Well as the title says is it possible to flash the phone without USB connection?
My USB connection has died, i can charge but that´s it
madness74 said:
Well as the title says is it possible to flash the phone without USB connection?
My USB connection has died, i can charge but that´s it
Click to expand...
Click to collapse
Hi,
Yes, it's possible.
You can flash by sdcard.
You can search here in the forum all bout how to do it
Thanks
Yiiiiiipi
Yeeees THX i´m saved
You'll only be saved if you already have hspl installed. You will not be able to flash via sd card (and no usb) unless you have hspl 1.56.Olinex installed.
ClydeB1 said:
You'll only be saved if you already have hspl installed. You will not be able to flash via sd card (and no usb) unless you have hspl 1.56.Olinex installed.
Click to expand...
Click to collapse
So if you have HDSPL already as mentioned by ClydeB1 then yes.
Only if you have HDSPL already then follow <<HERE>> for step by step instructions.
As much as I appreciate peoples responses, I feel we are only encouraging users to ask instead of searching for there answers.
This has been commented on loads of times before so need to to go over it again.
In future read the wiki, the stickies (i.e. threads at top of each forum)
Thread closed
Related
my computer is not reconizer this my Kaiser help me urgent
That's very little information. Has it ever worked? What have you changed recently? Does your computer even acknowledge that the device was plugged in? Is there an existing partnership?
You can try ending all partnerships between the computer and the phone. Without knowing what you've done, it's hard to give any more advice than that.
I'd also direct you to the Wiki and the Sticky...they both have lots and lots of information about the phone. I'm just assuming this has something to do with flashing a ROM on your phone because it's in the Upgrading forum and not the general Kaiser forum.
dont understand, i have windows xp and activesync dont have reconizer the kaiser!!! and dont flash the pda :S:S
Your English is obviously poor.
So, try this:
1) delete your devise from Activesync.
2) reboot your computer
3) plug in your phone to the computer.
Make sure you have the latest version of ActiveSync as well.
If I understand you correctly, you have not flashed your phone. Is that correct? If I am correct and you are still using the original ROM and software, then this question really belongs in the Kaiser forum and not the Kaiser Upgrading forum.
grizzley said:
Your English is obviously poor.
So, try this:
1) delete your devise from Activesync.
2) reboot your computer
3) plug in your phone to the computer.
Click to expand...
Click to collapse
DOnt Work!!!!!! :S flash without usb ???? how to???
x-club said:
DOnt Work!!!!!! :S flash without usb ???? how to???
Click to expand...
Click to collapse
HELLO I HAVE THE SAME TROUBLE WITH MY TILT THE USB IS NOT WORKING SO I HAD TO USE MY SD CARD AND FLASH MY PHONE ITS KIND HARD BUT ONE YOU READ AND DO STEP BY STEP IT REALLY EASY.IM SENDING YOU THI SITE TO READ ON HOW TO DO THIS HOPE THIS HELPS AND IF SO PLEASE LEAVE A COMMENT ON HOW I HELPED I PROMISED THIS SITE SINCE THERE ARE FEW THAT TAKE THE TIME TO QWORK WITH YOU FOR FREE I SAID I WOULD TRY TO DO THE SAME.. A SPECIAL THANKS TO ALLTHE WAY FOR TEACHING ME.....
http://forum.xda-developers.com/showthread.php?t=336158
Flashing using MicroSD Card - xda-developers HOPE THIS IS WHAT YOUR LOOKING FOR..GODBLESS....
sexylatin1 said:
HELLO I HAVE THE SAME TROUBLE WITH MY TILT THE USB IS NOT WORKING SO I HAD TO USE MY SD CARD AND FLASH MY PHONE ITS KIND HARD BUT ONE YOU READ AND DO STEP BY STEP IT REALLY EASY.IM SENDING YOU THI SITE TO READ ON HOW TO DO THIS HOPE THIS HELPS AND IF SO PLEASE LEAVE A COMMENT ON HOW I HELPED I PROMISED THIS SITE SINCE THERE ARE FEW THAT TAKE THE TIME TO QWORK WITH YOU FOR FREE I SAID I WOULD TRY TO DO THE SAME.. A SPECIAL THANKS TO ALLTHE WAY FOR TEACHING ME.....
http://forum.xda-developers.com/showthread.php?t=336158
Flashing using MicroSD Card - xda-developers HOPE THIS IS WHAT YOUR LOOKING FOR..GODBLESS....
Click to expand...
Click to collapse
how to format microsd and is work in card 2GB?
x-club said:
DOnt Work!!!!!! :S flash without usb ???? how to???
Click to expand...
Click to collapse
If this is the best you can come up with after people have tried to help then I guess you haven't read the WIKI yet.
It's obvious English isn't your first language, but if you don't read AND understand the WIKI then you will break your phone.
If necessary get a friend to help with translation. Or post your question in English and your own language - then maybe someone on the forum who speaks your language can help out.
I posted this deep in another thread (a sticky), but I think it fits better as a new topic because it is not specific to that other thread. I'll make a note in the other thread to avoid duplicates.
Okay....
I'm absolutely new to the world of ROMs and SPL, HSPL, SSPL and USPL - but I've been doing my homework today and I've read all of the wiki links more than once.
Before diving into it and making some dumb newbie mistake, I wanted to run a couple of things by you guys.
I have the German o2 ROM 1.14.207.2 (24011) GER.
I don't want the o2 branding, but I still want it in German.
So, I want to flash RUU_BlackStone_HTC_GER_1.14.407.3_Radio_52.49a.25. 26_1.09.25.14_Ship.exe
My understanding is that since these are both stock ROMs (at least I believe they both are, right?), my stock SPL should accept the new ROM without any problems. In other words, I don't need anything like USPL. Am I correct? Or do I actually need USPL because the new ROM is not from my current vendor which is o2?
Based on what I learned reading all the info, this is what I plan to do:
Turn off my phone, remove SIM and MicroSD
Enter boot mode (tricolor screen)
connect phone via usb to WMDC (Vista 32-bit). The settings are set to ALLOW usb connections
Disable my antivirus program
Disable all power saving modes, screensavers etc.
Run the RUU Ship.exe mentioned above as administrator
Follow instructions until device reboots
So now my warranty should still be fine. If I have to send the device in for repair, to I need to put the o2 ROM back on it?
Thanks for your help (and patience) with a newbie that scared to turn his HD into a brick. I think I'll wear diapers while I'm flashing - just in case.
I'll wait for some responses before I tackle the 7 steps above.
Chris Cross said:
My understanding is that since these are both stock ROMs (at least I believe they both are, right?), my stock SPL should accept the new ROM without any problems.
Click to expand...
Click to collapse
No, thats not true at all. For instance you can't flash a WWE Rom over a German Rom, although they are both stock roms. There is a country specific code (CID). The stock SPL is checking this, so its impossible to flash roms coming from another country.
I'm not sure if the stock SPL also checks the vendor/operator, but I guess it does.
Chris Cross said:
In other words, I don't need anything like USPL.
Click to expand...
Click to collapse
You should just try it. The SPL will tell you whether it accepts the rom or not.
Chris Cross said:
Based on what I learned reading all the info, this is what I plan to do:
Click to expand...
Click to collapse
First of all you should consider which SPL you want to use. If you really just want to flash this new rom, USPL is good for you, if you are going to change your rom more frequently then HSPL is the way to go.
Instructions on how to use this SPLs are given in the appreciate threads (with many comments of other users), so you should look them up (again).
Chris Cross said:
So now my warranty should still be fine.
Click to expand...
Click to collapse
You warrany is fine, if the operator/vendor gets the device with the rom he shipped it to you (or any official upgrade provided by this operator/vendor). If you flash the official htc german rom, you might loose your warranty.
Chris Cross said:
If I have to send the device in for repair, to I need to put the o2 ROM back on it?
Click to expand...
Click to collapse
Yes, normally you do.
Chris Cross said:
Thanks for your help (and patience) with a newbie that scared to turn his HD into a brick.
Click to expand...
Click to collapse
If you are doing all as mentioned in the appreciate instructions nothing extraordinary should happen. I have flashed my HD for over 15 times in the last few days.
Chris Cross said:
I think I'll wear diapers while I'm flashing - just in case.
Click to expand...
Click to collapse
Normally that shouldn't change anything .
Chris Cross said:
[*]connect phone via usb to WMDC (Vista 32-bit). The settings are set to ALLOW usb connections
Click to expand...
Click to collapse
Read the USPL thread carefully - you have to disable allow usb connections. In vista you will probably find that you will have to downgrade the USB drivers - that is dealt with in Post 69 of the USPL thread - see also post 1 of http://forum.xda-developers.com/showthread.php?t=291723
apd said:
Read the USPL thread carefully - you have to disable allow usb connections. In vista you will probably find that you will have to downgrade the USB drivers - that is dealt with in Post 69 of the USPL thread - see also post 1 of http://forum.xda-developers.com/showthread.php?t=291723
Click to expand...
Click to collapse
yes, I had read that about disabling usb connections. I just thought that if I did not need USPL then I could leave usb connections enabled and try the other german ship.exe rom. Anyway, I think might need to alter the SPL anyway.
THANK YOU ALL for your responses. They were very helpful and it is time for me to get working on it when I get home.
I will post back my results.
Well, everything worked out fine.
I ended having to use USPL because my SPL did not accept the new stock ROM (same language, but different vendor: o2 vs. non-branded).
I did have to downgrade my vista drivers for it to work. I followed all the wiki instructions and had no problems.
Thanks again for the help.
Sercurity Unlocker
Will the blackstone have to be security unlocked to flash cooked ROMs or will it be done in the HSPL?
primbcadman said:
Will the blackstone have to be security unlocked to flash cooked ROMs or will it be done in the HSPL?
Click to expand...
Click to collapse
Security unlock matters for radio flashing only.
Security unlocker.
stepw said:
Security unlock matters for radio flashing only.
Click to expand...
Click to collapse
thanks for reply. pity tho after bought unlocked thc touch hd will have to pay for that again just to get security unlocker, like I did for touch pro.
Hi! I've flashed official firmware and SPL on my AT&T Tilt, cause a lot of problems in non-official firmwares (occasional hard-resets, freezes, etc). Now phone is working ok, and I wan't to come back to cooked roms, but I've no success in flashing the HardSPL, because my USB jack is broken in phone (only charging is working). I've only a possibility to flash via SD. I have tried to load KAISDIAG via SD, but SSPL says only "Loading..." and nothing else.
Is there any possibility to flash HardSPL via SD, or I've to resolder my USB jack?
Help me, please
edit I don't know.
obion said:
Hi! I've flashed official firmware and SPL on my AT&T Tilt, cause a lot of problems in non-official firmwares (occasional hard-resets, freezes, etc). Now phone is working ok, and I wan't to come back to cooked roms, but I've no success in flashing the HardSPL, because my USB jack is broken in phone (only charging is working). I've only a possibility to flash via SD. I have tried to load KAISDIAG via SD, but SSPL says only "Loading..." and nothing else.
Is there any possibility to flash HardSPL via SD, or I've to resolder my USB jack?
Help me, please
Click to expand...
Click to collapse
You can only change your Hardspl from your SD card. You can only initially flash Hardspl from your Pc .
So, the answer is: you have to repair your USB to flash HardSPL.
Am I right?
obion said:
So, the answer is: you have to repair your USB to flash HardSPL.
Am I right?
Click to expand...
Click to collapse
You are right, sorry I wasn't clear.
Very bad
you can use jump SPL and then flash hard SPL from SD
badillo said:
you can use jump SPL and then flash hard SPL from SD
Click to expand...
Click to collapse
Providing you had the foresight download and maintain jumpspl on your phone prior to your usb port breaking
but jumpspl can still be "downloaded and maintained" on the device using the mobile browser to access the internet over wifi and/or the data connection...?
so would i be correct if i summarized all the posts in this thread by concluding that a broken usb port is not a hurdle in getting hard spl on your phone?
cuz badillo says hard spl can be applied from sd...and denco7 says that jumpspl is required to get the process started...and i propose that jumpspl can be downloaded to the device by wireless means...
or is this conclusion of mine incorrect?
hmm jumpspl on a sd and copy to the fone?
i honestly think thas jumpspl, and sdcard update cant work together.
but please prove us wrong, it makes unlocking a lot more easy
i want an answer to this topic!!
I have a problem which I need to change hardspl also
thank you very much
You have to have a usb sync for first h-spl 3.29 after that you can read the instructions in h-spl breakdown by Dave Shaw in Sticky ROM dev and surely enough you can flash via SD
I mean i want an answer to post #9, since my usb port is broken.. i can't do usb sync.
kyniemxotxa98 said:
I mean i want an answer to post #9, since my usb port is broken.. i can't do usb sync.
Click to expand...
Click to collapse
Look HERE
JumpSPL
7Zip to extract zip files attached bellow! Best of luck to you!
Thanks for your reply Philux-X,
However, this is for the Kaiser, I was looking for something more general as I have an HTC Diamond instead. My research concluded that HardSPL via SD is not possible. I was wondering if any smart people here know of any alternatives.. I'm willing to take risks.
kyniemxotxa98 said:
Thanks for your reply Philux-X,
However, this is for the Kaiser, I was looking for something more general as I have an HTC Diamond instead. My research concluded that HardSPL via SD is not possible. I was wondering if any smart people here know of any alternatives.. I'm willing to take risks.
Click to expand...
Click to collapse
Bottom line is , you can only upgrade your hardspl via SD Card, you can only hardspl from stock spl via usb connection.
Believe me a lot of smart people have tried for a while.
kyniemxotxa98 said:
Thanks for your reply Philux-X,
However, this is for the Kaiser, I was looking for something more general as I have an HTC Diamond instead. My research concluded that HardSPL via SD is not possible. I was wondering if any smart people here know of any alternatives.. I'm willing to take risks.
Click to expand...
Click to collapse
You are in the KAISER Forum! You need to be asking this in the Diamond Forum! I only gave you that info assuming you were a Kaiser user! Anything Kaiser will only brick your device for sure!!!!!!!!!
Update your signature to what your device credentials are so people are able to help you better! Take mine and Denco7's for example. If more people had their signatures setup, it would make it so much easier to give out advice!
EDIT: If usb is broken how are you charging the device?
The Diamond does not require the launch of a jump spl, the hardspl package by olinex has all the required files in it. But it must be run from the PC which requires an active sync connection
And Diamond user stop double posting, go to Diamond section and do your research........
Denco7 has answered you in 2 threads yet you still coming back to Kaiser section...
I have read about 10 pages of charging and syncing problems but they weren't like mine. I flashed hardspl 3.34 and then it all went bad. When it is turned on it wont charge from wall/car/usb. When I put it into bootloader, it seems like my computer recognizes it (it asks me if I want to safely remove hardware) but windows mobile device center doesn't say it's connected, nor does it show up in computer. I did a hard reset and all that. It still has original 6.1 rom. Should I flash another spl? Or another rom? Any suggestions? I really hope I didn't f up my tilt. I finally got it after I bricked my wizard a year ago.
thedon809 said:
I have read about 10 pages of charging and syncing problems but they weren't like mine. I flashed hardspl 3.34 and then it all went bad. When it is turned on it wont charge from wall/car/usb. When I put it into bootloader, it seems like my computer recognizes it (it asks me if I want to safely remove hardware) but windows mobile device center doesn't say it's connected, nor does it show up in computer. I did a hard reset and all that. It still has original 6.1 rom. Should I flash another spl? Or another rom? Any suggestions? I really hope I didn't f up my tilt. I finally got it after I bricked my wizard a year ago.
Click to expand...
Click to collapse
Well, if you are in bootloader and you got the USB sign on it you are ok. Try to flash another rom or reflash your stock rom.
Yes bootloader seems to work and says usb. I think what I did was flashed hardspl 3.29 following the directions in the "flashing your first kaiser rom" thread. But when I flashed 3.34, I flashed it using usb and not an sd card like it said. I just want to go back to original spl and rom.
thedon809 said:
Yes bootloader seems to work and says usb. I think what I did was flashed hardspl 3.29 following the directions in the "flashing your first kaiser rom" thread. But when I flashed 3.34, I flashed it using usb and not an sd card like it said. I just want to go back to original spl and rom.
Click to expand...
Click to collapse
Just look here: http://wiki.xda-developers.com/index.php?pagename=Kaiser_ROMs
Hope that helps
I flashed that rom and it still does the same thing.
thedon809 said:
I flashed that rom and it still does the same thing.
Click to expand...
Click to collapse
Let's try this one my friend http://forum.xda-developers.com/showthread.php?t=335568 probably you can revert back to the original spl and stock rom
What about these steps?
11. Download pof's SSPL-KAIS.exe and copy it to your phone
12. Run SSPL.KAIS.exe from your phone (make sure you do this on your actual device and not your PC)
I can't do them because my phone won't sync to my computer.
thedon809 said:
I think what I did was
Click to expand...
Click to collapse
That bit made me shiver.
stuntdouble said:
That bit made me shiver.
Click to expand...
Click to collapse
lol, I know that's exactly what I did. I was just saying, that I think that has something to do with it not charging and syncing. I'm not sure though, because I'm not a pro at flashing and all that. I can rebuild an engine, but I can't flash a stupid rom on a phone . Whatever I have to do to fix it, will have to work the next time because I only have about 60% battery left.
thedon809 said:
What about these steps?
11. Download pof's SSPL-KAIS.exe and copy it to your phone
12. Run SSPL.KAIS.exe from your phone (make sure you do this on your actual device and not your PC)
I can't do them because my phone won't sync to my computer.
Click to expand...
Click to collapse
Anyone have any suggestions on what to do about this? Will using my sd card work? Sorry about the noob questions. I know what it's like helping noobs that have no clue what they are doing.
thedon809 said:
Anyone have any suggestions on what to do about this? Will using my sd card work? Sorry about the noob questions. I know what it's like helping noobs that have no clue what they are doing.
Click to expand...
Click to collapse
You can upgrade SPL via SD but you will need a WM donor phone (spare) or a card reader to format the sd card. Try that and let us know if that worked
gmaniac2008 said:
You can upgrade SPL via SD but you will need a WM donor phone (spare) or a card reader to format the sd card. Try that and let us know if that worked
Click to expand...
Click to collapse
My hp laptop conveniently has an sd card reader.
Ok, to install from sd card, I put stock att hardspl RUU_signed.nbh and KAISDIAG.NBH into sd card, pop it in and go to bootloader? Correct?
thedon809 said:
Ok, to install from sd card, I put stock att hardspl RUU_signed.nbh and KAISDIAG.NBH into sd card, pop it in and go to bootloader? Correct?
Click to expand...
Click to collapse
Follow the instructions of how to flash via sd card from here: http://forum.xda-developers.com/showpost.php?p=2741200&postcount=1
Do I have to change the name of the att hardspl to KAISIMG.NBH?
thedon809 said:
Do I have to change the name of the att hardspl to KAISIMG.NBH?
Click to expand...
Click to collapse
No.
(message too short so adding more letters to post comment.......)
hey,
i know this might sound like a stupid question but i am confused...
i tried flashing hardSPL but it wouldn't.
So it just keeps at 0% for more then half an hour. then i just disconnected it.
I have the RHOD300 version and used the GSM version.
What do i do wrong?
i do not need to SIM-unlock before right?
and the CID-unlock is the same as the hardSPL i thought? so why can't i flash?
thanks nick!
Correct, you don't need to SIM-unlock first. Check the troubleshooting section near the start of the sticky HardSPL thread, there are lots of suggestions of things to try there.
np progress
hey
firstly thanks for yozr fast response.
i read the troubleshooting section and everything but i could not find a solution to my problem
i am able to connect the phone and put it in bootloader and then flash it.
everything works as it did on my kaiser when i used to flash it...
so i get the grey screen with the progress bar on top but there is no progress! ive been waiting for half an hour but still no progress.
so i dont know how to go on now...cuz i need hardSPL for flashing all other roms
could someone help me here?
and is there a way to flash it via sd card?
couldnt find the nbh
thanks nick!
You can't flash HardSPL via your SD card, no, sorry. You really need to post up on this in the HardSPL thread though, rather than having a separate thread here.