stuck at splash...
tried it with about 4 different orgigenal roms
grtx arnold
Click to expand...
Click to collapse
Don't worry, I met the same problem as you before, almost lost my hope, but finally I managed to fix it.
The solution is simple, that is to find an original SD card backup image from your wizard or others, then try to restore it in the bootloader mode. In my case, it said checksum error or sth else after begin restoring, and it gave up. Then I put my wizard into bootloader mode, picked one offical released RUU package, start reflash again. Finnally, I found the wirzrd works again for me after reboot.
I guess the principle is that the SD restore will destroy some import flash data structure before it said wrong, then the RUU package will rebuilt it wholely in the next reflash.
Hope this helpful, and sorry for my bad english.

There is hope
Last week after trying to downgrade to the original Cingular ROM on my 8125 using aWizard I ended up with a device that was close to being a paperweight. At least I thought so until I read and read and finally was able to get it to the bootloader and then plugged in the USB cable and ran the RUU for the new Qtek ROM (2.17). Guess what happened, yeah it worked. To my surprise I had a perfect device after 15 minutes.
For about 3 hours I thought I was a toast. Never will I do that again.

THIS is truly heaven for me !!
I have my O2 XDA MINI S locked on the splash screen .. and i updated some ROMS to it ....BUT IT DOESNT GET THROUGH IT .... please tell me what to do in a little detailed manner .. please so that i can get my phone to work.. there is no warranty on the phone and i stay IN INDIA . SO YOU'LL ARE MY ONLY HOPE .
my email id is - [email protected]
If you have a dump of the O2 XDA MINI S ..please mail it to me
Plese tell me what to do next ? WILL TRULY APPRECIATE HELP

PLEASE SOME ONE ATLEAST MAIL ME the dump of the os SO THAT I CAN TRY THE SD CARD UPGRADING ,.,,, O2 XDA MINI S

Re: There is hope
Dear Friend
I have problem that my xda mini s stuck on O2 screen, could you help me step by step.
Thank you so much
my mail : [email protected]
Thanks friend
hellomoto_25 said:
Last week after trying to downgrade to the original Cingular ROM on my 8125 using aWizard I ended up with a device that was close to being a paperweight. At least I thought so until I read and read and finally was able to get it to the bootloader and then plugged in the USB cable and ran the RUU for the new Qtek ROM (2.17). Guess what happened, yeah it worked. To my surprise I had a perfect device after 15 minutes.
For about 3 hours I thought I was a toast. Never will I do that again.
Click to expand...
Click to collapse

Dear Friend
I have problem that my xda mini s stuck on O2 screen, could you help me step by step.
Thank you so much
my mail : [email protected]
Thanks friend
odyseus said:
I've been trying to get my old extended rom and new Qtek OS on my Wizard (Vario).
But now it gets stuck in the spash screen (ie the one giving the ROM numbers).
I've tried putting the wizard into bootloader mode and I can flash RUU's but when it resets it still gets stuck on the spash screen and won't go any further !!!????
What can I do ??
Please Help
Cheers
John
Click to expand...
Click to collapse

stuck on o2 screen helppp
Dear Friend
I have problem that my xda mini s stuck on O2 screen, could you help me step by step.I see alot of post, so complicated
Thank you so much
my mail : [email protected]
Thanks friend
flexchen said:
arnoldl said:
FarSeide said:
hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.
Click to expand...
Click to collapse
this didn't work for me.
couls flash rom. even splash screen changed to new roms one.
but still stuck at splash...
tried it with about 4 different orgigenal roms
grtx arnold
Click to expand...
Click to collapse
Don't worry, I met the same problem as you before, almost lost my hope, but finally I managed to fix it.
The solution is simple, that is to find an original SD card backup image from your wizard or others, then try to restore it in the bootloader mode. In my case, it said checksum error or sth else after begin restoring, and it gave up. Then I put my wizard into bootloader mode, picked one offical released RUU package, start reflash again. Finnally, I found the wirzrd works again for me after reboot.
I guess the principle is that the SD restore will destroy some import flash data structure before it said wrong, then the RUU package will rebuilt it wholely in the next reflash.
Hope this helpful, and sorry for my bad english.
Click to expand...
Click to collapse

how to use bootloader
could you tell me how to use mentioned bootloader for restoring the images? where can I get the software?
Please help
Hendrick
flexchen said:
arnoldl said:
FarSeide said:
hard reset your device and hold your Camera Button prior to starting the wizard back on.
when the device turns back on, you will get the boot screen. Plug in your USB cable and load one of the known ROMS like the second to last iMate ROM.
This will allow you to get past the splash screen.
Click to expand...
Click to collapse
this didn't work for me.
couls flash rom. even splash screen changed to new roms one.
but still stuck at splash...
tried it with about 4 different orgigenal roms
grtx arnold
Click to expand...
Click to collapse
Don't worry, I met the same problem as you before, almost lost my hope, but finally I managed to fix it.
The solution is simple, that is to find an original SD card backup image from your wizard or others, then try to restore it in the bootloader mode. In my case, it said checksum error or sth else after begin restoring, and it gave up. Then I put my wizard into bootloader mode, picked one offical released RUU package, start reflash again. Finnally, I found the wirzrd works again for me after reboot.
I guess the principle is that the SD restore will destroy some import flash data structure before it said wrong, then the RUU package will rebuilt it wholely in the next reflash.
Hope this helpful, and sorry for my bad english.
Click to expand...
Click to collapse

Hi Arnold
My O2 cda mini s get stuck at splash scree, I read your post, still not so understand how to solve it, could you be so kind to write me step by step, and send me some software to solve it. Your help will be so much appreciated.
Hendrick
Email: [email protected]
arnoldl said:
same problem here.
tryed to write os with awizzard after changing extended_rom.
kills phone.
format failed..
Tryed different os's from win util - failed
upgraded with sd card methode worked.
in short :
you need a working wizzard to make a os dump on sd card.
Connect to wizzard with usbterm or romupdate.exe or simular.
do a rs2all command to dump os to sd card.
stick this card in broken phone.
hold voice comm button while resetting.
On ask press voice comm button again.
it bow restores the sd backup to phone.
saved mine.....
btw sd card backup can be read ad write by pc with util ntrw.exe .
so if you don't have a working dump i can upload one.
just mail me.
grtx , arnold
Click to expand...
Click to collapse

HELP!!! phone not working

I REALLY NEED HELP...
i was updating the rom to 2.21 and i guess i accidently closed the program.. sooo now my phone turns on to this screen.. it shows 3 colors.. i can not do anything..
i really need help.. what can i do to go back?

Ok, there's a chance that you just turned your phone into a nice little paperweight however, I recommend trying two things. First, try to perform a hard reset by following these steps:
1: Press and hold both the Comm Mannager Button and the Voice Command Button
2: While keeping those two buttons pressed, press the Reset Button with your stylus
3: After about a second you will be prompted for confirmation. Press the Talk Button to confirm
If that fails, try performing the ROM upgrade again. If THAT fails...well either my assumption is correct or you're gonna need someone more proficient than me to help you ^_^

i tried doing that.. that didnt work..
when you try to install the rom again.. the phone has to be connected with active sync.. and right now its not.. but if u look at the screen on the phone.. it says usb.. but it doesnt connect..
so idk what to do now..
i have another mda..
this one has the original ROM and it works.. is there anything i can do?
please help

harut9161 said:
i tried doing that.. that didnt work..
when you try to install the rom again.. the phone has to be connected with active sync.. and right now its not.. but if u look at the screen on the phone.. it says usb.. but it doesnt connect..
so idk what to do now..
i have another mda..
this one has the original ROM and it works.. is there anything i can do?
please help
Click to expand...
Click to collapse
If you have the bootloader screen(rainbow) it should be retrievable.
Just to be sure you enter the bootloader screen hold camera button and turn on.
The device should be able to connect to your pc, but not by activesync.
If it wont try disabling any firewalls or antiviral on the pc and try again.
Once the pc recognizes your device - run the rom upgrade again.

Fan-freaking-tastic!!!!
Thanks meschle !!!!
I had loaded a cingular rom onto a tmobile thinking all HTC roms should work alike (i know idiot sign is already on my forehead) and the phone was working but very slowly and sync did not work...
I checked and I could get to the bootloader screen (rainbow) as you suggested and then was able to load the original firmware just fine... Phew.. Saved my having to explain a $500 brick to folks.. lol
I have a question on this however, if I want to upgrade the radio or something other than T-MOBILE rom.. what do I need to look for to be sure it will work on my T-MOBILE ?
Cheers
and Thanks

HELP ME! My Tilt Is Bricked.

Ok, so today I tried to flash my Rom with the official att 6.1 rom from HTC. I got it to finally start flashing after about ten tries but when it reached about 13% it gave me an error 276 I think. I tried the recovery method suggested by removing the battery for 3 seconds and reseting the device but now my device isn't recognized in windows and I can't run the upgrade file anymore.
It just goes to the bootloader screen with "KAIS1*0" on the top, then "SPL-3.02.000" below that, and "CPLD-8" below that. At the very bottom it shows USB but my computer doesn't recognize the device. I've tried hard reseting it and it just goes back to the bootloader screen.
Is there any way I can get my Kaiser back or am I screwed?? All this waiting for 6.1 and now my phone is dead. What a load of crap.

Just re start the ruu and let it sit for a minute when that happens, it will start again by itself. Almost shat myself when it happened to me.

First of all, relax. Your phone is not bricked. Do a little looking around the forums and you will resolve this.
I am too lazy to search for him but is the 3.02 SPL compatible with the 6.1 ROM?

I can't restart the Ruu because I can't get a usb connection to my phone. The bootloader goes into usb mode but my computer does not see the phone. The Ruu says it cannot detect the phone either.

Isn't there a way this guy can re-flash using a MicroSD card?

MineralGray02K said:
Isn't there a way this guy can re-flash using a MicroSD card?
Click to expand...
Click to collapse
I'm not sure if the OEM SPL has the ability to flash from card like the Hard SPLs.
To test put the Carrier ROM (Download from the Wiki) on to the root of the MicroSD Card and call it KAISIMG.NBH. Turn on the Phone with the Camera Button Held Down. It should try and flash the ROM then. If that doesn't work, I have a thread and wiki page all about getting stuck on the bootloader, check my Sig for more info.
Hope this helps.
Dave

rodavery said:
Ok, so today I tried to flash my Rom with the official att 6.1 rom from HTC. I got it to finally start flashing after about ten tries but when it reached about 13% it gave me an error 276 I think. I tried the recovery method suggested by removing the battery for 3 seconds and reseting the device but now my device isn't recognized in windows and I can't run the upgrade file anymore.
It just goes to the bootloader screen with "KAIS1*0" on the top, then "SPL-3.02.000" below that, and "CPLD-8" below that. At the very bottom it shows USB but my computer doesn't recognize the device. I've tried hard reseting it and it just goes back to the bootloader screen.
Is there any way I can get my Kaiser back or am I screwed?? All this waiting for 6.1 and now my phone is dead. What a load of crap.
Click to expand...
Click to collapse
run this while phone is hooked up to computer stuck in bootloader.

Sweet Jesus
Ok, I tried the tri-color fix from nufsaid. It didn't work b/c it couldn't open a usb port or didn't see the phone or something. Then I tried putting the rom on my microSD card.
And *SHAZAM* there it was. DaveShaw you are a god to me now. It said the update was successful but I'm still stuck in the bootloader. It used to work if I would plug it into the wasll charger and reset it but that isn't working now. My computer still doesn't recognize it so Mtty or anything still doesn't work.

Ok, I left my tilt on the tri-color screen all night long to run down the battery. When I woke up I tried to power it on and I got the familiar ATT flash screen but when I plugged it into the AC power it went straight into the bootloader.

I don't know what's worse, bootloader or red light of death, I just experienced the red light, called att and got a new phone sent out in 12 hours! What SPL does your phone show? they might exchange if it's not 'voided'

ok, I finally got it to load the windows. If the battery has a high charge or is charging resetting won't get out of the bootloader. If I let the battery run down to almost nothing, wait a little while with it out, then try it again it will turn on. my spl is now 3.56.0000.

Finally
I finally got it out of the bootloader. I'm never going to reset my phone again. It's gonna suck if it freezes. Thanks for all the help.

rodavery said:
I finally got it out of the bootloader. I'm never going to reset my phone again. It's gonna suck if it freezes. Thanks for all the help.
Click to expand...
Click to collapse
Glad your back up and running. There are two new hard SPL's be cmonex (they are mentioned in the link in my sig) that make it less likley for you to get stuck at the bootloader. You could try those?
Ta
Dave

Can't flash Kaiser HardSPL in any way???

Iv'e tryed to flash HardSPL to Kaiser... Downloaded various unlockers/flashers, even SD card solution... When trying to flash over usb with some Kaiser-HardSPL.exe - after entering tricolor mode and when progressbar appears it always stuck on 0%, and nothing happens... Update utility shows error (Rom update utility encountered communication error or smth.) and sugests me to do recovery. Tryed everything - SoftSpl1.56, Softspl1.93, SSpl-kais...
Other method i've tryed - SD card
Iv'e followed instructions, formatted card, copied those two files (http://forum.xda-developers.com/showthread.php?t=420683) to sd card, but after resetting Kaiser it only shows "Loading..." and hangs... no restart, nothing... just "loading..." on screen...
Bootloader menu shows following versions:
KAIS130
SPL-3.29.0000
CPLD-8

somehow... after trying another 1000 -th time... it just flashed...

Have exactly the same problem, tried all other solutions! any idea on what the last method was that worked?

When flashing via USB it will hang at 0% (and fail w/ 260 error on PC side) if the SD card is left in. I've made that mistake more than once.
Remember to remove SIM, too.

I don't have sd card and I've got the same problem...
Any ideas?

I have the same problem. I want to upgrade Hard SPL 3.24 to newer version. I always get 262 error. Also tried all possible ways (MicroSD uses FAT32, but I didn't formatted It, because I don't have SD adapter).
Sometimes It's shown that flashing complete, but HardSPL version still is the same.

Read you noobs
FOLLOW THE DIRECTIONS
http://forum.xda-developers.com/showthread.php?t=396922

latinohot, I'm doing all right...
EDIT:
I changed cable, and it went for the first time

Biker182 said:
latinohot, I'm doing all right...
EDIT:
I changed cable, and it went for the first time
Click to expand...
Click to collapse
good, also check the contact pins, sometimes they get bent.

hmmm...
i STILL can't get hardspl to work at all...just get stuck at 0%

sabzi43 said:
i STILL can't get hardspl to work at all...just get stuck at 0%
Click to expand...
Click to collapse
Are you using sspl to upgrade? sim and sd out? usb cable or sd flash? Do you already have a hspl and are just upgrading?
If you're on an original spl you must use sspl to do it.
If you're upgrading then you can use the kaisdiag file by cmonex and an sd.

aaaaahhhhh
WarByte said:
Are you using sspl to upgrade? sim and sd out? usb cable or sd flash? Do you already have a hspl and are just upgrading?
If you're on an original spl you must use sspl to do it.
If you're upgrading then you can use the kaisdiag file by cmonex and an sd.
Click to expand...
Click to collapse
I'm using usb to windows 7, sim and sd were out.
The thing is i've never done this before, but i am pretty sure i have it down...
I tried this I think 3 times then started to panic when after the recover from the freeze, i noticed things being weird, so i hard reset so i still have a functioning phone until i figure this out.
(it still has bugs it never had before :/)
ive downloaded numorous hardspls, all didnt work.
it's been one saaaaaaaaaaaad experience cuz i really want to make this happen and brag to my guy friends I FLASHED MY PHONE.
and get win 6.5, of course.
any help much appreciated!!!!!!!

sabzi43 said:
I'm using usb to windows 7, sim and sd were out.
The thing is i've never done this before, but i am pretty sure i have it down...
I tried this I think 3 times then started to panic when after the recover from the freeze, i noticed things being weird, so i hard reset so i still have a functioning phone until i figure this out.
(it still has bugs it never had before :/)
ive downloaded numorous hardspls, all didnt work.
it's been one saaaaaaaaaaaad experience cuz i really want to make this happen and brag to my guy friends I FLASHED MY PHONE.
and get win 6.5, of course.
any help much appreciated!!!!!!!
Click to expand...
Click to collapse
copy sspl.exe into your device and run it then you can flash with CustomRUU
to much better you are using ActiveSync on Windows XP

Thanks so much!!! i got it to work!!!! i actually used a jump spl instead, but i now am running win 6.5 on my kaiser!!!!!!! and i'm beyond stoked
THANKS Y'ALL!

Complete and utter noob in help.

Right. I bought this phone (second hand, flashed with shifu 4.2 ROM {I have no clue what this means}) and it worked perfectly. It didn't come with a sim, so I went out and bought two. An O2 and an Orange one. The O2 one had problem's activating, so I placed in the Orange one. The phone somehow screwed up, saying iLockV2.exe is corrupt/could not be found. So, I contacted the seller, he told me to do a hard reset, which I done. The phone worked fine from there.
This afternoon, the phone froze, so I took out the battery and put it back in. The same problem occurred with the iLockV2.exe thing above; so I tried to do another hard reset, it didn't work. After that, I was stuck at the HTC screen where it says:
Code:
R 1.71.09.01
G 25.75.40.02.
D 3.34.shifu
.
I then took out the battery again, and the same thing happened. So I took out the battery once more, and when I pushed the power button it wouldn't turn on. So, I took the battery out and left it for about 4 hours, and put it back in, but now, I'm still stuck at the HTC boot screen (same code as above).
What do I do to make my phone work again?

koglaa said:
Right. I bought this phone (second hand, flashed with shifu 4.2 ROM {I have no clue what this means}) and it worked perfectly. It didn't come with a sim, so I went out and bought two. An O2 and an Orange one. The O2 one had problem's activating, so I placed in the Orange one. The phone somehow screwed up, saying iLockV2.exe is corrupt/could not be found. So, I contacted the seller, he told me to do a hard reset, which I done. The phone worked fine from there.
This afternoon, the phone froze, so I took out the battery and put it back in. The same problem occurred with the iLockV2.exe thing above; so I tried to do another hard reset, it didn't work. After that, I was stuck at the HTC screen where it says:
Code:
R 1.71.09.01
G 25.75.40.02.
D 3.34.shifu
.
I then took out the battery again, and the same thing happened. So I took out the battery once more, and when I pushed the power button it wouldn't turn on. So, I took the battery out and left it for about 4 hours, and put it back in, but now, I'm still stuck at the HTC boot screen (same code as above).
What do I do to make my phone work again?
Click to expand...
Click to collapse
First of all, stop taking out the battery when the phone is on because that really screws up the files. You are doing more harm than good there.
Try a series of soft resets to try and fix it. If that doesn't work, try a series of hard resets to solve the problem.
If no luck there, go into bootloader ( tri color screen ), hold in power and camera button at same time while doing a soft reset. The try flashing a stock Orange rom ( found in the wiki ) Then re-flash with shifu rom.

Not letting me hard reset, so I'm just going to reflash (Y). I hope I do this right :\
EDIT:
My computer can't read my phone when connected via usb D:

koglaa said:
Not letting me hard reset, so I'm just going to reflash (Y). I hope I do this right :\
EDIT:
My computer can't read my phone when connected via usb D:
Click to expand...
Click to collapse
What does the phone do when you try to hard reset ?
When you put your phone into bootloader what does the screen say . When in bootloader, does the bottom of the screen change from serial to usb when you plug it in to your pc ?

denco7 said:
What does the phone do when you try to hard reset ?
When you put your phone into bootloader what does the screen say . When in bootloader, does the bottom of the screen change from serial to usb when you plug it in to your pc ?
Click to expand...
Click to collapse
The phone just soft reset's when I try to hard reset.
And yes, it does change from serial to usb when I plug it into my computer

Seem's like I was doing the hard reset wrong. Same thing is still happeneing, not getting past the part where it says:
Code:
R 1.71.09.01
G 25.75.40.02.
D 3.34.shifu
EDIT:
After 20 or so hard resets, I've moved onto the boot-loader, then it took about 5 minute's to load to the main OS. I think everything is sorted out now. Thanks

omg, this is getting really annoying now. The phone keeps on crashing at random interval's and can only be recovered by hard resetting :\

Well if it keeps happening try a different ROM just make sure you follow F.A.Q for ROM your flashing.
The thing that it's saying is corrupted is S2U2 and to me sounds like it just can't find the .lnk in Windows StartUp.

Flash OEM Rom before the new one and if you have 2GB or smaller SD Card flash using the SD Card method.

stylez said:
Well if it keeps happening try a different ROM just make sure you follow F.A.Q for ROM your flashing.
The thing that it's saying is corrupted is S2U2 and to me sounds like it just can't find the .lnk in Windows StartUp.
Click to expand...
Click to collapse
It happen's when the phone freeze's and I soft reset it :\

koglaa said:
It happen's when the phone freeze's and I soft reset it :\
Click to expand...
Click to collapse
I'd go with what Philux-X says "to which is why i said F.A.Q" try and flash a stock ROM prior to flashing custom so as to clear nand.
The corruption due to stalling sounds pretty normal as the phone does not get to shut down via the usual method.

stylez said:
I'd go with what Philux-X says "to which is why i said F.A.Q" try and flash a stock ROM prior to flashing custom so as to clear nand.
The corruption due to stalling sounds pretty normal as the phone does not get to shut down via the usual method.
Click to expand...
Click to collapse
I'll do that next time it crashes .
Thanks for all your help guys