hey guys!
i got a new housing for my phone and i have everything together working great but when ever i receive a text or make a phone call it makes the noise that phones normally make when it is sitting next to a speaker (that really annoying noise) does anyone have any idea why it would be doing this? could shielding be missing?
thank you so much for being my lifeline for my g1
Possiblely a wire not shielded properly or maybe crossed with something elsed. I say take it back apart and check for any loose or frayed wires, maybe also check the routing of the wires and make sure that they are not touching any components that they shouldn't be
okay im going to try that. what wires could cause interference though?
and the noise is coming from the back speaker that plays the phone noises...ringtones, speaker phone, music....etc
It's coming from the loud speaker. Hmmm, I don't know which wires since I have never taken the g1 apart, I was just speaking from taking other things apart and working with car stereos before
Related
I have no sound whats so ever?
I think i know the answer to my problem - i'm just not sure how to fix it.
Basically part of my headset is stuck in the headset port. It's the little tiny tip section of the jack end. I think the phone thinks there is a headset plugged in and thats why the speaker is not working - also when taking calls i cant hear the other person and they cant hear me.
Problem is, what do i do about it? It's an awful small jack fitting in the first place - never mind trying to get the smallest part out of that hole?
Any idea's? I want to avoid returning the phone to O2 because when they last had it (the touch screen stopped working) it took 4 weeks before i got it back and I need the phone for GPS everyday!
OOooooo errrr.
Thats got to be the worst of luck.
I can only siggest two possible things to do and they're nasty, very nasty!
1. Get a cocktail stick and dip the smallest possible amount of SuperGlue on the end(and I mean the smallest dribble.) Infact put a drop on a ceramic tile and dip the cocktail stick into it for a really small amount. Then insert and hold for a few minutes. You may have enough bond to ease out the remains.
2. If you dont use the jack you could shove a nail in there and gently wiggle if for quite a while to break the solder points carefuly and then pull the jack off, thus disconnecting the headset.
Sounds rough and nasty but thats what I'd do and then if it failed I'd put the jack on the remaining headset and send it back to O2 for replacement.
its been a few months now and still no parts for my xperia so i cant get it fixed.
i have been wondering if its possible for someone to make a cab to turn off/on hardware headset jack or forcibly use handset speaker when in a call orsomething?
BTW i have tried all possible fixes using the "search feature"
Are you describing the problem where even though there is nothing plugged into the 3.5mm jack, the XPERIA thinks you've got something plugged in? If so, I'm having the same issue and have found that a quick way to fix this is to take the stylus and wiggle it about at the bottom of 3.5mm jack. This clears it up.
well yeah that worked before but my jack is kinda broken but working
some of the metal in the jack is really loose and the jack has a small broken part.
I had the same issue where my headphone jack reported that there was a constant headphone plugged in, it happened after I plugged a damaged headphone port into the phone.
It took many hours of research and a very intricate and careful dissasembly to fix the issue. I meant to take photos, but my primary camera ( my X1 ) was in pieces at the time..
Anyway, there's a little connector inside the headphone jack that makes contact with a pad, closing a circut, if the connector is bent too far out of the way, it doesn't make contact, and the phone thinks there is a headset inserted.
If your connector is actually broken, you'll have to jerry-rig a wire or something between the two plates to force it to know there's nothing in, but then you lose all headphone functions.
I had to bend the strip of copper to -exactly- how it should be, and it worked out for me, my phone is back how it used to be.
I hope this is of some help to someone, if it happens to me again, I'll document it properly, unfortunately I was in a rush this time, so I didn't have time to prepare properly, I went gung-ho and ripped it to pieces to get it right again.
what about a "software" method of fixing this problem?
doesn't windows mobile support turning headset off, from the registry, for example?
while using radio you can still redirect the sound to the main speaker, (this option is available on the radio panel) something like this feature can help us, i think..
Same problem here. I have tried some suggestion over here but didn't work. You may try it: http://forum.xda-developers.com/showthread.php?p=4485113#post4485113
I'm tired with annoying wire headset and now using a BT headset to be able make/receive calls.
Hope somebody can help us before we send back for repairing.
It happened to me, simply insert a clean "cotton buds" and pull it out again. I think, a dirt just got stuck causing some hardware short circuit or something. Don't know....but it definitely worked for me. I have tried those hardresets, softresets, tweaks and unfortunately none of them worked.
try to drain the battery and charge it back up.
Sometimes would be nice to combine some of the threads because they refer to the same problem
http://forum.xda-developers.com/showthread.php?t=529449
Anyway from my knowledge there are two reasons for this problem.
You may guess
1. Hardware:
This issue had been described very often. Of course the jack is a delicate piece of hardware, which could be damaged physically due to some bad plug or violent force.
2. Software:
It's obvious that the connection is controlled by a piece of software.
I realized that the problem had gone with the latest update.
Maybe it would be helpful to know about the firmware version you got on your phone.
P.S.: Anyone out there who may add this issue to the wiki?
scholbert
Ok im listening to music when all of a sudden the music cuts out, so w/e i unplug and plug in the headphones and it works again. But lately the earphone jack cuts out with any little movement to the earphone at all, i cant listen to music with the phone in my pocket because it cuts out when i take a step.
If anyone has any easy fix for this weird problem, please tell me.
*note: just to be sure it wasnt software based, i went to stock rom and just to make sure it wasnt the earphones i tried it with 5 pairs
any advice?
i've got the same problem, tried using headset blocker, but that didn't help
edit: If someone know how to delete this function out of android, i would be very pleased, because i dont use it!
i fixed it with a little piece of plastic i put between the headphonejack and the case like this:
http://img39.imageshack.us/i/rimg1303u.jpg/
How did you get the plastic in there? i tried biting off a piece of plastic straw but it wont go in all the way
Mine used to do that, but changing to new set of headphones (where the male connector wasn't so worn) fixed the issue for now.
I think the headphone jack is just a little sloppy on tolerances (and a little bit weak too). You might need to send it in for repair.
Markolic said:
How did you get the plastic in there? i tried biting off a piece of plastic straw but it wont go in all the way
Click to expand...
Click to collapse
i used a part of a plastic straw. http://de.academic.ru/pictures/dewiki/116/trinkhalm.jpg
but it was 15 minutes work but it was worth that cause the jack is working like before.
As the title says, I can not hear anything when making or recieving a cal. I can however, when activating the speaker on the side of the phone, hear everything.
I think it could be two things.
1) I just took apart the phone to replace the ribbon cable because it was giving me problems, so I might not have replugged something when reassembling the phone.
or
2) The radio version is either corrupted or not working, and I have not been on the phone scene for over a year, so I do not know the latest version. I am using the very latest version of Energy with sencity (July 4th).
Any suggestions? I can not take calls without everyone hearing it....
Anyone??????????????????????????????????????????????????????????????????????????????????????????????
Also I updated the Hard-SPL to .72 from .52, and then to .78, and then flashed the latest energy ROM. This is really annoying...
thanks...
Had the same issue myself but mine was due to the replacing the casing. I forgot to take out the small speaker in the old casing and put it into the new one. It should be located on the backside of where you place your ear (not a good description, sorry!). If you replaced the ribbon only, I think you should take a look at the prongs of the small speakers to see if they are still good. You could possible bend those prongs so they make more contact with the connection.
Interesting. I guess it might be an internal problem then. Thanks a lot.
I ordered a keypad too, so I will wait for that before I take it apart again. I also need to apply some electrical tape where the internal tape used to be.
All in due time.
I replaced the battery in my wife's phone and immediately afterwards I hear no audio from the earpiece. When I plugin headphones I can hear audio fine from the headphones, youtube pauses when I remove the headphones which indicates it does know that the headphones aren't plugged in and should be sending audio to the earpiece. Does anybody have any idea what connections might be the issue? I have taken the thing apart 4 times trying to find what connector might be misaligned with no luck thus far and really don't want to have to get another phone.
Same exact problem here...
Hi there archangelus2,
Have you ever found a fix to the problem? I also noticed that my loud speaker is now not as loud as it used to be... and by trial and error, I found out that squeezing the top right corner (looking at the screen) it gets a bit louder so I guess that some of the contacts aren't touching well or some other odd crap is going on. The phone is easy enough to open and take apart (if you know what you're doing and are very careful and gentle), but I did notice that given the complains that have been posted post-repair, it does not seem to be too reliable when putting it all back together. The earpiece going completely mute is complete nonsense for instance as there isn't all that much that could go "wrong" in those contacts and I wonder if something gets messed up at the software level after a replacement of hardware like the battery, is performed.
Any help and info will be greatly appreciated.
Cheers! and stay
archangelus2 said:
I replaced the battery in my wife's phone and immediately afterwards I hear no audio from the earpiece. When I plugin headphones I can hear audio fine from the headphones, youtube pauses when I remove the headphones which indicates it does know that the headphones aren't plugged in and should be sending audio to the earpiece. Does anybody have any idea what connections might be the issue? I have taken the thing apart 4 times trying to find what connector might be misaligned with no luck thus far and really don't want to have to get another phone.
Click to expand...
Click to collapse
Is there anyway that you accidentally messed with the earpiece? There is a small rubber protector inside the phone on top of the earpiece, I suggest you check to make sure this is positioned properly on the speaker.
Best of luck,
Matt
Yes, I just got my earpiece fixed. I had a 16 GB AT&T model who's sound was terrific. Then i got greedy and went for a 32 GB latin american model (some telecom I forgot the name of) its earpiece sound was extremely low. I ordered 2 earpieces from ali express just in case they were to be changed. Yesterday I took it to a shop and the guy fixed the original earpiece by applying some tape around the earpiece to focus the sound out of one way and now its as good as new. $10 and am happy.
So yeah probably in your case I'd say he kinda misplaced the earpiece. You may get it checked.