I've got the N1 for a few days , but there's a problem when i pair the N1 with the Parrot 3200LS carkit.
When the N1 call's out then the audio is still on the phone and not on the parrot.
When i push the bluetooth button (in the caller screen ) sometimes de voice from the other side goes to the parrot but the mic from the parrot isn't working so when is speak to the other side the don't understand me because it's verry low.
When i look in the settings from bluetooth and the parrot carkit is says that the profile is : sound from the N1 (or something that way)
Is there maybe a workaround to fix this ?
Have you tried to flash the Parrot 3200 with the latest firmware. All I done with mine was to delete all previous connections (through the Parrot) and just went through the normal settings of pairing a new phone, didn't need to change any settings on Nexus at all.
Out of curiosity, did you add Parrot to paired devices on Nexus, as I made a mistake when I first got the car kit by accepting the Car Kit instead of Parrot.
Related
Hi there,
FIRST POST so go easy on me.....
I have a headset installed in my motorcycle helmet that has been working OK (via Bluetooth) with my previous mobile (Nokia E70). I could take calls as well as listen to music on the headset.
I recently upgraded to the Kaiser phone and tried to pair it with the headset last night. After recognising it it presented me with a "Set as Hands-free" checkbox (which I selected). The "Set As Wireless Stereo" option was not presented (it is greyed out)... and, I guess, as a result, I cannot listen to my music files (or the GPS instructions) through the headset.
Any ideas would be very welcome. The phone functions work fine - I can make and receive phone calls without problems.....
regards
alexis
A2DP - Old bluetooth
Alexis,
I have the same problem. I do not have a helmet, but a carkit.
My carkit does not support A2DP. I think your helmet does not, also.
You need A2DP for this option.
But... There was a cab-file for the Hermes. I installed it, but that even does not work. I will start a new thread with a question about this.
Temba
Since I upgraded my breeze to WM6 my handsfree bluetooth has not been working right. I have a JVC KD-BT1 bluetooth carradio/headset
I can pair with it and I see battery status, antenna signal and even the phonebook. When a call comes in, the radio sees it and then it mutes.
But there is no sound (microphone and speaker) on the radio. The microphone and speaker on phone keep working like there is no headset
I looked around and found out that microsoft uses a new bluetoothstack in WM6.
This is not compatible anymore with some headsets.
So there are sometimes these kinds of issues.
The best way to solve this is to get an firmware update of your BT headset.
I also found this alternative:
Change the registry:
HKEY_LOCAL_MACHINE\Software\Microsoft\Bluetooth\Sys\COD
from:
5898764(Decimal) "Telephone (Smartphone)" (default)
to
5374476(Decimal) "Normal phone"
For me, this didn't work, because I couldn't get it to pair with the 5374476 value.
I changed it back and the I could pair fine, sadly with the same result.
Bluetooth problems
I also have some troubles concerning bluetooth and my handsfree kit. I also tried to change the HKEY_LOCAL_MACHINE\Software\Microsoft\Bluetooth\Sys\COD settings but it didn't help.
I cannot make a phonecall using my carkit (Parrot CK3100). It does mute the radio, but the phone conversation is still on the phone.
I have one workaround. .... When I use my GPS receiver and software actively, I CAN make a conversation by using the carkit....strangely.
But then the GPS stops during the conversation.
None of these problems are present when I use WM5, all WM6 and above ROMS have these problems..... Anyone?
Downgrading is not an option to me
Hello all,
Have searched forum but not found exactly my problem.
I'm running ASerg Rus v.24 ROM on my O2 XDA Diamond and I have Parrot CK3000 bluetooth car kit. Gadgets work together flawless as they should unless I use any GPS software. When I'm running any software using GPS (e.g. Navitel Navigator or PocketGForce), on incoming call the carkit rings, but when I push button on carkit to answer, it makes "bleep" sound indicating that it lost connection to Diamond, and the sound goes to handset, not thru carkit. It is obviuos that I can't hear anything and speak to handset pinned to car dashboard. I just have to say aloud to the caller that I have some problems and I will call back in few minutes... It is very annoying that I can't talk while GPS'ing.
Anybody else experienced problems like this? Any solution?
Do you get your sat nav directions through the handsfree when in use? If so how? Usually that means that the Parrot is using A2DP BT profile and not the handsfree profile, but I do not think the CK3000 supports A2DP. Have you tweaked in some way the phone or added an app so that the sat nav uses the handsfree profile? I did using BTMusic app. If you have it may have something to do with the settings on that.
No, navigation software speaks thru phone's loudspeaker, not thru car kit over BT. And PocketGForce I've mentioned above does not speak at all since it is a measurement application using GPS only for getting current speed.
I don't know, maybe I have to play with different radio versions?
I have a stock T-Mobile Vario-3 from first release, no ROM updates, and I have an odd problem when connecting it to my car stereo via Bluetooth. Initially I thought it was a bug with my Pioneer head unit, but I've just got a new car and it's doing the same thing with the Renault factory-fitted unit.
When the (already paired) phone auto-connects via bluetooth, the car stereo reports that it is dialling the last number - although the phone does not actually dial, and the phone itself continues to work normally as if it is not connected.
If I reboot the Vario the problem seems to go away until after I have made another phone call, and then the problem returns again. On the old Pioneer head unit I could just cancel the 'phantom call' by selecting back to the radio or CD input, but on the new Renault the only control keys that work are volume, so I have to disconnect and reset the phone again to get it to connect correctly.
Once I get past this glitch, everything works perfectly - good stereo audio output for my MP3s with playback-control via the car's buttons, hands-free phone use, accessing the phone's Contacts directory via the car controls, etc.
Does anyone else have this problem, or know of a proper fix?
Or maybe someone is telling me that I really do need to get a Touch Pro 2....
Andre
I have a Dension Gateway Five Bluetooth car kit and it is working perfectly with other devices (HTC HD2 Android, HTC Sensation, Samsung S3).
With the RAZR i I can use it to pick up calls just fine but I cannot use the phonebook to dial out. I can also use the phone to dial out just fine.
But when I dial from my car stereo/BT it seems that it does not dial, but when I look in the call history I would see a call with a duration of 0 seconds. So it is dialing.....
I have even completely reset the car kit.
I have seen there is another thread here (http://forum.xda-developers.com/showthread.php?t=2051863) about BT but it seems to be regarding a different issue and I cannot try the tool as I cannot root my device.
Any ideas anyone or same behaviour?
Regards,
KalleH
I have the same issue.
I have a Ford car and I connect my Razr I to my Ford car stereo via bluetooth. Before JB OTA update (I got it last week), Bluetooth was ok : I was able to manage my Razr I from the keypad of the Ford car stereo (dial, answer call, ...)
Since JB update, when I am trying to dial, it does not work if the screen is locked. However, if the screen is unlocked, I am able to use the phone from car stereo.
Even if the setting "Parameters -> Security & screen lock -> Allow Bluetooth bypass" is ON, it does not work ...
I eventually found how to get bluetooth working on my car stereo.
I just delete the pairing (in the car stereo and in the Razr I) and I did a new bluetooth pairing between my car and my Razr I.
All works fine now.