I have been flashing roms to my rhodium with no problem. However, recently i reseted my phone and when it turned back on it was in bootloader moder(the tricolor screen) It stays in this screen no matter what I do. I have tried: removing the battery and putting it back on, flashing other roms, flashing stuck rom, and nothing it alway goes back to the bootloader screen. I flash using the sd card method and it goes thru the process of flashing(with the percent bar) It completes the process then i soft reset and back to bootloader!. same thing via usb, it completes the process but then it goes back to bootloader. I am desperate, Please HELP!
Related
I am having a problem that I hope someone can help me with.
I have an SX-66 with WM5 on it. The other day the device suddenly stopped booting. I can get the device to turn on, soft-reset, hard reset and get into bootloader mode, but whenever I try to boot the operating system it gets stuck on the colored stripe boot screen and just sits there showing the version numbers and nothing else. I have followed the instructions on the Wiki for downgrading but I still have the same problem. I have tried draining the battery fully and recharging but still no dice. I am even able to reflash the device with my laptop and it says it succeeds with the up/downgrade but then it just gets stuck again. If I try to install a 1.40 the device says that the flash is successful but then WM5 tries to boot again and I am stuck at the striped screen.
Can someone please help me out? Do I have a brick?
hey.. ive upgrade to new roms before.. however i tried going from the cingular 2.25 rom to summiters aku 2.3.. and it froze at 98% and was unable to finsh.. now I jsut tried downgrading and it froze again at 98%.. it won't complete anytthing.. help. please.
It's normal for it to seem to freeze at 98%, but it really will complete if you just wait a few minutes. No worries... just be patient.
If Stuck
hey if your phone is doesn't go through with the rom upgrade and doesn't push through and when you reboot you get stuck on the boot screen.
Put your phone into USB programming mode by holding the camera button down and doing a soft reset with the stylus. Then you will be able to load any rom you choose.
With regards to your frozen at 98 just give it time i would say don't unplug
same problem, still stuck
2nd time trying to load "Cingular_Custom_AKU2.3_Combo_Installer_V1.exe" ROM but still stuck at 98%...on the computer it says 100% and finishes but the phone is still stuck at 98%..tried to do a soft reset, but stuck at bootloader screen..
Help pleaseee!
Thanks!
Hello all,
as the title says, one of my touch diamond's is stuck in bootloader screen.
I didnt do anything in between it working and not working, it was on my desk, put it there working, got it 5mins later, and it was in bootloader screen (tricolor screen).
What i've already done to try and fix it:
flash it with the original HTC rom, flash completes succesfully, phone reboots to tricolor screen, so no solution there.
install mtty and format the phone, this completes, reboot the phone, again goes to the bootloader.
reflash the phone with original rom after cleaning it with mtty, flash again completes succesfully but when it reboots after flashing it just goes to bootloader again.
Tried to flash a Hardspl: stuck at 0% and stays there. so that doesnt work.
BUT! when in mtty i give the "boot" command, it DOES start to boot WM. but then again, when i turn the phone of, and on again, or it reboots because of first start after flash, it goes to bootloader again. The VOLDOWN button is NOT stuck, cause when it boots i can use the vol buttons perfectly fine.
Anyone got an suggestion in how to unbrick it? i have a second, perfectly working diamond here too, if that helps in any way.
Some more info ive just seen in mtty, when i told it to boot, it said ONE BAD BLOCK IN CE, remove block ---- to ---- (dont know the exact numbers anymore)
hi..i had something like that...
just download this.
"RUU_Signed_1_93OliNex_HSPL_UnsignedEdition"
it's only 1.7MB and it's will make it work.. atleast it did the job for me...
Hi,
My T mobile touch diamond stuck in bootloader screen? Any experties to help me please.
Thanks in advance.
EDIT: Can be closed, fixed it by going into recovery and wiping data/cache, never had to do that before in other flashes so didn't know it was needed
Hi guys,
first of all I'm not another first time flasher, I already succesfully put 4 other roms on my galaxy s but now I don't know what to do..
I came from jm5 and wanted to upgrade to jm8 today so I back upped everything and started the process, I thought I'd best follow richthoven's instructions so I first flashed the pit file + repartition, and then after pass, removed battery, back to download mode and put pda,modem,csc etc like always and started flashing.
Now my problem is from what I remember after the final reboot before odin sais pass the s logo dissapears and the phone boots into touchwiz, but now after the s logo dissappeared, my screen just stays black and after a minute or two odin sais passed, but there's nothing on my screen, and even after disconnecting and removing battery and try to boot it hangs on the s logo for a few minutes then a black screen with the backlight buttons highlighted.
Any help here would be greatly appreciated!
PS: I already tried the flashing procedure twice, same result
HI, im sort of a noob at this but i have been using the Custonexus rom for a cuple of days now and it have been running very good But yesterday when i tried to unlock the phone, the lockscreen didn't show up, the backlit buttons turned on as usual.
I turned off the phone, and did a factory reset. The phone booted up as normal with no problems. When i was up and running again, i booted into recovery to flash back to the stock rom from my backup just to be sure it didn't happened again. I did a factory reset and navigated to the backups but the backup was gone I rebooted the phone but it got stuck on the CN boot screen. What should i do? i have tried many times to reboot it but it always get stuck on the boot animation.
Install original lg kdz and redo everything.
You have to install the Stock (original) Firmware. Here is a HowTo: http://forum.xda-developers.com/showthread.php?t=2069723