Database Develop

Need Suggestion on Repair

I have a 6 or 7 month old Kaiser branded by AT&T. I got seperated from it late last week, so it ran it battery down till failure. When I went to recharge the phone, it started attempting to boot, staying at the AT&T globe screen and then appearing to boot again, (black screen and momentary vibrate.) With a bit of searching I found the suggestion of boot to loading screen and leave it there to charge. After 6 hours, the battery has a measured voltage of 4.17V so that should be enough, but the phone continues the booting loop.
I tried hard resetting with the two keys and stylus. The phone acted like a normal hard reset with the questions, but when it tried to boot, it continued the reboot loop.
My question, do you think I should attempt to reload the stock AT&T ROM?
I'm new at this so there's a large learning curve. If you guys think this is a low probably solution, then I'll sent it back / buy another one and save the long learning curve. I use this for business so I could spead the learning curve time writing software I get paid for writing.
Thanks,
Bernie

your phone got damaged from battery drain? is that possible?
i think your phone has another problem... i really dont think the battery drain was the reason...
can you go to bootloader if so try flashing new ROM (you will loose data) but again you said you have performed hard reset (partial HR) so your phone is clean!
if you want send your phone back - yes you need to get stocked ROM and stocked SPL back
BernieHunt said:
I have a 6 or 7 month old Kaiser branded by AT&T. I got seperated from it late last week, so it ran it battery down till failure. When I went to recharge the phone, it started attempting to boot, staying at the AT&T globe screen and then appearing to boot again, (black screen and momentary vibrate.) With a bit of searching I found the suggestion of boot to loading screen and leave it there to charge. After 6 hours, the battery has a measured voltage of 4.17V so that should be enough, but the phone continues the booting loop.
I tried hard resetting with the two keys and stylus. The phone acted like a normal hard reset with the questions, but when it tried to boot, it continued the reboot loop.
My question, do you think I should attempt to reload the stock AT&T ROM?
I'm new at this so there's a large learning curve. If you guys think this is a low probably solution, then I'll sent it back / buy another one and save the long learning curve. I use this for business so I could spead the learning curve time writing software I get paid for writing.
Thanks,
Bernie
Click to expand...
Click to collapse

If you already have Hard-SPL installed and it is a version capable, you may try to put the Rom with a Radio onto the Micro-SD card and re-flash the phone that way. I had an issue where i got a boot loop and it turned out that flashing the radio fixed the issue. I hope you at least had a current backup prior to the hard reset because as of now, there is no way to retrieve it

No worries on the backup, it's backed up daily and I only use it as a data carrier. The only drag of the reset is the time of reloading apps.
I agree it may be more than just software issue due to dead battery, but I have to try everything I can. I've back on my old Moto smart phone and it's just not the same, hahahaha.
Now back to studying Kaiser ROMs and how to.
Bernie

As a follow up for anyone who runs across this in the future. I flashed the original AT&T rom and the problem still exists. I spoke to tech support yesterday and they are mailing out a new/reman replacement. So the problem appears to be terminal.
Thanks guys for trying to help.
Bernie

Touchscreen broke, way to bypass welcome screen?

Hey all, I've been looking around the past few days and didn't see anything on this particular issue.
Basically, I washed my G1 and had to get a new one. The one that got washed has been starting up (slowly, and not always), but the touchscreen no longer works. I reflashed the software to hopefully alleviate any of the problems when it was starting up. My initial thought was to use fastboot to flash the backup I made on my new phone with nandroid, but the bootloader isn't working properly (I'll try a reflash of that too).
So, do any of you guys know of any other ways to bypass the startup welcome touchscreen?

Try placing your finger on the Android, press the trackball, then lift the finger and press the trackball again
Tommy

IzzeLing said:
Hey all, I've been looking around the past few days and didn't see anything on this particular issue.
Basically, I washed my G1 and had to get a new one. The one that got washed has been starting up (slowly, and not always), but the touchscreen no longer works. I reflashed the software to hopefully alleviate any of the problems when it was starting up. My initial thought was to use fastboot to flash the backup I made on my new phone with nandroid, but the bootloader isn't working properly (I'll try a reflash of that too).
So, do any of you guys know of any other ways to bypass the startup welcome touchscreen?
Click to expand...
Click to collapse
Flash the ADP1 software.
Edit: You'd still need touch for that, sorry.

The driver was all wonky, uninstalled, reinstalled, fastboot works now Flashed over to my new G1's state, but forgot to take off the lock screen... Flashing yet again. Everything should be good from here.
Edit: Alright, washing the G1 makes it wacky. The touchscreen works now after restoring it to the new G1's state. Weeeirrrdd.
Edit 2: Anddd now the touchscreen doesn't work :S

well.. when my touchscreen broke i used remote control software to control my ppc from pc .. thats one way to bypass welcome screen, but won't get you much further. I used it for making a backup from my phone.

just leave it off for a while and keep it someplace dry and warm so it can dry out.

You may try to modify build.prop in the rom you flash
ro.setupwizard.mode=DISABLED
I think it will skip the setup

Sorry can't help myself. In the laundry?
I guess I'm wondering what exactly you did. I'm assuming it didn't make it into the dryer....
If you need the data off it, you might be able to ADB pull what you want to keep. If I'm not mistaken, ADB is as close as we have to remote controlling for Android at the moment.
There may be some places around, like PPC Techs, that can do hardware repair. I'm guessing what will happen is you'll occaisionally get it to work for brief stints after reflashing or whatever, but it'll keep conking out until the hardware issue goes away/gets fixed. Hardware issues do that, printers, routers, sometimes PCs.
Not to be a naysayer, but I don't think changing out the software is going to help.

I washed my G1 (was in pocket of jeans under the water for about 90 seconds), and after that I disassembled it to let it dry. It was running fine up to the day I SPL bricked it.

Hey.. i split water on my phone.. it couldnt have been that much but the touch screen wasnt working.. thought if i factory reset it, it may started working..
I dont actually understand all the lingo you guys use.. but any ideas on how i can fix it?
J x
oh the main issue is i cant get past the touch android to continue set up... please i just want my android to work!!! J x

I'm having a similar issue... My phone randomly stopped loading android.process.acore and it's messing with my heart. The touch screen doesn't respond but I can use the trackball to navigate, and every acore process force closes instantly upon activation, such as dialer, contacts, music, etc. The wonderfully helpful people at T-Mobile instructed me to do a factory reset on my G1, and it should fix the problem.
New problem: I can't get past the "Touch me, I'm an Android logo" screen. When I click Emergency Dial, it force closes because the acore processes are still messing up. The intention today was to reload the Cupcake SPL and Radios onto the phone. The issue there is that I can't touch the screen to start the USB connection with my computer.
Anyone have any suggestions aside from paying another $130 bucks??

This will do the trick
google androidscreencast it will allow you to contol your G1 via your PC
...let me know if you have resolved android.process.acore im on the same boat and a wipe and flash has yet to solve it...

same boat for me too! wow, this is three, maybe 4 of us currently experiencing same problem!
I love screen cast. Droid explorer is great too, basically a GUI for adb, and has a plugin for screen cast. Too bad you have to be online though, I'd love to use screencast offline!
I'll update if I figure out the error problem!

Well it looks like a complete wipe and a flash back to non root status is whats gonna take to fix the android.process.acore issue. BUT now w/o root, I cant access the G1 via android screen cast...so im totally stuck on the "Touch Android to begin" screen... sucks to be me lol

I think I'm in the same boat. I didn't know about the screencast application before I did a complete wipe to stock. So I'm stuck at the "touch android" as well. This phones pretty much junk to me right now.

I wonder if any of you have tried restoring your latest back up?

Yes, no help, either on the touchscreen, or the incessant errors. I think there must be some code that checks whether the touchscreen works, and sends back an error if it doesn't. I've tried almost every combination of radios and spls mixed with several different cyanogen roms going back to 4.1, both fresh installs and nand restores.
Currently I'm running the latest cyanogen, radio and hard spl. I get errors often, and can't use the phone / dialer at all without force closing. For now texts and google voice work so I have at least some communication. Ironically, I can't even unroot because none of the spls will flash dreaimg.nbh, but that probelm is in my unresponsive bootloader thread.
Sorry to hear about your predicaments allthrottle and r1ch. Strangely you are right where I'm trying to get, I have warranty coverage to fall back on.

G1 screen is dead in portrait mode

Bought the phone off ebay and it worked fine for about a month and today the screen will only work when slid out. If it is slid in place as normal the screen will only show the last thing on there but will not refresh. You have to slide it out partially to get it to respond to anything.
Is this a known issue?

that really weird. Is your phone rooted? If it is try to wipe and flash. If its not rooted do a factory reset to your phone. That might fix it. If it doesnt, then you should get a new phone hahaha OR just root it and it might fix it.

It's rooted but it also does it in recovery as well as booting up. I have talked to HTC and the phone is still under warranty so I am going to ship it off to them.
I guess I have to restore the device to stock now

decepticon said:
It's rooted but it also does it in recovery as well as booting up. I have talked to HTC and the phone is still under warranty so I am going to ship it off to them.
I guess I have to restore the device to stock now
Click to expand...
Click to collapse
decepticon, how easy was it to talk to HTC? I think (and am sure) my GPU/graphic memory area has corruptions and need to get it replaced too. I also bought it off ebay. I assume it was bought after June 2008 since some material was dated that and should be under warranty.

I remember I had a similar issue on a earlier version of Cyanogen (one of the versions before the Google legal scuffle) and a wipe and/or restore to an earlier backup fixed it. This might be a possible cure but again this is just for my instance.

You should try wiping rotation stats while in recovery mode.

Problem with HTC G1 !!!HELP!!!

I have had my G1 for about 6 months. I flashed a custom ROM few months ago, everything has worked fine. Few days ago something weird started happening. The screen will NOT light up when the phone is closed, doesn't matter what buttons I press or what I do, the screen will stay black. The only time the screen turns on is when I open the phone. When the screen is on and the phone is open and I close the phone, the screen will go dark and shut off...
I have tried hard reset that didnt help. Next think i would try is to format the phone and load up new OS.
Before I do that I would like to know if this happened to anyone else. Also I would like to know if this is hardware related or OS related.
Please help me!

Its still in warranty right? flash the stock rom and send it back, tell them you did a hard reset to try and fix it but it didn't work (explains away why your data isn't on the phone)

Sounds like a hardware issue. As Newbie said, reflash the stock ROM, if that doesn't fix it take it back to Tmo (assuming you're on a contract).

New Nexus Not Working

Hello,
I bought a Nexus one and as I don't live in a country that sells it my cousin brought it to me.
The device doesn't work and self Reboots giving me 20 seconds of use.
Tryed working with/without a sim,
Did a Factory Reset,
Formated the Sd-Card on my Pc,
and still in the same spot.
any ideas on what else to try before giving up?
anyone had this problem and fixed it?
My phone is not ROOTed and is on Version 1 of 2.1
didn't have enough time to get other info like Baseband and stuff.
I'm not willing to root the phone.
** If i send it back it will make the phone very expensive as i will have to pay costums fee when they mail it back to me
Thanks in advance!

Sounds like a DOA. Really bad luck.

If you send it back you should not pay duty to get it back usually, unless you live in a very tax hungry country! Between US and CAN you would not get duty.
Beside try speaking with cust support, DOA are usually well handled by company and so far HTC seem to be handling repair quite well as per the few post about broken screen I have seen.
Did you try running the phone WITHOUT an SD card ? good luck!
Krypton1984 said:
Hello,
I bought a Nexus one and as I don't live in a country that sells it my cousin brought it to me.
The device doesn't work and self Reboots giving me 20 seconds of use.
Tryed working with/without a sim,
Did a Factory Reset,
Formated the Sd-Card on my Pc,
and still in the same spot.
any ideas on what else to try before giving up?
anyone had this problem and fixed it?
My phone is not ROOTed and is on Version 1 of 2.1
didn't have enough time to get other info like Baseband and stuff.
I'm not willing to root the phone.
** If i send it back it will make the phone very expensive as i will have to pay costums fee when they mail it back to me
Thanks in advance!
Click to expand...
Click to collapse

If the boots, has never been rooted (boot unlock), no immediate physical damage, and has no signs of liquid damage or tampering (check void sticker).... it's likely just a software issue. Reload original firmware, or load a new firmware... Don't give up, sounds like the phone is still okay.

Was it bnib?

mrbkkt1 said:
Was it bnib?
Click to expand...
Click to collapse
So it seems.
Where are you from, Krypton1984 ?

Looks like some rogue app is loading at boot, causing reset. Possibly corrupt ROM image - but not sure. Might be software, might be hardware. But here's one thing to try:
If you're on a T-Mobile-compatible phone (900/1700/2100), do yourself a favor and flash stock Froyo. No need to root for that. The guide is in the sticky thread. In case of corrupted ROM image it'll do the trick.

I think you should factory reset it. Maybe even download the official 2.1 rom and install it. See if it fixes it.

Try a battery trade in first. Believe it or not, my first N1 seemed dead, and support gave me a swap for a new unit. When the new unit came in, it was still "dead" with the battery that originally shipped with the device. A new battery is what caused my N1 to finally come to life. The batteries that ship with N1's have QC issues, because I was one of many to report a DOA battery in the Google support forums.

its brand new,
I didn't pay customs on the way in because my cousin brought it to me, so if i send it back i will and it makes the phone very expensive.
what if when i try to change firmware the phone reboots again without finishing?
i dont want to brick the phone.

Krypton1984 said:
its brand new,
I didn't pay customs on the way in because my cousin brought it to me, so if i send it back i will and it makes the phone very expensive.
what if when i try to change firmware the phone reboots again without finishing?
i dont want to brick the phone.
Click to expand...
Click to collapse
Well booting to the bootloader will answer the hardware software question.
1. Turn off the phone.
2. Now press (and hold) the Trackball and turn on the phone.
Once you're in the loader let it sit for a while. If it stays up it's a software problem and a new ROM should sort it out. If it reboots while in the bootloader it sounds like a DOA phone.
Good luck.

You can also try a full factory reset through the bootloader. Search for the instructions as i do not know them off the top of my head

P00r said:
Between US and CAN you would not get duty.
Click to expand...
Click to collapse
Yeah, North America is all one big happy family. We've got NAFTA and everything now.
OP, I am assuming you've allowed the battery to charge full?

badomen said:
Well booting to the bootloader will answer the hardware software question.
1. Turn off the phone.
2. Now press (and hold) the Trackball and turn on the phone.
Once you're in the loader let it sit for a while. If it stays up it's a software problem and a new ROM should sort it out. If it reboots while in the bootloader it sounds like a DOA phone.
Good luck.
Click to expand...
Click to collapse
i am having a similar issue. The phone reboots randomly and gets stuck at the static X logo screen. i have to remove the battery and let it be aside for at least 10 minutes before i am able to get the phone up and running again.
i tried updating to froyo. it installed but then froze up again on reboot. i did the battery thing and then started it up, went on fine..froyo had been successfully installed, but my random reboot problem STILL DID NOT GO AWAY..
can this be sorted by installing the original rom image?? or do i have to go in for a swap?!?
i don't want to swap coz they send out refurbished devices,,but its the last option...

padhi87 said:
i am having a similar issue. The phone reboots randomly and gets stuck at the static X logo screen. i have to remove the battery and let it be aside for at least 10 minutes before i am able to get the phone up and running again.
i tried updating to froyo. it installed but then froze up again on reboot. i did the battery thing and then started it up, went on fine..froyo had been successfully installed, but my random reboot problem STILL DID NOT GO AWAY..
can this be sorted by installing the original rom image?? or do i have to go in for a swap?!?
i don't want to swap coz they send out refurbished devices,,but its the last option...
Click to expand...
Click to collapse
You'll probably need to swap based on what you're saying. I, though, actually think Refurbished devices are just as good or even better than new. Think about it, if you keep getting dust under the screen maybe a refurbished phone will already have the fix? For that scenario it works out.

padhi87 said:
i am having a similar issue. The phone reboots randomly and gets stuck at the static X logo screen. i have to remove the battery and let it be aside for at least 10 minutes before i am able to get the phone up and running again.
i tried updating to froyo. it installed but then froze up again on reboot. i did the battery thing and then started it up, went on fine..froyo had been successfully installed, but my random reboot problem STILL DID NOT GO AWAY..
can this be sorted by installing the original rom image?? or do i have to go in for a swap?!?
i don't want to swap coz they send out refurbished devices,,but its the last option...
Click to expand...
Click to collapse
I really think this is a bad RAM issue.
I had this happen to my Nexus (ATT). It was prior to flashing froyo. I tried everything, flashing back to stock (including radio), cyan's latest, Paul's (stock) Froyo (with and without radio). Same result. Seemingly random reboots.
I thought initially that it was a software issue - It would not reboot while in fastboot/Amon's Recovery. But having tried every software combination, I've concluded that it MUST be hardware, unless I'm missing something big.
The phone, for the most part, would be fine as long as I DON'T TOUCH IT. It would stay idle for a long period of time (24hrs+), then I would use it Everything from web browsing to downloading apps to making calls, and it would reboot. It's frustrating because it seems that it's rebooting for no reason except that I'm touching it.
Sent in for a replacement, it arrives today. Hopefully it will not suffer this problem.

After talking with HTC they told me i need to swap the phone.
Because i'm out of america i need to send it to someone in the US amd then they send him the new divice after he sends my old one,
I am not satisfide with google's (first guy I talked with) and HTC because none of whome understand the severity and the hard feeling of getting a BRAND NEW IN BOX paper-weight. nothing about we'll compensate you or nada.
For me it tells me the brand is not strong enough to manage an outer state service and i wouldn't recomend them for countries that they don't cell it for.
If you where born in a HTC GOOGLE compatible country enjoy!
As i'm am probably less lucky and still in 2010 nationality counts