Database Develop

[Walkthrough] How to fix your bricked phone

So, you've decided that your shiny new toy isn't very well setup by default. You flashed a ROM and lo and behold, you missed some instruction somewhere and now you think it's bricked.
Here's the good news:
It's not bricked!!
Bricked means that it's dead and it's in no way or shape recoverable.
There is still a chance. (As long as you didn't try to hardSPL with another Device's SPL...)
All you have to do is:
For the WING:
Hold the Camera button and WHILE holding it, soft reset the device (that means press the little hole above the memory card with the stylus.) That will bring you to the bootloader. Now download the appropiate RUU and run that program. A few minutes later and your new shiny toy is back to it's crappy OEM but working self!
I'll put in links for those who can't find them...
Here's tmobile's ROM.

WOW! That´s all??
Ok - then provide us a link to a XDA Terra RUU!!!!!!
hahahaha. Thanks for this help. Maby for some people it is usefull - but written 1000 times before.
ivanmmj said:
So, you've decided that your shiny new toy isn't very well setup by default. You flashed a ROM and lo and behold, you missed some instruction somewhere and now you think it's bricked.
Here's the good news:
It's not bricked!!
Bricked means that it's dead and it's in no way or shape recoverable.
There is still a chance. (As long as you didn't try to hardSPL with another Device's SPL...)
All you have to do is:
For the WING:
Hold the Camera button and WHILE holding it, soft reset the device (that means press the little hole above the memory card with the stylus.) That will bring you to the bootloader. Now download the appropiate RUU and run that program. A few minutes later and your new shiny toy is back to it's crappy OEM but working self!
I'll put in links for those who can't find them...
Click to expand...
Click to collapse

papamopps said:
WOW! That´s all??
Ok - then provide us a link to a XDA Terra RUU!!!!!!
hahahaha. Thanks for this help. Maby for some people it is usefull - but written 1000 times before.
Click to expand...
Click to collapse
I know it has been stated a million times. I'm just tired of the same question being asked over and over again and so here we are...

Too bad it'll be stated a million more times afterwards too.

falconeyez said:
Too bad it'll be stated a million more times afterwards too.
Click to expand...
Click to collapse
If we sticky it and threatened their lives if they don't read it... lol

ivanmmj said:
For the WING:
Hold the Camera button and WHILE holding it, soft reset the device (that means press the little hole above the memory card with the stylus.) That will bring you to the bootloader. Now download the appropiate RUU and run that program. A few minutes later and your new shiny toy is back to it's crappy OEM but working self!
Click to expand...
Click to collapse
It will not help!

ASerg said:
It will not help!
Click to expand...
Click to collapse
And we hold their pet's hostage?

ivanmmj said:
And we hold their pet's hostage?
Click to expand...
Click to collapse
Or better yet, tell them to send us their phones, then we "unbrick" them and sell them on eBay.

falconeyez said:
Or better yet, tell them to send us their phones, then we "unbrick" them and sell them on eBay.
Click to expand...
Click to collapse
Might work out, I get 10% of the over all sold
Ghostrider

Ghostrider said:
Might work out, I get 10% of the over all sold
Ghostrider
Click to expand...
Click to collapse
Fine, but I get 15% because it's my thread.

The instructions to do this are actually in my newbie thread. Which is a sticky.

TylerC161 said:
The instructions to do this are actually in my newbie thread. Which is a sticky.
Click to expand...
Click to collapse
I know, but most people don't search. I figured, maybe if it says "How to fix your bricked phone" on the title, they might get the idea.
It was actually done mostly as a joke...

help
I used the hardSPL from this thread..
http://forum.xda-developers.com/showthread.php?t=358225
It worked successfully and I was able to restart into WM6. Then I tried loading the TouchIT 4.4 and it installed cleanly with no errors. But when I went to restart it, my Wing just sits there at the CanonYang boot screen and never changes.
I tried using the steps here to restore the tmo default rom, but it after 1% on the progress bar, the screen goes blank and the CanonYang screen comes back. Is there anything I can do?
edit: I can get to the bootloader screen with the color bars. I'm not sure if this additional info will be of any help.
IPL 4.10.0002
SPL 4.70.Yang

gumbico said:
I used the hardSPL from this thread..
http://forum.xda-developers.com/showthread.php?t=358225
It worked successfully and I was able to restart into WM6. Then I tried loading the TouchIT 4.4 and it installed cleanly with no errors. But when I went to restart it, my Wing just sits there at the CanonYang boot screen and never changes.
I tried using the steps here to restore the tmo default rom, but it after 1% on the progress bar, the screen goes blank and the CanonYang screen comes back. Is there anything I can do?
edit: I can get to the bootloader screen with the color bars. I'm not sure if this additional info will be of any help.
IPL 4.10.0002
SPL 4.70.Yang
Click to expand...
Click to collapse
SPL 4.70.yang!!! your device is HARD-SPL!!
So going back to stockrom--> delete the SPL.nbh from EVERY RUU you are running.
Then it shouldn´t stop......

Big Thanks papa! That did the trick. My Wing is happy once again and running Open Touch. But I still want to give TouchIt another try.

And what if i cant find stock RUU mine came with some arabic keyboard and spl was 1.08 , thanks to Oli he didnt mention that SPL should be 4 or higher , so device is bricked since first Olis release and no way to find this arabic stock RUU.
Any Help ?????
Hitec

If the device had an spl of 1.08 prior to HardSPLing it, then you'll have to bring the device to your nearest repair center. There isn't a way around that. Oli doesn't know everything and that's the risk we take when we try new and experimental things that people create but have no way of testing. But, we live and learn. If it wasn't for that issue, you could always cook your own ROM and if the HardSPL was working, you could've easily flashed any ROM. But the keyboard wouldn't been wrong until you could find someone who had the correct keyboard and you extracted the ROM from it and cooked that keyboard driver into your ROM.

Oh noooo!!
Hi ivanmmj,
I used your guide to flashing my HTC P4350 at http://forum.xda-developers.com/showthread.php?t=358615.
It was in French and I wanted it in English. So I downloaded one of the official HTC ROMs "HTC_P4350_WWE_4.17.405.2_4.1.13.44_02.94.90_Ship.exe" assuming this was the English one because all the others couldn't have been.
I copied the "RUU_signed.nbh" from the above HTC ROM and put it into the RUU folder as instructed by yourguide (I didn't copy the SPL.nbh file). I then ran the herald-uspl.exe and everything went fine until the RUU utility stopped with the error "invalid vender ID".
The RUU exited without completing, now all I get when the device boots is the screen giving my IPL (1.08.001) and SPL (1.08.001). How do I flash another ROM from this state? I can't do it the "normal" way because ActiveSync can't see the device. When I try to use the RUU tool that comes with your tool, the progress bar shows then it says the tool can't be used with my device.
Someone please help!

foo_bar_baz said:
Hi ivanmmj,
I used your guide to flashing my HTC P4350 at http://forum.xda-developers.com/showthread.php?t=358615.
It was in French and I wanted it in English. So I downloaded one of the official HTC ROMs "HTC_P4350_WWE_4.17.405.2_4.1.13.44_02.94.90_Ship.exe" assuming this was the English one because all the others couldn't have been.
I copied the "RUU_signed.nbh" from the above HTC ROM and put it into the RUU folder as instructed by yourguide (I didn't copy the SPL.nbh file). I then ran the herald-uspl.exe and everything went fine until the RUU utility stopped with the error "invalid vender ID".
The RUU exited without completing, now all I get when the device boots is the screen giving my IPL (1.08.001) and SPL (1.08.001). How do I flash another ROM from this state? I can't do it the "normal" way because ActiveSync can't see the device. When I try to use the RUU tool that comes with your tool, the progress bar shows then it says the tool can't be used with my device.
Someone please help!
Click to expand...
Click to collapse
Oh wow. I'm so sorry. I think I may have forgotten to put up a warning for people that have an SPL lower than 4.0. Was your SPL lower than 4.0? If it was, you cannot use the USPL OR the HardSPL and they end up writing part of the ROM over your current SPL and brick the device. This, unfortunately, needs to be fixed by your local repair center. I'll talk to the Mods about unlocking that thread so that I can update it.

ivanmmj said:
Oh wow. I'm so sorry. I think I may have forgotten to put up a warning for people that have an SPL lower than 4.0. Was your SPL lower than 4.0? If it was, you cannot use the USPL OR the HardSPL and they end up writing part of the ROM over your current SPL and brick the device. This, unfortunately, needs to be fixed by your local repair center. I'll talk to the Mods about unlocking that thread so that I can update it.
Click to expand...
Click to collapse
Oh deary me! I am so dead now - I live in Tanzania, East-Africa. My "local" repair center is several hundred thousand miles away across The Big Blue. What exactly do the repair center folks do to fix the device? Perhaps I can soldier out myself with some guidance...
Thank you,
foo_bar_baz.

Restore device to OEM without touchscreen

Hello out there.....
First of all i have to say THX to all these people which are really willing to help every1 with their great tutorials. Ive used alot of them already. Thanks.
And i have to say sorry for my english language, due Im german and i left school behind long time ago. I'm really taken pains to write this comment.
Now, in my case ive tried to restore my device (Xperia X1i) to OEM status step by step as its shown in this thread.
My worst issue is that my touchscreen aint work anymore after i flashed a custom ROM and that i got stock at the point where the ROM wants to configure the OS like "Tap the screen to continue with configuration".
Ive tried to flash way too much ROMs using HardSPL but the touchscreen wont let me do anything - no reaction.
So how can I restore the bootloader (SPL) on my device, when my touchscreen aint work? How can I take the following step without any working ROM ?
sirsycho said:
12. Run SSPL.KAIS.exe from your phone (make sure you do this on your actual device and not your PC)
Click to expand...
Click to collapse
I do not know what I did wrong, that the screen wont react anymore, but im sure that the SPL is the cause for this disaster.
I'm really desperate couz i already have sent the device to the SE Support, where they told me that there is an "extraneous" on my device although ive flashed the Stock ROM firstly... there was still something that bothered them...
After i got the device back the touchscreen worked again as funny, allthough the support did nothing on the device as they said in the delivery.
A bit skeptical but with alot of happiness i kept on flashing some ROMs after that.
Now, after i found a good ROM and kept this one on my device for some days the screen doesnt work again.....
This is what my bootloader says right now
Code:
KOVS110
SPL-0.72.OliNex
MicroP1-787
MicroP2-707
....seems like the HardSPL is still there......
Honistly i had to apollogize (maybe too late) that this part of using a cellphone (flashing a ROM using HardSPL etc.) is a big fish and that ive underrated it. Now i have a 400$-Device which aint work anymore
Ive read like all Tutorials here at xda-devs containing something about flashing a ROM or informations about SPLs; tried everything
I feel like im lost and fu**ed right now....
Is there any1 can help me with my problem?
Hopefully there is.....i pray for him

first flash a stock rom
then just run the hard-spl exe, and replace the ruu_signed.nbh file
why are you trying to use kaiser spl?
use the things found in the hardspl sticky in the xperia section

Wrong Tutorial
You're using tutorial for wrong device (HTC Kaiser)
The correct tutorial is in first post (extra how to: how to restore Stock SPL for warranty reasons.)
http://forum.xda-developers.com/showthread.php?t=431218
But before restoring original hardspl you should flash with original rom found in this thread http://forum.xda-developers.com/showthread.php?t=475482

wow thanks for your answers !!
i never thought ill get response.
Its really weird that i havnt found that tut before bcuz i was looking through whole board.
I will try do that tomorrow.
I hope that it will work then. Don't wanna pay 300$ for a new device

Else there is mtty to restore the bootloader

Aight i have done the steps showing in the tutorial.
1. I have flashed teh Stock ROM (R2A german - Vodafone)
2. I've used the RUU with the stockSPL given in that post.
Now my tricolour screen shows the following
Code:
KOVS110
SPL-0.72.0000
MicroP1-787
MicroP2-707
This is what it shall looks like OliNex said.
I hope this is all i had to do, to make use of my device's guarantee, cuz the touchscreen still doesnt work
Seems like i really have to send my Xperia to the Support again (now hopefully with a ROM + SPL they wont reject)
But if i send my device with "extraneous" again i have to pay another 15€ just for let them do a costs estimate -.-
I would like to get a reply before i make use of the support again.
Thanks for all your help

Glad to hear recovering to stock rom + spl worked out.
Your touchscreen doesn't work when you have booted up windows?
If that's correct then I suggest to send in the device for service. Although
it might not help I suggest updating your device with SE updating service (SEUS) first.
After the flash remove the battery for 10 seconds, then turn it on.
Hope it helps and otherwise servicing the device is free of charges

Haha!
That's what im doing right now, using SEUS
Thanks for the tip with the battery but i already tried that way too often
Edit:
Ok, touchscreen still aint work....
Time to contact the support...at 11:45 PM **WOOT
nvm....Ill wait till tomorrow
gn8 and thanks for helping me with my issue ^^

a few days ago I returned my silver X1 for the same issue, my touch screen (digitizer) doesn't work. Then right in front of SE support person, he justed took out the battery and rebooted. Then it worked. The thing is, I did the same thing several times earlier that day and it did NOT worked. I am worrying of getting the same problem again and I only have until november 30th until my 1 year warranty expires. I haven't tried any cooked roms and it is because of warranty purpose. Altough I'm not new to custom roms since I own an Alpine and a Prophet. I've been here for some time now.
The thing that holds me back testing cooked roms on my Xperia is the aftermath if in case my device goes half-dead. I almost always read the restoring on to official roms everytime I get here, but still the thousand dollar spent on my phone's tag price comes with a fear of who's gonna rescue if my phone won't work. And to add that spare parts aren't available here as of the moment. And yes I'm eager and very curious about almost everyone saying cooked 6.5 is faster than stock roms but though I haven't tested it I have to disagree for now on my case basis.
First, my Xperia doesn't come with a carrier lock. It's locally called "open line" in my country I guess technically called debranding. Then my phone has the generic r3a rom via seus I think it's generic uk. Lastly, for some reasons, the touchflo 3d doesn't work with my device I've tried it since r1 firmware time. Some response told me to unlock-debrand my phone first but I dont have to since it isn't locked. Still installing tf3d makes my phone hang, doesn't uninstall, doesn't show in the themes list if installed as a theme, and doesn't let me have another panel since it always stay as tf3d whenever I choose another one. And it is very unstable in my device. These happened even if I install it as a panel.
I feel handsets here are faster than handsets that are locked by a carrier so I'm thinking again since for now, my Xperia works for me as stock as it is.

Help.. I f..... up.. again :)

I am trying to get the cool 4 shortcut buttons and was directed to something called Cookies Home Tab. I installed it but no program showed up.
I would then try and uninstall it an install it again with sense deactivated, but when choosing uninstall on the program (which shows up on the "remove program" menu, but not in the start menu) the "busy-cursor" is just rotating and nothing happens. I tried powering off and try again, and the same thing happens: It says its uninstalling, but it takes forever and nothing happends.
Can someone help? How do I get the program properly installed. I am running a danish original rom and assumed it would be compatible when directed there. I am not sure where to find my sense version. Can it be that its 2.16xxxxx or is that windows?

came99 said:
I am trying to get the cool 4 shortcut buttons and was directed to something called Cookies Home Tab. I installed it but no program showed up.
I would then try and uninstall it an install it again with sense deactivated, but when choosing uninstall on the program (which shows up on the "remove program" menu, but not in the start menu) the "busy-cursor" is just rotating and nothing happens. I tried powering off and try again, and the same thing happens: It says its uninstalling, but it takes forever and nothing happends.
Can someone help? How do I get the program properly installed. I am running a danish original rom and assumed it would be compatible when directed there. I am not sure where to find my sense version. Can it be that its 2.16xxxxx or is that windows?
Click to expand...
Click to collapse
If you cannot find your manila version, or at least search on how to find it, you really need to learn more before you mess up your phone.
I assume you did a hard reset after your registry issue. If not I suggest you do as you will probably have to do it a few times as you attempt to customize your device.
Your manila version can be found in Settings\Device Info\Software Info.
Read the thread on Cookies Home tab for compatable versions and install instructions. Post your questions there.
p.s. Thanks for implying...

I am really sorry for sounding like a total noob, but I DID read the post, installation instructions and whats not. I also read the "how to find your manila version" which also said to go to settings tab - device info - software info. The thing is that its danish on my phone and I cant find anything called device info on my tab, only "about" which leads me to a webpage with a lot of copyright and legal mumble jumble.
When going to settings - advanced - about the device I get a tab called version, where it says Rom Version 2.16.403.1 (67041) dan. But I dont know if thats it.
But lord, how many original stock roms can there be? Its a pretty new phone and I installed every HTC update available to me. I must say that configuring this little diamond seems to take a rocket scientist or above. I can use a computer pretty well, but getting a little modifications to the HTC UI seems to take a phd
You seem like a nice guy, and I would like to learn. Maybe you can help me out so I dont have to ask so many noobish questions. I really tried to learn by myself but it is a new world to me and it is quite overwhelming.
1) I read that installing a rom is ireversible. Does that really mean that I under no circumstances can replace the original software? Is a cooked rom really a whole other OS and replace windows mobile 6.5 completely? Or is it just a modified windows?
2) What is the distinction between HTC Sense, Touch Flo and Manila, if any? As far as I read the black and white icons is manila and the colored ones is sense... Is that true? And does that mean that I cant use any programs that needs manila to run if I have the HTC Ui with the colored icons?
I hope the above questions helps me to a basic understanding, so I further on dont have to ask so many questions.
PS) after installing TD2 tools my screen rotation line in my system registry came back, and I got rid of the landscape.. Thats one problem solved. Call recording aswell. If I find a way to get these 4 shortcut-buttons available and set one of them to my to-do list I think Im done.. No more tampering.. I promise.

came99 said:
1) What exactly is the difference between installing Cookies Home tab and installing another rom? As I understand it, a rom is a whole other OS, where this software only is a skin? Correct?
Correct, The ROM is the whole OS, where CHT is a modification to the Sense (Manila) UI.
2) I read that installing a rom is ireversible. Does that really mean that I under no circumstances can replace the original software?
No, You must first install hard SPL to be able to flash a cooked(custom) ROM.
Once you install HSPL, your device is considered "out of warranty".
However you can reflash a Stock ROM and then reflash Stock SPL to return the phone to the factory state for warranty purposes. So it can be reverted.
3) What is the distinction between HTC Sense and Manila, if any?
They are one and the same, also referred to as Touch Flo 3D (TF3D)
4) The original question about getting Cookie to work, if someone feels like helping.
If you have installed Cookie's Home Tab and soft reset, when you are on your home screen you should see the flip clock (assuming that in Settings\System\Home\Items is set to HTC Sense), on top right of that is a little dash, this opens up additional panels for your shortcuts.
There should also be a new program possibly in settings or \Programs\Tools called CHTEditor to access your tab settings.
I suspect that it installed, you just didn't know how to access it.
Lemme know.
PS) after installing TD2 tools my screen rotation line in my system registry came back, and I got rid of the landscape.. Thats one problem solved. Call recording aswell. If I find a way to get these 4 shortcut-buttons available I think Im done.. No more tampering.. I promise.
Click to expand...
Click to collapse
See above for answers. One quick word of advice; If the program interfaces with your today screen, phone functions, etc. install to device memory and never to Storage Card. Programs that just tweak the registry and settings can be installed to SD card.
Uhm, and I wouldn't be promising anything because its addicting. Once you pop, you can't stop!

Sorry.. I edited my post while you were answering. I found the preguide to roms which was just about basic enough to enlighten me. Your answers helped a lot to, and everything fell into place.
I do think that I will stay away from flashing as it seems like risky business.. The option to hard-reset without to much hassle seems like the emergency brake I like available to me
At the moment I am trying to reinstall Cookies Home Tab, but the installation just hangs.. Probably because it wasnt uninstalled correctly. Any tips other than Hard Resetting which means several hours of setup
Edit: Ahh f... it.. I may aswell do it.. All the tampering made my phone slow anyway.. Now I know what I need and can get it to work without too much experimenting..
Thanks dude.

I did some research on your stock ROM and it looks like you are running Manila 2.1 which is the older version so many tweaks you are attempting may be for 2.5.
You would be better off changing ROMs.
Here is a download of our stock ROM for warranty purposes, keep it just in case. You may have to register for the site, but you may also find a nice cooked ROM in your language on that site. Dutty is a great chef and I use his ROMs because of their stability.
I can attempt to walk you through HSPL, but there have been many issues lately. Almost seems like the only way to get it to work is to "donate" to the developer.

Okay Mr Dope Pusher.. i see where you are going.. Telling me to stay away from these sheningans and 1 hour later you got me hooked anyway
Jokes aside.. Yes.. I Do think I am gonna need some help here.. While the stock backup rom is downloading I will try and find out for myself, but I would very much like some confirmation on what to do before I take the leap.. Stay tuned and thank you very much.. Your help is very appriciated.

I have a question though.. Now I downloaded the stock rom, but what if my phone breaks when Duttys Rom is installed.. Then I wont be able to reinstall the original rom before sending it in for repair. And then Im screwed warranty wise, right?

..., in anticipation of your next question;
As long as you have over 50% battery and do not interupt the flash (unplug the USB) there are very few chances of it bricking.
I have never had it happen and most errors are correctable with a hard reset. It really sounds worse than it is.
Most devices get bricked because the user attempts to flash a cooked ROM w/o HSPL or a ROM or radio from another device.
I have attached 3 files.
Do the following after you download these files;
1. Remove your SIM and SD card.
2. Sync your device to your PC through Active Sync or WMDC depending on your windows version.
2. Copy the enablenewrapi.cab to your device through file explorer and install
to device memory.
3. Open both the SPL 1.83 and the RUU zip files and place contents of both into a new folder.
4. Run the RUU.exe and you should see a progress screen appear.
5. With any luck, you won't get stuck at 0% and the flash will complete.
As the screen states, it may take up to 10 minutes. You will see your device disconnect from active sync, which is normal. Let it run until it completes and do not open anything or let your PC go into standby. Also, you may want to disable your AV and any firewalls as these can mess with the installation.
Make sure you have greater than 50% battery before you attempt this as any interuption during the flashing process can brick your device.
If the steps above complete, you can go into bootloader mode by holding down both volume keys right after you hit the soft reset buton, but before the device begins to boot. You may have to try a couple of times if you are not fast enough. Or you can power off the device then hold both volume keys and press the power button. In bootloader mode which is a tri colored screen, you should see SPL: 1.83.Olinex, then you will know it has installed correctly.
From this point, you are able to flash any cooked Topaz ROM.
The ROM flashing process is the same as HSPL in regards to placing the ROM's .nbh file into the same folder as the custom RUU.exe, so keep that RUU.exe file for future use.
You need only flash HSPL once to continue to flash as many ROMS as you like.
If you ever have to revert to stock, you would install the ROM you downloaded, then find the StockSPL file from the HSPL thread and follow the instructions.
Always hard reset after you flash a new ROM.
**If you are not successful in flashing HSPL, you will need to go to the HSPL thread and read up on opening a ticket with HTC Support, which will give you an autoinstaller that will work once you donate through the program. I believe they are asking for 4gbp.

Ok.. And one of the above files is the Dutty Rom? Edit: Oh I se.. It isnt.. I will download it then..
Will it look and feel similar to Sense, just with more features and customisation options?
You write: Most devices get bricked because the user attempts to flash a cooked ROM w/o HSPL or a ROM or radio from another device.
Can you please elaborate? I understand it like you need to make sure I install the hspl first before cooking, but "radio" from another device. Please explain it for a dummy as me, so I dont attempt to do it by accident.

came99 said:
Ok.. And one of the above files is the Dutty Rom? Is it available in danish as is, or do I have to do something.
Will it look and feel similar to Sense, just with more features and customization options?
Click to expand...
Click to collapse
No, I have not provided you with a ROM, just the HSPL unlocker.
You can go to HTCPedia and search for a Danish ROM with manila 2.5, or take a look through the ROM development thread and find one from another chef. It should have Sense installed but 2.5 unless it states otherwise. 2.5 has more features and functions and is the most current.
Many ROMs are multilanguage so I believe you select your region language when the ROM first loads. Just look for one that supports DAN. I use WWE (World Wide English) so I am not experienced with multilanguage variations.
Just make sure your HSPL is successful before you attempt to flash a ROM.
If you search hard enough you may even find a ROM with CHT cooked in which will alleviate you from having to install it yourself, but I suspect that your previous install didn't work because your on Sense 2.1
I have never used CHT, but use Max Manila Themes which is just a different mod, but I am thinking about trying CHT.
I'll take a look and see what I can find.
Regarding Radios;
A stock ROM comes with the OS and Radio ROM.
Most cooked ROMs take just the OS and tweak it for best performance, adding programs, removing other useless programs and do not include the radio ROM, therefore you will still have your stock Radio unless you flash a cooked ROM that has included the radio (usually denoted in the title of the ROM by the radio#, i.e. 4.49.25.57 (which is a Topaz radio version)
The only time you can brick is you attempt to install a radio from another device (sometimes they work better) such as a Blackstone radio to a Topaz device unless your SIM is unlocked or attempting to flash a Topaz radio w/o HSPL.
Personally, there are enough Topaz radios posted in the radio thread that I don't need my SIM unlocked to try others.
Symptoms of a problem radio are poor signal strength, rapid battery loss and your device heating up.
I have switched my radio ROM a few times but honestly haven't noticed a difference from my stock radio.
The stock ROM you downloaded would replace your Stock Radio if you happen to flash to a different one.
Your region and carrier are also a factor in choosing a radio, so again, just stick to stock unless you have issues.

Dude.. That radio thingie made me EXTREMELY paranoid and I see that there is dozens of different roms from dutty and thousands of rom in general where many of them seems to come with radio-thingies... I am extremely afraid of choosing something that will brick my system, so please, please help me through this, even though you already have been extremely helpful.
If I were on my own, I would go with this:
http://htcpedia.com/duttys_topaz_wm_leo_r_rtm_e11d19c3e22de899a/soft/htc-topaz-rom.html
But to be honest I dont know if it will work on my device or if I will be able to get it with a danish language pack..
Please help me choose the right one.... I am ready to rock, so I hope for a quick reply, and I promise I will do a extra good deed tomorrow to repay the world for all the help you gave me tonight.

came99 said:
Dude.. That radio thingie made me ETREMELY paranoid and I see that there is dozens of different roms from dutty and thousands of rom aswell where many of them seems to come with radio-thingies... I am extremely afraid of choosing something that will brick my system, so please, please help me through this, even though you already have been extremely helpful.
If I were on my own, I would go with this:
http://htcpedia.com/duttys_topaz_wm_leo_r_rtm_e11d19c3e22de899a/soft/htc-topaz-rom.html
But to be honest I dont know if it will work on my device or if I will be able to get it with a danish language pack..
Please help me choose the right one.... I am ready to rock, so I hope for a quick reply.
Click to expand...
Click to collapse
Don't sweat it Bro, if its posted as a Topaz ROM then its got the Topaz Radio, the only thing you risk is not being able to connect to certain 3G bands.
I've used Dutty's R-8 and its not a bad ROM, but its a little outdated and I didn't see that it had multi language support.
I am really having a hard time locating a Danish language ROM.
I find FRE. GER, ITA, ESN, NLD, WWE, but no DAN????

"I am really having a hard time locating a Danish language ROM.
I find FRE. GER, ITA, ESN, NLD, WWE, but no DAN????"
Then it aint just me being total clueless.. I cant find any either..
Im bafled by this world.. I basically have two modest demands: To record calls in mp3 and get easy access to my to-do list.. preferably on my homescreen, but just as good by one of the nifty Hotbuttons Ive seen in pictures..
To get those two modest demands fulfilled I either:
- Need to give up on my danish interface and crack my phone beyond warranty and a chance of bricking it.
- Disable HTC sense and go with WM interface
I know how limited I would be with any other phone, but this road I got myself on is really amazing

came99 said:
"I am really having a hard time locating a Danish language ROM.
I find FRE. GER, ITA, ESN, NLD, WWE, but no DAN????"
Then it aint just me being total clueless.. I cant find any either..
Im bafled by this world.. I basically have two modest demands: To record calls in mp3 and get easy access to my to-do list.. preferably on my homescreen, but just as good by one of the nifty Hotbuttons Ive seen in pictures..
To get those two modest demands fulfilled I either:
- Need to give up on my danish interface and crack my phone beyond warranty and a chance of bricking it.
- Disable HTC sense and go with WM interface
I know how limited I would be with any other phone, but this road I got myself on is really amazing
Click to expand...
Click to collapse
I found some Danish support threads, just search Danish Topaz in XDA and you may find something to load over a WWE rom.
Personnaly I think you will be disappointed if you do not take the plunge.
I had a Rhodium before my Topaz and once I go tmy Topaz, I couldn't stand it. It wouldn't do half the **** my Rhodium did. Because I had my Rhodium flashed to custom.
Finally HSPL was released and I flashed it immediately and can't believe I ever liked that other brick of a phone.
Take your time, get comfy with the process first, and read lots on the language packs.
The brick warning is just a disclaimer and it is very difficult to achieve if you follow the steps correctly.
I know these are expensive toys to take a chance on, but they really are only at 50% capacity out of the box. What a waste....

Bruce, dude, you're a saint. This is why so many folks look to xda for help. You should be commended, but probably won't be! You got my vote.

jdwilson said:
Bruce, dude, you're a saint. This is why so many folks look to xda for help. You should be commended, but probably won't be! You got my vote.
Click to expand...
Click to collapse
Thanks JD!
Is that commended or condemed???
Just trying to give a little back.
Greetz from SoCal.

I agree.. The helpfulnes here has been overwhelming, and has given me the bravery to try this out. But I am still very nervous.
Let me sum up what I learned from tonight.
1) When following your instructions I will have a phone which I can modify with custom roms.
2) As long as I am 100 % sure the rom is for Topaz I dont have to worry about messing up and bricking my phone due to doing wrong stuff to the radio-thingie? (yes, I still dont understand what that is)
3) I will be able to get back to factory defaults and warranty by installing the official rom you linked and afterwards install the original spl thingie afterwards?
4) Should I mess up and brick my phone, there is a fair chance of being able to restore it by the help of another device and a micro SD-card? (See I DO try and learn myself.. (Its probably incorrect though ))
5) I need to give up on the danish interface, but I will without too much hassle be able to get a danish keyboard?
6) To be absolutely sure not choosing a wrong ROM, please confirm this one as a possible choice: "Duttys Topaz HG R10 [5.2.23541.5.5.0]"
It is downloading and I am ready to take the leap... Geronimoooo!

came99 said:
I agree.. The helpfulnes here has been overwhelming, and has given me the bravery to try this out. But I am still very nervous.
Let me sum up what I learned from tonight.
1) When following your instructions I will have a phone which I can modify with custom roms.
Yes
2) As long as I am 100 % sure the rom is for Topaz I dont have to worry about messing up and bricking my phone due to doing wrong stuff to the radio-thingie? (yes, I still dont understand what that is)
Radio controls cell signal, GPS and WiFi connections.
3) I will be able to get back to factory defaults and warranty by installing the official rom you linked and afterwards install the original spl thingie afterwards?
Yes
4) Should I mess up and brick my phone, there is a fair chance of being able to restore it by the help of another device and a micro SD-card? (See I DO try and learn myself.. (Its probably incorrect though ))
Exactly.
5) I need to give up on the danish interface, but I will without too much hassle be able to get a danish keyboard?
Bingo!
6) To be absolutely sure not choosing a wrong ROM, please confirm this one as a possible choice: "Duttys Topaz HG R10 [5.2.23541.5.5.0]"
That's the one I am currently running. Great ROM!
It is downloading and I am ready to take the leap... Geronimoooo!
Click to expand...
Click to collapse
I'm usually not on the forum as much on the weekends but if you get stuck, shoot me a PM which will notify my e-mail and I'll see if I can help.
I take it you were successful with HSPL? If so, thats most of the battle!
Peace!

"5. With any luck, you won't get stuck at 0% and the flash will complete."
Well... Guess what...
Can someone please help.. Im stucked here and having a stroke.
Edit: Tried on 2 different computers and its the same: Stuck on 0 %.. Antivirus disabled.

[Q] How to "virginize" HTC Touch HD?

Hi People
I am not sure whether this is the correct section, but it is still ROM related.
Recently, my phone does not want to wake up sometimes...I press the button and the screen remains black..after few minutes it goes back on but is unresponsive..I have to reset my phone...this is very annoying as for example my alarm also did not sound becuase of this - I was almost late for work...
In conclusion, my 560 EUR phone is not reliable anymore and is still under warranty - I want to have it replaced.
That is where my question comes - How can I completely virginize my phone?
I always used USPL while flashing...
I will perform Task29 and should I flash some stock ROM before I go to give it to service?
If so, what is the appropriate stock ROM for my phone?
What else should I be aware of when virginizing?
Please help me guys, I really want my phone fixed or replaced - it could be the motherboard causing this and I dont want my phone to die...
THANK YOU!!

Sopis said:
Hi People
I am not sure whether this is the correct section, but it is still ROM related.
Recently, my phone does not want to wake up sometimes...I press the button and the screen remains black..after few minutes it goes back on but is unresponsive..I have to reset my phone...this is very annoying as for example my alarm also did not sound becuase of this - I was almost late for work...
In conclusion, my 560 EUR phone is not reliable anymore and is still under warranty - I want to have it replaced.
That is where my question comes - How can I completely virginize my phone?
I always used USPL while flashing...
I will perform Task29 and should I flash some stock ROM before I go to give it to service?
If so, what is the appropriate stock ROM for my phone?
What else should I be aware of when virginizing?
Please help me guys, I really want my phone fixed or replaced - it could be the motherboard causing this and I dont want my phone to die...
THANK YOU!!
Click to expand...
Click to collapse
Dear friend,
first let's know what ROM have you installed on your device? I'm sure the problems that you've mentioned are not hardware problems, and in fact they are related to the ROM, since I have the same problem sometimes with some ROMs and some application. I had problem with alarm clock several times, just after flashing Energy ROMs! I reported this matter, but nobody paid attention, so I downgrade my device to kwbr WM6.1+sense2.1, now I have no problem with alarm clock.
about the another problem, I still have this problem, but I think it is related to WKTask! sometimes when I turn my device off by WKTask shortcut, I encounter the problem that you pointed, but it's not the case if I turn it off by hardware key.

Same question
I have used HSPL
and have tried several roms
Few days back my touchscreen stops responding.
flashed differnet roms but no difference. so i think its a hardware problem
(kinda works sometimes so may be just a loose link)
I want to send it for repair under warranty.. so can someone tell me how to get back to factory settings of Touch HD (German)
Prajwal

Ah, now we have 2 different cases.
1. Flash with USPL
2. Flash with HSPL
I'm almost sure that "virginizing" is described on HD Wiki, but nevermind...
Case 1. is nice and easy...
Go to HTC site and try to find update for your device. Before that, write serial and IMEI (not sure which one is needed, both are under the battery).
If there is "No suitable update", then you are in big trouble... try to find what was original ROM which was on device when it was delivered.
Case 2. is bit difficult... you HAVE TO remove HSPL and restore original SPL, then proceed as described in case 1. I think for german ROM was SPL 1.54
However, I have bought my device recently (with German ROM), but maybe earlier devices had some other SPL...
Check HD Wiki anyway...

prajbio said:
I have used HSPL
Click to expand...
Click to collapse
Ah... [TUT] Dummies guide: flashing 1.56+ roms [v 2.0] - [HSPL][USPL] has at least one important thing for you: stock SPL...

Thanks Guys...
I didnt think of checking the wiki...
Ill go there, and also do what you suggest...
I guess the issue is not related..I flashed a new ROM from different cook and it happened.
Nevermind...I will virginize and then have it fixed or replaced...
THANKS!!

Bodisson said:
Ah, now we have 2 different cases.
1. Flash with USPL
2. Flash with HSPL
I'm almost sure that "virginizing" is described on HD Wiki, but nevermind...
Case 1. is nice and easy...
Go to HTC site and try to find update for your device. Before that, write serial and IMEI (not sure which one is needed, both are under the battery).
If there is "No suitable update", then you are in big trouble... try to find what was original ROM which was on device when it was delivered.
Case 2. is bit difficult... you HAVE TO remove HSPL and restore original SPL, then proceed as described in case 1. I think for german ROM was SPL 1.54
However, I have bought my device recently (with German ROM), but maybe earlier devices had some other SPL...
Check HD Wiki anyway...
Click to expand...
Click to collapse
From my experience, HTC is usually ok as long as the SPL is an official one. No matter the one came with your phone or other older/newer version.

Sopis said:
Hi People
I am not sure whether this is the correct section, but it is still ROM related.
Recently, my phone does not want to wake up sometimes...I press the button and the screen remains black..after few minutes it goes back on but is unresponsive..I have to reset my phone...this is very annoying as for example my alarm also did not sound becuase of this - I was almost late for work...
In conclusion, my 560 EUR phone is not reliable anymore and is still under warranty - I want to have it replaced.
That is where my question comes - How can I completely virginize my phone?
I always used USPL while flashing...
I will perform Task29 and should I flash some stock ROM before I go to give it to service?
If so, what is the appropriate stock ROM for my phone?
What else should I be aware of when virginizing?
Please help me guys, I really want my phone fixed or replaced - it could be the motherboard causing this and I dont want my phone to die...
THANK YOU!!
Click to expand...
Click to collapse
since you just use USPL, you just need download the official ROM from HTC page by inserting your HD serial number under ROM download. then flashed it. it think this step will solve your warranty issue.

Problem with HTC Kaiser Tytn II - please help...

So my problem is - I put android on my htc tytn II and it worked (well kinda) but anyway I decided to switch back to Windows Mobile...
I installed 1.27.x.x radio , found a Windows Mobile 6 ROM and put (Like in the instructions ) Kaisimg.nbh(renamed from ruu_signed.nbh) and Kaisdiag.nbh to my SD card and then started flashing... It flashed smth,rebooted automatically and started booting android again...
Then I hold again camera button + power+ reset and since then when I put EVERY .nbh file on my sd card and try to flash it it STUCK on "Loading.." If I try to flash it with USB It stays at 0%.
The only exeption is if I try to flash from USB the rom that I tried to flash before from my sd card.. then it starts 0%..1% and reboot the phone...
P.S: Please help me...I think my device is not Broken but I dont know what should I do to fix it...

To flash back to WM from android put your kaiser into bootloader (multi colored screen) Then connect to usb. Download any WM build that is recent (I suggest Phoenix 3 for this, you can flash whatever you want later). After you download it open and run the included RUU that came with it and it will flash it on there.

hmm, I also had experienced the similar problem on my 1st time flashing back to WinMo.
When you are trying to flash via USB cable and the process stopped at 1% I guess there is also a message about "Invalid vender ID" right?
and if the text in your bootloader (tricolor screen) doesn't mention anything about hard such as "3.29.0000" (not "3.29.hard")
then
you've lost your hard SPL that's why you cant flash any .nbh to your phone.
I had managed to solve this problem by flashing stock WM rom for kaiser. The rom also has to be suitable for your phone, I mean if your kaiser is originally from France, then use French kaiser stock rom. Or if you are using AT&T Tilt use kaiser cingular stock rom.
you can find the list of shipped roms for kaiser here :
http://shipped-roms.com/shipped/Kaiser/
If you still have the "invalid vender ID" error message, try another stock ROM.

Thanks man you're my hero! I though I lost my phone.. anyway i bought new one - Nokia 2730 Classic but Ill sell the kaiser...
Thanks Anyway ... you're god!

Have the same problem...
Firstly, I'd like to point that the reason for the hard SPL getting overwritten by an original SPL is NOT HAVING UPDATED HARDSPL to a newer version that prevents accidental overwrite. This is instructed in the previous steps before actually installing Android. That was my mistake (I had HardSPL 1.0 OliPof), and now I can't flash no rom to my Kaiser (which thankfully works quite well in Android).
What happens (please correct me if I'm wrong) is that "KAISDIAG.NBH" is a modified, standalone hardSPL that will flash to the phone the SPL that comes with the "KAISIMG.NBH" you put in your SD card with "KAISDIAG.NBH"). In my case, I used the WinMo 6.1 spanish version 3.29.412.0, which, resulted in my phone being flashed with the original SPL 3.29.
Now, it seems many users have fixed this locating the correct stock rom and flashing it in their Kaisers. But to others, like myself, nothing seems to work. I believe that this is because we not only need a stock rom for our specific Kaiser model, but also it has to be compatible with the SPL that accidentally got installed in the phone. The problem is what if such rom doesn't even exists?
I'm really thankfull for all I learned by reading the forums (and from my mistakes ) and I know I'm in no position to make requests, but here goes what I think could help the users like myself to fix this, if posible:
1) Guide to identify what model of Kaiser we have (maybe it's already there, I just couldn't find it)
2) Complete list (or lists) of stock roms (There are some around, those are easy to find I think, but it doesn't hurt to share different sources)
3) Something like a JumpSPL for Android would be more than awesome...
Thanks in advance to everybody, sorry for my own stupidity . Any idea or help would be much appreciated,
Daniel

hmm, I'm not sure if it has to be compatible with the SPL.
In my case, I was flashing a very old WWE stock rom which has original SPL 1.56.
I also had been very desperate because any stock rom I found seems doesn't work and I even didn't know where originally my kaiser came from because I get it from my uncle. So I tried to flash any WWE stock rom I could found but nothing works. I read from Wikipedia that based on my phone model (Kais100), this model was only sold as AT&T tilt for US. But the problem is my phone is HTC branded, not AT&T tilt. Well, based on this information I also tried to flash some cingular stock rom but the result was just the same.
After contacting HTC Customer care, I know more info about my phone. They told me that based on my phone product ID, my kaiser was originally shipped for US, but unfortunately they can't provide me stock rom for my phone model. So I searched myself but this time I had better objective : to search HTC branded rom but for US.
finally, after days of search. I've found the rom that is suitable for my phone. Its called HTC WWE Brightpoint US which has original SPL 3.29 at the bottom of the list on the website I told you on my previous post.
few weeks ago I also accidentally overwrite my HardSPL again, but this time I did it with the stock ROM which has original SPL 3.29. But this problem also solved by flashing the stock ROM I've found before via USB cable.
So, I guess it has nothing to do with spl version.
Keep tying don't give up.

Update: Step 1 completed! YAY
Using the serial number and some obscure google searching, I came to the conclusion my KAIS130 is australian. Cheers, mate!
I verified this by being able to download stock roms from the australian HTC site with my Kaiser serial number. But at the moment of writing this, have downloaded two roms and no luck yet. 5 minutes remaining for the third one... Wish me luck...
Daniel.

Well... Now what?
Tried all four rom-like thingies I could download on the HTC page, all of them returning error 294...
Now what? try to somehow extract the .nbhs from the exes and and use customRUU.exe? Try to flash from SD card?
Please help... Any ideas... I really want to get rid from that original SPL3.29.0000 It's evil!!! I think it won't never let me flash again.
Thanks,
Daniel

cuartetoraro said:
Tried all four rom-like thingies I could download on the HTC page, all of them returning error 294...
Now what? try to somehow extract the .nbhs from the exes and and use customRUU.exe? Try to flash from SD card?
Please help... Any ideas... I really want to get rid from that original SPL3.29.0000 It's evil!!! I think it won't never let me flash again.
Thanks,
Daniel
Click to expand...
Click to collapse
sorry to hear that..
well, extract the .nbh from exe and flash it via sd card is the method that made me overwrite my hard SPL in the first place.
hmm, did your phone comes with operator brand, such as three or something?

-Rif- said:
sorry to hear that..
hmm, did your phone comes with operator brand, such as three or something?
Click to expand...
Click to collapse
No, it's HTC unbranded. Now, something strange here: the label behind the battery has the serial number: HT830GB06075 and the P/N (guess it's part number) :99HCY194-00, but to the left of the camera, another label with the part number: 36H00563-00M and below says DATE:061107(TB02)/US.
I don't know if that's normal, but it caught my atention because my phone seems to have been dissasembled (little label over screw is teared). Maybe my Kaiser isn't Australian after all...