Related
I decided to make my own kickstand for my HD2 and am pleased with the result. The benefit of how I did it is you don't need to carry any seperate accessory as the stand is built into the case so you will always have it with you as long as you have your phone. Nothing else to lose.
To make one you will need a stiff snug fitting case, cutting knife, pen and cutting board. These cases are inexpensive so if you make a mistake its not the end of the world.
Just cut 3 slots into the case. Make sure you draw straight lines inside the case and that the flap is centered. Don't make the flap too narrow as you want some strength. You can make it as wide as you like. You may want to make a template (on card) of the rectangle flap first and then draw around it inside the case. Make sure the flap is not too long or too short. The bottom of the flap should be reasonably close to the edge of the case too.
To open the flap, just flex the plastic by firmly pulling it with your thumb towards the center, or use your fingernail to catch the edge. To close it just click it it back to its original position and it stays in nice and flush. It will not accidently pop open. The flap is virtually invisible when closed.
It works brilliantly. I am well chuffed!
LoL very nice never thought about that... I have the same case, and it kinda might be useful ! nice tip cheers
Wouldn't the flap start to wear after a while and the opening degrade over time?
I don't think it would wear over time. I did not score or crease the hinge so it will never snap off. It is just flexed. The case is a flexible material. Nothing to degrade.
I mean like clipping of the rubbery material and the flap starts to stay open. Over time.
It shouldn't stay open as the way it's been cut and because of the thickness it CLICKS into place. Wedged in. It's a little tricky to open so I can't see it springing open by itself. Time will tell but think it should be fine.
tboy2000 said:
It shouldn't stay open as the way it's been cut and because of the thickness it CLICKS into place. Wedged in. It's a little tricky to open so I can't see it springing open by itself. Time will tell but think it should be fine.
Click to expand...
Click to collapse
I think the concern is that with any press-fit or clip-fit flap, the friction will wear out the material slowly and with time become lose.
Even the HD2 OEM battery door, if opened/closed enough time, will become closed
The question becomes, then, whether the flap will outlast the device
The other idea to make the flap last longer is the ANGLE the cut so that instead of cutting perpendicular to the surface of the case, you cut slanting away from the way the flap open. This way you create a little lip for the flap to lock into.
felixdd said:
The other idea to make the flap last longer is the ANGLE the cut so that instead of cutting perpendicular to the surface of the case, you cut slanting away from the way the flap open. This way you create a little lip for the flap to lock into.
Click to expand...
Click to collapse
I thought of that and it was going to be my second attempt if this first attempt did not work out but I was surprised to find it click into place even with a non angled cut.
I also thought about adding a small bit of tape to the inside lip of the flap so you could pull it open, but dismissed it for looking unsightly.
Also thought about a magnetic closure. So far so good as is. As I say time will tell but I have been opening and closing it a lot so far and still no problems.
is that an ebay case? link to seller
ya if i do this i'm definitely going to angle cut it.
methodz this is the one I bought. Super cheap:
http://www.netimes.com/shop/resin-soft-jelly-case-for-htc-hd2-t8585-htc-leo-p-2455.html?cPath=80_731
I gotta say, I've seen a lot of DYI stuff on here (charging dock through a box, lanyard through battery cover, piggyback extended battery, etc), but this is one of the most ingenious thing I've seen. Kudos to you!!
..and for those who are questioning the durability of this, don't get the ultra thin gel case. Get one with a good amount of thickness so it doesn't flex too easily. Don't worry if it doesn't fit snuggly back on the case when you done...because it will if you get a good gel case. (I've done cutting to a few of my cases on other phones..no case for HD2 yet)
Very nice indeed!
I'm going do the same with mine.
Nice one mate. I too have the same type of case and would never have thought of this! I can see why people are talking about it losing its strength over time, and I too imagine that it would eventually lose the will to actually stand the device up, or click back into place - one or the other - but I would only use this "feature" maybe once or twice a week, so it would take a long time to have any detrimental effect on the case. But let's face it.... it's dirt cheap and replaceable!
Very clever idea mate - thanks a lot
I think it would be great if some case manufacturer took this idea up and made a professional version. I should get royalties of course.
I have noticed after prolongued time in the open stand up position, it does slightly spring open after closing it - however storing it on its back for a short time DOES make it stay flush again so no big issue.
I may try an angled cut next time. Think I will order a couple more cases and experiment on the most optimal design.
Wouldn't it be funny if you cut it the opposite way the accelerometer turns? Ha.
This is an AWESOME idea. $4.00 for a case? Fix def worth the "degraded" possibility.
Yes make sure you cut the flap in the right direction to your landscape view. Very important!
Sure you've seen this anyway but pocketnow.com wrote this up, kudos:
http://pocketnow.com/how-to/make-your-own-htc-hd2-kickstand
It made wmpoweruser.com news too!
http://wmpoweruser.com/?p=14723
Oh and if anyone else wants to try it I found it on ebay too for 4.00 GBP
http://tinyurl.com/ygoeapy
well done tboy2000. your 5min of fame!
Hi all,
I have a desktop cradle which i use in the office and the otterbox commuter case which i use daily.
i have gotten my desktop dock from here.
http://cgi.ebay.com.sg/ws/eBayISAPI.dll?ViewItem&item=380267286428&ssPageName=STRK:MEWNX:IT
i am satisfied with the dock but i am finding it annoying to have to remove my otterbox case everytime i want to charge/sync.
is there a dock/cradle out there which can do the same without the need to remove the case?
I am aware of Desk Genie non slip charging desk stand but i read somewhere that it does not sync. (can anyone confirm this?)
any other recommendations are greatly welcomed.
has any one tried this
http://www.netimes.com/shop/angne-d...tc-hd2-t8585-htc-leo-p-2533.html?cPath=80_731
or this
http://www.netimes.com/shop/non-sli...p-2384.html?cPath=445_720&number_of_uploads=0
any feedback or help would be appreciated
The desk genie for me was a bit of wasted purchase:
The phone just slips off it. I think the reason is that the shiny battery-cover just won't grip, as heavier items, such as a digital camera/old WM phone stick to it like a charm. I put sticky brown tape all over the back of my phnoe and it was slightly better, but on the whole I'd say it's a don't-buy.
re: Syncing, it's a bit stupid. You plug a mini-usb into the back of the unit, and then a small power-lead with a micro attachment also comes out of the back as a charge = no syncing. As the device does have a USB hub, you can run another cable from a USB port to the phone, but overall it's a bit messy. One of those tiny mini-USB cables would do it (the 6cm long ones), but overall you still end up with a cable sticking out the side.
Thanks for replying...
i was almost gonna one of these...
which is a cheaper alternative to the desk genie...
have you tried it with case on??
as that is my concern as i do not wanna remove my cases all the time i wanna use a dock
smeddy said:
The desk genie for me was a bit of wasted purchase:
The phone just slips off it. I think the reason is that the shiny battery-cover just won't grip, as heavier items, such as a digital camera/old WM phone stick to it like a charm. I put sticky brown tape all over the back of my phnoe and it was slightly better, but on the whole I'd say it's a don't-buy.
re: Syncing, it's a bit stupid. You plug a mini-usb into the back of the unit, and then a small power-lead with a micro attachment also comes out of the back as a charge = no syncing. As the device does have a USB hub, you can run another cable from a USB port to the phone, but overall it's a bit messy. One of those tiny mini-USB cables would do it (the 6cm long ones), but overall you still end up with a cable sticking out the side.
Click to expand...
Click to collapse
I don't blame the Genie, I blame it on the HD2's too-friction-less back. Heavier, bulkier items (such as your typical Panasonic digicam) stuck to it like a charm (I note I already said that, but hey, worth repeating). I do not have other covers to hand to test it, but I do keep my phone in a fake-leather walleet (off eBay, love it), and the phone - despite being a lot heaver due to the wallet - does stick to the Genie, so I do reckon other covers will stick quite well.
If I can test others i will report back.
smeddy said:
The desk genie for me was a bit of wasted purchase:
The phone just slips off it. I think the reason is that the shiny battery-cover just won't grip, as heavier items, such as a digital camera/old WM phone stick to it like a charm. I put sticky brown tape all over the back of my phnoe and it was slightly better, but on the whole I'd say it's a don't-buy.
re: Syncing, it's a bit stupid. You plug a mini-usb into the back of the unit, and then a small power-lead with a micro attachment also comes out of the back as a charge = no syncing. As the device does have a USB hub, you can run another cable from a USB port to the phone, but overall it's a bit messy. One of those tiny mini-USB cables would do it (the 6cm long ones), but overall you still end up with a cable sticking out the side.
Click to expand...
Click to collapse
I don't agree. Its a fact that it wont grip especially when one uses a silicon case. But I've placed 2 pins just beneath the rubber so it will always hold the phone. I am using it now for some time.
ymtan said:
......
http://www.netimes.com/shop/non-sli...p-2384.html?cPath=445_720&number_of_uploads=0
Click to expand...
Click to collapse
I have it and works nice
- without case
- with leather (flip) case
- with solicon case (soft)
- with hard plastic case
ciubeca said:
I have it and works nice
- without case
- with leather (flip) case
- with solicon case (soft)
- with hard plastic case
Click to expand...
Click to collapse
Thanks for your info.
will probably get this to try seeing it is not as expensive as desk genie
sorry to bump an old thread, does anyone have any suggestions for the original post?
thanks
What is the ideal case for your Nook Color?
Is it one that is available or not?
What are some of the features you would like it to have?
Do you want a fold case that covers the screen?
Is the micro usb port in a convenient location?
Looking for some ideas. Working on a shell now for a mold. Not sure if anything will come of it but want to see what you all are looking for in a case. Feel free to post your thoughts. Thanks.
I would like to see a one sided hard cover that can protect the screen when not in use and snap onto the rear when in use. Probably use the typical four corner frame system you see in many cases so nothing is obstructed.
Also, have a stand "system" so that when it is snapped to the rear you can prop up the NC. Maybe something like what you see on back side of keyboards. And like some keyboards I've seen, have different levels of lift. One lift level that slightly raises the NC off the surface, for typing and such. Another lift level that is like the leg stand you see on the EVO 4G or Archos 70, for video/picture viewing and the like.
Heh. First post around here. Been meaning to chime in on a thread and this is the perfect one to start. Only because I've been looking for something I described but there is nothing out there yet.
I'm looking for an inexpensive silicone gel skin, something I'd keep on pretty much all the time. I'm also keeping my eyes open for sturdy travel case.
There seem to be choices out there for both, I'm just waiting a bit for more of them to hit ebay.
I missed your last question about the micro usb port. IMO its not in a good location because its awkward when trying to read while charging, particularly when reclining or lying down. I'm concerned about putting pressure on the usb cable, especially considering its not just a standard cheap cable. Not sure how a case will help this, though.
drp1 said:
I missed your last question about the micro usb port. IMO its not in a good location because its awkward when trying to read while charging, particularly when reclining or lying down. I'm concerned about putting pressure on the usb cable, especially considering its not just a standard cheap cable. Not sure how a case will help this, though.
Click to expand...
Click to collapse
ill be trying out a few designs once the mold sets. i can add a ribbon cable in the case to move the USB port to the sides which I might try. trying to keep it thin but actually worth putting on.
techboydino said:
ill be trying out a few designs once the mold sets. i can add a ribbon cable in the case to move the USB port to the sides which I might try. trying to keep it thin but actually worth putting on.
Click to expand...
Click to collapse
Are you designing desktop/multimedia cases as well? I would love additional speakers on the NC and also a magnetic swivel X mount stand for desktop use.
My ideal case is not available yet. It is an envelope-like case that will allow me to pull the Nook out and use it naked. Something in nice black leather.
Something similiar to the covers of the TI calculators, with a little more thought about aesthetics obviously.
A 90deg connector or adapter would be nice. Then run the cable through the corner loop thingie.
Cheers,
kev
bugeyed1 said:
A 90deg connector or adapter would be nice. Then run the cable through the corner loop thingie.
Cheers,
kev
Click to expand...
Click to collapse
Good Idea, I may try that out.
Im not any sort of professional or anything, but I do have access to some pretty sweet resin's and molding equipment. Carbon fiber is the idea, but the glass mold and how I want to do the front part comes first. Ill keep the thread updated.
ideal nook case
looking for something very close to this case
http://www.amazon.com/gp/product/B0040VNRTG/ref=oss_product
just substituting the swivel belt clip for a kickstand
i like the idea of moving the usb jack to another spot but i think that would add alot of cost and effort to the case build
Rube Goldberg lives; or, is this even possible?
You asked for the ideal, here is mine. Not at all sure it is doable....
1. In the interest of keeping the total package as slim as possible, no back, unless it is necessary to support other features.
2. [Front] cover has a slot for a pad of paper and/or corner slots for index cards.
3. [Front] cover is hinged on the right (I'm right handed and I want to be able to write easily).
4. [Front] cover has a foldover flap to keep the paper or cards from contacting the screen when the cover is closed.
5. The cover can fold 180 degrees so that the cover lies flat against the back of the tablet.
6. The cover can support the Nook as an easel in landscape mode.
7. The cover can support the Nook as an easel in portrait mode - this might involve some sort of short extension legs or other support to raise the lower edge of the Nook an inch or so (and this might help with the need to plug in the USB connector at the bottom).
8. Bonus points for the ability to fold out a handle attached at the lower left corner when in portrait mode, sort of like a hand mirror.
9. And of course it should be strong, light, durable, elegant, and less than $40 US.
I'm ready to order as soon as I see the pictures of the finished product.
Thanks for the ideas everyone. Haven't worked on it in a few due to being out at CES. Unfortunately there were NO cases out there. Working with Speck to find something but tried everything else and could not even find a nice slip cover. Otterbox said they are testing designs so no real info there either.
My ideal case is something like
http://shop.brando.com/samsung-galaxy-tab-case-with-bluetooth-keyboard_p05269c0299d057.html
this.
Bluetooth keyboard case, waiting for bluetooth to work for NOOK!! and I could use it as a netbook and a tablet. IDEAL.
This is my cheap (free) case for my nook color. It’s the zippered case for my trucks instruction manual. The patch covers the ford symbol; if I need to hide it in plain sight I can pull the patch off and leave it in the back seat. It fits perfectly and there is a plastic divider on the inside I can put business cards and a small pad of paper (as others have asked). All I keep in it is a set of skullcandy headphones in an microfiber Oakley sunglass bag for cleaning the screen.
michael
-"I learned a very valuable lesson on my travels, Tucker. No matter how bad things might seem..."
-"They could be worse?"
-"Nope, no matter how bad they seem, they can't be any better, and they can't be any worse, because that's the way things fraking are, and you better get used to it Nancy. Quit yer *****ing."
Perfect case for the Nook Color
Before I bought my Nook, I had a Pandigital Novel that I bought on eBay.
In the same eBay search results page the Novel appeared on was a great case called BookArmor. Although it was $35, I bought it. And I haven't regretted it either.
The BookArmor case comes with a set of velcro-like pads that stick on the back of the tablet and allow it to be fixed to the case. The case itself is laminated steel and plastic covered with textured fabric. It zippers shut and the zipper sides are soft and stay out of the way when the case is opened. You have total access to all side buttons and ports. The inside surface that comes in contact with the screen is covered with a soft foam pad.
When I decided to get the Nook, I found out that the case I had for the Novel is the exact same case for the Nook Color. I really like this case and haven't even considered another one.
For more info go to extremeinkjet.com and click on BookArmor cases in the blue left-hand column. Pick any Delta 6 case ... there is a Nook Color one. Checkout their video at the bottom of the page.
It looks like this case is really popular too ... there aren't any left on eBay and the extremeinkjet site shows all out of stock for the Delta 6 case. Amazon shows one Delta 6 left for the Pandigital (same case) but it doesn't even show up for Nook Color.
I don't know if I'd call it perfect. But, I bought the B&N case with the vertical flap and ribbon with magnet on the end to hold it closed/open. It works well for me.
If they were available in store when I bought my nook, I would have also considered the silicone one. Although, if I went that route, I'd probably prefer the otter box version with the hard resin exterior an rubber liner. I would also have considered the black leather pouch one where you completely remove the nook to use it.
Alas, none of these were available to me when I made my purchase so I'm using what I have.
With either the otter box or the silicone I would gain a thinner form factor. But, I would never be able to completely cover the screen. With the pouch one, I would gain the thin form factor when using and would not add much when transporting. But, it's basically just a branded leather sleeve.
In the end, what drew me to the case that I bought was the vertical flap and ribboned magnet. 1 - with the horizontal flapped ones, the magnet does not flip around to hold the flap to the back of the case so it's open like a book with the flap dangling out the right side. 2 - with the vertical one that I got, you flip the cover over the top, move the magnet to the back to hold the cover in place and you have all your nooky goodness to go to town with!
Just my 2 cents.
jlh8733 said:
Something similiar to the covers of the TI calculators, with a little more thought about aesthetics obviously.
Click to expand...
Click to collapse
Wow...love love love this idea.
This would be great..a hard protective slide case.
This would definitely be a $$$ maker.
I bought a "Industriell Cover in Storm" cover and it works perfectly, very simple, protects the screen, and it's small.
I'm stealing your "DON'T PANIC" sticker on the back idea. thanks for reminding me.
Hi all,
I have recently switched to the Streak from owning all models of the iphone, and have not looked back. Such an awesome device, and android is great. Anyways, I had owned a case for my 3gs and Iphone 4 called the Mogotalk xd. It is a bluetooth/case/charger that keeps an extremely thin and very good bluetooth on the back of your phone. I have missed it very much, especially since the streak is huge and could really benefit from one of these...The product is very smart, and very thin...but this isn't a review, so you can check it out their site, which I can't link yet...just google or youtube it...
I contact ID8 support to ask if they would be making these cases for other devices, and they replied back that they would not. So, I decided to mod mine for my streak, and post it here in case anyone else wants to do the same. It came out very well I think, and was very easy...extremely useful...
I started by removing the felt lining (just peeled out), then, after messing around a bit, decided to just take an exacto knife to the rubber for the sides of the iphone. I cut right along the back of the case, so as to have a close fit. Pics attached ( I also cannot link pictures yet :-C)
I have 2 battery covers, so I then attached it with double sided tape (temporary, as I am looking for some way incorporate a kickstand next). I lined up the top of the case with the top of the battery cover. It still slides on fine. If someone wanted to, they could probably dremel the top of the case to fit perfectly on the battery cover, as the camera hole unfortunately is horizontal...and there are no electronics on the top half (bottom has charging port) The only thing you really lose is a few millimeters of thickness...but this thing is thin (still fits tightly in the car dock from dell) And now I have bluetooth that charges on my phone and is always with me. Really easy to do, and definitely worth it if you like talking on your phone, as this can be difficult with the streak. Let me know if you have any questions...you can pick this up on amazon or other sites for around 40-45 dollars..its worth it..
One thing to be careful of there is the battery compartment door. There's a power switch inside the Streak that's activated by a pin on the door and if the door moves your Streak will power down. This is a known problem with nothing on the door so I don't know how yours will behave with the extra weight/bulk hanging off it. I know good comfortable earpieces are hard to find so maybe you could incorporate the BT holder into another case instead of attaching it directly to the streak?
I thought about that, and it would be very easy for someone who wanted a case...however, I do not...The Case/bluetooth is extremely light, and for some reason, the battery cover now fits much more tightly in place..its not going anywhere...It would be really easy to just cut out out the back of a case, especially a silicone one, to fit...or to cut the top half as I said before and fit it into a hard case...
so i was staring at this GameKlip accessory and thought, I could probably make one myself. They sell for about $20 including shipping online. Why not save some $ since I had the material.
What I used:
1 piece of 3" long and 1/8" thick stainless steel wire ( I got from a welding shop )
some shrink tubing from an electronics store, to protect the mounting points on the controller.
lighter or hair drier to shrink the tubing.
2 pairs of pliers to bend the wire
1 Sharpie marker to mark my bending points.
Playstation 3 Sixaxis wireless bluetooth joystick.
you can design as you see fit, but i started by bending the wire in half like a big V
bent the curved part 1/4" down @ 180 degrees. this is my anchor point for the joystick. this part goes right between the thumb sticks at the back.
from there i went underneath the joystick, making small bends to follow the contours of the controller.
NOTE: this is where you slide small pieces of shrink tubing over the wire at any point you don't want scratches on your joystick. Keep adding more as you progress, if you make too many sharp bends, you wont be able to slide the tubing around the bends.
anyways from the bottom to the front the wire goes, again following the V shape and spreading towards the L1 and R 1 buttons.
from there I bent the wires up, again following the contours and adding shrink tubing. Every time i needed a bend, i marked the wire with the Sharpie first and eyeballed it. the great thing is if you mess up, just bend the wire back and try again.
After going to the top front of the joystick, i made mounting bends like the first one. now with two single wire ends instead. (see photo) went backwards a tad and curved back 180 deg foward again.
i bent the remaining wire into a smallish platform then back to the joystick again, aiming for the USB charging port for my final brace to hold the weight of the phone.
I finished off by joining the two loose ends at the bottom of the joystick again with the shrink tubing. Both ends in one piece of tubing.
now i need a cheapo eBay TPU rubber case to permanently glue/double side tape to the mounting platform.
In all it took me about an hour.
you can use a thicker gauge of wire to make the whole assembly stiffer, but that would be too hard to bend and possible damage your controller when putting it on or removing. I had to remove it many times during the build to test my bend angles and fit.
oh and if you're not feeling the MacGuyver-ness, buy a real one here: http://buy.thegameklip.com/
reserved
More pics without joystick
Nice work
thanks
on second thought, thicker,copper wire would be doable too, as you can easily solder the pieces any way you want, and its malleable enough to bend easily.
I thought about Aluminum Wire but its too soft and likely to come loose and make your hands all black from the oxidation. It would be light though
I may just tack weld a small sheet of metal to the platform part so i can stick a case on easier.
Maybe just punch some small holes in the TPU case and zip tie it to the frame....
Can we get a pic with the phone attached?
mr mystery said:
Can we get a pic with the phone attached?
Click to expand...
Click to collapse
He said in the OP that he needs to get a cheap case so he can adhere it to the mount.
Nice craftsmanship ^_^
Sent from my Kangadore 64
mr mystery said:
Can we get a pic with the phone attached?
Click to expand...
Click to collapse
Using an ultrathin 3mm case and double sided tape. I dont recommend this case for this job as its super hard to remove the phone from it.. A softer flexable TPU case is best.
Sorry for the bad photo, using my Nexus 7 for a camera blows.
The last 3 photos from my Note 1. Anyways the finished product. Enjoy.
What about modifing this car mount to clip in and out?
Sent from my SCH-I605 using Tapatalk 2
Dakota0206 said:
What about modifing this car mount to clip in and out?
View attachment 1572530
Sent from my SCH-I605 using Tapatalk 2
Click to expand...
Click to collapse
looks good but likely cost way more than its worth. may as well just spend the $20 for an original one. you'd still have to make a clip on part and bond it to that mount.
Good job buddy. And here I am, thinking about spending the $25 bucks to get this item n' all.
See this one
Such wow, reviving a very old thread.
My next target controller will be the Dualshock 3.