Help me, hi,
I have a ipaq 6510 that was not use for a while. I put it to recharge a whole night, but what I get is just a blinking startup screen (that one with the hp logo and the 1.10 somethign version ...)- it's coming on for 3-4 seconds, and going off again ... (with USB charger)
I've tried now just with the charger, without the battery, and it's showing me that the device has power, but I can't start it up.
I also tried soft/hard reset, n get a tissue paper under baterray n switch
can anyone help ?
add me on yahoo ID cata_cata_cs and i will help.
Related
Hi, I have been using my HTC diamond toch for nearly 2 1/2 months. a few days ago, i did a rom update using Dutty's rom update. All went fine duing the update. used the phone for about 5 days nonstop, no issues at all.
But yesterday all of a sudden the phone has swtiched off by itself, now it doesn't switch on. Thought the battery might be dead so i tried charging but the enter buttton area doesnt glow and there is no sign of charging.
I switched batteries with a friend to see whether it was faulty but it is in good condition.
What do u think the issue will be ?
Thanks
Buddhi.
I have the same problem. I've just got my phone back from being repaired as the touch screen got all messed up and now it won't charge. I plug it in and the touch pad does the charge animation twice then stops. It'll randomly try to turn on but it doesn't even get to the point where the red writing apears before it turns off again.
Help?!
same problem here
Dudes.... Chill!!!!
Here's what you can all try ....
First you guys need to know that de HTC does not charge if the rom is inconplete/damaged .
And.....
If your batery is realy dead there is no initial power on the internal battery to manage the chargement.
So ... resolution.
Fist way .
If you know any one that may have an other HTC Diamond you need to swamp batteries so the good Diamond that has the internal bat ok and charge it there.
Second way . this one i did it my self .
Go to a Local ChinaMan store and buy a multimeter and a regular Universal Adapter.
Heres how it hoes ...
Use the Multimeter do figure out the polarity pin's on the battery ex: + and - .
remove / cut one of the plug's from the Universal transformer and also tag the polarity.
set the voltage to be close to 5 V - 1 Amp .
Can be 4,5v or 5.5v no sweat
Conect the cuted wire from the Univ. Adapter to the Diamond Battery respecting the polarity.
Leave it for a wile..... ( Probably up to 1 hour but chec from time to time tme battery temperature and if possible a reading on the bat voltage levels.)
Done!
Put the battery bat and boot your diamond or turn on to boot loader.
**** Attention if you don't have more than 50% of the bat charge compleated you wont be able to flash your phone****
Any questions Just reply back.
same problem...
its just...my battery was full before the upgrading...i was Unlocking my Diamond..and the upgrade didnt move more than 0% just when i looked on my mobile...there was black screnn...pluged it out..tried to power on..nothing..tried to charge...nothing again..i tried hard reset(vol down+power+back+reset)..it just wont turn on..please help me..im in panic
Help, I have the same problem and my battery was fully charged before this happened. Voltage reading is 4.2V on the battery.
I also tested the power button and there is nothing wrong with it, it conducts when pushed.
Usually pluging in the charger should start it up, but it will not start.
Anyone have any solutions?
I couldn't fix mine so phones 4 u replaced it with a touch hd
Mattmanico said:
I have the same problem. I've just got my phone back from being repaired as the touch screen got all messed up and now it won't charge. I plug it in and the touch pad does the charge animation twice then stops. It'll randomly try to turn on but it doesn't even get to the point where the red writing apears before it turns off again.
Help?!
Click to expand...
Click to collapse
I had the same exact problem two days ago.The phone was not charging while it was on,and when it was off it did that charging light animation twice and then third time the litght managed to get in the middle of the button and sudennly stopped. So here is my solution . I'v managed to charge the battery on another phone and turned my Diamond back on. While still attached to charger and power source i'v performed a soft reset (by pressing the reset button beneath the stilus) ...the phone reseted and now it's all ok.
bughiman99 said:
I had the same exact problem two days ago.The phone was not charging while it was on,and when it was off it did that charging light animation twice and then third time the litght managed to get in the middle of the button and sudennly stopped. So here is my solution . I'v managed to charge the battery on another phone and turned my Diamond back on. While still attached to charger and power source i'v performed a soft reset (by pressing the reset button beneath the stilus) ...the phone reseted and now it's all ok.
Click to expand...
Click to collapse
I had same problem , no solution yet.
When I had a Mpx220 I had fixed changing a fuse, but I can´t see nothing in internet guides or foruns.
If someone knows how to repair tell us, becouse htc service in our country isn´t good and my device is outdate warranty.
Regards,
Gus
Someone has fixed?
I have the same problem but on my samsung corby GT-i5500. I installed the clockworkmod on my mobile by rom manager and rebooted in recovery, I think i've installed a wrong version and now it does not turn on at all! what should I do? my parents will kill me if they discover that ive broke my phone
hi,
I have a ipaq 6510 that was not use for a while. I put it to recharge a whole night, but what I get is just a blinking startup screen (that one with the hp logo and the 1.40 somethign version ...)- it's coming on for 1-2 seconds, and going off again ...
I've tried now just with the charger, without the battery, and it's showing me that the device has power, but I can't start it up.
I also tried soft/hard reset.
can anyone help ?
- I got it in bootloader mode, and after that somehow it started up
I will come back later with details if everything is working fine
If the battery voltage drops below 3.2V it will not be possible to charg the device.
go to a gsm repair shop and ask them to charge your battery.
Hi all,
I had posted this in the noob section first but got no response
To clear things up, I HAVE searched the forums for this issue & i did find the Topics However it seems whichever solution i try doesn't work.
The Problem: My Sex1i always loads the tricolor screen where it says no image file found.
The only way i get it to load the Win OS is if i either plug in the usb cable or any electric charger cable be it my car charger or wall socket.
Here's what i have tried to resolve it.
1. I have performed a hardSPL following the instructions on this forum.
2. I then update my ROM to the [100% CLEAN WM6.5][2010-01-12] Xperia UnOff Series - Infinite & Xperia X1.5 found on this forum too
3. I have also update my Radio & my camera to the latest roms found on this forum too (Not that they related to the problem anyway)
4. I have tried turning off Active & connecting to MTTY.exe everthing goes as instructed BUT when i connect to MTTY.exe i get a command prompt-like Named [CLIENT] & no matter what i type it just keeps repeating [CLIENT].
So i honestly need assistance with the MTTY.exe program cuz i cant proceed from there.
5. I have tried Soft & Hard Resetting My SeX1i but no joy
My Tricolor screen reads:
KOVS110
SPL-0.72.0LiNex
MicroP1-787
MicroP2-707
Please assist me in case i have missed out on anything.
Thanks in Advance
endzo said:
Hi all,
I had posted this in the noob section first but got no response
To clear things up, I HAVE searched the forums for this issue & i did find the Topics However it seems whichever solution i try doesn't work.
The Problem: My Sex1i always loads the tricolor screen where it says no image file found.
The only way i get it to load the Win OS is if i either plug in the usb cable or any electric charger cable be it my car charger or wall socket.
Here's what i have tried to resolve it.
1. I have performed a hardSPL following the instructions on this forum.
2. I then update my ROM to the [100% CLEAN WM6.5][2010-01-12] Xperia UnOff Series - Infinite & Xperia X1.5 found on this forum too
3. I have also update my Radio & my camera to the latest roms found on this forum too (Not that they related to the problem anyway)
4. I have tried turning off Active & connecting to MTTY.exe everthing goes as instructed BUT when i connect to MTTY.exe i get a command prompt-like Named [CLIENT] & no matter what i type it just keeps repeating [CLIENT].
So i honestly need assistance with the MTTY.exe program cuz i cant proceed from there.
5. I have tried Soft & Hard Resetting My SeX1i but no joy
My Tricolor screen reads:
KOVS110
SPL-0.72.0LiNex
MicroP1-787
MicroP2-707
Please assist me in case i have missed out on anything.
Thanks in Advance
Click to expand...
Click to collapse
Same here, it happened just now, few hours ago
Phone age : exact 365days after purchased.
Suddenly it returns to normal se logo boot up.. I was trying to do a re-Hard SPL it.
1)open the hard spl.exe(just open, don't flash anything)
2)plug in the usb cable connect both phone and computer
3)switch on the phone
then miracle happened!
foxcheng said:
Suddenly it returns to normal se logo boot up.. I was trying to do a re-Hard SPL it.
1)open the hard spl.exe(just open, don't flash anything)
2)plug in the usb cable connect both phone and computer
3)switch on the phone
then miracle happened!
Click to expand...
Click to collapse
I just tried that out, No Joy
Mine also switches on as long as its plugged in to a PC or into the charger, However if i switch my SeX1 on without the cable I still get the tri-color screen
On thing to note though is whenever i plug my phone into a PC, I get the "USB Not Recognized" Balloon first but the storage card device does show up in My Computer
endzo said:
I just tried that out, No Joy
Mine also switches on as long as its plugged in to a PC or into the charger, However if i switch my SeX1 on without the cable I still get the tri-color screen
On thing to note though is whenever i plug my phone into a PC, I get the "USB Not Recognized" Balloon first but the storage card device does show up in My Computer
Click to expand...
Click to collapse
I have an idea, hard reset it while plugging the cable, it will solve the boot up problem
but.. now i can't charge the phone while phone on... i need to switch off the phone before charging...
This looks like same problem I have.
I was recharging my phone as normally, but as I was taking it off the charger after I thought it would be fully recharged, I noticed it hadn't loaded a bit.
I did soft-reset as I thought it would be WinMo glitch and after that it loaded only tri-colour screen. I resetted the phone about 10 times and removed battery and kept resetting. No help.
I had battery out for about 2-3 hours and after that it started normally, but now I had serious problem, it wouldn't recharge battery. I turned off phone and plugged it to charger, I saw that lights started to blink at side and saw that it would recharge normally, and left it for the night.
Morning it had fully recharged. I thought it would be ok at that moment..
Next day I plugged phone to charger again and it did not recharge again.
I started to test chargers for faulty. It wouldn't load from any of my chargers, tested from my computer that was off at time. Tested every USB plug that i could find. Nothing.
My MP3 player charged from every plug and charger, but phone did nothing. I turned on my computer, as Vista was started, I plugged phone and it started to charge! I unplugged it, plugged back, it still loaded.
But now ActiveSync started to bring up errors, saying it could not sync phone and it had problems at desktop(?). Changed phone from ActiveSync to Memorycard, it was acting normally and charging. I thought it was ActiveSync now that was glitching. Never changed it back and got that out of my mind, since I don't sync my phone with my Outlook or vice versa.
I went for a week or two charging my battery from my computer. Testing every once and while from charger, and only noticing it would not charge.
About 2 weeks ago I tested some custom roms from here, as I thought it would help my charging problem. Flashed new WM6.5 custom rom to it, did hard reset. But still it would not charge from charger, only computer.
Flashed back to stock. Next morning I took the phone to shop, where I bought it, for warranty repair, since I have had phone for only for 6 months.
They said it would take 1-3 weeks for repairs and gave me web-tracking code for it. I observed it daily.
Last week I noticed there: "Service delaying, sent for factoryrepair."
I think my phone has fried some chip.
Since then nothing has heard from there, still waiting. Hope they get it fixed fast, since I'm in trouble without my calender!
I wanted to share this all with you because I courage everybody having this problem to take it for repairs. I wouldn't believe they would send it to factoryrepair for having a minor problem.
P.S. sorry about so long text and for any misspelling, english is not my native language.
SE wants us change new phone :S mine is W37 from factory, just 1 year..
did someone solved this problem my sex1 also got this problem..i brought it to cell shop but they just took the usb port from the board itself and now i dont know what to do..the part is still not available..does anyone know the temporary solution i just want to use my phone till the parts arrive..thanks
Hi guys..
I have had my Tilt now for about 2months and recently tried downloading a 200Meg file off the web with it. It drained the power even though the charger was plugged in and so I was clever enough to fool around with chargers...Bleh.. Anyway, so what had happened is that after me switching the phone off etc. I tried charging again without downloading and when I plug the charger in, NOTHING happens..the green light flashes like normal, no light changes and no blips or notifications come up or anything. If I switch the phone off and then plug the charger in, the red light appears and stays there (and I presume it charges). So now I can´t find a fix..Seen MANY other threads regarding similar problems but 90% result in getting a replacement from the supplier which is not possible for me since I don't work off contract and neither is the warranty still valid and neither do I live even NEAR a HTC dealer. I've tried soft resets, hard resets, restarting phone with charger and battery in, without battery in etcetc. The battery is fine.
So it seems my last resort would be opening up the phone and looking if by luck I can see or measure something. Any help at all will be greatly appreciated
Brian
I have same problem, My HTC only charge when power off, No active sync... but i could up rom because in bootloader 3.56 only show USB without serieal . Yesterday i uprom ship end restore SPL. Then my HTC Kaiser can't uprom. It only sirieal when conect USB.
I think it cause by software without hardware. So everyone help us...help me too
Yeah, mine doens't get recognised by my computer at all. Which means no backups or syncs somehow I think my friend's broken TYTN II is gonna come in handy...hmm....
And just for more info, I am as I'm speaking, charging my phone (with it being off) and the red light has been on around an hour long.. Gonna see if it goes off or changes.. Will report back once something happens
Brian
Edit: I just switched my phone on (after around 2 hours charging with it being shut down) even though the light was still red, battery is now 100%.. so.. I'm now downloading the next 200meg file and another 39 files to go
Update: Just something weird.. The tilt was charging(in its shut down mode) and then suddenly switched on by itself.............. uhm..yeah.. so once it came on, i looked and everything was still the same.. pulled out the charger, switched off, put charger back in(cause the battery was about 30%) and boom, green light and switches on again bleh.. so now I fiddled with the battery and charger, and got it to charge in its off state again with the red LED.
http://forum.xda-developers.com/showthread.php?t=372266&highlight=rlod
I thiink, it can "fix in booting safe mode". But I can set it to safe mode
You can try it, follow step in the link, then re tell to me!
every oen, who can help us?!
hey, I took a look there and I tried those things but it didn't work. Apparently there is no "Safe mode" for these phones unless you have a third-party software. So just to confirm, I took a look through the user manual and found nothing, Googled "HTC TyTN II Safe Mode" and found random stuff but not much related besides third-party Apps. So then I just tried randomly fooling around with my TyTN II by holding and pressing random sets of keys while pressing the soft reset button. No luck.
Brian
http://forum.xda-developers.com/showthread.php?t=354061
I find it, i think our KAISER have two problems: can't hardspl and RELoD. Nơ i try follow thí link, maybe SDA application unlock can fix them. But KAiSER can't active sync by USB connect. Now Ifind method activesync by bluetooth. and can find SDA application unlock by SD card. I think MR jockyw2001 have many expriences can help. can you help me?,mr jockyw2001 ?
Hello,
i have ufo rom (I have 1.32 version rom but phone was 1.34 ) and ultimate kernel on my phone for few months now. Yesterday my phone discharged and from that moment I cant turn it on. I plugged it into charger and just orange LED is shining. If I try to turn it on while on charger phone vibrates once and LED stop shining. Display remains black, no other response from mobile at all. I also tried the trick with plastic tape and battery ( because of CWM) but it doesnt work. Also I cannot boot into recovery or anything like that. I also borrowed another desire 500 and took fully charged battery from that phone but it doesnt work either. If I connect phone to computer and then turn it on, again it just vibrates once and nothing else happens and windows recognises it as some type of CD ROM. I really cant help myself, I have read lot of articles but none of them helped. So thanks in advance!
Hold the power button for 20 seconds. Maybe turns on.
...
ufonek said:
Hold the power button for 20 seconds. Maybe turns on.
Click to expand...
Click to collapse
nope, just vibrates once and no other reaction.
up??
So no one has any idea why I cant boot phone??
You have to go back to stock rom. I had the same problem, vibrating 7 times. Added instructions on how to manage to boot and links for the original HTC rom files. In the general thread see my guide