irretrievable ERROR?PLZ help!!! - Touch Diamond, MDA Compact IV General

After cooking the new rom with my p3700 with 100% finished,but it sudddenly
comes as a error.Then i try to softreset it and now,the phone stuck on the bootloader screen .Its totally irresponsive to any action,not work in cooking a rom with my pc nither restoring it.any solution?FORGIVING ME I'm fresh.
.

kit03190 said:
After cooking the new rom with my p3700 with 100% finished,but it sudddenly
comes as a error.Then i try to softreset it and now,the phone stuck on the bootloader screen .Its totally irresponsive to any action,not work in cooking a rom with my pc nither restoring it.any solution?FORGIVING ME I'm fresh.
.
Click to expand...
Click to collapse
Have you tried a Hard Reset?
Have you unlocked your device first?

mr.horndoctor said:
Have you tried a Hard Reset?
Have you unlocked your device first?
Click to expand...
Click to collapse
I have tried hundred times to Hard Reset.And it's not working.
unlock my device?I'm not sure.I've just cook a non-official rom to my device.
for the first time.and met this sreious problem.ORZ LOL

Doesn't matter what you did. If you can still get into bootloader then you can flash from there. Either flash a stock ROM or use mtty to flash another ROM.

supersanj said:
Doesn't matter what you did. If you can still get into bootloader then you can flash from there. Either flash a stock ROM or use mtty to flash another ROM.
Click to expand...
Click to collapse
i think so .yet my device doest not response my PC at all'

Here's what you need to do before you connect your usb cable to the diamond:
1. Download MTTY from here:
http://forum.xda-developers.com/attachment.php?attachmentid=208457&stc=1&d=1248437219
2. Download any ROM you want
3. Right click the ActiveSync icon and click "Connection Settings"
4. Untick "Allow USB Connections"
5. Now hold the volume down button and press the reset using the stylus.
6. It will come up with the tri-colour bootlader screen and at the bottom it should say "serial".
7. Connect the usb cable and the "serial" should change to "USB"
8. Run the MTTY program.
9. Select "USB" from the "Port" Dropdown menu. Then press "OK"
10. Press the "Enter" key on your keyboard to get a prompt.
11. Type "set 14 0". and press Enter.
12. Type "task 29" and press Enter.
13. Hold the Diamond in your hand and get ready to press and hold down the volume down key. Don't disconnect the usb cable.
14. Type "task 8" and press Enter. This will restart the phone so as soon as you press Enter press and hold down the volume key to get into bootloader again.
15. It will show "USB"
16. Flash the ROM you downloaded using the RUU.
17. After the flash do a hard reset (volume down and centre buttons pressed then reset using stylus. When prompted select "volume up". Don't press the "volume down button as it will also delete your internal storage.
18. You're done.

supersanj said:
Here's what you need to do before you connect your usb cable to the diamond:
1. Download MTTY from here:
2. Download any ROM you want
3. Right click the ActiveSync icon and click "Connection Settings"
4. Untick "Allow USB Connections"
5. Now hold the volume down button and press the reset using the stylus.
6. It will come up with the tri-colour bootlader screen and at the bottom it should say "serial".
7. Connect the usb cable and the "serial" should change to "USB"
8. Run the MTTY program.
9. Select "USB" from the "Port" Dropdown menu. Then press "OK"
10. Press the "Enter" key on your keyboard to get a prompt.
11. Type "set 14 0". and press Enter.
12. Type "task 29" and press Enter.
13. Hold the Diamond in your hand and get ready to press and hold down the volume down key. Don't disconnect the usb cable.
14. Type "task 8" and press Enter. This will restart the phone so as soon as you press Enter press and hold down the volume key to get into bootloader again.
15. It will show "USB"
16. Flash the ROM you downloaded using the RUU.
17. After the flash do a hard reset (volume down and centre buttons pressed then reset using stylus. When prompted select "volume up". Don't press the "volume down button as it will also delete your internal storage.
18. You're done.
Click to expand...
Click to collapse
I am able to cook a new rom now.but failed and it said corrupted image.how can deal with it?

What ROM kitchen are you using?

supersanj said:
What ROM kitchen are you using?
Click to expand...
Click to collapse
thanks for helping!my problem is solved!
one problem is left....
the ram always used above 90%hard to do anything.

kit03190 said:
thanks for helping!my problem is solved!
one problem is left....
the ram always used above 90%hard to do anything.
Click to expand...
Click to collapse
Open File Explorer and navigate to Task Manager in the main Windows folder and click to open. Then click on the right softkey and highlight view and then click on processes.
Then you can see what processes are running and what is using up ram.
Then use an app like CleanRam or MemMaid to stop/close processes and reclaim/free up used ram.

Related

Emergence!!!Siemens sx66 radio rom upgrade problem!

I download a radio rom 1.15 and try to upgrade, after that, my PDA just open as USB when it is docking and sieral after take it out from the docking. whatever how to reset it, still could not start like before. maybe i damaged all the ROM Image? and anyone can help me to recovery it? Thanks.
Hard Reset ????
andyxiaxda said:
I download a radio rom 1.15 and try to upgrade, after that, my PDA just open as USB when it is docking and sieral after take it out from the docking. whatever how to reset it, still could not start like before. maybe i damaged all the ROM Image? and anyone can help me to recovery it? Thanks.
Click to expand...
Click to collapse
Did u try a Hard Reset? Record + Camera/Multimedia + Soft Reset
Yes, I tried hard reset, but still same thing.
Stevo.Mksr said:
Did u try a Hard Reset? Record + Camera/Multimedia + Soft Reset
Click to expand...
Click to collapse
Yes, i tried hard reset. nothing change.
and i searched this forum long time, still did not find a solutions.
still waiting for help.
thanks.
Stuck In Bootloader
andyxiaxda said:
I download a radio rom 1.15 and try to upgrade, after that, my PDA just open as USB when it is docking and sieral after take it out from the docking. whatever how to reset it, still could not start like before. maybe i damaged all the ROM Image? and anyone can help me to recovery it? Thanks.
Click to expand...
Click to collapse
OK.. this is a copmmen problem.. You are stuck in the bootloader...
Try the WIKI for help...http://wiki.xda-developers.com/index.php?pagename=BA_FAQ_Bootloader_mode
then try to use mtty.. (search for it using the search button above!)
Good Luck.. All is not lost!
1. Download Romupdate v1.11a
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete) kill two processes rapimgr.exe and wcescomm.exe
3. put your device into Bootloader Mode by pressing Power + Record Button and Soft Reset.
4. Run Romupdate v1.11a (from downloaded)
5. from left top corner drop down menu Port: Choose WCEUSBSH001 (If you only see COM 1 and COM1 try unplugging the USB and replugging it)
6. press OK button
7. type "set 14 0" without the quotes in blank window that showed up to tell bootloader to boot the OS after reset.
8.press enter to execute
9. on next line you will see:
HTCST ÚÈÒHTCEUSB>
10.type "task 28" (no quotes) right after > sign to get your device formatted
11.press enter to execute, you gonna see:
DOC_format_HW+
DOCInfoTableinitHW+
Binary0:dwSize=80000
BINFS0:dwSize=0
FAT0:dwSize=1000000
FAT1:dwSize=2BA0000
All:dwSize=3C20000
USB>
12. type "task 0" (no quotes) right atfter > sign to ask your device reboot
13.press enter to execute the command
14. take the device out of the cradle, and manually reset it if it does not do that already.
good luck.

ROM Upgrade

I Recentley Tried To Upgrade To The Latest ROM So I Went To The O2 UK Website And Downloaded Xda_IIs_Upgrade_v140242.exe, About Half Way Through The Upgrade My Computer Froze And I Had To Re-Start It.
Now My XDA IIs Wont Turn On And When I Put It In Its Cradle The Power Light Turns Red....Not Orange But Red. I Have Tried Running Xda_IIs_Upgrade_v140242.exe Again But I Just Get;
ERROR 101: CONNECTION ERROR
Is There Anything I Can Do Or Is It Terminal?
Thanks
huh!
can u enter into bootloader mode? press POWER + NOTES + RESET BUTTONS? if it does, it can be upgraded again........ try it
No Luck
Just To Make Sure, The Notes Button Been To The Left Of The Speaker? I Have Tried Holding All 3 At Once And Nothing Happens. I Dont Have My Mains Cable In, Will That Matter?
Fingers Crossed
After Removing The Battery And Re-Inserting It And Following Your Instructions I Am Doing An Upgrade At The Moment, I Will Let You Know How It Goes....Thanks For Your Help
Error 112 : Ce Rom Update Error
ERROR 112 : CE ROM UPDATE ERROR
Any Ideas?
i see!
remove the battery for about 30 mins. after that reconect and then see if it has power! try POWER + RESET. f no luck, then the problem is in the boot process mode! i think there is a way to revive it somewhere here........ just try to search the forum...... gud luck let me know if you found a way!
error
colhatty said:
ERROR 112 : CE ROM UPDATE ERROR
Any Ideas?
Click to expand...
Click to collapse
are you upgrading from the same provider with the previous rom? meaning from O2 to O2 not O2 to imate roms or other roms..............
try mtty method, you may have screwed a lil your device
1. Download mtty from the attachment
2. Stop ActiveSync, by Task Manager (press Ctrl + Shift + Escape) kill two processes rapimgr.exe and wcescomm.exe
3. put your device into the cradle
4. Run mtty (from downloaded) Choose WCEUSBSH001 (or just USB in port) and press OK
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
After this procedure reflash
Thanks xplode,
I had a simialr problem as colhatty where my Xda IIs was just displaying USB when plugged into the cradle, following your steps I was able to reset the device and get WM 2003 SE to boot.
PDA2K dead
while upgrading with several attempts my PDA2k is almost broken it has only the colored page and nothin else , i treid your SW actually i dont know exactly how to use for example is thier any thing else to do after righting the commands
/ shall i save it? what to do? in all means nothin happen any help
HOWTO: Reinstall existing ROM without touching Extended ROM or Upgrading/Downgrading
The following methods allow you to get rid of all user data on the device (except for memory recognised by the resident system as being storage cards).
>>> METHOD A -> Device Only (recommended, faster)
1) Use two fingers to simultaneously press the RECORD and CAMERA buttons of the phone (on the phone's left side). Whilst these two buttons are depressed, use the stylus to click the soft-reset button underneath the phone - keep the two buttons depressed until the boot loader screen appears.
2) This should enable three options on the boot screen. These options allows a YES/NO response. Use the RECORD and CAMERA buttons to navigate between the options, and switch the YES/NO values. Set the following:
1] Enable KITL: NO (this is a debug tracing option which isn't required, except possibly for developers)
2] Format Registry Hive: YES (clears the registry)
3] Format Storage: YES (formats the internal memory: "\" directory, and under "\RamDisk\". Items under any storage card "\Storage Card\" are not formatted).
3) Once these options are set, press the MAIL button (in between today and the Pocket IE button) to confirm these options, and continue with the Registry and Storage format.
4) The device performs the reset, and the Windows CE setup screens (ie. screen alignment etc.) appear. Continue as per a new install.
>>> METHOD B -> Mtty
1) Kill activesync processes: Ctrl+Shift+Esc in Windows to bring up Task Manager. Kill wcescomm.exe and WCESMgr.exe (by selecting the task on the processes tab, and clicking the End Process button below)
2) Phone needs to be POWER + Record + Pen Reset and on Serial/USB screen. COnnect it to the PC, and it should show USB, with the backlight remaining off.
3a) Run mtty1.42.exe. (or the attached mtty application)
b) Select USB from first list (where COM1 is displayed. Don't press USB button). If USB (or a list item containing USB) isn't in the list, then you have't connected to the PC properly.
(Leave default parameters: 8 bits / Flow Control NONE / Stop bits 1 / Parity None / Local Echo No)
c) Click OK
3) Run following commands:
[press enter first to get USB> prompt]
USB>
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
USB>set 14 0
HTCST ÚÈHTCEUSB>
6. type "task 28" to get your device formatted
USB>task 28
DOC_format_HW+
DOCInfoTableinitHW+
Binary0:dwSize=80000
BINFS0:dwSize=0
FAT0:dwSize=1000000
FAT1:dwSize=2BA0000
All:dwSize=3C20000
USB>
7. type "task 0" to ask your device reboot
USB>task 0
USB>
8) Exit the program, then re-hard-reset (POWER + Record + Pen Reset), leaving on USB screen in order to run ROM Flasher
i will try and answer you soon but i think my problem accured because i'm using windows vista and windos mobile center service SW
Windows CE USB
colhatty said:
I Recentley Tried To Upgrade To The Latest ROM So I Went To The O2 UK Website And Downloaded Xda_IIs_Upgrade_v140242.exe, About Half Way Through The Upgrade My Computer Froze And I Had To Re-Start It.
Now My XDA IIs Wont Turn On And When I Put It In Its Cradle The Power Light Turns Red....Not Orange But Red. I Have Tried Running Xda_IIs_Upgrade_v140242.exe Again But I Just Get;
ERROR 101: CONNECTION ERROR
Is There Anything I Can Do Or Is It Terminal?
Thanks
Click to expand...
Click to collapse
I have the same problem with my O2 XDA IIs, this is how I resolved the problem.
1- Take the battery out
2- Put Battery on while holding onto Power Button and Record
3- Now the PC shoud recognise a Windows CE USB
Now you can updategrade or downgrade.
xplode said:
try mtty method, you may have screwed a lil your device
1. Download mtty from the attachment
2. Stop ActiveSync, by Task Manager (press Ctrl + Shift + Escape) kill two processes rapimgr.exe and wcescomm.exe
3. put your device into the cradle
4. Run mtty (from downloaded) Choose WCEUSBSH001 (or just USB in port) and press OK
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
After this procedure reflash
Click to expand...
Click to collapse
After step 4. mtty alerts with "USB port cant open". What now?
On your phone, when connected, ensure that at the top of the screen, it says "USB", not "Serial". Also ensure you've killed the ActiveSync processes properly.
Also consider:-
* Are you able to use ActiveSync to sync when not following this process?
* Does USB appear in mtty as a connection option?
Ayo said:
After step 4. mtty alerts with "USB port cant open". What now?
Click to expand...
Click to collapse
use this mtty
http://file2upload.com/file/33883/mtty-rar.html
CJBS said:
On your phone, when connected, ensure that at the top of the screen, it says "USB", not "Serial". Also ensure you've killed the ActiveSync processes properly.
Also consider:-
* Are you able to use ActiveSync to sync when not following this process?
* Does USB appear in mtty as a connection option?
Click to expand...
Click to collapse
Done all that... And still "USB port cant open" - I'm using Windows Vista Ultimate... So Might this be a problem for "Mtty"?
(BA_WM5_AKU3.5_R4-xplode.lazy.release(2).rar
Help , I tryed to burn a new rom (BA_WM5_AKU3.5_R4-xplode.lazy.release(2).rar) on my O2 XDA 3. After starting the installation I got a Connection Error and now the screen displays "Serial" and "V2.06". Hard and Softreset does not boot the PDA. What can I do to make the machine working? Can anybody help?
I did all instructions right (Copy ..to Storage Card)
firtst I had an eplus rom.
Installing my next ROM was the latest from the O2 page.
Then I tried AKU3.
you know the rest...
Thany for helping,
Thomas
I found everything I needed. Thanks to all others for the great stuff here.
And it burns burns burns...
CJBS said:
The following methods allow you to get rid of all user data on the device (except for memory recognised by the resident system as being storage cards).
>>> METHOD A -> Device Only (recommended, faster)
1) Use two fingers to simultaneously press the RECORD and CAMERA buttons of the phone (on the phone's left side). Whilst these two buttons are depressed, use the stylus to click the soft-reset button underneath the phone - keep the two buttons depressed until the boot loader screen appears.
2) This should enable three options on the boot screen. These options allows a YES/NO response. Use the RECORD and CAMERA buttons to navigate between the options, and switch the YES/NO values. Set the following:
1] Enable KITL: NO (this is a debug tracing option which isn't required, except possibly for developers)
2] Format Registry Hive: YES (clears the registry)
3] Format Storage: YES (formats the internal memory: "\" directory, and under "\RamDisk\". Items under any storage card "\Storage Card\" are not formatted).
3) Once these options are set, press the MAIL button (in between today and the Pocket IE button) to confirm these options, and continue with the Registry and Storage format.
4) The device performs the reset, and the Windows CE setup screens (ie. screen alignment etc.) appear. Continue as per a new install.
>>> METHOD B -> Mtty
1) Kill activesync processes: Ctrl+Shift+Esc in Windows to bring up Task Manager. Kill wcescomm.exe and WCESMgr.exe (by selecting the task on the processes tab, and clicking the End Process button below)
2) Phone needs to be POWER + Record + Pen Reset and on Serial/USB screen. COnnect it to the PC, and it should show USB, with the backlight remaining off.
3a) Run mtty1.42.exe. (or the attached mtty application)
b) Select USB from first list (where COM1 is displayed. Don't press USB button). If USB (or a list item containing USB) isn't in the list, then you have't connected to the PC properly.
(Leave default parameters: 8 bits / Flow Control NONE / Stop bits 1 / Parity None / Local Echo No)
c) Click OK
3) Run following commands:
[press enter first to get USB> prompt]
USB>
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
USB>set 14 0
HTCST ÚÈHTCEUSB>
6. type "task 28" to get your device formatted
USB>task 28
DOC_format_HW+
DOCInfoTableinitHW+
Binary0:dwSize=80000
BINFS0:dwSize=0
FAT0:dwSize=1000000
FAT1:dwSize=2BA0000
All:dwSize=3C20000
USB>
7. type "task 0" to ask your device reboot
USB>task 0
USB>
8) Exit the program, then re-hard-reset (POWER + Record + Pen Reset), leaving on USB screen in order to run ROM Flasher
Click to expand...
Click to collapse
I am trying your plan B I got the mitty up but I am unable to type into the screen

resetting your zio

Apparently there are a few different methods:
If you can get into the phone:
Dial: ##4357*
Select view
Scroll down to select reset.
6 digit code: 000000
Click Ok
Should reboot.
Dial *228
Click to expand...
Click to collapse
Which is somehow different that simply selecting 'factory reset'.
If you can't get in:
Hard Reset.
Power down the phone
Hold down the volume up, end key, trackball and send key simultaneously.
Phone boots. After it vibrates you let go.
Phone is completely reset as if it came out of the box. You'll need to *228 and reload ALL of your data.
Click to expand...
Click to collapse
The REALLY CRAZY method:
WARNING: This process will clear all user settings and downloaded apps. Data on the SD Memory Card and My Backup will be retained. Prior to following the steps below, ensure the phone is powered off.
Power off the phone.
Press and hold red END key for 2 seconds >> Phone Options >> select Power Off >> Phone will shut down >> Ok​
Remove battery for 15 seconds & replace battery.
Power up the phone.
Press and hold red END key for 2 seconds and wait until the device powers up completely.​
Power off the phone.
Press and hold red END key for 2 seconds >> Phone Options >> select Power Off >> Phone will shut down >> Ok​
Press and continue to hold the Volume Up button using your left thumb.
While still holding the Volume Up key, use your right hand to depress the green Send key, the white Track ball and the red End key (sequential order).
Continue to hold all 4 until keys completely down until the handset vibrates twice then let go of the keys & track ball.
Formatting Data and Cache appears​
If you do not see the above (Formatting Data and Cache) redo steps 1 through 7.
If you get a Fast Boot, Self Test or Blue screen redo steps 1 through 7.
Allow the phone to completely reboot. This may take a few moments.
The phone has now been re-set to factory default settings. Please proceed through standard set up and activation procedures.
NOTE: If you receive a self-test screen or blue screen, the hard reset was done incorrectly. Please try again, from step 1.
Click to expand...
Click to collapse
zio reset
alternately, u can hold volume down, talk, trackball, and end and boot to fastboot. then connect to pc, open command prompt, change directory to where u have your sdk and fastboot, and type these:
fastboot devices (to ensure ur computer sees the device. should see "? fastboot")
fastboot -w (should tell you "erasing userdata....")
afterward, pull battery and reboot
You could do...
"fastboot erase system"
"fastboot reboot"
Then put your phone into Modem Download Mode and run the updater to 2.2
Sent from my from my rooted 2.2 no bloat Zio using XDA App

[Q]LG optimus 4x p-880 IS11LG_systembackup test.signed.apk

I really appreciate any help,
I tried to root my phone, followed the steps here:
http://forum.xda-developers.com/show...45863425638526
I got to step 7., where I wanted to open the app , but all I got was: Unfortunately SystemBackupTest has stopped. How can I fix it ? Knowing that none of lg optimus 4x users faced this problem on most of the internet forums.
A screenshot is attached
the page you included in post is not found!!!
anyways man download this file and follow steps to root!! SAFE i guess u dont need to backup!!
1. Download and install the necessary First you need USB driver for your PC or Laptop to connect your phone. So, grab the LG USB driver and install it on PC.
2.Turn the phone off, press the “volume down” and “power” key to boot, do not release the volume down key until the screen appears with a red triangle robot.
3 Insert the USB connected to the computer, use the “volume” down select “Apply update from ADB, press the power button to determine two lines of yellow text prompts.
4 Double-click ROOT.BAT (PC)
5. Wait until the installation is complete, the phone to return to the menu cursor restart items, press the power button to restart the phone.
6. A Superuser icon appears on the phone, running “information page, click here to check for updates, connect to the network, mandatory update
hope that helps ,,, View attachment 2078934
vieri_202 said:
the page you included in post is not found!!!
anyways man download this file and follow steps to root!! SAFE i guess u dont need to backup!!
1. Download and install the necessary First you need USB driver for your PC or Laptop to connect your phone. So, grab the LG USB driver and install it on PC.
2.Turn the phone off, press the “volume down” and “power” key to boot, do not release the volume down key until the screen appears with a red triangle robot.
3 Insert the USB connected to the computer, use the “volume” down select “Apply update from ADB, press the power button to determine two lines of yellow text prompts.
4 Double-click ROOT.BAT (PC)
5. Wait until the installation is complete, the phone to return to the menu cursor restart items, press the power button to restart the phone.
6. A Superuser icon appears on the phone, running “information page, click here to check for updates, connect to the network, mandatory update
hope that helps ,,, View attachment 2078934
Click to expand...
Click to collapse
The link is :
http://forum.xda-developers.com/showthread.php?t=1818502&nocache=1&z=3345863425638526
nevermind it's ok
vieri_202 said:
the page you included in post is not found!!!
anyways man download this file and follow steps to root!! SAFE i guess u dont need to backup!!
1. Download and install the necessary First you need USB driver for your PC or Laptop to connect your phone. So, grab the LG USB driver and install it on PC.
2.Turn the phone off, press the “volume down” and “power” key to boot, do not release the volume down key until the screen appears with a red triangle robot.
3 Insert the USB connected to the computer, use the “volume” down select “Apply update from ADB, press the power button to determine two lines of yellow text prompts.
4 Double-click ROOT.BAT (PC)
5. Wait until the installation is complete, the phone to return to the menu cursor restart items, press the power button to restart the phone.
6. A Superuser icon appears on the phone, running “information page, click here to check for updates, connect to the network, mandatory update
hope that helps ,,, View attachment 2078934
Click to expand...
Click to collapse
Thanks alot !! :good: :good: :good: I really really appreciate it !! I searched so much on the web before I posted and none was helpful, you should make a post explaining this method and giving it a good tag so it go on the top google search*
I really thankful

need help, installing ota zip to my nexus 6

Hello guys,
i was following this article, from yahoo, i cannot post it
and reached the point of
The fastboot menu will appear and you should see Start in the top right. Press Volume Up till it changes to Recovery. Press the Power button to select it.
You will see an Android with a red exclamation point icon, press and hold the Power key, then press the Volume up key to show the Recovery Menu.
You will get a new menu. Navigate to apply update from adb and select it by pressing the Power button.
but it says this in the cmd
device <null> NOT attached.
the phone is still connected, what do i do now?
please help
hendyanto said:
Hello guys,
i was following this article, from yahoo, i cannot post it
and reached the point of
The fastboot menu will appear and you should see Start in the top right. Press Volume Up till it changes to Recovery. Press the Power button to select it.
You will see an Android with a red exclamation point icon, press and hold the Power key, then press the Volume up key to show the Recovery Menu.
You will get a new menu. Navigate to apply update from adb and select it by pressing the Power button.
but it says this in the cmd
device <null> NOT attached.
the phone is still connected, what do i do now?
please help
Click to expand...
Click to collapse
Where does it say this and at what point? Your phone is 100% stock then, correct? You set up adb correctly?
We'll need more information than supplied. You should walk us through step by step
hendyanto said:
Hello guys,
i was following this article, from yahoo, i cannot post it
and reached the point of
The fastboot menu will appear and you should see Start in the top right. Press Volume Up till it changes to Recovery. Press the Power button to select it.
You will see an Android with a red exclamation point icon, press and hold the Power key, then press the Volume up key to show the Recovery Menu.
You will get a new menu. Navigate to apply update from adb and select it by pressing the Power button.
but it says this in the cmd
device <null> NOT attached.
the phone is still connected, what do i do now?
please help
Click to expand...
Click to collapse
I was having the exact same problem last night, following the same instructions. I still could not figure out how to sideload the OTA, so I ended up just flashing the update and starting from fresh. Wish I had the answer for you.
Here was my thread asking pretty much the same thing: http://forum.xda-developers.com/nexus-6/help/disconnects-computer-entering-bootloader-t3230705
danarama said:
Where does it say this and at what point? Your phone is 100% stock then, correct? You set up adb correctly?
We'll need more information than supplied. You should walk us through step by step
Click to expand...
Click to collapse
100% Stock, yes! 1 week old.
Yes i have set up ADB
I have followed the instruction until this part (i cannot post any link sorry, not authorized by xda)
The following ADB commands are for Windows machines. If you’re using a Mac, just add “./” before each command, for example: “./adb reboot bootloader”.
Assuming you device is already connected to your computer via USB and USB Debugging is enabled, you need to re-start it in fastboot mode. Follow one of the two methods below. Option A may be preferable because it’s another confirmation that your computer recognizes your Nexus device.
A) Type “adb reboot bootloader”
B) Turn your device off, then turn it back on while holding down the relevant key combinations for your device. For many devices it’s Volume Up + Volume Down + Power. You can see what your device’s key combinations are here.
The fastboot menu will appear and you should see Start in the top right. Press Volume Up till it changes to Recovery. Press the Power button to select it.
You will see an Android with a red exclamation point icon, press and hold the Power key, then press the Volume up key to show the Recovery Menu.
You will get a new menu. Navigate to apply update from adb and select it by pressing the Power button.
In the command window — make sure you are in the directory where ADB and Fastboot reside — type: “adb sideload [the full name of the file].zip” without the brackets around the file name.
The update will install and reach 100 percent.
Reboot and enjoy the latest version of Android Marshmallow.
Click to expand...
Click to collapse
(red arrow) and then the cmd says the null error, i am trying this now
I had the same problem. Turned MTP on and then it worked. You're told to turn it off but don't... Its in Settings-Storage-touch the ... Menu top right corner, USB settings and turn ON MTP mode. It worked well for me. I also used the Nexus Root Toolkit - makes things much easier!
Click to expand...
Click to collapse
My phone is able to rebooot (the options comes out sometimes after i did not do anything) and now optimising app (like it usually did after an OTA update)
hendyanto said:
100% Stock, yes! 1 week old.
Yes i have set up ADB
I have followed the instruction until this part (i cannot post any link sorry, not authorized by xda)
(red arrow) and then the cmd says the null error, i am trying this now
My phone is able to rebooot (the options comes out sometimes after i did not do anything) and now optimising app (like it usually did after an OTA update)
Click to expand...
Click to collapse
There are lots of additional steps in that guide and not always the simplest way of doing it.
First thing to do is boot into recovery.
- Turn off the phone.
- Hold volume down + power
- At the bootloader screen, use volume keys to navigate to recovery and press power to select#
- At the Red warning triangle, hold power then press volume up.
At this stage, type "adb devices" in your command prompt and see if it returns your serial number or not. If it does, you can follow the steps to use adb to flash the update.
Please note, the guide talks about USB debugging. This only works in android. Nothing you need to do needs to be done via android so this is nonsense. Also the MTP option only works in android, so setting this in settings as a fix is also nonsense.
danarama said:
There are lots of additional steps in that guide and not always the simplest way of doing it.
First thing to do is boot into recovery.
- Turn off the phone.
- Hold volume down + power
- At the bootloader screen, use volume keys to navigate to recovery and press power to select#
- At the Red warning triangle, hold power then press volume up.
At this stage, type "adb devices" in your command prompt and see if it returns your serial number or not. If it does, you can follow the steps to use adb to flash the update.
Please note, the guide talks about USB debugging. This only works in android. Nothing you need to do needs to be done via android so this is nonsense. Also the MTP option only works in android, so setting this in settings as a fix is also nonsense.
Click to expand...
Click to collapse
I cannot get my windows to detect the phone during recovery mode, it always disconnected at that point.
I'll try again when i have the time, thank you all.
hendyanto said:
I cannot get my windows to detect the phone during recovery mode, it always disconnected at that point.
I'll try again when i have the time, thank you all.
Click to expand...
Click to collapse
Could be a driver issue. You'll need to check device manager. Perhaps uninstall the existing drivers and let it auto detect.
Failing that, install the Naked driver from my adb and fastboot thread (Nexus 6 general > Sticky roll-up thread > Adb and fastboot. What is it?)
I had the same issue with you until i did the following: I used wugfresh's nexus utility. Then I downloaded the respective file from XDA and saved it in the same folder as the Wugfresh's tool. Restarted in Recovery mode and chose 'update from adb'. Connected the phone with the usb having USB debugging on from before going to recovery. Started the CMD window from Wugfresh's tool (Advanced Utilities -> Launch) and check that the phone is connected (I think "adb devices") . Then "adb sideload xxxx.zip" and waited for the process to finish.
Instruction here: androidpolice 2012/11/13/android-4-2-build-jop40c-rolling-out-to-the-nexus-7-now-manual-download-link-available/
You do not have to install the full Android utility. Just use wugfresh;s cmd screen. Good luck!
danarama said:
Could be a driver issue. You'll need to check device manager. Perhaps uninstall the existing drivers and let it auto detect.
Failing that, install the Naked driver from my adb and fastboot thread (Nexus 6 general > Sticky roll-up thread > Adb and fastboot. What is it?)
Click to expand...
Click to collapse
qwerty1gr said:
I had the same issue with you until i did the following: I used wugfresh's nexus utility. Then I downloaded the respective file from XDA and saved it in the same folder as the Wugfresh's tool. Restarted in Recovery mode and chose 'update from adb'. Connected the phone with the usb having USB debugging on from before going to recovery. Started the CMD window from Wugfresh's tool (Advanced Utilities -> Launch) and check that the phone is connected (I think "adb devices") . Then "adb sideload xxxx.zip" and waited for the process to finish.
Instruction here: androidpolice 2012/11/13/android-4-2-build-jop40c-rolling-out-to-the-nexus-7-now-manual-download-link-available/
You do not have to install the full Android utility. Just use wugfresh;s cmd screen. Good luck!
Click to expand...
Click to collapse
Thank you guys! But after this "happy"night, i woke up to the OTA for marshmallow arrived on my phone, so see you guys on the rooting section instead, Thank you thank you for the help

Categories

Resources