Htc tilt rgb screen (need help) - Tilt, TyTN II, MDA Vario III General

One day I went to make a call and couldn't.. My htc tilt (AT&T) has a red, green, blue, & white screen with
KAIS1*0
SPL-3.56.0000
CPLD-8
Serial
I did try reflashing the rom several times... 1st few tries show the percent bar but then comes back to the RGB screen... I was able to get it as far as tap to set up the phone... and it gets to the load programs screen... loads everything then will reboot automatically.. but it goes right back to the RGB screen again..
Anyone have any ideas on what I can do (if anything) to resolve this issue? This phone is out of warranty and any suggestions would greatly be appreciated. Thanks in Advance.

http://forum.xda-developers.com/showthread.php?t=423486

Related

dead Kaiser, screen red , green, blue, white

Have my MDA III for 3 month , just wanted to start up my Kaiser as done for hundred times before, got a very short notice: " loading no image found " and after this a red,green,blue and white screen; in the red part it says:
KAIS130
SPL-1.56.0000
CPLD-8
and the device stays on, nothing works.....tried the soft reset, same result
realy dead ??
thoughts ?
Rien
Nope, have you installed hardspl before? If you have simply flash to the rom you had before and start again.
Hi - I had the same problem. I sent it in for repair and they replaced the MainBoard for me. It seems to be a rather serious issue.
I suggest you contact HTC for a warranty repair.

Screen Black with Varying Levels of Light, Responds to Touch... wtf?

So I looked at my screen tonight on my tilt and it was just black.
My Tilt screen has died before and it was a bright white, this is just black. When the machine goes into power standby the black gets a little darker. It responds to touch.
I was able to connect with MyMobiler and access the phone successfully but it's not longer working for some reason. I can still sync and browse my phone from windows.
I did a search and saw that restoring the phone to factory settings may fix this, but I can't seem to do it without a functioning screen.
Regardless, is this screen bricked? Should I try for another warranty replacement? I've already had one... this is stupid.
Any ideas? Thanks
Does anyone know how to at least reset factory defaults with no screen?
http://wiki.xda-developers.com/index.php?pagename=Kaiser_Resets
Hard Reset.

Frozen at SPL-1.40 OliNex Screen

Hello,
Guyz - been using cooked ROM's for ages now and all has been cool till now
:-(
When my Touch Diamond goes to the multi colour screen (not sure on the name for this screen by hey!) its the one with the red, green, blue and white stripy part
anyways... ill continue, on the bottom half of that screen it usually switches from the word 'Serial' to 'USB' then goes onto the next screen where it pushes out the ROM to the device....but the big problem is that it stay on the stripy colour screen saying 'serial' and I have to soft reset the device to go back to the current ROM i have on the machine. I cant push out the SPL 1.24 back to it - it wont take a new ROM onto it :-(
A bit of history - I did have SPL 1.24 on my device and all was cool - have put on SPL 1.40 OliNex recently and I think this is the thing that has caused my problem :-(
Want to know if there is anything I can do?
Cheers,
D^
d3toxuk said:
Hello,
Guyz - been using cooked ROM's for ages now and all has been cool till now
:-(
When my Touch Diamond goes to the multi colour screen (not sure on the name for this screen by hey!) its the one with the red, green, blue and white stripy part
anyways... ill continue, on the bottom half of that screen it usually switches from the word 'Serial' to 'USB' then goes onto the next screen where it pushes out the ROM to the device....but the big problem is that it stay on the stripy colour screen saying 'serial' and I have to soft reset the device to go back to the current ROM i have on the machine. I cant push out the SPL 1.24 back to it - it wont take a new ROM onto it :-(
A bit of history - I did have SPL 1.24 on my device and all was cool - have put on SPL 1.40 OliNex recently and I think this is the thing that has caused my problem :-(
Want to know if there is anything I can do?
Cheers,
D^
Click to expand...
Click to collapse
try disable usb connection in activesync or windows mobile device center if ur using vista

Help KAIS120

Please help me with a HTC KAIS120 I received it today on the color screen, it just gets it, got a firmware 100% but when I ask for the error of the vendor ID is not valid, ask friends to help what can I do?
Thanks
It shows three colour screen?
tell me what text is written on the screen about SPL
like
SPL 3.56.olipof or something like that?
The colors are red, green, blue screen is written KAIS120 SPL 1.94.0000 CPLD-8

Black screen problem

I have a red magic 3 with a black screen problem. It happened to me before and but fixed on its own. The problem before was a backlight problem because I could see (barely of cause). But now, nothing. The phone did not fall on the ground, besides it has a case protection. The problem happened when I manually turned off the screen and it never came back on. I have the LED indicator showing me that the phone is on but nothing else. The vibration happens when I unlock it so it's not a touch screen problem. Any advice would be greatly appreciated.
Does it show boot logon when it starts? Try to boot into recovery mode and do a reset if possible

Categories

Resources