Hi, I cleaned the screen of my HTC Diamond with a bit of alcohol and a pice of tissue and it seems that the alcohol got inside of the Power button. Now, every time I try to turn the screen on by touching the power button, it turns the screen on but it dispays a message that says: "Warning: Power will be turned off and you may lose data if you have not saved them. Do you want to continue?"
If I click YES, it reboots the phone, If I click NO, then its ok. That is fine, but the problem is when I want to turn the phone off. It's impossible. It will keep trying to reboot.
Does anybody know what can I do? I am really worried.
One solution could be to make some other button from the phone to act as the power button (like the Home button that is rarely used). How can I do that?
Please help!!!!
Thank you
Hi,
I have the same problem.
Did you already find an answer ?
No, I didnt find the solution. I tried to fix the hardware but didnt succeed. So, I created a dummy file to emulate the poweroffwarning.exe that pops up when you long press the power button.
Solution
Hello, I have one AT&T TITL 8925 that upgraded to Windows Mobile 6.5
After the new software was loaded I saw same behavior on my phone.
When the phone is ON and I pressed the power button sometimes it do not respond, and others I received the warning message "power will be turned off and you may lose data if you have not saved them..." My first tought was that it is because the processor is slow to this new software release, or maybe my phone is damaged. I was working perfectly with previous (light version) release so my final guess is that this sw requires more uses of the processos.
Anyways what I have been doing is before turing it off I press the red button or hang up button, and after this if I press the power button it works fine (No more warnings). I have some theories but I will keep doing the same
Hope this partial solution helps you as it does for me.
Regards
Jerry
this is not working for me :| the problem is i can't use my power button not even to open my display when it goes to sleep :|:| i don't know what to do guys please help me
You can use the Stylus to awake the phone, instead of using the power button. You can also use TouchLockPro, to suspend the device, so you do not need the power button for that too.
Also you can set the phone to awake on pressing any key (Windows Mobile Setting), but be sure to have a good locking tool, which makes sure you do not have bogus calls and it goes to sleep again fast enough, otherwise it will drain battery.
I have the same problem.
Anyone solved this one?
I have the same issue and this is not a hardware problem. Strange since even updates/changes of the rom do not correct the issue. Did anybody find a solution for this...?
Well.. ive had this problem just ones.. I was walking downtown with my diamond in the frontpocket of my jeans (face down), after about 3min. of walk, it started to rain (big drops), and my clothes got completely wet, i turned around emidietly, to walk back to home. When i got home after 3 more min. i layed the phone on the table, and then i could hear there were somethibg wrong.. The "turn off" sound came, and the notification kept on coming up, even though i pressed No, as if i were just holding the power button down.. Then i began to press the power button continuesly for about a 100 times, and to my surprise then it stopped and have functioned perfectly for about 2 month now.. Something tells me theres some serius promlem with the smallest kind of moisture near the power button on this phone..
Yes this is hardware related.
If you take a look at the inside of the powerbutton, there are 2 points making contact when you press the button.
If you press it, the software will recognize this and the screen will turn off.
If you press it long enough you'll get the "Do you want to turn off your device" message.
But, if water gets underneath the button, the 2 points may be making contact, because water/alcohol conducts.
In this way you'll get that message.
The button is very weak. Due to this, it may not properly work if you have used it for a long time.
I think that could also be a reason why you constantly get that message.
[ElCondor] said:
Yes this is hardware related.
If you take a look at the inside of the powerbutton, there are 2 points making contact when you press the button.
If you press it, the software will recognize this and the screen will turn off.
If you press it long enough you'll get the "Do you want to turn off your device" message.
But, if water gets underneath the button, the 2 points may be making contact, because water/alcohol conducts.
In this way you'll get that message.
The button is very weak. Due to this, it may not properly work if you have used it for a long time.
I think that could also be a reason why you constantly get that message.
Click to expand...
Click to collapse
Hi! on one of my diamond, the power button off from the board. So the black little board with the button itself is not part of the complete circuit anymore... if someone know the hw testpoint for that it would great please.... i see a few TP around, but if i just start sorting them i just going to kill it...I use to flash phones with TP so is not new for me , but i find nothing for diamond.
I have a similar issue. Mine seems like it is almost stuck on, so it wakes its self up all the time, meaning a full charge lasts an hour or two. Then when it runs out of battery it tries to switch itself back on, so goes through a continuous cycle of vibrating and beeping until the battery is removed. The gf finds it very annoying at 3am lol.
Don't recall mine getting wet, but it's possible it could have got damp at some point, but it's been doing this now for about 3 weeks.
Tried a hard reset with no luck.
[ElCondor] said:
Yes this is hardware related.
If you take a look at the inside of the powerbutton, there are 2 points making contact when you press the button.
If you press it, the software will recognize this and the screen will turn off.
If you press it long enough you'll get the "Do you want to turn off your device" message.
But, if water gets underneath the button, the 2 points may be making contact, because water/alcohol conducts.
In this way you'll get that message.
The button is very weak. Due to this, it may not properly work if you have used it for a long time.
I think that could also be a reason why you constantly get that message.
Click to expand...
Click to collapse
I can see that how to remove the power button from the video showing how to replace the screen. Any idea if once removed the button can be fixed, if not can you get replacements?
2004mark said:
I can see that how to remove the power button from the video showing how to replace the screen. Any idea if once removed the button can be fixed, if not can you get replacements?
Click to expand...
Click to collapse
I think I should send it to HTC, and ask them to do it. Or go to a repair centre. But I should not try it myself, because it can be dangerous for the diamond.
Also try searching on ebay, there might be the parts you could use.
Good luck!
is there a way to remap the power button?
my diamond face same problem since this afternoon, arrrrgghhhh!!!
- blocking hwbutton1, hwbutton2, hwbutton3, hwbutton4, hwbutton5, hwbutton6, hwbutton7 >>>> NO LUCK
- hard reset >>> NO LUCK
guys, any of you solved the problem yet
youtube.com/watch?v=Q4SEQ6AUFOI
My Sony X1 have some strange problems with the power button. When it goes into sleep mode, I can not wake it up with the power button, all I can do is to soft reset. Sometimes it does not go into sleep mode either , it just "wake up" all the time. I don't know what's wrong with it, tried Hard reset but no use .
ANyone had this problems before?
@
The only way to solve this is to leave the phone near your laptop heat vent ( fan) . hot air from it might help you to get the power button up and running. But if that to doesn't work then i'm afraid thats bad.
Current sol :
1. download SU2U ( search threads )
2. go to the settings and make the " lock when stylus inserted" option ON
3. Change the screen turn off time to 5 secs..
So , to unlock , remove stylus , to lock -> insert it back ( its turns off the back light within 5 sec )
Less annoying
elektros said:
youtube.com/watch?v=Q4SEQ6AUFOI
Click to expand...
Click to collapse
thanks for this link, i accidentally tear off my power button flex. now i could turn it on again. Thanks elektros
Hi everyone,
I got a HTC Tytn 2 and i have a problem with it.
When i boot the phone it starts up and goes into windows like every windows mobile phone.
But when i press the standby button my screen wont go out of standby.
Only when i reset the phone it will work again.
Anyone got idea's ?
Oke, since no one responded.
Is there any way how i can make the Power Button replaced with the Speed Dial Button.
Because i think my power button is broke.
WGN88 said:
Oke, since no one responded.
Is there any way how i can make the Power Button replaced with the Speed Dial Button.
Because i think my power button is broke.
Click to expand...
Click to collapse
Have you at least tried backing up your data and doing a hard reset first ?
Yes, and i have also tried to put on a new rom and even updated the radio.
Iam a little bit out of idea's...
here are some more ideas:
1. how to test the power button: you say pressing the power button does not wake up the device once it goes to sleep. conversely, does pressing the power button put the device to sleep while the screen is on? if the power button is unable to make the device go off->on as well as on->off, then the power button is likely broken. if pressing the button achieves on->off, then the power button is probably ok and some software issue becomes more likely.
2. how to enable wake on pressing ANY hardware button: look for an option in Settings. i can't tell you the exact option because the ROM i am using does not have a link for this option, but this option does exist 100% in stock ROM and in lots of other ROMs. it contains settings like "Lock all buttons except power button" and "Keep all buttons unlocked" or something similar. by using the second option, pressing ANY hardware button while the screen is off will wake up the device.
3. you can use AE button plus to perform even more advanced button (re)mappings.
4. just to be sure that your device is really working correct, does the screen wake up when you call the phone or when you receive a text message? if it does not wake up even then, then search for "sleep of death".
Thanks for the response.
I think its a Service of Death problem.
Because when i try calling/smsing it, it wont go on
The buttons do work then...hopefully there's a fix for this problem...
Oke, i tried switching to 2G or 3G only but that didn't fix my Standby of Death.
I also bought a new sim card of vodafone so i wont get a No Sim error.
But what can i do now about it...it hangs like every 5 min...
Okay, after a will testing, the phone hangs every time its almost like when iam on the road with my tytn 2 and placing it upside down, it hangs.
But when iam putting it in the leather holder it doesn't hang.
Any had the same problems ?
WGN88 said:
Okay, after a will testing, the phone hangs every time its almost like when iam on the road with my tytn 2 and placing it upside down, it hangs.
But when iam putting it in the leather holder it doesn't hang.
Any had the same problems ?
Click to expand...
Click to collapse
Maybe it's hardware and something is coming loose
Hey,
I recently received my G1 back from HTC after a repair, However I have realised that it has acquired a new problem since its return. For some reason if you press to hard on the 'Chin' or lower part of the phone where all of the function buttons are such as, Menu and call buttons, the screen will fade to black and will only re-appear on double pressing the end call button, however this doe not always fix the problem. This has become a problem when using the phone as it is very frustrating for the phone to go black and having to double press the end call button inevitably exiting the current application.
I'm reluctant to send it back as I do not want to wait and was wondering if this is a common problem or whether someone suggest something that I could do.
Many thanks
HI every body, I have a problem and I'm asking for help
a while back my HTC HD7 felt in the sea. I managed to get it dried and fixed and it worked fine
but every now and then the screen goes black. normally i fix the problem by taking the battery out
the problem happened again a few days ago, and the screen won't turn on, when I turn the phone on I see the backlights turning on and the touch work fine and I can hear the keys and the unlock screen sound, but can't see anything
I tried to do a hard reset but the volume up key is not working so I can't access the hard reset menu.
my question .. is the a software to do a hard reset via PC. or can I use the headphone volume keys instead of the device ones???
I'm running WP 7.8 official, and a window 7 on PC.
please any help is appreciated ...
thanks