Kaiser no sound problem. Goes Mute Randomly - Tilt, TyTN II, MDA Vario III General

Device Information:
Operator Version: Unlocked
ROM Version: Ultimate-x2.v11 WWE
ROM Date: 02/30/09
Radio Version: 1.71.09.01
Protocol Version: 25.75.40.02.eMoh
ExitROM Version: Premium
Hi, I would appreciate if someone could shed some light on this problem
I get no sound from my Kaiser at Random.
This problem began to happen with my Old RaphaelIII ROM..I do not know which SPL or what radio I had before. (But Im sure it was the one Recommended on the thread.) The phone had run with that ROM for about 6 Months without any sound issues.
I upgraded to ROM Ultimate-v2 because of the sound issue. The symptoms are the same with the new ROM as the old one. I don't think the problem is isolated to the new ROM, that's why I did not post this on the Ultimate-v2 Thread.
I have left the phone playing an mp3 tune on a table, and the sound comes on and off by itself for no apparent reason. the problem includes both speakers. And when I make a phone call I can't hear the other person and they can't hear me neither. The phone does vibrate consistently tho.
Thanks.
Btw Someone here is having the same problem
http://forum.xda-developers.com/showthread.php?t=556339
Edit:
I tested the phone with a bluetooth headset while the sound was gone. I was able to hear and speak fine trough it.
Edit:
I installed another rom and sound is working fine now. but everything else is crappy. this phone sucks.

no sound randomly
Hi there,
I have the same problem.
Mine started after the htc official upgrade from 6.0 to 6.1.
since then intermitted sound during calls (other side can't hear me, i hear them perfectly)
still searching forums on what to do.
spl:3.34dave
radio: varies on ROM (recommended radio)

I have a problem like that. No solution just posting so I can find this post later.
Usually happens to me when I am listing to music and I pull out my head phones.
Speaker sound goes out and when I plug back in the headphones they are also dead.
Ear speaker on calls still works.
Was using WMP to listen to music but switch to S2P a few days ago.
Has not happened since the switch but that may be a coincidence.
Stock 6.1 with ATT stuff stripped.

I have a similar problem to crowbar. Some calls the person on the other end of the line can hear me, some calls they can't. I can hear them perfectly. It' been happening for a few months now. I'm on stock Orange 6.1 (obtained from here). Just bought a cheap Samsung phone to use for now, until I can, hopefully, find a solution. I'm ythinking of trying some of the 6.5 ROMS to see if that cures it.
ROM 3.28.61.0.WWE
Radio 1.65.16.25

Related

Bluetooth Handsfree on MEX-BT2500 - Incoming Calls don't Work

I have an MDA Vario III branded phone using the HTC ROM 1.56.405.5 and a sony MEX-BT2500 (Bluetooth enabled stereo with A2DP).
http://www.audio66.com/product.asp?id=5616&cat=1&man=6&main=1&userid=&firstsel=cat&variation=
The A2DP works well (except it's a pain to enable/disable it using the WM6 interface!) and I can make outgoing calls fine with the phone paired with the Sony but when incoming calls come in, the ringer is routed to the stereo but when I answer it the voice doesn't and I have to hang up and call the person back.
I paired my work Nokia with the stereo and both incoming and outgoing calls work fine.
I tried the original T-Mobile ROM and still had the same trouble.
I'm assuming (with no knowledge of what I am talking about) that the bluetooth stack on WM6 has some issue with routing incoming calls but I can't find any reference to this problem anywhere else and it would seem to be the kind of problem I'd expect millions of users to have a problem with and that there would be a lot of posts.
Does anyone else use bluetooth handsfree? Does it work properly? Does anyone use a bluetooth stereo and A2DP? Does it work properly? Does anyone know if there's a fix?
Thanks for the info in advance...
mine works Ok with my BT2500 although sometimes it needs to be re-paired
Info
Can you tell me what ROM version you have and what model your phone is, radio version, installed programs etc? so I can try changing things.
If you hae a2dp music being streamed and a call comes in does it still work?
ROM is UK Vodafone out-of-the box original (v1615 = Tytn II) 1.56.161.4
Radio is 1.27.12.11
Have Seuth255's A2DPFix from the Hermes forums (prevents skipping)
MS Voice Command V1.6 (i have a SE BT headset too)
Remainder are general apps, gps etc.
haven't tried a call when music is streaming. will do later and let you know
Works for me too, with the original HTC ROM.
Everything is working fine here. I have a MEX-BT2507X, and there's some random 0.2sec cut every 15mins of playtime, but that's not a problem.
Have you used the quickfix from HTC?
jym04 said:
Everything is working fine here. I have a MEX-BT2507X, and there's some random 0.2sec cut every 15mins of playtime, but that's not a problem.
Have you used the quickfix from HTC?
Click to expand...
Click to collapse
I didn't know about the HTC Quickfix. I've just downloaded it and installed but haven't got round to leaving the PC to test it yet. I'll give it a go later and post back.
Fingers crossed...
Audio not working
My audio is not playing through the car speakers with the BT-2500. I had it professionally installed, but was running late to class so I didnĀ“t fully test it until I got home a few hours ago.
I can control the tracks and play/pause, accept/end calls, and the dash microphone works, but my audio is not being pushed and played for some some reason (does work for CD, and Radio). I tried repairing numerous times, resets, and different programs, but no luck... but audio push worked great on a handsfree kit.
any ideas are greatly appreciate... I will take this back to the shop tomorrow, but I would like to know if anybody else experienced this and how they fixed it.
Thanks!! =)
btw, I use stock AT&T rom
eayuwna said:
I didn't know about the HTC Quickfix. I've just downloaded it and installed but haven't got round to leaving the PC to test it yet. I'll give it a go later and post back.
Fingers crossed...
Click to expand...
Click to collapse
...much, much later...
I finally got round to trying it out and even with the quickfix I still have the same problem. My mate also has a Kaiser so I borrowed that (UK O2 ROM I think) and that doesn't work either.
Most odd. maybe I'll ring Sony.
I have the same problem with my Jabra 620s. Maybe somethings wrong with the headset itself?
Can you let me know ur ROM, radio versions so I can see if we have anything the same.

Callers deafened by ringtone when I answer by Bluetooth

Anyone else got this issue and is there a new bluetooth stack or something to resolve it?
When I click the answer button on any bluetooth headset (currently using the iqua solar powered one), the sound is temporarily diverted to by mobile before the bluetooth properly picks up, and also during that slugging moment, any ringtone playing is diverted to the caller's earpiece (i.e. sent out by my mic).
One caller complained it had nearly deafened them.
Anyone able to help?
Having the same issue with my parrot bluetooth and my Tilt
Can someone purrlleeeease help with this issue? I am now scared to answer any calls, lest I get shouted at with, "GOD WHAT WAS THAT NOISE? IT NEARLY DEAFENED ME!"
You really haven't give a lot of info here.
I mean what Rom are you running, what BT hardware and reg tweaks do your use etc.
Info is required to be of any assistance.
Note my signature shows exactly what Rom(s) I'm currently using.
Many thanks. Here are my versions:
HTC TyTN II
ROM: 1.0 Sleuth
ROM date: 08/28/07
Radio version: 1.27.12.11
Protocol version: 22.45.88.07H
Essentially I think a new Bluetooth stack might solve it, but I really wish to avoid losing all data by flashing a new ROM altogether.
A new Bluetooth stack on its own would be wonderful... or a way to restore my data back to a newer ROM. Would Sprite Backup do that if I use Sleuth's WM6.1 ROM?
CJSnet said:
Would Sprite Backup do that if I use Sleuth's WM6.1 ROM?
Click to expand...
Click to collapse
I know the commercial version is supposed to support "Rom Upgrade" support but I'm not sure if that is in the version that is floating around the forums.
What you can do though is make a backup prior to upgrading.
Then upgrade to test if the problem is fixed in one of WM6.1 roms.
Then downgrade and restore your back-up.
Now you will know if there is even a point to expending the effort of trying to extract the BT Stack.
Don't take offense at this next statement but if you put forth that effort it might endear someone more skilled to your cause as you've provided a "Proof of Concept" so to speak.
Okay I have just upgraded to Sleuth's v3 (WM6.1). Sadly the bluetooth issue remains, despite the new Radio version.
If someone calls, and I answer using the bluetooth headset, for 1 second their audio is output to the speaker of the Kaiser. I believe it is during that second that they also hear the end of the ring tone, which is what deafens them.
An unsatisfactory workaround is to use a quite ringtone or vibrate only, but that is hardly ideal. If anyone knows of any other solution or a bluetooth stack that is a bit snappier when answering via headset, it would be great appreciated
CJSnet said:
Okay I have just upgraded to Sleuth's v3 (WM6.1). Sadly the bluetooth issue remains, despite the new Radio version.
If someone calls, and I answer using the bluetooth headset, for 1 second their audio is output to the speaker of the Kaiser. I believe it is during that second that they also hear the end of the ring tone, which is what deafens them.
An unsatisfactory workaround is to use a quite ringtone or vibrate only, but that is hardly ideal. If anyone knows of any other solution or a bluetooth stack that is a bit snappier when answering via headset, it would be great appreciated
Click to expand...
Click to collapse
Same issue here with the same new ROM.
I'm having the same problem. When I push the button on my BT HF it gives a horrible noise to the caller at the other end for a second. In my case I doubt it is ring tone, it doesn't sound anythin like the tone I'm using, it's just like loud crackling or smth.
I can't give you any version numbers cause by TyTN II is sent off to warranty (3rd time already). This time it stopped accepting and making calls while showing 3G symbol. Previously I had band selection on auto and had no problems. Now even after hard reset no calls could be made so off it went again. The first two faults where the speaker and the "Fn" light.
I am having the same problem, the handet is at HTC's repair facility for this and a few nagging issues. I will report what they find.
Mine isn't so much the ringtone it just sounds like a loud static sound. I thought it was the headset but I tried it with 3 different headsets and the Bluethooth in my car and they all have the same problem.
Got my phone back today and I can't say I'm impressed with HTC. First they requested that I send it in the original box then must have thrown it out and sent it in some crap box without enough padding. They didn't even send a note or invoice saying what had been done, which was nothing.
They claim they couldn't find anything wrong and when I called support the guy thought it a joke.
Needless to say it is still deafening and I am pissed.
Same Issue Here... It is almost as if there is a dely in cutting off the WAV/WMA file. Bluetooth Picks up and and both parties get the end of the ring tone.
Had the issued with the origional AT&T rom
Have the issue with Slueth 3.0 and Alex 5.2
If anyone finds a fix please let me know...
I am using PhoneAlarm - Don't know if that is related.
I've had the same complaints from some of my callers, and try to answer between rings as much as possible. The complaints have gone way down. Of course, we shouldn't have to jump thru hoops to answer our phones!
Does anyone have contact info to point HTC to this worrying thread? We need a patch release ASAP. A phone that can't answer calls properly? Yikes.
No issues with my BlueAnt Z9. Have you guys tried different headsets?
I think you may have just been lucky. It is uncommon to A) answer during the ringtone, and B) have the caller complain about the loud noise.
It happens on my Bluetooth earpiece, and Nokia car kit, and JVC car kit. So, it is for HTC to resolve.
I've tried three headsets and it happens on all of them. It happens even when I have the phone on vibrate.
I spent an hour on the phone with HTC support and they are awful, even after telling her that it happens on three different headsets she says that is sounds like a headset issue not an issue with the phone.
When I explained for the third time that I would agree if it happend with one headset but since it happens with all of the headsets it would support my arguement that it is an issue with the phone.
It was like talking to a wall. I wish I had an alternitive to HTC at this point, I love their design and have never had a problem with any of their other phones but this their lack of support is amazing.
I think its with all HTC phones. Happened with my Dash - Wing and now Tilt.
But I've never had anyone complain about hearing music on their end...I can just hear it on my headset for about 1 sec. I've also had my SMS tone play wile on a call and also my VM tone play while on a call and I've asked them if they heard that and they said no.
I also only use noise cancelling headsets.
VooDoo1 said:
I think its with all HTC phones. Happened with my Dash - Wing and now Tilt.
But I've never had anyone complain about hearing music on their end...I can just hear it on my headset for about 1 sec. I've also had my SMS tone play wile on a call and also my VM tone play while on a call and I've asked them if they heard that and they said no.
I also only use noise cancelling headsets.
Click to expand...
Click to collapse
I've never had a problem with any other handset, I've had a Qtek 9100, MDA, O2 Exec, Wing and a Dash.... crap I spent a lot on phones. The only one I've had problems with is the TyTNII.
Same problem here. And sometimes the speaker will very briefly go into speaker mode as I answer! Not good.

Sound problem during the call

Hi!
I've got a Dimond recently and a problem with it. After few days of working fine it stoped to reproduce the sound during the call. If I call to somebody he can hear me, but I can't hear anything (incoming calls also). If I switch on speaker - it works, if I plug in the handset - it works also. I've bought it in Germany, original ROM was - 1.37.407.2. I don't speka German, so I changed it to Elite 2.0 and it worked fine during few days... The main problem is that I'm in Ukraine, so I can't use official service to repair it. Please, help if you know what is wrong...
Did anybody face such trouble?
Few questions:
1. When you put it on loud speaker and it works, what happens when you switch it BACK to internal speaker - does it still work?
2. Have you reset the phone yet?
3. Maybe a hard reset is due?
4. What ROM/Radio versions do you have (start>settings>System>device information)
hi akash_84
i have same problem , and about your questions my answers is:
1. yes it still work>
2. yes many time
3. i do a hard reset but the problem not solve.
4. ROM version: 1.35.401.3 WWE
ROM date: 05/28/08
Radio version : 0.93.25.NS26
protocol version: 52.26.25.09H
Thank you!!!
i have the same problem, on call there is no sound from both speakers (earpiece and loud speaker) all,
done the hard reset and update rom, still no good
thanks
Unfortunately I'm experiencing the same problem with my Diamond. No sound through the earpiece, people can hear me perfectly, no problems when using (bluetooth) headset or speaker. I've been looking around for a while but I can't find any proven solutions. Ultimately, people send their phone in for repair. It seems to be a hardware problem with the headset/no headset switch in the USB connector.
Anybody who had this problem and fixed it themselves?
My Diamond was having the same problem. Nobody in the forum achieved a solution until now. It seems to be a physical problem, not software. I changed the ROM several times without success. I can only replace the equipment. Now let's see what the next problem. This is the second time I return the unit.

Choppy Voice Call on Kaiser (Worse on Speakerphone)

I have a AT&T Tilt running Sleuth 3.0 ROM, with its Radio.
When I'm in call, the person on the other end sometimes doesn't hear me.
It's like the auto cut-off ambience/background noise is working too much, especially when the person background is so noisy, he can hear nothing as if my mic is muted.
This happens very bad if I'm on speaker phone, when I'm driving I put my tilt on the center box, the person on the other hand can hear choppy voices of mine.
Anyone experience this?
It's hard to explain, but basically it's like the old handfree cordless phone on speaker, with auto cut-off ambience feature.
Do I need to upgrade the Radio?
Mine is running 1.64.08.21
Thanks all
I have the same problem. I have 3 At&t tilts phone, 2 of them use Diamond V10, and one is V9. Yet, all have the same problem to you. I hope that if anybody can solve this problem. Thanks so much.
solution
I had that problem to!
In the mobile shop they said we must send it to let it repair.
i thought that can take many weeks!!
What i did was updated my rom to windows mobile 6.1..!
and now i can talk over my speaker and the noise reduction works fine..!!
its much better with WM 6.1..!!!!
I hope it will helps you..!
sorry for my language usage i don't speak english very wel..!
Through searching, I found out a solution that is to upgrade the Radio, for my TIlts Diamond V9 & V10 I use Radio 1.71.09.01. (current is 1.57. .... somthing). It works well now.

Need software patch or tweak for Jawbone problem

I've looked everywhere on this site and maybe I meissed it but I have a jawbone 2 and this is actually my second jawbone through warranty , when I call someone or when someone calls me my jawbone headset brakes up and sounds like im out of range, when I put the jawbone a inche from my tilt then it works perfect .... I need a software patch or something and if this is a subject that has already been resloved please send me the link.
Hope this helps..
I have a newish kaiser and a jawbone2. I flashed several roms, several radios, always ended up finding an issue somewhere, the most recent being the exact persormance issues you've mentioned with the bt/hset.
I'm now using the following, with absolutely zero problems and wonderful quality hands-free, even whilst driving the car @ 70mph with music playing.
Setup:
-rom version: 3.28.61.0. wwe
-rom date: 05/02/08
-radio: 1.65.28.25
-protocol: 25.98.40.07h
It's an updated version of the stock orangeuk rom which came with the device.
Good luck.
Im new to all of this how do I get that on my device?
I'm not comfortable enough with it to explain it myself, so I'll leave it to the experts.
Try here:
http://forum.xda-developers.com/showthread.php?t=433835

Categories

Resources