I need to remote troubleshoot a friend. He put a wrong ROM, i think, and now OS is moving very slowly, does not have GSM, WiFi and neither can connect USB to a Windows 7. Bluetooth works.
Qtek 9100 G3
The boot is:
IPL 1.01
SPL 2.17
OS 1.5.4.2
(no radio)
I do not know if the USB problem is related to ROM or is a communication problem / driver with Win7.
What am I after, and here I need your advice, if is possible to do a ROM flash from the memory card?
Also ANY suggestion is more than welcome.
Related
I have a T-Mobile Compact II which has turned into a brick.
I Flashed the ROM with the HTC Touch ROM which run perfectly, no problems at all. Then i found a newer version of the same software, which Flashed the ROM (no problems encountered on the PC Screen) but when i come to hard reset the device it sticks at boot screen with the following
IPL 2.06
SPL 2.06.0000
GSM 02.19.21
OS 6.0.0.0
and will not go any further
I have tried the boot load (powering up with camera button pressed)
and get the following
IPL 2.06
SPL 2.06
USB
On the 3 colour screen.
i know the PC sees the device but cant get any communication to or from the device with active sync
Any ideas how to restore this fault.
Thanks Steve
Sorted
i have sorted my problem out. It turns out that i could not repair through a PC running Vista. Sorted on a XP machine
Bricked My Mda Compact 2
Last night I flashed my MDA Compact II with a ROM in this forum. It's from the thread: Tuning ROM 2.6.2.27 MDA CHARMER(MDA COMPACT II). The ROM update seemed to go okay, but now the Charmer won't boot. All I get is the splash screen, which says:
IPL 1.12
SPL 1.12.0000
OS 2.6.2.27
the i was told by a senior menber to flash it with BUTTON 1.05 (which i did)
and now BATTERY IS NOT CHARGING
and now i have
ipl 1.01
spl 1.12.000
gsm 01.12.10
os 1.5.4.2
NOW I HAVE REALISED THAT I HAVE USED ALL WIZARD FILES ON CHARMER WHICH IS THE ROOT CAUSE OF ABOVE MESS.
i have checked usb cable , main power charger with other pda and it was working ok , i have charged my battery on external charger.
MDA compact is not recognizes if battery
can it be a problem with registry ?
PLZ HELP
have a charmer. I tried to put wm6. but spl and ipl was 1.12. the phone start up and hang when installing some cabs. i restart ir and it allways crashes at t-mobile logo. i updated the rom to aku 3.3. all ok. but continues chashing on t-mobile logo. i try a hard reset. gives me a fat error. I try to put the rom from prophet to try to format it. but that rom upgrade reach 95% and stop. give me a error. this nbf file cannot be used to upgrade this device. I tryed all types of roms. most of them crashes at some point and give me that error. the rom aku 3.3 german and wwe, install perfect. I think that is the only roms I can send to my charmer. but i can´t format whith that rom, fat error. I have 3.08 spl ipl 1.12 because i sent an old charmer rom. ipl downgrade, but spl don´t. do you think my device can be protected?? I dont know that to do more, to bring the charmer back to life. will sd card method work? please help me.
Charmer dead after wm6 update whitout cid unlocking
Hi @all
i have the same problem.
iam stuped and make an wm6 update from ipl1.12 and i have forgot to cid unlock my charmer.
after the update to wm6 all looks like good. the bootscreen from wm6 i have see.
after the reset the charmer hangs at slashscreen.
now i make a update to aku 3.3 ger.
that works but hangs in the t-mobile spaschscreen.
i have tray all downgrading methodes i have read here but nothing works.
jet i have a ipl 1.12. and spl 3.08.
I think only a sd-card rom update works. but i dont have found an sd-card rom to use.
sorry to my bad english.
please can anybody help me?
cu AxelD
Is my phone already dead? Please help me!
Hi, I have a similar may be the same problem!
My phone is a German t-mobile mda compact 2
First I work with “lokiwiz v.02” to unlock the SIM, and it works really well.
Then I installed “Charmer_Touch_ver._2.1” and I could calibrate the screen, and after that Win Mobile 6 installed all the extra stuff automatically. After that the device made a reboot, but it stop at the t-mobile boot screen.
Because the bootload modus is still running, I installed the newest original t-mobile software “RUU_compactII_AKU3.3_38222_382117_026921R_TMO_DE_GER_Ship” but this also didn’t solve the problem.
Hard reset didn't work and always says "Format is
The Start screen shows me this information:
IPL 3.08
SPL 3.08.0000
GSM 02.69.21
OS 3.8.2.22
Is my phone really dead or could someone tell me a trick to reactivate it?
I think noone have a solution for us. I tried to send commands to phone whith mtty. and I can´t send. I don´t know why. so f we cannot send commands the sd card method will not work too. the only olution is to jtag the charmer. but can´t find any pinout information. if anyone knows this informtion, please help.
I've been trying to find a thread that addresses my issue but have'nt been able to find anything addressing my issue.
I wanted to upgrade my 8125 G4 (IPL/SPL 2.25.0001) to WM6 so I tried the guide for "newbies".
I have windows XP and Activesync 4.45. I was able to establish a connection with my 8125. I ran the HardSPL and it confirmed my device is G4 and it went to the utility.
I followed the utility and was able to reconnect and reestablish connection with activesync. after rebooting my phone the IPL is 2.21.0001 but the SPL is still 2.25.0001. Can you tell me why it did'nt change to
2.21.olip?
I then tried rerunning HardSPL but when the utility asked me to reconnect and establish connection with activesync activesync does not discover the phone. Otherwise am able to use my phone just fine and can even activesync with my laptop.
I did not continue to other steps for fear of bricking my phone since the guide says not to continue if SPL isn't 2.21.olip.
Can anyone please help me get back on my way to WM6?
Thanks
my phone is:
Rom 2.25.11.1 wwE
radio 02.25.11
Protocol 4.1.13.12
ExtRom 2.25.11.102
brent39902 said:
I've been trying to find a thread that addresses my issue but have'nt been able to find anything addressing my issue.
I wanted to upgrade my 8125 G4 (IPL/SPL 2.25.0001) to WM6 so I tried the guide for "newbies".
I have windows XP and Activesync 4.45. I was able to establish a connection with my 8125. I ran the HardSPL and it confirmed my device is G4 and it went to the utility.
I followed the utility and was able to reconnect and reestablish connection with activesync. after rebooting my phone the IPL is 2.21.0001 but the SPL is still 2.25.0001. Can you tell me why it did'nt change to
2.21.olip?
I then tried rerunning HardSPL but when the utility asked me to reconnect and establish connection with activesync activesync does not discover the phone. Otherwise am able to use my phone just fine and can even activesync with my laptop.
I did not continue to other steps for fear of bricking my phone since the guide says not to continue if SPL isn't 2.21.olip.
Can anyone please help me get back on my way to WM6?
Thanks
my phone is:
Rom 2.25.11.1 wwE
radio 02.25.11
Protocol 4.1.13.12
ExtRom 2.25.11.102
Click to expand...
Click to collapse
Did the HardSPL completed successfully ? did the screen go white for awhile.If it didn't,then rerun the HardSPL again,but disable or shut down any Antivirus or firewall and any other heavy application or program running in the background while applying HardSPL sometimes create problems also.Reset the phone,reset the pc and close all programs/applications from the desktop through 'Task Manager' and don't surf the net or do any other operation during HardSPL,let it complete the whole process,if the screen goes white,don't panic its the essential part.
HardSPL did complete successfully.
The screen on the phone did change to white.
I had the windows firewall off and antivirus disabled also. i think i did have internet explorer open at the time however.
I will try again running it with no background programs running and see what happens.
Are there any known services or background applications that prevent a successfull HardSPL installation?
hi...
After i tried to update my T-Mobile Vario to high version of WM5, my device worked with out Radio ROM( GSM ROM), not connected by USB with active syn. , when i entered to color screen my computer make beep means conected but when i wana upgrade SPL & WM6 or downgrade to WM5 connection failed..
thnx
Which is your device,G3 or G4 ? First post the vital data of the phone,like IPL/SPL ? which rom were you exactly trying to flash and how you were trying to flash ? only then its possible to help you out.
i am problem whit my qtek 9100 (htc wizard)
my qtek is flashing whit rom win-mobile v4 , and the os is very slow, wifi is not work , usb too, the bluethoo is ok is working im sync on my computer whit bluethoo but the upgrade tool on www.qtek.nl , for the original updated rom windows m 5 is not work, error message is , problem communication whit computer and pocket pc, but the pocket pc is sync whit my computer...
i need help for the ultimate method for flashing whit a bluethooth method , im repeat usb is not working , please i need help or the qtek is go to trash... snif
os 1.5.4.2 wm 5
ipl 1.01
spl 2.17
g3
thanks for your helping
my mail is [email protected]
Hi pretty sure you can't flash over bluetooth. If you know someone else with a wizard they could back up there rom onto an SD card which could then be loaded onto your device. Hope this helps
Hi pretty sure you can't flash over bluetooth.
f you know someone else with a wizard they
could back up there rom onto an SD card
which could then be loaded onto your device.
Hope this helps
hi, i have same problem with htc wizard, ipl 1.01 spl 2.17 os 1.5.4.2, and it is stuck in startup, i can`t make hard reset, i cant backup rom to sd because cid is locked. So i have to find who has same phone ant ask to send me rom backup to me?
sorry, my english is not very good...