[REF] The DEFINITIVE MTTY Thread!! - Xperia Edition - XPERIA X1 ROM Development

Since people are starting to have problems with their SEX1, I think its gonna be usefull to have this thread as a reference for fixing bad flashs and corrupted memory.
The method to connect with MTTY are the same for all phones so please refer to this thread to PREPARE your computer :
HTML:
http://forum.xda-developers.com/showthread.php?t=540290
However, the commands for the xperia are slightly different.
Once your in MTTY and Connected :
Press enter first to get prompt (Will Show as CMD)
---------------------
MTTY OUTPUT:
---------------------
CMD>
---------------------
type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
---------------------
MTTY OUTPUT:
---------------------
CMD>set 14 0
HTCST ÚÈHTCEUSB>
---------------------
type "task 28 55aa" to get your device formatted:
---------------------
MTTY OUTPUT:
---------------------
Cmd>task 29
Format BINFS start
Fill RSVD information for block 288 to 321 YOU WONT SEE THIS LINE IF YOU JUST TYPED TASK 28. YOU MUST TYPE TASK 28 55aa OR IT WONT ERASE EVERYTHING.
CE start sector=0x14, total sector of CE and TFAT=0x14
CE start start block=321, total block=1727
ERASE block 1337 FAIL !!!
Write 0xFF start page=0x5040, total page=0x1AFC0
Format BINFS end This part is just copied from the diamond thread so it might be a lil different with xperia. The important thing is to see the FILL RSVD line.
Cmd>
---------------------
type "task 8" to ask your device reboot:
---------------------
MTTY OUTPUT:
---------------------
Cmd>task 8
Cmd>
---------------------
Immediately DISCONNECT your phone
et voila!
If somebody know how to extract info's from the xperia bootloader, maybe we can know what other tasks could be usefull.
I think this should work for most people.

maybe you can also provide working mtty software and usb driver? thanks for the thread.

This should be sticky!
Thanks for writing the info, it is very good.

The working drivers are in the thread that is linked to in the first post!
http://forum.xda-developers.com/showthread.php?t=540290

You MUST flash a Stock ROM after this process! (i think, flashing a custom ROM failed for me)

help!! to bootloader mode
when im trying to enter bootloader mode it detects kovsimg.nbh(any rom that has been copied to root of the card) ...it asks "Press power button to start update image"
how can i stay at tricolor mode to run mtty? shouldn't i copy kovsimg.nbh to root of the card? help

remove your card
done

Jonny4911 said:
You MUST flash a Stock ROM after this process! (i think, flashing a custom ROM failed for me)
Click to expand...
Click to collapse
You don't have to flash a stock rom.
Flashing a custom rom will also work. It will just format your phone and after that rewrite the flash so doesn't matter if it's a stock or custom rom

Jonny4911 said:
remove your card
done
Click to expand...
Click to collapse
thank you..did it..successful

i can see fill rsvd after type 2855aa
i can see nothing after type task 29
and the system still exists after mtty
what problem ?

simpleguy said:
i can see fill rsvd after type 2855aa
i can see nothing after type task 29
and the system still exists after mtty
what problem ?
Click to expand...
Click to collapse
There is no problem.
The system will reinstall itself but any remaining information ( bad sectors ) from previous flash will be remove.
Your rom wont have any problems.
NOTE : Task 29 is NOT for XPERIA

after disconnect ????
all run ok with me
but what i should do after disconnect my phone, how can i do these step
((7: Immediately DISCONNECT your device and hold "Vol Down and Back" (Back = Small Arrow above "End Call" Button) to Initiate ROM Flash
8: After ROM flash Hard-reset (Pen Reset, then Press and Hold Vol Down and Circle) again, on completion "Press Vol Up To Boot" Is displayed, press "Vol Up" and allow the ROM to boot.))

thank you 8)

Related

750 Dead after flashing with wrong OS

Hi everyone,
I have a big problem and I need urgent help please. I have ATT 750 unlocked and I'm outside the States now. My Treo was 6.0 then I upgrade it to 6.1 so far so good.
Then I saw a custom rom that I thought it was interesting. the custom rom was for HTC Dimond I think. without paying too much attention. I started the upgrade. It went 70% before the upgrade crashed.
Now my Treo is not responding to anything. I have the original ATT 6.0 SD upgrade and I have the 6.1 lite upgrade. I'm using CheetahUnlocker to flash the SPL (that is working) but when I try to install the 6.0 or 6.1 using Kaiser Custom RUU v1 it crash.
I saw an earlier post that suggest to place the original 6.0 on a freshly formatted SD and install from there. that is not working either. when I try to install the software it goes into these steps before it crashes: btw, I have the tri-color bar and it has the following info:
CHEE100
IPL-0.20
SPL-1.40.01iNex
while update in progress i see the following:
CHEEIMG.nbh
SPLASH1 - OK
BOOTLOADER - OK
GSM - OK
MicroP - OK
EXTROM - Fail
OS -
After the crash I get this msg: "Update Terminate Update Failed"
Any suggestion please? need more info? then let me know
Thanks in advance
Sam
Someone please help.... I'm sure someone has some suggestions.
By the way, I've tried RUUwrapper and that didn't help either.
Thanks in advance
I've got the same problem and finally I can solve my problem.
The procedure :
1. Open mtty and by connection via usb, just do :
Command mtty:
- task 2a
- flash:
[1- press enter
2 - type "set 14 0"
3 - type "task 28 55aa"]
you shoul see now the program runing a lot of things that I don`t remember what...
then when it ends try the SD instal...
If It still doesn`t work then:
[1- press enter
2- "erase"
3- "checksum"
4- "checkimage"
5- "task 0"]
then reflash your radio & OS by SDCARD...
- set 16 0 0
- info 7
- info 8
2. It means your PDA has no ROM OS and Radio.
3. Copy CHEEIMG.nbh (ROM OS) to formatted SD Card.
4. Insert the SD Card to PDA and just install by push the 3rd side button together with soft reset (by stylus).
5. Replace file CHEEIMG.nbh (ROM OS) with CHEEIMG.nbh of Radio.
6. Do same procedure as number 4.

new rom dont update

i think , i was do something my Xperia
now i dont update new release ROM 3A
what i must do?
boot screen wrote
KOVS110
SPL-0.72.0liNex
MicroP1-787
MicroP2-707
srry my bad english
HELP MEEEE plss.
thnx for all help
ufkozcan said:
i think , i was do something my Xperia
now i dont update new release ROM 3A
what i must do?
boot screen wrote
KOVS110
SPL-0.72.0liNex
MicroP1-787
MicroP2-707
srry my bad english
HELP MEEEE plss.
thnx for all help
Click to expand...
Click to collapse
You hardSPL'ed your X1 correct, now you need to download the ROM you want (stock or cooked).
And follow the steps from Step 2 here:
http://forum.xda-developers.com/showthread.php?t=446070
gl
Lokatho said:
You hardSPL'ed your X1 correct, now you need to download the ROM you want (stock or cooked).
And follow the steps from Step 2 here:
http://forum.xda-developers.com/showthread.php?t=446070
gl
Click to expand...
Click to collapse
dude
he explain for fixes
"Attention! Couldn't do this on a Vista machine, had to use my XP notebook!
- Download the file you want to use and rename it from *****.image to ****.image.nbh
- Run NBHUtil
- Go to "Extract NBH" tab
- Choose *****.image.nbh
- Now you should see something like this:
Model ID: KOVS*****
Target CID: 11111111
Version: 1.02.932.3
Language: DEU Remember what it says here. Could be something else for you, depending on the language of the file you want to use!
Chunk Size: 64
- Click the "Extract" button next to OS:
- Save it as OS.nb
- Go to "Build NBH" tab
- Select the X1 as model
- Set language to the value you should remember ;-)
- Click on "..." next to OS:- Select the previously extracted OS.nb file
- Click "Build NBH"
- Save it as "Kovsimg.nbh"
Now you can continue with step 1 or 2.
but ..
this step
- Click on "..." next to OS:
not posibble
because look at the picture havent it? "...." how can be? pls help me
I'm not sure if I understand your problem, but why don't you follow this procedure http://forum.xda-developers.com/showthread.php?t=445662
"
0. Make sure x1 is hard-spl first - this is OK in your case
1. Make sure yr micro-sd is formatted w/ fat-32 - if you have no data on your card better format it again.
2. rename the image file (normally "ruu_signed.nbh") to Kovsimg.nbh, copy that to the micro-sd, and put that it yr X1
3. Bring x1 to boot-loader mode by turning off the x1 completely. Hold the "volume down" button on the right, and hold the power on button until you see the tri-color screen.
4. Then follow the on-screen instruction
"
5. After successful flashing remove battery for while
6. Optionally - do hard reset combo: press & hold two silver buttons under screen and press for short while power button, then follow the on-screen instruction
If you have no special reason it is better to use this method for flashing every rom.
netbat said:
I'm not sure if I understand your problem, but why don't you follow this procedure http://forum.xda-developers.com/showthread.php?t=445662
"
0. Make sure x1 is hard-spl first - this is OK in your case
1. Make sure yr micro-sd is formatted w/ fat-32 - if you have no data on your card better format it again.
2. rename the image file (normally "ruu_signed.nbh") to Kovsimg.nbh, copy that to the micro-sd, and put that it yr X1
3. Bring x1 to boot-loader mode by turning off the x1 completely. Hold the "volume down" button on the right, and hold the power on button until you see the tri-color screen.
4. Then follow the on-screen instruction
"
5. After successful flashing remove battery for while
6. Optionally - do hard reset combo: press & hold two silver buttons under screen and press for short while power button, then follow the on-screen instruction
If you have no special reason it is better to use this method for flashing every rom.
Click to expand...
Click to collapse
ye dude i know this step but
i was wrote how to do Kovsimg.nbh" explain
i have problem this step
do u explain me?
(srry my bad english)
netbat said:
I'm not sure if I understand your problem, but why don't you follow this procedure http://forum.xda-developers.com/showthread.php?t=445662
"
0. Make sure x1 is hard-spl first - this is OK in your case
1. Make sure yr micro-sd is formatted w/ fat-32 - if you have no data on your card better format it again.
2. rename the image file (normally "ruu_signed.nbh") to Kovsimg.nbh, copy that to the micro-sd, and put that it yr X1
3. Bring x1 to boot-loader mode by turning off the x1 completely. Hold the "volume down" button on the right, and hold the power on button until you see the tri-color screen.
4. Then follow the on-screen instruction
"
5. After successful flashing remove battery for while
6. Optionally - do hard reset combo: press & hold two silver buttons under screen and press for short while power button, then follow the on-screen instruction
If you have no special reason it is better to use this method for flashing every rom.
Click to expand...
Click to collapse
i copy standart stock my m.sdcart and boot my phone but only "serial" on 4 color screen how to use my msdcard?
step by step:
1. you wan to have stock rom.
You go to http://blog.fastgsm.com/sonyericsson/r3a-software-for-sony-ericsson-xperia-x1/ and download file you want.
For example file for "XPERIA X1 Generic UK R3AA010 Software Update" is "APP_SW_X1i_GENERIC_UK_CDF1215-1832_KOV_R3AA010.exe"
2. Now double click on this file in windows and unpack it. You will get another file something.image or whatever.
3. rename this file to kovsimg.nbh
make sure you can see in windows files extensions like .exe or .nbh
4. copy kovsimg.nbh directly on your sd card
5. now you should be ready for update
If you do this and boot loader can't find file - format your sd card again (not quick format bur normal format).
I hope this will help.
netbat said:
step by step:
1. you wan to have stock rom.
You go to http://blog.fastgsm.com/sonyericsson/r3a-software-for-sony-ericsson-xperia-x1/ and download file you want.
For example file for "XPERIA X1 Generic UK R3AA010 Software Update" is "APP_SW_X1i_GENERIC_UK_CDF1215-1832_KOV_R3AA010.exe"
2. Now double click on this file in windows and unpack it. You will get another file something.image or whatever.
3. rename this file to kovsimg.nbh
make sure you can see in windows files extensions like .exe or .nbh
4. copy kovsimg.nbh directly on your sd card
5. now you should be ready for update
If you do this and boot loader can't find file - format your sd card again (not quick format bur normal format).
I hope this will help.
Click to expand...
Click to collapse
i understand dude
itry FAT & FAT32 format (no quick format)
but i cant
im not stupid
i put m.sd card on xperia
it write serial on screen
how can? i do??
ufkozcan said:
i understand dude
itry FAT & FAT32 format (no quick format)
but i cant
im not stupid
i put m.sd card on xperia
it write serial on screen
how can? i do??
Click to expand...
Click to collapse
There are some SDcards that don't work with the flash by SDcard method.
So you'll have to try with flashing with your pc.
Lokatho said:
There are some SDcards that don't work with the flash by SDcard method.
So you'll have to try with flashing with your pc.
Click to expand...
Click to collapse
ok i will try
how?
1 - download the attached CustomRUU
2 - extract and place in the same folder as your *.nbh ROM file
3 - connect your phone with pc (activesync or windows mobile device center)
4 - when connected execute CustomRUU and follow the steps
5 - wait until finished (may take a while)
gl
Lokatho said:
1 - download the attached CustomRUU
2 - extract and place in the same folder as your *.nbh ROM file
3 - connect your phone with pc (activesync or windows mobile device center)
4 - when connected execute CustomRUU and follow the steps
5 - wait until finished (may take a while)
gl
Click to expand...
Click to collapse
thats ok thnx dude
now "APP_SW_X1i_VFE_UK_CDF1215-0285_KOV_R3AA013" last version
but boot screen write
KOVS110
SPL-0.72.0LiNex
microP1-787
microP2-707
is it normal?everything is orjinal? ??
idon think its normal SPL
how to return normal SPL? (for i want to use sony ericsson update program)
iwant to remove it

[GUIDE] STOCK-2-CYANOGEN / no longer updated after 4.2.1

NOTE: Reference Purposes Only, No Longer Maintained by OP (09/11/2009).
REMEMBER YOU BRICKED YOUR PHONE, NOT ME!
I AM NOT RESPONSIBLE FOR WHAT YOU DO WITH THIS INFORMATION.
ROGERS PHONES ARE ROOTED IN A DIFFERENT WAY
PLEASE FOLLOW THE ROGERS ROOT GUIDE
UPDATED 10/07/09 Installing CM 4.1.999
UPDATED 10/18/09 Installing CM 4.1.9999
UPDATED 10/25/09 Installing CM 4.2.1
Required Materials:
G1 / Dream
Micro SD card reader (phone will work in MOST cases)
Computer with Internet connection
USB cable for phone
Data Plan
_________________________________________________
Format your SD card using the FAT32 Filesystem:
1) Connect your sdcard to the computer using a card reader
2) A new removable disk should show up on your computer.
3) Right click it and select Format
4) Select FAT32 as the file system type.
5) Click the Start button
Download Everything Here
FILE 1 Download and unzip the RC29 or RC7 image file. Copy the DREAMIMG.nbh file to the SD card. (RC29 for US, RC7 is for UK)
FILE 2 Download cm-recovery-1.4.img or RA-dream-v1.5.2 and copy it to your SD card.
FILE 3 Download the Hard SPL and copy the zip file to the SD card.
FILE 4 Download the "1.6 Recovery Image" for your Dream/G1/ADP1 or for your Magic/ION/MT3G (This is NOT a recovery image, it is a ROM that you can flash from recovery)
FILE 5 READ THE FIRST POST and download the latest Cyanogen stable ROM then copy it to your SD card
STEP 1: DOWNGRADE
Our first step is going to downgrade your phone to RC29, This is like removing Windows XP Service Pack 3 and installing Windows XP Service Pack 1. It allows us to use a security flaw to gain root access. This section is going to use FILE 1 from the downloads
1) Turn the device power off.
2) Hold Camera button, and press Power button to enter bootloader mode.
3) You should see a gray/white screen with instructions to flash your phone with the update on your SD card.
4) As per the on-screen instructions, press the Power button to start upgrade procedure. DO NOT INTERRUPT THIS PROCESS.
5) After it is finished, perform the restart your phone. (May take up to 15 minutes to boot)
6) Complete the setup process for gmail.
STEP 2: ROOT
Your phone is now downgraded and we can use the security flaw to replace the recovery image. The "recovery" is kinda like a boot disk on your computer, we use this to delete, modify, and create system files while they are not in use my the ROM. The recovery will be used when ever you flash pretty much anything to your phone.This section is going to use FILE 2 from the downloads
1) At the home screen hit the enter key twice, type "telnetd" and press enter. IGNORE WHAT THE SCREEN IS DOING
2) Press Home
3) Goto the market and download "Telnet"
4) Open Telnet and connect to localhost : 23
5) Press enter and you should see a #
6) Now type the following and press enter at the end of each line
mount -o rw,remount -t yaffs2 /dev/block/mtdblock3 /system
cd sdcard
flash_image recovery cm-recovery-1.4.img
cat cm-recovery-1.4.img > /system/recovery.img
7) Press the home button
STEP 3: HardSPL
Now we are going to change the bootloader or "SPL". Currently your SPL will only allow you to flash ROMs that HTC or your carrier have produced. This new "HardSPL" will allow us to flash ANY ROM we want. This section is going to use FILE 3 from the downloads
1) Hold power and turn the phone off
2) Start up in recovery mode by holding home and pressing power.
3) You will now enter recovery mode.
4) Press Alt-S to apply the update.zip from the SD card. This is the spl you downloaded.
5) After the update is complete, hold Home and press Back to restart. (May take up to 15 minutes to boot)
STEP 4: ROM
Now we are going to flash the latest ROM from Cyanogen. This is your new "Operating System". This section is going to use FILE 4 and FILE 5 from the downloads
1) Hold power and turn the phone off
2) Start up in recovery mode by holding home and pressing power.
3) You are now in recovery mode.
4) Press Alt-W to wipe all data
5) Press Alt-A to apply any zip from sd
6) Choose signed-dream_devphone_userdebug-ota-14721.zip (You won't see the entire filename)
7) When it is done it will ask you to reboot to complete the installation. Press Home+Back
8) You will be returned to the recovery screen in a few minutes, be patient.
9) Press Alt-A to apply any zip from sd
10) Choose update-cm-4.2.1-signed.zip
11) After the update is complete, hold Home and press Back to restart. (May take up to 15 minutes to boot)
12) Complete the setup process
You can NOT run HERO ROMs YET!!!!!!!
You may want to partition your SD Card (See Post 3 or Post 4)
BACKUP FREQUENTLY
Remember that your nanddroid backups are on your SD card so be sure to save them if you do any partitioning.
- Upgrading from CM4.1.11.1 or below to 4.2.XX
Download File 4 and File 5 from first post above.
1) Hold power and turn the phone off
2) Start up in recovery mode by holding home and pressing power.
3) You are now in recovery mode.
4) Press Alt-W to wipe all data
5) Press Alt-A to apply any zip from sd
6) Choose signed-dream_devphone_userdebug-ota-14721.zip (You won't see the entire filename)
7) When it is done it will ask you to reboot to complete the installation. Press Home+Back
8) You will be returned to the recovery screen in a few minutes, be patient.
9) Press Alt-A to apply any zip from sd
10) Choose update-cm-4.2.1-signed.zip
11) After the update is complete, hold Home and press Back to restart. (May take up to 15 minutes to boot)
12) Complete the setup process
Upgrading from CM4.1.99 or higher to CM4.2.XX
Download File 5 from first post above.
1) Hold power and turn the phone off
2) Start up in recovery mode by holding home and pressing power.
3) You are now in recovery mode.
4) Press Alt-B to run a nandroid backup
5) Press Alt-A to apply any zip from sd
6) Choose update-cm-4.2.1-signed.zip
7) After the update is complete, hold Home and press Back to restart. (May take up to 15 minutes to boot)
The functions of the utility script has been replace by the Amon RA recovery.
http://forum.xda-developers.com/showthread.php?t=566669
How to easily esperiment with linux-swap partition sizes
So you want to try out different linux-swap sizes, but do not want to lose your data on your sdcard each time? Then this is the guide for you.
To start you will need you cyanogen's 1.4 recovery image (good thing you followed the above guide eh) and some basic math skill.
SETTING UP YOUR SDCARD
Well for this to work you will need to partition your sdcard a certain way, but only once for the entire card. BACKUP YOUR SDCARD!!!
To do this you will go into parted in the recovery console with these commands
Code:
parted /dev/block/mmcblk0
print
Do not leave this screen we will come back to it
After you type print you will want to look for the line that says
Disk Size /dev/block/mmcblk0: xxxxmb (you can fill in the numbers )
Click to expand...
Click to collapse
Now for the math. (i will explain some of the reason behind certain sizes then clear up the line)
first line in equation:
xxxxmb (total on card) - 96mb (it can be as large or as small as you want it but the highest i have seen people go with good results is 96mb)
so the first line will be:
xxxxmb - 96mb = zzzzmb
second line in equation:
zzzzmb - 500mb ( most people and guides suggest not to go over 500mb for ext2/3/4 so i shall do the same)
so the second line will be:
zzzzmb - 500mb = yyyymb
complete equation:
xxxxmb - 96mb = zzzzmb
zzzzmb - 500mb = yyyymb
;where xxxx = total mb (going to be the end point for linux-swap as well), zzzz= end point for ext2/ beginning point for linux-swap yyyy = end point for fat32/ beginning for ext2
So now with the equations out of the way (yes, I do like math, thank you very much) type this into recovery while still in parted
Code:
rm 1
rm 2 (if it exists)
rm 3 (if it exists)
(for the next commands obviously you will plug your own numbers in)
mkpartfs primary fat32 0 yyyy
mkpartfs primary ext2 yyyy zzzz
mkpartfs primary linux-swap zzzz xxxx
print (to verify it worked)
quit (ignore the update etc/fstab comment)
upgrade_fs
reboot
Now that was the hard part, the next part is really easy.
TO CHANGE LINUX-SWAP SIZES EASILY
With the setup above your linux-swap partition will be 96mb by default, to change it you will need to do the following
Go to the recovery console and type
Code:
parted /dev/block/mmcblk0
print
Again do not leave this screen for we shall return momentarily
After you type print, it will show you the sizes of your 3 partitions. The third partition is the one we want to look at. You will need to get the start and end points for this partition.
(for ease of writing this guide, x will be the start and y will be the end)
For a 64mb swap partition you will want to follow this equation:
y - 32mb = y* (y* will be the new endpoint)
For a 32mb swap partition you will want to follow this equation:
y - 64mb = y* (y* will be the new endpoint)
Now go back to your phone that is still in parted and type (of course you substitute in your numbers)
Code:
resize 3 x y*
quit (ignore etc/fstab comment)
reboot
There you go, that is how you quickly and easily change the size of your linux-swap partition without ever taking the sdcard out of your phone.
Also you will need to edit your user.conf and userinit.sh to reflect the new size of your linux-swap partition. Here are instructions for how to edit your user.conf. (thank you kingklick)
Lol why do we have so many guides of the same thing
ThR1LL said:
Lol why do we have so many guides of the same thing
Click to expand...
Click to collapse
because some people suck at following the older guide koush made (the one-click exploit will be patched soon) and this has links to newer roms, i didn't realize there was a more current version of koush's guide up, also this one has friendly pics
Also it's structured in a way that we can refer people back to it when they have a specific need like how to update their radio..... Goto step 6.
Oh and lets not forget that all of our ROMs will crash if you install apps2sd YET IT'S FREAKIN A STICKY IN THIS FORUM. The sticky also tells you to install cm-recovery-1.3.1.img.
^ great point/post AND thread. I wish I had this back in the day.
Can you add more info oon why to delete davlic AND a post on WTF a user file is/can do.
I still am not sure if i need to do that?
nice
not a a bad guide, we need to get a newer guide stickied
so got 1 vote from me
gridlock32404 said:
not a a bad guide, we need to get a newer guide stickied
so got 1 vote from me
Click to expand...
Click to collapse
and you've got a vote from me to be the president in 2016
Great guide. Stickied.
ivanmmj said:
Great guide. Stickied.
Click to expand...
Click to collapse
Thank you for making this a sticky
Wow an honory member of the wrecking crew got top spot sticky, ****. We are essential to xda.
Good job fingerlicken
Data Plan or Wi-Fi?
Hi finger, or anyone with the kindness to help...
This guide is the most perfect one I think....but I still have a question
Is it necessary to have a Data Plan? or Wi-Fi will do the job? Do I have to unlock my phone before I start the guide? or It doesn't matter?? Thanks!
pliundemix said:
Hi finger, or anyone with the kindness to help...
This guide is the most perfect one I think....but I still have a question
Is it necessary to have a Data Plan? or Wi-Fi will do the job? Do I have to unlock my phone before I start the guide? or It doesn't matter?? Thanks!
Click to expand...
Click to collapse
you can follow this thread for when after you apply the DREAIMG.nbh to activate your phone, so you can finish rooting it, this is the only time you should have to use this method to activate your phone. once you install a custom rom based on the ADP phone you can skip the activation till you have wifi set up.
New AndPart program is posted. This does not partition the drive for you it is simply a guide that does the math for you.
See what you guys do to me. Leavin me out in the cold.
supremeteam256 said:
See what you guys do to me. Leavin me out in the cold.
Click to expand...
Click to collapse
you left yo self out in the cold by being all like yeah "i'm hungry now, david" you got sent the same email (i didn't even get it originally, but i am still that good) everyone else did
So it appears there are several methods of backup the ext partition. Some zipped and some not. What is the easiest (can't F it up) method for terminal, recovery, and adb? I'm going to assume we should stay away from the zipped method.
I got terminal emulator commands down to 3 for backup and 2 for restore. in FAQ
david1171 said:
you left yo self out in the cold by being all like yeah "i'm hungry now, david" you got sent the same email (i didn't even get it originally, but i am still that good) everyone else did
Click to expand...
Click to collapse
LOL, you still got any chinese left. My fishsticks and tator tots just didn't cut it.

[Solution] How to make an uploadable image of an SD backup image

First your phone must be CID unlocked to make a backup image
Programs you will need
MTTY
USB Image Tool "Developer’s web site"
Instructions:
1. Open ActiveSync go to Connection Settings and uncheck “Allow USB connections”.
2. Put the phone in boot loader mode.
Turn the phone off press and hold the Camera key, now insert the USB cable, Keep holding the “Camera” key until you get the boot loader screen.
3. Insert formatted SD card, 128mb or larger.
4. Start MTTY select Port: = USB click the “OK” button, you don’t need to change anything else.
5. Type “set 32”
“CMD55 failed” = SD card not properly inserted.
“g_cKeyCardSecurityLevel = 0” = CID unlocked, if not you didn’t read the first line of this post.
6. Type “r2sd all” this will create a full backup, don’t interrupt the process, wait for it to finish.
7. Type “ResetDevice”
8. Remove SD from phone, insert SD to computer.
9. Open USB Image Tool, select “Device Mode” from the drop down list, select the SD card and click “Backup”.
To write the SD image to an SD card select the SD card you want to write to and click “Restore”.
Now we move on to restoring the image to the phone.
With the phone on, insert the SD card in the phone, press and hold the “Camera” key and soft reset, keep holding the “Camera” key.
When asked, “Download SD Image?” release “Camera” key and press the “Voice Dial” key.
Hopefully that covers it.
This could be a viable way for people who have broken USB ports to restore/upgrade their phones.
Current images:
These are official stock ROMs
Cingular 8125 G3
T-Mobile MDA G3
T-Mobile MDA G4
I will list more as I make them
Reserved For Future Post
Tried image on my phone and it did not work. So I opened MTTY and ran ( set 32 ) and got
Code:
CMD55 failed
GetDeviceCID: Error - InitDecoder
g_cKeyCardSecurityLevel = FF
I believe FF means it is locked.
So I tried info 1 which gave 2.21.Olipro.
Sounds like I broke the HardSPL but did not change the SPL from 2.21.Olipro.
Sounds like truly a brick now.
You are correct.
g_cKeyCardSecurityLevel = FF
Means CID locked.
I noticed a few downloads have been made but no comments.
What I want to know:
1. Did the ROM images work?
2. Do you have a broken USB port?
3. Did you have another reason for downloading the image?
What im trying to get from these questions:
1. Has anybody been able to use these images?
2. Should I continue to upload images?
3. Was this thread pointless?
-MyHTC- said:
I noticed a few downloads have been made but no comments.
What I want to know:
1. Did the ROM images work?
2. Do you have a broken USB port?
3. Did you have another reason for downloading the image?
What im trying to get from these questions:
1. Has anybody been able to use these images?
2. Should I continue to upload images?
3. Was this thread pointless?
Click to expand...
Click to collapse
Well, i'm about to try to use the T-Mobile G4 image on my WWE QTEK9100 G4. Its stuck in the screen right after bootloader (that shows the versions) and i can't get it to boot or flash anything. I just want to get a ROM in it that boots so i'll see if that works.
Thank you for responding.
I noticed from your other thread that your using the hard SPL and your having problems installing ROMs.
With the hard SPL installed im not sure this method could help you, please let me know if it does.
If your still having problems let me know I will try to help.

Boot freeze

Hello
i have a TD2 (r - 4.49.25.91 / d - LouMeiYin D) and it freezes before booting (when the radio and rom are shown at the bottom in red). I tried soft reset (it doesn't work), hard reseting, changing rom to stock and the back, and tried several radios (all these changes work but doesn't solve the problem). When it freezes i can't turn it off from the power button but need to remove the battery. Tried starting it without a sim and still doesn't work.
The phone shut down by its own and can't turn it on since.
Any advice would be welcome,sorry for the bad english.
Thank you
You may have a bad ROM file, try downloading again and reflash.
Also, make sure to remove SD card to eliminate any UC interference.
flashed with Duttys Topaz HG R13 [5.2.23569.5.5.0], still the same problem, stops at touch diamond 2, also flashed with stock rom.
the sd card is out.
cheregi said:
flashed with Duttys Topaz HG R13 [5.2.23569.5.5.0], still the same problem, stops at touch diamond 2, also flashed with stock rom.
the sd card is out.
Click to expand...
Click to collapse
and you've installed HSPL?
i have hard spl 1.83 installed
i've now instaled HSPL 2.51 and i'll flash again
Come to think of it, that probably was your issue.
HSPL 1.83 is only good on slightly older ROMs where 2.51 is current.
2.51 should solve your issue.
it won't boot with stock ROM,
hard reset = (i've pressed the power buttons + VolUp+ VolDown
-recieved "this will delete all your personal data ... press VolUp to restore"
- pressed VolUp - restore ... completed, press volup to boot and still stops at the same screen)
no, flashed Duttys Topaz HG R13 [5.2.23569.5.5.0] with HSPL 2.51 and still the same problem.
i can't figure out why it won't go past this stage...
I gotta go, but look into MTTY to reflash your drive.
Something seems corrupt.
Sorry man.
reflashed with mtty, and still the same problem. i think i'll use it as a brick
"
Cmd>set 14 0
HTCST ÚÈÒHTCE
Cmd>task 29
Format BINFS start
CE start start block=321, total block=3775
ERASE block 2343 FAIL !!!
Write 0xFF start page=0x5040, total page=0x3AFC0
Format BINFS end
Cmd>task 8
"
and also
"
Cmd>task 28 55aa
Format start
Fill RSVD information for block 288 to 321
Storage start sector=0x15800, total sector=0x25240
Storage start block=1409, total block=2377
Total Bad Block in CE: 0
Erase physical block from 1699 to 4096
formatstorage Bad block found: 2631
Format end
Cmd>task 8
"
no ideas anybody?

Categories

Resources