Okey, here is a stange problem!
I purchased a used Tytn II today, and everything seems to work fine! BUT there is a BIG BUT, every time I restart my device it says that the sim card is missing even tough it is in fact in the device, then I have to take the card out reset the device shut it off again and insert the sim card!
Sometime it works and sometimes I have to repeat that procedure several times before it realises that there is a sim card!
Is someone else having this problem, and if yes how do you go around fixing this?
Or is my device simply broke?
Thanks in advance!
I posted this a couple of months ago - works for me
"Happened to me when I got a T-Mobile PAYG SIM last week to trial for data coverage.
Popped SIM in and worked well.
I then tried a Vodafone Sim and that was ok.
When I put the T-Mobile SIM back in - I got the message "no SIM found"
Tried Orange and Vodafone and they both gave the same message !
I was not convinced the SIM'S were making good contact - there seemed too much movement under the flimsy metal crossbar.
The solution to get the T-Mobile and other SIM's working was to insert a small piece of paper on top the SIM as you slide it under the metal crossbar.
This puts a little bit of extra padding on top of the SIM to help make decent contact.
I suppose the paper could be put on top of the crossbar instead to achieve the same effect but have not tried this.
r
Andrew
Also make sure the sim is clean - use a pencil eraser is one suggestion.
So far so good!
bigdish said:
I posted this a couple of months ago - works for me
"Happened to me when I got a T-Mobile PAYG SIM last week to trial for data coverage.
Popped SIM in and worked well.
I then tried a Vodafone Sim and that was ok.
When I put the T-Mobile SIM back in - I got the message "no SIM found"
Tried Orange and Vodafone and they both gave the same message !
I was not convinced the SIM'S were making good contact - there seemed too much movement under the flimsy metal crossbar.
The solution to get the T-Mobile and other SIM's working was to insert a small piece of paper on top the SIM as you slide it under the metal crossbar.
This puts a little bit of extra padding on top of the SIM to help make decent contact.
I suppose the paper could be put on top of the crossbar instead to achieve the same effect but have not tried this.
r
Andrew
Also make sure the sim is clean - use a pencil eraser is one suggestion.
Click to expand...
Click to collapse
Okey, I tried to put some paper between and so far it works!
The strange thing is that I did not even try to replace the card, I just rebooted the device and the sim card was missing!
Cant figure that out!
Hi there,
I just wanted to stop in and say thank you! I have been beating my head against the wall for the past two weeks over why my Tilt kept losing its network connections in perfect conditions and constantly telling me the SIM card was missing. Reseating it only worked once in a great while, but slipping a piece of paper in there seems to have done the trick nicely. I did notice that the contacts on the Tilt dig grooves into the SIM card contacts - do you think perhaps this is the problem or is this common among cell phones?
Thanks Bigdish, worked for me too.
thanks a lot for the information, putting a paper on the SIM resolved the issue in my tytn II, I was so nervous when I saw sim not found in my phone and tried to do reset several times and also repeated the ROM upgrade several times and finally a piece of paper served the purpose thanks....
this is not a repeated topic
i searched all the web for solution but i couldn't find any
my At&t tilt is unlocked it works perfectly for short time ever few resets
else, it give the message "the sim card is missing" you can srtill make emergency calls if your provider supports it
i tried every thing, unlocker, hard spl, all the tools herebut nothing worked
can any body help?
Any chance the SIM is loose in its mounting?
It looks to me like there is a bit is wiggle space in the SIM slot.
did you try another SIM card?
cmegascharf said:
this is not a repeated topic
i searched all the web for solution but i couldn't find any
my At&t tilt is unlocked it works perfectly for short time ever few resets
else, it give the message "the sim card is missing" you can srtill make emergency calls if your provider supports it
i tried every thing, unlocker, hard spl, all the tools herebut nothing worked
can any body help?
Click to expand...
Click to collapse
One of my kaisers uses an old sim where a layer of laminate had been peeling away. This meant that when I inserted the sim, the loose laminate folded back on itself and acted as an insulator between the brass phone and sim contacts. So I removed the offending laminate but still had the occasional "no sim installed". The problem was that the sim was now a little thinner. I applied pressure to the centre of the metal belt that holds the sim in place ensuring that the contacts were "always together" and have not had any problem since.
I hope this simple solution works for you.
Regards,
J
ANother thing you can try is rubbing the gold portion of the SIM card on your jeans or clean it off with a pencil eraser. I had that problem, and it stemmed from a little corrosion or crud building up on the face of the SIM card, and by rubbing it on my jeans it cleaned the corrosion off and the sim was able to make good contact with the points in the card slot.
Sometimes sim cards go bad. I've had about half a dozen go bad out of about 40 devices that I have supported over the last couple of years. AT&T acts like it's a common occurence and no big deal. I just take the device to one of their storefronts and they replace it immediately.
alt236 said:
Any chance the SIM is loose in its mounting?
It looks to me like there is a bit is wiggle space in the SIM slot.
Click to expand...
Click to collapse
i'm not sure, but i tried to add a sticker to the sim card's back but it didn't work
also the mounting seems fine to me
how can i bee sure
g-fall said:
did you try another SIM card?
Click to expand...
Click to collapse
i tried another 5 working sim cards
i have another tilt it's working perfectly with all the other sim cards
[email protected] said:
One of my kaisers uses an old sim where a layer of laminate had been peeling away. This meant that when I inserted the sim, the loose laminate folded back on itself and acted as an insulator between the brass phone and sim contacts. So I removed the offending laminate but still had the occasional "no sim installed". The problem was that the sim was now a little thinner. I applied pressure to the centre of the metal belt that holds the sim in place ensuring that the contacts were "always together" and have not had any problem since.
I hope this simple solution works for you.
Regards,
J
Click to expand...
Click to collapse
thanks alot for ur support
but i tried many other sim cardss
the problem is that is work some time with out any reasons then go "sim card is missing again"
snooginsguy said:
ANother thing you can try is rubbing the gold portion of the SIM card on your jeans or clean it off with a pencil eraser. I had that problem, and it stemmed from a little corrosion or crud building up on the face of the SIM card, and by rubbing it on my jeans it cleaned the corrosion off and the sim was able to make good contact with the points in the card slot.
Click to expand...
Click to collapse
thanks alot
but i tried many other working sim cards "in other att tilts" but it didn't work
mitchrl said:
Sometimes sim cards go bad. I've had about half a dozen go bad out of about 40 devices that I have supported over the last couple of years. AT&T acts like it's a common occurence and no big deal. I just take the device to one of their storefronts and they replace it immediately.
Click to expand...
Click to collapse
i tried lots of other sim cards
thanks every one for ur responses
but i have a feeling this tilt was wae wrongly unlocked
does any one agree with me
is there any way to restore every thing it's initial conditions?
i'm getting frustrated here
Did you try unplugging the battery, put the sim card and then reinsert the battery and start?
[email protected] said:
One of my kaisers uses an old sim where a layer of laminate had been peeling away. This meant that when I inserted the sim, the loose laminate folded back on itself and acted as an insulator between the brass phone and sim contacts. So I removed the offending laminate but still had the occasional "no sim installed". The problem was that the sim was now a little thinner. I applied pressure to the centre of the metal belt that holds the sim in place ensuring that the contacts were "always together" and have not had any problem since.
I hope this simple solution works for you.
Regards,
J
Click to expand...
Click to collapse
hey just wanted to say thanks. i just added a piece of paper between the card and the metal part and it worked. just wanted to say thanks.
I had the very same problem today after putting a brand new sim in the phone.
Found that I had put the damn sim in the wrong way round. Oops.
I had the exact same problem and in my case, putting a piece of paper in did not help at all. I had to get a brand new sim card.
i had a similar problem. it couldn't read my sim card, but read my gf's tmobile sim card and her phone read my sim card fine. then i next day i took it to an ATT shop, asked for a new sim card and it worked perfectly fine now. even the guy from the shop couldn't tell me what is the problem, he said, it happens every now and then.
I bought a new to me tilt. I am using the same sim card as my last tilt, but every few minute/hours I loose all signal and the phone says that there is no sim. I have checked my sim and its clean. I have checked the phone using my wifes sim and i get the same problem. I have stuck a piece of paper behind the sim as it was inserted into the phone and nothing works. After a soft reset it will normally read the sim but doing this every few hours is crazy. I have ordered all required tools and am prepared to do surgery on the phone by switching sim sockets. I would like to avoid this can someone please help.
I need help with my kaiser,
if i turned it on and leave the phone slide is it works good.
But once i close the slide the phone shows sim missing.
I have try to put paper but never worked. Once i close it, it show sim missing.
Pls.. Help ...
http://forum.xda-developers.com/showthread.php?t=500890
Had the same issue. Try remove the SIM card and press down the metal thing. It should bend a little to the inside. Insert your SIM back to the slot and you should have no problem any more. It worked for me
Sim missing...when powered up
I ran into the same issue. it would work with one sim but not another. either add a small piece of paper between the metal clip and your sim. or Do like zmesler said press down on the metal clip. The paper method worked for me, to keep the sim down firmly onto the contacts.
Thanks for the help and the ideas.
I'm having a really weird problem with my XDA Stellar, worked fine for over a year and then suddenly it said No SIM inserted.
Took the SIM out, tried it in another phone - it worked ok.
Used a different SIM in my Stellar - it worked.
Put the original SIM back in - no sim card inserted!
Contacted o2 for a replacement SIM
Inserted and it worked - hurray, for about 24 hours!
Now its back to saying no SIM inserted and as before the SIM works in other phones and other SIMs work in the Stellar.
Anyone any ideas what's going on!
Try cleaning the sim card contacts with a rubber & also try putting a bit of paper/thin cardboard behind the sim so it is pushed onto the contacts in the sim holder better.
Have some threads on this, bit of a known issue.
Do a search if you want more details.
Ahh, many thanks Mister B, the piece of paper did the trick!