Related
Hope you guys can help me out. I disassembled my Cingular 8125 to try and improve the earpiece speaker. I put the device back together and turned it on and it sticks on the boot screen.
When I try to do a hard reset, I get to the point where I have to press send (green button), but then displays the following for a second and then goes back and freezes on the boot loader screen:
format FAT partition
format is complete
I've read some stuff about being able to recover from this using the SD card, but I'm not sure how to do it. If it is possible to recover from SD card, can someone please upload the appropriate files to the ftp site?
Please HELP!!! My ROM versions are below:
IPL: 2.16
SPL: 2.16
GSM: 02.07.10
OS: 2.16.9.1
Thanks!!!
Update:
I'm able to get to the mutli-colored screen by holding the Camera Button prior to starting the Wizard back on. I plug in my USB to my computer, but my computer says "USB Device Not Recognized". How can I get a new ROM on to my device? I tried running the ROMUpdateUtility.exe from a ROM, but it obviously wouldn't work because my computer doesn't see my phone. Please help!!
Thanks!!
Update #2:
When connected to the computer, I got to device manager and see an unknown device under USB. I uninstall the device and do a scan for hardware changes. This finds the phone, but it still shows up as an unknown device. It does say that device is ready to use, but when i try to run the ROM update utility, it still cannot find my phone.
Do I need special USB drivers for the phone to be recognized?
Please guys, any help would be greatly appreciated!
Thanks!!!
you shouldnt need any special driver for your computer to connect to Wizard.
did you install ActiveSync at all ? perhaps its using the driver from that installation....
What OS are you using ?
Yes, I've previously installed ActiveSync 4.1. I am using Windows XP. Would it help to try to uninstall/reinstall ActiveSync? I may give that a try. Will keep you posted. Any other suggestions?
EDIT:
Just tried to uninstall/reinstall ActiveSync and it still says USB device not recognized
it looks like a dead ROM, hope it has nothing to do with the hardware.
Anyway, you try looking through this forum, there are some people who've got stuck on the boot screen, and did a flash (via the bootloader screen, e.g. the multi colour one) on the ROM and seems to fix the problem. Probably you want to put this option last. Mean while, wait for others to repsond, and you may well start looking on how to flash the ROM from bootloader screen.
hanmin said:
it looks like a dead ROM, hope it has nothing to do with the hardware.
Anyway, you try looking through this forum, there are some people who've got stuck on the boot screen, and did a flash (via the bootloader screen, e.g. the multi colour one) on the ROM and seems to fix the problem. Probably you want to put this option last. Mean while, wait for others to repsond, and you may well start looking on how to flash the ROM from bootloader screen.
Click to expand...
Click to collapse
Thanks for responding. I'm ok with having to reflash, but the problem is that my computer doesn't seem to recognize my device when i'm at the multi color screen.
Isn't there a backup battery in these devices? I had my Wizard disassembled for 4 hours. I guess the backup battery could have died during this span, but even if it did, what implications would that have?
You still have hope
Get it to the bootloader screen. Connect via USB to your PC (make sure you have active sycn installed) and run an RUU to replace your ROM. I had to do this after trying to downgrade to the original Cingular ROM on my 8125. Scared the S*!T out of me when it hung on the Splash screen and wouldn't load. I thought it was toast but using the Bootloader and an RUU it put it back to normal again.
It won't look like the PC is recognizing the device but it will as long as its in Bootloader.
Let us know if you get it fixed.
Re: You still have hope
hellomoto_25 said:
Get it to the bootloader screen. Connect via USB to your PC (make sure you have active sycn installed) and run an RUU to replace your ROM. I had to do this after trying to downgrade to the original Cingular ROM on my 8125. Scared the S*!T out of me when it hung on the Splash screen and wouldn't load. I thought it was toast but using the Bootloader and an RUU it put it back to normal again.
It won't look like the PC is recognizing the device but it will as long as its in Bootloader.
Let us know if you get it fixed.
Click to expand...
Click to collapse
Thanks for the reply. The problem is that when I plug the device into my computer, I get a USB device not recognized error. I try to proceed with ROMUpdateUtility.exe anyways, and get this error:
"The update utility cannot connect to your PDA phone..."
Seems like updating via USB is not going to work for me. Can I write a backup to the SD card from the PC, put the SD card in the phone, and then boot from there? I've read some posts along these lines, but detailed steps would be very helpful. THANKS!!!
You need an SD card dump image.
This is NOT a file in the sense of a file on the SD card. Its a RAW image. You need someone who has dumped their firmware in that fashion to send you the SD image.
You then write it onto the SD card using something like "psdwrite" (which will, by the way, DESTROY the filesystem on the SD card - don't have anything on there you care about!) and then insert it into the phone with the power off. Hold the CAMERA button and turn it on; when it asks if you want to restore the image, hit VOICE.
Note that for 1.x IPLs/SPLs the backlight will be OFF during this procedure, so you have to pay attention and/or have a good flashlight handy.
Genesis3 said:
You need an SD card dump image.
This is NOT a file in the sense of a file on the SD card. Its a RAW image. You need someone who has dumped their firmware in that fashion to send you the SD image.
You then write it onto the SD card using something like "psdwrite" (which will, by the way, DESTROY the filesystem on the SD card - don't have anything on there you care about!) and then insert it into the phone with the power off. Hold the CAMERA button and turn it on; when it asks if you want to restore the image, hit VOICE.
Note that for 1.x IPLs/SPLs the backlight will be OFF during this procedure, so you have to pay attention and/or have a good flashlight handy.
Click to expand...
Click to collapse
Genesis3,
Thanks for your wonderful insight. I really appreciate your help.
Now can someone help me with getting an SD image? What constitutes an image file? Is it simply the .nbf file? Do I just use psdwrite and copy the nbf file onto the card? Is there something on the FTP site I can use? My configuration as mentioned in the original post is:
IPL: 2.16
SPL: 2.16
GSM: 02.07.10
OS: 2.16.9.1
I had a similar problem and reflashing the rom using the usb is possible. Don't use a flasing utility, though.
Find a self contained rom upgrade from the FTP. As long as you see USB on the bottom left side of your screen, it should work. After that, reflash with whatever rom you want. Hope it works. Nothing worse than an the feeling you have holding an expensive paper waight.
wireless_one said:
I had a similar problem and reflashing the rom using the usb is possible. Don't use a flasing utility, though.
Find a self contained rom upgrade from the FTP. As long as you see USB on the bottom left side of your screen, it should work. After that, reflash with whatever rom you want. Hope it works. Nothing worse than an the feeling you have holding an expensive paper waight.
Click to expand...
Click to collapse
Thanks for the reply. I'm not sure what you mean by "self contained rom". In the past, I've used K-JAM_WWE_216901_2169101_020710_ship.zip from the FTP site, and ran the ROMUpdateUtility.exe without any problem. Now, since I cannot make a connection to the computer via USB, I am unable to run ROMUpdateUtility.exe. Is there an alternative "self contained" file I can use that will work in spite of the unknown USB device message?
Thanks in advance...
try to DL this file: RUU_Prodigy_1060701_101_11310_QTEK_WWE_Ship.exe. Its on the FTP. Follow this link:
http://wiki.xda-developers.com/index.php?pagename=BA_FTP_Site
click on the FTP Root link, navigate here:
ftp://ftp.xda-developers.com/Wizard/Roms/Qtek/ and download the file. Put the phone in bootloader, attach to PC (make sure the phone has USB shown in the bottom left corner, and run the file.
Ignore any references to ActiveSync or any connections period. Just run it all the way through the installation process. When all is done, you can upgrade, down grade, etc using the appropriate method (I use aWizard) Let me know if this helps.
Wireless One
wireless_one said:
try to DL this file: RUU_Prodigy_1060701_101_11310_QTEK_WWE_Ship.exe. Its on the FTP. Follow this link:
http://wiki.xda-developers.com/index.php?pagename=BA_FTP_Site
click on the FTP Root link, navigate here:
ftp://ftp.xda-developers.com/Wizard/Roms/Qtek/ and download the file. Put the phone in bootloader, attach to PC (make sure the phone has USB shown in the bottom left corner, and run the file.
Ignore any references to ActiveSync or any connections period. Just run it all the way through the installation process. When all is done, you can upgrade, down grade, etc using the appropriate method (I use aWizard) Let me know if this helps.
Wireless One
Click to expand...
Click to collapse
Thanks for your reply. I've tried the course of action that you've suggested, but i cannot get through the installation process because of inadequate connectivity between the phone and my PC. I see the USB in the bottom left hand corner, plug into the PC, and immediately see a USB Unknown device error. I ignore that and try to run the ROM anyways and it fails and I get an Update Error:
"The Update Utility cannot connect to your PDA Phone. Please check that your USB/cradle is connected..."
That's why I think I got to go the SD card route, so anyone with an image file that i can put on my SD card, I really could use the help!
It is NOT a NBF file.
The problem with the 8125 is that if you are somehow not CID unlocked the wrong SD image will actually hurt you more than it helps.
You need to find someone with a Cingular 8125 SD image - I have one for the T-Mobile MDA but not for the Cingular "as-shipped" ROM.
Genesis3 said:
It is NOT a NBF file.
The problem with the 8125 is that if you are somehow not CID unlocked the wrong SD image will actually hurt you more than it helps.
You need to find someone with a Cingular 8125 SD image - I have one for the T-Mobile MDA but not for the Cingular "as-shipped" ROM.
Click to expand...
Click to collapse
Genesis3,
Thanks for confirming it's not a NBF file. I had previously CID unlocked using awizard and then installed a newer IMATE ROM:
IPL: 2.16
SPL: 2.16
GSM: 02.07.10
OS: 2.16.9.1
I did not install the IMATE Extended ROM or Cingular customizations after upgrading to the IMATE ROM. Do I still need a Cingular 8125 SD image, since i've already upgraded my ROM, or do I now need an IMATE SD image to match my current configuration? Or does the type of image file really not matter?
Thanks in advance!
I really hate to beg, but I am desparately seeking an SD image file backup. I'm going out of town in a couple of days, and would love to have a working wizard for my trip.
Can any one of you kind souls please upload your SD image file backup to the FTP site? It really is my last ditch effort before having to send the phone back.
I truly appreciate all the help and all the responses I have received to date.
THANKS!!!
sunil23 said:
I really hate to beg, but I am desparately seeking an SD image file backup. I'm going out of town in a couple of days, and would love to have a working wizard for my trip.
Can any one of you kind souls please upload your SD image file backup to the FTP site? It really is my last ditch effort before having to send the phone back.
I truly appreciate all the help and all the responses I have received to date.
THANKS!!!
Click to expand...
Click to collapse
Sunil,
i apologize for not responding your PM sooner but wasnt available due to travel plans.
I am trying to upload the files to the Upload folder now and i iwll let you know when i am done.
Thanks
getting permission denied when i tried to upload the documents.
is there another password i should be using besides xda/xda ?
HELP ME OUT GUYS, IM TRYING TO FLASH THE WM6 ROM TO A CINGULAR 8125: IPL 2.25, SPL 2.25 AND SEEM TO BE STUCK IN BOOTLOADER MODE. I FIRST GOT AN UPDATE ERROR AT 99%, PERFORMED RECOVERY - AND GOT THE SAME ERROR AGAIN. NOW THE RUU WON'T EVEN START AND I GET ERROR 264 : CONNECTION ERROR. ACTIVE SYNC NO LONGER IS GREEN, ETC. I DOWNLOADED THE XDA MOBILE 6r2a.zip FROM THIS SITE. NOT SURE WHAT I DID WRONG. I THINK I NEED TO GET BACK TO AN ORIGINAL ROM AND START ALL OVER BUT NOT SURE WHERE I CAN FIND ONE. THANKS.
ditto
ensophalic said:
HELP ME OUT GUYS, IM TRYING TO FLASH THE WM6 ROM TO A CINGULAR 8125: IPL 2.25, SPL 2.25 AND SEEM TO BE STUCK IN BOOTLOADER MODE. I FIRST GOT AN UPDATE ERROR AT 99%, PERFORMED RECOVERY - AND GOT THE SAME ERROR AGAIN. NOW THE RUU WON'T EVEN START AND I GET ERROR 264 : CONNECTION ERROR. ACTIVE SYNC NO LONGER IS GREEN, ETC. I DOWNLOADED THE XDA MOBILE 6r2a.zip FROM THIS SITE. NOT SURE WHAT I DID WRONG. I THINK I NEED TO GET BACK TO AN ORIGINAL ROM AND START ALL OVER BUT NOT SURE WHERE I CAN FIND ONE. THANKS.
Click to expand...
Click to collapse
That was the same rom that toasted my Qtek 9100 and now I'm stuck at the 99% mark before I get update:[302] error. Sorry didn't mean to steal your thread m8 but when I aksed the forum if they could help me out I got zero response ...so mines a brick right now.
BTW: I've tried the Wizard Love ROM but that was spanish I think and comes up with "INVALIDO" or something similar. I've fully charged the battery, removed the SD card and disabled "allow USB connections" in activesync, along with killing off wcescomm.exe ...but still no joy. Hope you get sorted with yours soon.
Original ROM's are easy to find, just go to either your phone service providers website and it should be on there, or go to HTC's website and they'll either have it or have links to where you can get it. Before you tried flashing XM6r2a, did you CID unlock your phone? That may be your problem.
ADD+, your phones not a brick yet if you can get in to the bootloader, which since you said that you tried to flash the wizard love ROM I'm guessing you can still do. You should also re-flash the original ROM that was on there and see if you can at least get that one to load back on there.
Also, for Original ROM links try this link - http://wiki.xda-developers.com/index.php?pagename=Wizard_Upgrades
xeno1 said:
Original ROM's are easy to find, just go to either your phone service providers website and it should be on there, or go to HTC's website and they'll either have it or have links to where you can get it. Before you tried flashing XM6r2a, did you CID unlock your phone? That may be your problem.
ADD+, your phones not a brick yet if you can get in to the bootloader, which since you said that you tried to flash the wizard love ROM I'm guessing you can still do. You should also re-flash the original ROM that was on there and see if you can at least get that one to load back on there.
Also, for Original ROM links try this link - http://wiki.xda-developers.com/index.php?pagename=Wizard_Upgrades
Click to expand...
Click to collapse
Got mine fixed by using the Xda_MiniS_LaunchROM_v154102.exe from the link in the definitive guide sticky. So as they say RTFM!!
Hello,
I've tried to update my phone using the shelltool method and my phone crashed during the update.
Now it can't boot. it's freezed on the splash screen.
I've tried to put the CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE rom and it does nothing.
I have a G3 device, the IPL/SPL is now 1.01
Thanks in advance for your help
Flash back to official carrier ROM.
I have already tried using the bootloader method. it tells me that the device is not compatible
Try it doing the storage card method.
I also tried and it tells me I don't have the right
Before the first update, I have made a backup of the OS ROM but the file format is NBA. Is there a solution to reuse my original ROM?
In Addition to the SD method, the bootloader is password protected
Try reflashing the ROM you were flashing in the first post using the RUU in bootloader mode. You shouldn't need to use the shelltool to flash that one. Then when you get that flashed on there do your CID unlock. After that you should be able to flash any ROM you want.
I've tried tu put Button's ROM using the RUU in bootloader mode and its still blocked
Try flashing the wizard love rom then. I'm not sure where it is at the moment, but you can find it on here somewhere.
I also tried this ROM
I have made some research.
At the beginning (when my first upgrade crashed) someone on a chat told me to do a doctest.
No the problem is that the memory is damaged.
When I try a hard reset, I have the message "format is failed"
Any idea?
You've got me on this one, I don't think I've run across anyone else ever having this problem. By the way, did you remove any miniSD card that you had in the phone before flashing? Having one in there while flashing tends to cause people problems.
Also, I just realized that you said that you used sheeltool to flash the first time when you flashed the button rom and that it changed your IPL/SPL to 1.01. Flashing using shelltool won't change your IPL/SPL, it skips those files if they are added to a rom since they are the files that will destroy a G4 device. So, if it did change them then that's where you did something wrong. Why don't you start over and explain exactly what you did on the first flash with the button rom and see if we can't figure it out from there.
OK I'll explain from the beginning
Before beginning the flash, I have made a backup of the ROMs (OS, Radio and Ext) with aWizard.
I wanted to put a french WM6 ROM. In the the tuto, it was told to use shelltool to do this. For an unknown reason, the phone crashed. So I had to reboot the phone because it was freezed and after this point it did'nt boot.
I went on a chat to get help and someone told me to start the bootloader and with mtty enter the command doctest (I think he's a joker becose today I saw this command is very dangerous).
When I saw this command doesn't work I discovered this forum and tried 2 of the 3 methods to unbrick a phone in the wiki.
I can't use the SD one because the boot loader is password protected.
I also discovered today that the IMEI number doesn't correspond to the label on the phone.
Here is my story .
http://forum.xda-developers.com/showthread.php?t=276963&page=7&highlight=wizard+bootloader+password
This post seems to have helped many. Read from beginning to end, then try to follow it. Good Luck.
raskell said:
http://forum.xda-developers.com/showthread.php?t=276963&page=7&highlight=wizard+bootloader+password
This post seems to have helped many. Read from beginning to end, then try to follow it. Good Luck.
Click to expand...
Click to collapse
I'can't use imei check because my imei is invalid
Why do you think your IMEI is invalid? If the only reason is that it shows a different one on the box than it shows in aWizard or whatever program you're using, don't worry about it because that seems to happen quite a bit. Usually it's because it got put in the wrong box. Anyway, you're in luck, I have a program that I believe I downloaded off of XDA which is a version of the IMEI-checks unlocker with the master unlocker code for all wizards.
Well, I was going to upload that tool for you but after trying 6 times to upload it and it failing each time I figured that maybe I should wait a little bit and try again later.
I think the IMEI is different because the one given from imei-checks is different from the one on the label back the battery.
Also, when I tried to order an UNL file with the IMEI given by the unlocker, they told me its a wrong number
Lets try this again.
Still failing to upload. I'm not sure why, but I'll try yet again later.
I sent you in PM the address of my ftp server
I forgot to put the DIAMING.nbh file on my diamond! now it just shows up with "Touch Diamond" and then resets! i need help please
is this an easy fix??
Thank you so much!
go to bootloader (vol down + reset) and flash new rom from romupdater in windows
i got to bootloader but it won't read my usb... there is no DIAMING.nhb file (or whatever it is called) on my phone.. is there any application that will let me get the usb to work.. any ideas???
thank you
i can still run the custom RUU, and it runs on my phone as well.. so is there anyway.. or is there already one out there that has the DIAMIMG.nbh with it so that it installs without the need to manually move the file to the phone..
thanks again
Yes it does, if u get into bootloader, connect your phone to PC, you should see written USB in bootloader a then run RUU from windows, it should work. I experienced similar problem and that was my solution
i tried to flash a different rom onto my diamond, and it got 100% done.. but still... i wasn't able to move the DIAMIMG.nbh file to my root... do i need to use a rom that doesn't have a DIAMIMG.nbh file? where would i find one.. if i may ask?
your help is appreciated thank you
UPDATE
ok... so i found, and downloaded 2 RUU roms. one of them got to 90% done, and the other got to 91% done... does anyone know why this is..? these are the official roms, (I think).
i have searched for the past 2 days almost nonstop, i need a rom that will fully install onto my phone. This rom can't have me move the DIAMIMG.nbh file over manually either, because i cannot do this in bootloader mode.
i tried these 2 official roms. _HTC Touch Diamond_QMR_RUU_Diamond_HTC_Europe_1.93.401.2_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship.exe
and this one,
RUU_Diamond_HTC_Europe_1.35.401.3_Radio_Signed_Diamond_52.26.25.09_0.93.25.26_Ship.exe
do you know where i could download some other roms at? thanks
did you use Hard-SPL? maybe something with spl theres wrong
When flashing from your PC, you don't move an NBH over.
Go to htc.com, support, and download the current rom for your phone.
Soft reset holding volume down
Connect to your PC (DIRECTLY and NOT through a hub)
Run the updater you just downloaded from HTC
ya. i'm using hard-spl..
i tried getting a rom from htc, but i don't think that it's recognizing my s/n.. could i borrow someone elses??
i'm connecting my phone to a USB that's located in the back of my computer... i don't think it's a hub, but i'll try a different port maybe..
thank you again
so here's the full story.
i tried to install a rom.. it was shaks v3. and this was the rom. -> 2.03.401.2
i didn't put the diamimg.nbh file on it before i flashed it.
the RUU ran fine, but afterwards it was stuck just saying "touch diamond" , and it was resetting itself constantly.
i got into bootloader mode, and noticed that i could not transfer files from my computer to phone through that..
so i downloaded a rom that didn't require you to move the .nbh file over manually. it got to 90% , and then stopped i tried another, and it got to 91% and stopped, i tried another, it got to 89% and stopped, and i tried one more that got to 19% and stopped. i have tried using these RUU's on different computer's to install also..
IS there any way to move files using the bootloader mode? i know that the computer recognizes it, but not as a device with removable storage..
I'm starting to lose hope with my phone, and any help will be greatly appreciated
i don't know if it makes a difference, but i got my phone from Sprint.
ok!!! i totally just remembered that roms were made for CDMA users (Sprint verizon vodafone... ME) and GSM users... i was trying to flash a GSM rom onto my phone...
make sure that you know what type of rom to flash.. there are CDMA roms out there.. you just have to search...
thank you Felipe404, for your quick replies, and you made this easier for me.
thanks to JonInAtl for the precise reply...
both of your guy's help made a huge difference, that you don't even know.
WHOA!!!!!!
yea, i did the same thing,.. flashed my gsm diamond with cdma rom, after flash it just showed the bootscreen - Touch Diamond and there it stopped... so i got to the bootloader, connected the device to pc and flashed another rom from computer.. and it did work
no problem mayne
Just to clarify here, the ONLY reason to copy DIAMIMG.nbh to your device is if you do not want to update with the RUU. You can install every ROM using the RUU regardless of who made it.
That said, every time I want to update, I do have to copy it over to my phone as the USB port on it no longer works (it still charges, just says unknown device regardless of the ROM).
(Rogers HTC Dream)
Ok, so, i know this sounds ridiculous, and you may find yourself asking "WTF Was He Thinking?!?!?" But, was a late night, and i was quite possibly half asleep lol...
Ok, so, long story short, i have tried possibly every rom for the Rogers Dream, and majority of them didn't work for me, or atleast, if they did, not that well.... Cyanogenmod 6 worked ok, although it started to get slow pretty fast :/ Anyways, i had previously rooted and flashed my dream with the steps provided on cyanogen's wiki, but i had never updated the kernel or anything, so, i came to the conclusion that it was possibly my kernel that was un-allowing me to run most roms, so i decided to update my kernel using the steps here
"http://forum.xda-developers.com/showthread.php?t=831139"
Everything went well, kernel updated, wiped everything, except i accidently deleted my recovery.....but thought, no problem, i'll just follow the instructions on the thread, no biggie.....it said to download the "orange-1.58.73.2.nbh" and flash that......BUT... I Should have known that the Orange one was the one for T-Mobile!! But out of stupidity i didn't realize it and flashed it!! Now my phone won't boot up or Anything :/ when i try to boot into recovery OR Hboot, it shows the t-mobile startup flash, then shows an error with a triangle and a yellow exclamation in the middle, with a phone on it's side beside it!! :S
Did i completely mess up my phone?.... Someone please help!! x.x
I got a Rogers dream and I just push amonRA with adb. As for the exclamation screen, I think there is a key combo to bypass it. Something like volume up and power at the same time. I can't remember now the exact combination. Took a lot of Googling to find it, and if I remember correctly the dream has a different combo than the tmo did. But with this nexus one my memory has faded.
Sent from my Nexus One using Tapatalk
The orange nbh is orange not t-mob..
But has a eng spl so recovery is easy.. head over to my 2708+ radio thread and flash that, a 2708+ rom (most new roms support it and older ones the kernel in that thread will fix it.
Rogers if they are your carrier may cut wireless data there is a e911 wavier form to get around this search for it or ask the support person if they cut your data for detasils.
The good thing about using the 2708+ radio/kernel is extra ram, and it works on the rogers dream the same way as the non rogers dream thus you can ask more people to help support you with 2708+
Thanks for the reply guys,
ezterry:
thanks for replying, would had posted in your thread but didn't want to jam it full of even more posts of someone needing help lol...
as for your reply, it was after i had flashed the orange nbh that i was getting the t-mobile splash :S thus i assumed it was t-mobile.... but, as for flashing anything, i can't....when i try to boot phone in hboot or recovery, i get the error i previously mentioned, and when i normal boot, i can only get to the screen that says to plz insert sim card, and it won't let me pass that screen :S....that's where im stuck.....i tried using the usb cord to access adb through it, but on the comp it says there are no adb devices, i'm assuming it's because i can't get past the "no sim card" screen to enable debugging ..... Any suggestions?
Thanks!!
I'm going to hope you are doing something silly since your description indicates no problem with the phone.
SpawnOfSatan said:
but, as for flashing anything, i can't....when i try to boot phone in hboot or recovery, i get the error i previously mentioned
Click to expand...
Click to collapse
That /!\ screen *is* recovery, alt+L will show you additional options.. but in its self its not that useful.
SpawnOfSatan said:
, and when i normal boot, i can only get to the screen that says to plz insert sim card, and it won't let me pass that screen :S....that's where im stuck..
Click to expand...
Click to collapse
I don't recall if adb is enabled by default on the orange rom; regardless this is the rom. (putting a sim card active or not in the phone may let you get further however ought not be necessary )
So either you got so anoyed at your phone you did phisical damage to it or you are attempting to enter HBOOT/Fastboot incorrectly.
Powering on when holding 'camera' is supposed to always bring you to the HBOOT screen; then pressing send or back as prompted will let you to the Fastboot screen (don't re-flash the orange NBH, say no if it asks)
Alternatively either booting with send or back will go directly to HBOOT.. (The rogers [2000 series] dream uses Send while the t-mobile (100 series) users Back but some SPL only provide the back options regardless of dream model.. I don't recall about 1.42.2000 so you will want to try both)
In theory Home is the only button to send you to recovery.
Once in fastboot it ought to be a full featured fastboot and the normal 2708+ install instructions will work using fastboot on your PC
That /!\ screen *is* recovery, alt+L will show you additional options.. but in its self its not that useful.
Click to expand...
Click to collapse
Ahh ok lol, i'd installed RA recovery when i first got the phone, so it was the only recovery screen i remembered ever seeing, thus why i was confused, but yah, hit alt+L and saw the options, but yah, not that many :/
So either you got so anoyed at your phone you did phisical damage to it or you are attempting to enter HBOOT/Fastboot incorrectly.
Click to expand...
Click to collapse
Apparently was entering it wrong, i was used to using Home+Cam+End to enter hboot.....so that's my fault....
Once in fastboot it ought to be a full featured fastboot and the normal 2708+ install instructions will work using fastboot on your PC
Click to expand...
Click to collapse
[/QUOTE]
When i enter hboot, it looks like a friggin rainbow now lol....red, green, blue, and white bars as the background :/ and once in hboot, it says "Serial0" in the middle of the screen :S and when i plug it into the computer, i tried hitting both back, and send, and it makes the "Serial0" dissapear, but seems no matter what i do, it won't show the phone as a connected device in fastboot :S
Thanks again for replying soo quickly and all the help u've been giving me, any advice on where to go from here or getting it to enter fastboot?
What you are describing is not 1.42.2000.. but 0.95.0000.. or that its likely the Dreaimg you flashed was the t-mobile rc29 and not the orange nbh..
Rc29 can be flaky.. but there are two options
1) go to recovery, alt+l and wipe, put a sim card into the phone and root via telnet.. assuming you have the 1.x radio of rc29 follow the link to my 1.33.2003 spl then with that install 2708+ normally
2) if you still can't boot you will need to use/make a goldcard (if you don't already have one this may require finding a friend's phone to help make one) and this time flash the orange nbh *not* rc29
0.95.0000 will not let you flash a rogers nbh so there is no way to re-flash with out a goldcard.. otherwise I'd just have you flash the roger 911 patch and re-root from there..
hey if you are still getting that screen with the yellow triangle and '!' that means you have stock tmobile recovery with no rom lol can you try to press (alt+L) hold alt and press L should make a list pop up.. if it does than maybe you can still re root it so than it will read your sim... but im not sure if the rogers G1 has and different software so it could possibly make it worse.. lol just a suggestion
ezterry said:
What you are describing is not 1.42.2000.. but 0.95.0000.. or that its likely the Dreaimg you flashed was the t-mobile rc29 and not the orange nbh..
Rc29 can be flaky.. but there are two options
1) go to recovery, alt+l and wipe, put a sim card into the phone and root via telnet.. assuming you have the 1.x radio of rc29 follow the link to my 1.33.2003 spl then with that install 2708+ normally
2) if you still can't boot you will need to use/make a goldcard (if you don't already have one this may require finding a friend's phone to help make one) and this time flash the orange nbh *not* rc29
0.95.0000 will not let you flash a rogers nbh so there is no way to re-flash with out a goldcard.. otherwise I'd just have you flash the roger 911 patch and re-root from there..
Click to expand...
Click to collapse
Hboot is 0.95.0000
Radio is 2.22.19.26I
So i'm guessing it is the rc29 And i'm not too sure what a gold card is? :S
SpawnOfSatan said:
Hboot is 0.95.0000
Radio is 2.22.19.26I
So i'm guessing it is the rc29 And i'm not too sure what a gold card is? :S
Click to expand...
Click to collapse
that sounds like stock 1.5 firmware to me
..Still have yet to find a solution....any help please?
info again is
HBOOT-0.95.0000
CPLD-4
RADIO-2.22.19.26I
Background:
Accidently wiped rogers rom + flashed t-mobile rom, and since then,
Hboot says "Serial 0" and won't allow me to flash any images, phone doesnt have a recovery, will boot up now, but only to the android set-up process which i can't continue with because it won't accept my rogers sim card, despite the fact i unlocked the phone before all this happened :/ so i can't sign in to or create a google account. Have attempted every bypass to get past it with no success. Obviously since i can't get past it i have no access to adb...
Please help
Just out of my curiousity, got download the orange nbh file (make sure that it marked orange).
Format your SD card to FAT and put the nbh file in the root of your SD card.
put the SD card in your G1.
Boot up with camera+power and flash it.
See if that work.
BeenAndroidized said:
Just out of my curiousity, got download the orange nbh file (make sure that it marked orange).
Format your SD card to FAT and put the nbh file in the root of your SD card.
put the SD card in your G1.
Boot up with camera+power and flash it.
See if that work.
Click to expand...
Click to collapse
Thank you for your response, unfortunately i have tried that countless times with no luck it says it cannot read or flash or something, i forget what it says Exactly but it wouldn't allow it x.x any other suggestions?
I'm Really desperate x.x and i have been having the crappiest luck lately. I bought a phone off kijiji today, spent 3 hours trying to meet up with the guy to buy it, then when i did get it (after all the running around) i took it to "The Source" to get it activated in my name , and after 4 hours (5pm-9pm) they finally said they tried everything but couldn't do it because the phone is registered to someone with a contract that has a suspended account do to owing an outstanding amount of money!!
At this point, when you boot up the phone. What do you see?
BeenAndroidized said:
At this point, when you boot up the phone. What do you see?
Click to expand...
Click to collapse
It loads up to the setup screen, in which i cannot bypass...i have tried with another active (with data) rogers sim, telus sim, and virgin mobile sim card, but none of them will work....and like i previously mentioned, i unlocked the phone prior to all this happening :S
OK! I am not sure why it will not let you activate your phone. But don't worry about that ATM.
Let try activate your G1 over wifi. Follow the instruction from the link below.
http://theunlockr.com/2010/01/10/how-to-activate-the-g1-without-a-data-plan-or-sim-card/