Database Develop

Noob help needed: Is phone CID locked or not?

Is my Wizard CID locked or unlocked?.
Here is the phone's details at present after I HardSPL(ed) it.
Wizard Service Tool v4.2.1
01/01/08 ....
-------------------------------------
CPU: Texas Instruments - OMAP850
MODEL: Wizard
IMEI: ?????
=> Bootloaders:
IPL: 2.21.0001 (G4 device)
SPL: 2.21.Olip (G4 device w/ HardSPL)
Built on Aug 26 2007 at 19:41:34
Copyright (c) 2007 Olipro & HTC - Hard-SPL
=> Firmware:
OS: 5.1.xxx (Build 14847.2.0.0)
ROM: 2.21
Registry AKU: .2.0.0
Radio: 02.07.1ò
Protocol: P413.1.03
=>Extended_ROM:
Version: 2.21.4.101
Name: Extended_ROM
Status: hidden
-------------------------------------------
However using the same tool to check the CID status, the results are.
Reading CID block...
Calculating CID block sum...
CID checksum: D1E00472
Decrypted stored sum: A752285F43A26357
Decrypted calcd sum: A752285F43A26357
Key index : 86 - Block index: 13
CIDkey: MODULESN
CID IMEI: ????????
CID: WIZO2B01
Phone is CID LOCKED!
------------------------------
Next using the same tool to SuperCID unlock the results are.
UnlockCID (Super CID)
SPL version is 2.21.Olip
DOC chip is write-protected!!
Downgrade SPL to no higher than 1.06 and
repeat procedure.
Question is, I thought that the HardSPL process, CID-unlocked the phone, why is the tool showing it is locked?.
Thanks for your help in advance.
Cheers

HardSPL isn't CID unlocking; is 'simply' patching a modified SPL (hence the name) to fool the bootloader into allowing flashing any ROM.
When WST checks the CID status it reads the CID block zone (which wasn't touched) thus reporting the REAL CID status

Thanks very much for your reply but on more thing?
Q 1: From the other details I have posted, is the phone WM6 ready?
Q 2:can you advice on any WM6 roms that are G4 safe to use?
I get the following problem error message with each WM6 rom is used to date.
[ERROR 300]"INVALID UPDATE TOOL: This update utility cannot be used for your PDA phone. Please get newer update utility".
I have searched and read many post on this problem in the forum but I am being super cautious, before I attempt anything I am not sure of regarding G4 limitations.
I am sure after I do the first upgrade sucessfully I will become more confident and adventurous.
Sorry forget question 2 I just read that ROM recommendation is not allowed in the forum.
Thanks in advance

whateveryouneed said:
Q 1: From the other details I have posted, is the phone WM6 ready?
Q 2:can you advice on any WM6 roms that are G4 safe to use?
I get the following problem error message with each WM6 rom is used to date.
[ERROR 300]"INVALID UPDATE TOOL: This update utility cannot be used for your PDA phone. Please get newer update utility".
I have searched and read many post on this problem in the forum but I am being super cautious, before I attempt anything I am not sure of regarding G4 limitations.
I am sure after I do the first upgrade sucessfully I will become more confident and adventurous.
Sorry forget question 2 I just read that ROM recommendation is not allowed in the forum.
Thanks in advance
Click to expand...
Click to collapse
The details posted lead me to believe you have a WM5 but can't be sure
As for the update tool you must try to use the ones posted by the cooks of the most recent ROMs
I don't know where you were told the ROM recommendation isn't allowed . What more experienced users say is that there are so many good ones that it gets hard to choose from. My favorites at the moment are the TNT ROMs
cheers

Thanks again. Wiil try TNT route.
I will try the TNT route.
By the way I am presently using WM5. Just wanted to upgrade to WM6 to gain a little speed and newer apps.
Cheers.

M3000 with which the IPL number never changes

Hello,
I have here an spv M3000 with which the IPL number (IPL 2,21) never changes. Also only English ROM's can be installed.
I have already try unlock with Lokiwiz.
It writes also the BIN- Files.
However no german firmware can be still installed.
Possibly one can help me.
Greeting woody

Infos of my Orange M3000
Wizard Service Tool v4.2.1
21/03/08 14:19:18
CPU: Texas Instruments - OMAP850
MODEL: Wizard
IMEI: xxxxxxxxxxxxxxx
=> Bootloaders:
IPL: 2.21 (G3 device)
SPL: 3.08 (G3 device)
Built on Nov 13 2006 at 14:02:18
Copyright (c) 2003 High Tech Computer Corporation
=> Firmware:
OS: 5.1.xxx (Build 14406.1.1.1)
ROM: 5.1
Registry AKU: .1.1.1
Radio: 02.69.11
Protocol: 4.1.13.30
=>Extended_ROM:
Version: Unknown
Name: Extended_ROM
Status: hidden
=> Drives and partitions:
|--Handle--|---Size---|
4ea14ec6 - 10.00M (0xa00000)
ceae9ece - 48.23M (0x303c000)
2fb2bf36 - 51.06M (0x3310000)
afb2bd76 - 2.88M (0x2e0000)
6fb2bd52 - 3.06M (0x30fc00)
=> DOC chip unique ID:
000000004c0c01033433069c0a05061f
Key Index: 93
All Done.
Reading CID block...
Calculating CID block sum...
CID checksum: F552D32C
Decrypted stored sum: 2FD0E07C697553A4
Decrypted calcd sum: 2FD0E07C697553A4
Key index : 93 - Block index: 59
CIDkey: MODULESN
CID IMEI: xxxxxxxxxxxxxx
CID: 11111111 (SuperCID)
Phone is already CID unlocked!
Reading CID block...
Calculating CID block sum...
CID checksum: F552D32C
Decrypted stored sum: 2FD0E07C697553A4
Decrypted calcd sum: 2FD0E07C697553A4
Key index : 93 - Block index: 59
CIDkey: MODULESN
CID IMEI: xxxxxxxxxxxxxxxxxxxxx
SIM lock status: 0000000000000000
Your phone is already SIM unlocked!

Not sure why doesn't change the languaje but most roms doesn't include ipl, spl or extendend rom and probably thats why never changes... about languaje no idea, mine is still cid locked and haven´t tried to change languaje i prefer english (i speak spanish but nobody else uses mi phone so no problem)...

can i updating the IPL and SPL number?
or ist the M3000 bricked?

woody303 said:
can i updating the IPL and SPL number?
or ist the M3000 bricked?
Click to expand...
Click to collapse
'Bricked' means it doesn't even turn on!!
Unless you REALLY REALLY want to have IPL and SPL with same values i don't see why bother changing the bootloaders and since WST managed to get all that info your phone is working perfectly
Even more, as you already have it CID unlocked you can flash any ROM (without IPL/SPL)

i never can flashed the spv m3000 with the ROM_UPDATER 2.00.1 ERROR 300
the M3000 starts only to the bootloader i can flashed with the Wizard_Love_2.26.10.2_WWE_Novii_CF2 but after restar thormat failde M3000 starts to the 3 color mode
When i was made an hardreset but the File format faild.
kann i install via mini sd?
Please help me!
cu woody
the IPL is 2.21 and the SPS is 2.18.0001

Just try again, from bootloader mode you can still upgrade roms with the same program... it recognizes the USB port by itself... well. I tried this when rom upgrade didn´t work and i normally have to use the original rom and later try to change it again...

i need the org. rom for mein device SPV M3000 UK.
can you help me?

Help with upgrading operator unlocked phone to WM6

I have a MDAIII T-mobile hardware with Mr Clean AKU 2.3 T-Mobile UK software.
My boot screen shows:
IPL 2.24
SPL 2.24
GSM 02.25.11
OS 2.24.10.1
It's been a while since last flashed the phone so I may need some help now.
I didn't CID/SIM unlocked the phone but I have received the network unlock code from my operator. I am using other operator's SIM with no problem.
Do I still need to go to 1.xx and CID unlock the phone before upgrading to WM6 or I just need to put 2.26 IPL/SPL ROM to be able to upgrade to WM6. Is there a greater risk of having the phone stucked with network unlocking code required then with the normally locked phone? Will I be able to reuse the unlocking code?

versus said:
I have a MDAIII T-mobile hardware with Mr Clean AKU 2.3 T-Mobile UK software.
My boot screen shows:
IPL 2.24
SPL 2.24
GSM 02.25.11
OS 2.24.10.1
It's been a while since last flashed the phone so I may need some help now.
I didn't CID/SIM unlocked the phone but I have received the network unlock code from my operator. I am using other operator's SIM with no problem.
Do I still need to go to 1.xx and CID unlock the phone before upgrading to WM6 or I just need to put 2.26 IPL/SPL ROM to be able to upgrade to WM6. Is there a greater risk of having the phone stucked with network unlocking code required then with the normally locked phone? Will I be able to reuse the unlocking code?
Click to expand...
Click to collapse
Use WST to check the CID status. If still CID locked then you must downgrade to unlock the CID. Only then you can upgrade to WM6 (but only after upgrading IPL/SPL to 2.xx or higher)

CID Actions - Read CID block
Reading CID block...
Calculating CID block sum...
CID checksum: 86F72916
Decrypted stored sum: DDEDC8054035749B
Decrypted calcd sum: DDEDC8054035749B
Key index : 18 - Block index: 215
CIDkey: MODULESN
CID IMEI: XXXXXXXXXXXXXXXXX
CID: 11111111 (SuperCID)
Phone is already CID unlocked!
SIM UNLOCK
Reading CID block...
Calculating CID block sum...
CID checksum: 86F72916
Decrypted stored sum: DDEDC8054035749B
Decrypted calcd sum: DDEDC8054035749B
Key index : 18 - Block index: 215
CIDkey: MODULESN
CID IMEI: XXXXXXXXXXXXXXXX
SIM lock status: 0100000000000000 LOCKED
Lock #1 in use.
Detecting SPL version...
SPL version: 2.24.0000
DOC chip is write-protected!
Do I need to go back to 1.xx and unlock the sim as well or can I proceed with upgrading to WM6. Do I neeed to upgrade to 2.26 ROM before going to WM6?

versus said:
CID Actions - Read CID block
Reading CID block...
Calculating CID block sum...
CID checksum: 86F72916
Decrypted stored sum: DDEDC8054035749B
Decrypted calcd sum: DDEDC8054035749B
Key index : 18 - Block index: 215
CIDkey: MODULESN
CID IMEI: XXXXXXXXXXXXXXXXX
CID: 11111111 (SuperCID)
Phone is already CID unlocked!
SIM UNLOCK
Reading CID block...
Calculating CID block sum...
CID checksum: 86F72916
Decrypted stored sum: DDEDC8054035749B
Decrypted calcd sum: DDEDC8054035749B
Key index : 18 - Block index: 215
CIDkey: MODULESN
CID IMEI: XXXXXXXXXXXXXXXX
SIM lock status: 0100000000000000 LOCKED
Lock #1 in use.
Detecting SPL version...
SPL version: 2.24.0000
DOC chip is write-protected!
Do I need to go back to 1.xx and unlock the sim as well or can I proceed with upgrading to WM6. Do I neeed to upgrade to 2.26 ROM before going to WM6?
Click to expand...
Click to collapse
Well,you already have a CID unlocked phone,there's no need to downgrade to 1.xx and CID unlock the phone,but as you say you got a network SIM unlock code and can easily use SIM of any other network,then there's also no need to downgrade to 1.xx and SIM unlock the phone,The Sim unlock has got nothing to do with upgrade to wm6,as its only concerned with using different SIM.Secondly you already have !PL/SPL 2.xx,you can upgrade to wm6,although its highly recommended to flash the T-mobile 2.26,as its proved to be a solid base,but you can still upgrade to any wm6 with your present IPL/SPL 2.24.
Cheers!

zabardast_1 said:
Well,you already have a CID unlocked phone,there's no need to downgrade to 1.xx and CID unlock the phone,but as you say you got a network SIM unlock code and can easily use SIM of any other network,then there's also no need to downgrade to 1.xx and SIM unlock the phone,The Sim unlock has got nothing to do with upgrade to wm6,as its only concerned with using different SIM.Secondly you already have !PL/SPL 2.xx,you can upgrade to wm6,although its highly recommended to flash the T-mobile 2.26,as its proved to be a solid base,but you can still upgrade to any wm6 with your present IPL/SPL 2.24.
Cheers!
Click to expand...
Click to collapse
Well said my friend.
Just want to add that with lokiwiz the SIM unlock code can be calculated easily and for free.

mestrini said:
Well said my friend.
Just want to add that with lokiwiz the SIM unlock code can be calculated easily and for free.
Click to expand...
Click to collapse
Thanks ! m8
Have a nice day !

also just for your own info, the phone you have is NOT an MDA III. it is the MDA Vario.

Invalid vender id when flashing to 1.56

Invalid vender id when flashing to 1.56
Hi all,
if you have problem with flashing your HD to rom with 1.56 and communicate INVALID VENDER ID this post is for you.If u have in your HD Olinex HSPL.This is my method for this problem:
1.Return to stock 1.14
2.Flashing old rom RUU_BlackStone_HTC_WWE_EastEurope_1.14.479.3_Radio_52.49a.25.26_1.09.25.14_Ship
after that I always was have this ERROR
but there is method:
3.Use USPL 2.5
4.Flash official rom 1.56
Then you can flash duttys rom 2.7
For me this working
Regards

[Q] CID Problem

I have HTC Wizard AKA WIZA200
ROM 2.17.7.2 WWE original, not branded
Radio 02.07.10
IPL/SPL 2.17
and I can't unlock CID.
aWizard shows error
WST say's: SPL version is 2.17.0000
DOC chip is write-protected!!
I thought that I have G4, but hard_SPL says it's G3
I must update ROM cause my Wizard is horrible slow, but how to unlock CID ?