Database Develop

Very Urgent Help Needed!

Hi,
When I Flashing my ROM (CR86 THD v2.6) it stuck on 88%. What should I do?
Can Someone Help ME Please.
Thanks.

Please HELP HELP HELP!
Now when I tried to flash it again with the cr86 THD v2.5 it said
ERROR 264 : CONNECTION

ERROR [264, 274] : CONNECTION
ERROR [302~318] : UPDATE ERROR
ERROR [320~328] : INVALID COMMAND
These errors seldom occur. However, if one of these errors occur, it could not be recovered and the device had to be sent back to the customer service center. In this case, you have to flash a new ROM code...

I see you have a K-Jam, try this.
Download your original ROM from “HERE” scroll down to K-JAM to find your ROM.
Put the phone in bootloader mode and try flashing the original ROM.

if you can still set your wizard in bootloader mode, try to flash button rom on your device.

Help helpxperia stuck on "continue to upgrade rom please wait"

Sir
i m new here , i hav got xperia stuck on bootloader ,with hardspl so i tried to flash it with some roms availible here
i sucseeded but set got a problem
it get stuck on bootloader but when i try to boot set after connecting usb cable to pc then set got boot normally,then i tried to flash with 072 stock spl after that set stuck in bootloader saying "continue to upgrade rom please wait...."
& if i try to flash any image through sd card then it shows loading..... On pc it shows "usb device not recognised"
please help me

52 visit & not a single reply
sir please guide me 4 this problem

MANISHJOSHI_BKN said:
sir please guide me 4 this problem
Click to expand...
Click to collapse
If you have successfully flashed HardSPL, I suggest you use the SD Card method rather than using PC method. Be patient when flashing ROM's because some ROM's take time to load. Read this thread, it might help you: http://forum.xda-developers.com/showthread.php?t=445662

I had a similar problem.
I just formatted the SD card again, loaded the Kovsimg.nbh file and flashed. It worked for me!

Had the same problem... just flash the stock spl like u did, then try through usb mode but a stock ROM it'll be a successful flashing

Kaiser130.

Hi...
I got stuck in bootloader (Tri-Color)screen with KAIS130 SPL-3.29.HArd i`m not able to boot the OS ... I have installed the
Dutty_s_WM6.1_Official_UC_5.2.19199_RTM__nocube with Radio 1.65.16.25,
i did the HardSPL and still i cannot boot the os cause of the bootloader..
Also i`m trying to 'boot' via mtty.exe but it says command error, it responds
only "task 8" but it stops and cannot write nothing else (device reboots in
bootloder mode)... Is there a way to make my kaiser work ? Cannt unlock
cant change the SPL.
http://forum.xda-developers.com/showthread.php?t=354061
http://forum.xda-developers.com/showthread.php?t=334679
http://forum.xda-developers.com/showthread.php?t=354061
all from these links didn`t help me to boot the phone...
Please just inform me what is wrong in with the spl and how can i reflash again.
Best regards,
In Advance

[Q] Help Required regarding installing new ROM !!!

I am having Xperia X1 Black with factory installed Win Mo 6.1....so, now i wanted to try the Windows Mobile 6.5.3-Build- 29007. Can anyone help me with detailed procedure of installing new ROM on my X1.
I tried according to the procedure available in various post's. According to the procedure i need to first Hard SPL my phone. So, when i try doing that my progrees bar on the phone screen gets stuck at 0% and then i get a error that check the connection of the pc and phone.
In bootloader mode the configuration shown is as follows
KOVS110
SPL-0.78.0000
Micro P1-787
Micro P2-707
I even tried the direct SD card method in which i renamed the ROM file i.e RUU_signed.nbh to kovsimg.nbh...in this when i go to the bootloader mode, the tricolour screen shows with above mentioned specifications then after about few seconds another screen is displayed saying" LOADING..." and then gets stuck.
So, anybody can please help me with installing new ROM
Regards
Bhavik

guitarguru31 said:
I am having Xperia X1 Black with factory installed Win Mo 6.1....so, now i wanted to try the Windows Mobile 6.5.3-Build- 29007. Can anyone help me with detailed procedure of installing new ROM on my X1.
I tried according to the procedure available in various post's. According to the procedure i need to first Hard SPL my phone. So, when i try doing that my progrees bar on the phone screen gets stuck at 0% and then i get a error that check the connection of the pc and phone.
In bootloader mode the configuration shown is as follows
KOVS110
SPL-0.78.0000
Micro P1-787
Micro P2-707
I even tried the direct SD card method in which i renamed the ROM file i.e RUU_signed.nbh to kovsimg.nbh...in this when i go to the bootloader mode, the tricolour screen shows with above mentioned specifications then after about few seconds another screen is displayed saying" LOADING..." and then gets stuck.
So, anybody can please help me with installing new ROM
Regards
Bhavik
Click to expand...
Click to collapse
You bootloader should show
Kovs110
SPL-0.78.OliNex
MicroP1-787
MicroP2-707
don't know if .0000 and OliNex is different
http://forum.xda-developers.com/showthread.php?t=431218
look here for download the good Hard SPL and then replace the 0.78 in it, HARD SPL with cable / computer (I never use SD CARD because it never works for me)
then you TASK29 (find it in the forum), then you can flash it =)

help!!!** HD7 wrong RSPL flashed

heeelllpppp !!!!!! :crying:
first it was this see the image http://d.tuspics.net/IM13/i/00130/bdg2f3zphcub.jpg and i updated it with RSPL version 3 and now when i boot in to the Bootloader see this image http://d.tuspics.net/IM13/i/00130/dxyxkmfsdebb.jpg now the pc cant detect the phone . plsss any help will be appreciated