hey.. ive upgrade to new roms before.. however i tried going from the cingular 2.25 rom to summiters aku 2.3.. and it froze at 98% and was unable to finsh.. now I jsut tried downgrading and it froze again at 98%.. it won't complete anytthing.. help. please.
It's normal for it to seem to freeze at 98%, but it really will complete if you just wait a few minutes. No worries... just be patient.
If Stuck
hey if your phone is doesn't go through with the rom upgrade and doesn't push through and when you reboot you get stuck on the boot screen.
Put your phone into USB programming mode by holding the camera button down and doing a soft reset with the stylus. Then you will be able to load any rom you choose.
With regards to your frozen at 98 just give it time i would say don't unplug
same problem, still stuck
2nd time trying to load "Cingular_Custom_AKU2.3_Combo_Installer_V1.exe" ROM but still stuck at 98%...on the computer it says 100% and finishes but the phone is still stuck at 98%..tried to do a soft reset, but stuck at bootloader screen..
Help pleaseee!
Thanks!
Hi Tried to upgrade the device to latest tmobile 2003 rom. Upgrade went fine. booted it then softreset.
But now it gets to the tmobile and resets. seems stuck in the loop. Now I cant get it to bootloader to try and redo or to use the mitty util. Power and record or power and camera are no longer taking it to booter any ideas?
hello all
yesterday i wanted to flash a friend tp2
when i flashed it it went to 100% and then it gave a rom code error
i restarted the phone in bootloader to flash a other rom and it wanted to read the image on the sdcard
wich resulted in red serie of digits on top of the screen 00058002
and the phone turned off
i deleted the image from the sdcard and tried it again
i came in bootloader and i saw threu the spl text rom upgrade error
now everytime i enter bootloader it turns off the phone in 5 sec
i managed to run a task 29 one time by resetting the phone multiple times
can some one help me
owww its not fixed
i managed to get stock rom on it again but during the custimizsation the phone turned off:S
and now i have the same problem again
edit: i dont know how but its fixed
Hi,
I tried to flash CM11 in my Phone with Odin but it gave a fail as result. So I tried it again with an other firmware but it wasn't possible.
Everytime I connect my Phone to my computer or to the charger is goes into a bootloop. It gives me a screen that says "firmware upgrade encountered an issue" for 2 seconds and it shutsdown, it restarts and give's me the screen with error back.
I think the problem is the CM11 I tried to flash is for an I8190 and I have an I8200 (I found that out to late
I have search google and this forum for 2 days but I didn't find a working solution.
I tried to get into recovery of dowload mode but that's impossible due to the boot loop.
Kies can't connect to my Phone. I checked my powerbutton and it's not stuck.
I removed the battery a couple of times for more than 2 hours, ...
Does someone know what I can do so get my Phone working again?
Hello,
First of all, sorry for my english as it is not my mother language
I've tried today flashing CM13 on my Wiko Rainbow, but I either failed following the instructions or the files I had were corrupted, leading to a never-ending boot.
I don't know if it was already a soft-brick back then, as the phone turned off while booting just after the installation, but 40min after it (obviously because of en empty battery, which was at 37% before installation)
At first, when the phone was plugged into the computer, the phone was booting up, showing the charging icon for a few seconds, and then was going into the infinite boot for 10 seconds, and then rebooting for the same process.
When I was charging the phone on a wall plug, the phone was just in an infinite loop.
The problem was that, when I did the Volume down + Volume up + power thing, I had a choice between Factory mode and Custom mode, but both of them led me to a black screen, and the phone powered off.
I then searched how to install a custom recovery with a soft-bricked phone, and I got a tutorial on SP Flash Tool, that told me to use a MT6582 scatter file, and to select only a Recovery. I downloaded a TWRP for my phone, and then started download, retracted the battery and plugged the phone on the computer.
I got this message : "brom error s_fthnd_file_is_not_loaded_yet"
The software told me to format the Flash, which I did, and this error now became this : "BROM ERROR : S_DL_GET_DRAM_SETTING_FAIL (5054)"
The thing is that now, the soft brick is now a hard brick, and I can't get the phone to boot anymore, adb doesn't recognize my device, and after installing and reinstalling my phone drivers, no solution came out yet, so I'm hopping that you'll find a solution to help my problem
Thanks.
Regards.
MichelFou said:
Hello,
First of all, sorry for my english as it is not my mother language
I've tried today flashing CM13 on my Wiko Rainbow, but I either failed following the instructions or the files I had were corrupted, leading to a never-ending boot.
I don't know if it was already a soft-brick back then, as the phone turned off while booting just after the installation, but 40min after it (obviously because of en empty battery, which was at 37% before installation)
At first, when the phone was plugged into the computer, the phone was booting up, showing the charging icon for a few seconds, and then was going into the infinite boot for 10 seconds, and then rebooting for the same process.
When I was charging the phone on a wall plug, the phone was just in an infinite loop.
The problem was that, when I did the Volume down + Volume up + power thing, I had a choice between Factory mode and Custom mode, but both of them led me to a black screen, and the phone powered off.
I then searched how to install a custom recovery with a soft-bricked phone, and I got a tutorial on SP Flash Tool, that told me to use a MT6582 scatter file, and to select only a Recovery. I downloaded a TWRP for my phone, and then started download, retracted the battery and plugged the phone on the computer.
I got this message : "brom error s_fthnd_file_is_not_loaded_yet"
The software told me to format the Flash, which I did, and this error now became this : "BROM ERROR : S_DL_GET_DRAM_SETTING_FAIL (5054)"
The thing is that now, the soft brick is now a hard brick, and I can't get the phone to boot anymore, adb doesn't recognize my device, and after installing and reinstalling my phone drivers, no solution came out yet, so I'm hopping that you'll find a solution to help my problem
Thanks.
Regards.
Click to expand...
Click to collapse
You're going to need the firmware (not just TWRP) to fix your phone. Have you been able to download it?
Hovatek said:
You're going to need the firmware (not just TWRP) to fix your phone. Have you been able to download it?
Click to expand...
Click to collapse
using SP Tool gives directly through the USB