i was installing WM5 on my wizard when it gave an error at 85% and stopped. only starts in bootloader but wont install a new one. whats the solution?
thanx
Well... we'll need a little more info in order to help. What is your current ipl/spl? What ROM were you trying to upgrade to? Did you get any kind of error message when the RUU stopped?
was 2.24
and i wanted higher so i downloaded one of the O2 roms
ruu gave a "file not good for ur fon" kinda error
Well.... get into bootloader mode (press the voice button while starting the device until you get the three colored screen) and you can flash the original rom again.
Did you CID-unlock your device first? No? Read read read before flashing again. Start at the sticky.
thing is, how do i flash the fon in bootloader mode?
If you connect it to the pc it will say USB at the bottom of your device screen. You can just flash at this point. No need for activesync. If no USB appears on the screen than you're not in bootloader mode.
ruu says no connection cos it always tries to check the current version first.
Just got my Trinity today, and have successfully unlocked it using pof's unlocker. I unlocked the SIM lock and the CID lock, so it's now SuperCID.
I want to put WM6 on it, the LVSW version. I've downloaded the three files in the sticky post. Before I do it, I want to check that I'm understanding it right, because I'm a bit confused with version numbers.
So...
1) First, I need to HardSPL by running the "ROMUpdateUtility.exe" file from the Hard-SPL.zip file, yeah? I ran this (but didn't flash it) and was confused because the new "Image Version" was 1.20 whereas the Image Version shown in the "current image" bit was 1.24.xxx. Usually, going backwards is bad but I may be misunderstanding.
2) I then need to flash the Radio ROM to 1.41 - why do I need to do this? I guess I run the "ROMUpdateUtility.exe" from the GSM_xxx_xx file, right?
3) Finally, I need to flash WM6 - by running the "ROMUpdateUtility.exe" file from the WM6 zip.
Is that right?
Just tried to flash both the HardSPL and the Radio ROM, and the ROM Update Utility always craps out after I select "Yes" to the security prompt on the Trinity.
"ERROR 246 DEVICE NOT RESPONDING" is displayed in the update utility. Any ideas?
Also, if I go to the bootloader manually (holding down the buttons) the version numbers are:
TRIN100
IPL-0.50
TRIN100
SPL-1.07.0000
But when I let the ROM Update program enter the bootloader, these are shown instead:
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
What does it all mean? Very confusing! It won't let it update anyway, when I select "Yes" to the security prompt, the screen goes black, the ROM updater throws up the error 246 and then the Trinity shows the bootloader.
GazChap said:
Just tried to flash both the HardSPL and the Radio ROM, and the ROM Update Utility always craps out after I select "Yes" to the security prompt on the Trinity.
"ERROR 246 DEVICE NOT RESPONDING" is displayed in the update utility. Any ideas?
Also, if I go to the bootloader manually (holding down the buttons) the version numbers are:
TRIN100
IPL-0.50
TRIN100
SPL-1.07.0000
But when I let the ROM Update program enter the bootloader, these are shown instead:
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
What does it all mean? Very confusing! It won't let it update anyway, when I select "Yes" to the security prompt, the screen goes black, the ROM updater throws up the error 246 and then the Trinity shows the bootloader.
Click to expand...
Click to collapse
SPL by Des is a one time only SPL called SSPL-TRIN.exe, it's somewhere on this board. Sometimes it's baked into a ROM too ... it fakes the SPL.
HARD SPL stays on your phone .... doesn't need SPL by Des anymore.
Windows needs some time to switch from Windows CE to the bootlader driver. This can cause an error ...... just start the exe file again on the PC.
Another common flash error is with Vista, then you need to overwrite the default driver when you're in the bootloader. The driver is in "VistaRUU.zip"
Relaunch the Hard-SPL, then the radio ROM and after that LVSW or mUn's ROM.
There is a file you extract called EnterBootLoader.exe
I copy this to the Memory card.
Then before I run the update I run this on the memory card.
The phone goes to the boot loader and then once windows has re-detected it I run the update.
This seems to have eliminated all problems I've ever had flash updating.
akirainblack said:
There is a file you extract called EnterBootLoader.exe
I copy this to the Memory card.
Then before I run the update I run this on the memory card.
The phone goes to the boot loader and then once windows has re-detected it I run the update.
This seems to have eliminated all problems I've ever had flash updating.
Click to expand...
Click to collapse
I just tried this, but Windows doesn't seem to want to detect the presence of the device when I do. ActiveSync reports that nothing's connected.
Well I've got the Hard-SPL and Radio ROM to flash - instead of leaving ActiveSync connected I just went into the bootloader manually and did it that way.
But now I'm trying to flash WM6 and it gets up to 8% and then craps out with Error 286 - communication errors.
The device now won't boot past the bootloader
What do I do now?
Bloody hell. It's amazing, it really is.
I had it plugged into my USB hub.
Took it out and plugged it directly into the PC, just on the off-chance that the hub was screwed up.
It's all working fine now, I think!
Typical. Thanks for the assistance anyway guys.
Nps. Glad you got it sorted
Is the USB Hub powered? If not that will cause a ton of problems!
It's supposed to be powered, but I'm starting to think that the power supply might be faulty!
hi guys,
2 questions if i can;
1)What is HardSPL?
2) Why are there 3 steps to getting WM6? why can I not use the "ROMUpdateUtility.exe" file from the WM6 zip straight away?
Thanks a lot!!
Same Problem as GazChap
Hey All,
I was having the exact same problem as GazChap with the same configuration to start out with.
This is what I did:
1)plug in my p3600 to the USB
2)let synchronize, and hopefully finish, otherwise stop it
3)run HARD-SPL; this usually freezes after the first go and stalls in the bootloader
4)run HARD-SPL again; this time it will finish. You will have to turn on your machine again after this.
5)run AX3L ROM 2.0.8.2; this ALSO usually freezes after the first go and stalls in the bootloader
6)run the ROM again; This time its gonna work...
Now it works..
brick time
I loaded the hard spl succesfully. I could not get the radio upgrade to load no matter what I did. My instructions said it was optional, so I went directly to the WM6 rom exe load and it has a perpetual communications error after about 8% even though the WM6 loader says each time that recovery is successful. I have a tricolor screen (bootloader?) on my 3600 which won't respond to anything I have thought of yet. Anything I can do other than pitch it? Help! And thanks in advance.
ok, just want to make it short: (P3600 user)
1. I have WM6.1 ROM (FleNover 3.3 Black edition) installed.
2. When I want to downgrade to WM6 official, after 20% it goes error.
3. Now, it only shows 3 colors.
4. Here is my PDA information in 3 colors:
TRIN100
IPL-1.00
TRIN100 MFG
SPL-1.30.Olipro
5. When I want to upgrade with WM6 official, after my PDA shows the progress bar, it restarted and the update screen shows Error 286.
6. How do I fix it?
thank you very much
I have bricked my Hera100 when i flashed OS only
its has the following :
IPL 5.04.0001
SPL 5.04.0000
GSM 03.07.90
OS 1.8.0.0
IT HANGS AT STARTUP SHOWING ABOVE DETAILS ONLY . PLEASE ANY ONE HELP PLEASE. THANKS
wHEN I PUT IT IN BOOTLOADER MODE IT SHOW INVALID ID ERROR WHEN I FLASH , ANY CUSTOM ROM BSE I CANT USE HARDSPL SINCE IT STOPS AT BOOT SCREEN. HELP HELP
try flashing with the sd memory method maybe works
i tried the file named RUU_Herald_DOPODASIA_WWE_1.7.707.3_02.69.90_Ship_ R.exe
although the process finished successfully but my device did not turned on until hard reset then stuck on the boot screen without any response
i get in the bootloader screen saying that
IPL 1.09.0001
SPL 4.10.Ynag
USB
allthough there is the USB indcator at the buttom but when trying to flash the original RUU it did not get the device info as the active sync is not green and the PC cannot identefy a new hardware!?
please could any one help with this situation ASAP
and if i want to restore my ipl to 4.xx
Thanks in advance
Hi
Today I Receive a dead HD7 from a customer.After Repaire Boot with JTAG Phone start and goto Bootloader screen.It Shows SPL-1.23
Now,I cant install any ROM on this set.I try to RSPL and then HSPL but RSPL done ok and HSPL not done.After RSPL and try to install "RUU_Schubert_hTC_Asia_WWE_1.23.707.01_Radio_5.51.09.06a_22.30.50.09_Signed_SCHUBERT_RELEASE.exe" Shows "Flash Write" error and phone dead. I repaire Bootloader for the second time and now phone enter in bootloader with SPL-1.23 .Please tell me that how can i install RUU or custom ROM with no error.
Tnx to all.
what does the Bootloader say?