Hi i get one HTC Touch Diamond blocked on XDP Diamond Logo,i try to reset with hard reset but i cant put in reset mode,so have any method to reflash because i'm new with HTC Phone thanks
Your only solution seems to be flash a new rom.
This guide should help you do just that.
Make sure your device is at the bootloader screen and connected to your computer before you run any of the executables. To boot it in the bootloader screen just turn the device on while holding the volume down button. Then enter the usb cable when the word 'Serial' appears on the screen and open the ROMUpdateUtility executable when the word 'USB' replaces 'Serial'.
Goodluck! Make sure to flash the Hard Spl first if you have never flashed a custom from before. There is no need to flash a radio, so you can skip that step if you want.
Goodluck and be very careful!
EDIT: If you have some problems or questions about the process or anything send me a message! Because if you post it here I probably won't see it.
Related
Hi
I have HERA100 which is stuck on start up logo and can not complete booting, for flashing I have to put the phone on boot loader mode, it gives me the following data:
IPL 4.11.0002
SPL 4.11.0000
need advice on which files should be used to revive my phone?
WBR.
enter bootloader(hold camera and poke hole on side)
then get the official ROM(if its a tmobile wing) then flash it.
p.s. i dont think you need the official rom. ive bricked my wing and just reflashed a different ROM
I already tried that, but the upgrade process stops at 2% and the phone reboots with same condition (stuck on start up logo).
By the way, the start up logo is O2 and not Tmobile.
WBR.
hmm are you trying the same rom that bricked your phone?
I tried more than three different roms, most of them stops at 3%, one of them stops at 2%.
is there any special procedure should be done?
WBR
i dont know what else.
try reading this: http://forum.xda-developers.com/showthread.php?t=345411
This happen to me before u have to use the RUU and enter the boot loader through the process u were given in the previous post
your phone is an o2 xda terra. there is no ruu for the terra.
Put your phone in bootloader and use USPL or HardSPL to flash a custom rom to your phone. You will have to HardSPL your phone as it is not yet HardSPL'd if you choose to take that path. In any case, USPL is preferable until you're out of warranty
but the phone can not work in normal mode, how can I use the hardspl or uspl in my case ( phone works only in boot mode)?
for USPL: This will work in bootloader
Download it, put it in the right directory, slap in the .nbh file, FLASH-IFY!
for Hard-SPL: This MIGHT work in bootloader
Download it, press the button
a bit vague, but thats the gist of it. Use USPL
Hello all,
first let me apologize for the long post, and my noobiness. I'm new to the smartphone world, I've sucessfully flashed my Kaiser (from work). Also, I would like to thank everyone who is cooking!
I have the HTC Mteor, which I'm trying to Flash to WM6.1.
When I got it (used), I did a hard reset, and it went back to WM5 in Russian.
I believe I successfully unlocked it, and can now get to the tri-color screen.
It reads:
BBEE100
IPL-0.90
BREE100
SPL-2.05
Every ROM (including the original from HTC) opens, forces the phone to the tri-color screen, and then dies. Error 260, 262, etc.
I've searched the forums, and read that the SPL should be 1.10, but I can't get that to install either.
Any help/suggestions?
Thanks,
Jeff
jjmorris100 said:
Hello all,
first let me apologize for the long post, and my noobiness. I'm new to the smartphone world, I've sucessfully flashed my Kaiser (from work). Also, I would like to thank everyone who is cooking!
I have the HTC Mteor, which I'm trying to Flash to WM6.1.
When I got it (used), I did a hard reset, and it went back to WM5 in Russian.
I believe I successfully unlocked it, and can now get to the tri-color screen.
It reads:
BBEE100
IPL-0.90
BREE100
SPL-2.05
Every ROM (including the original from HTC) opens, forces the phone to the tri-color screen, and then dies. Error 260, 262, etc.
I've searched the forums, and read that the SPL should be 1.10, but I can't get that to install either.
Any help/suggestions?
Thanks,
Jeff
Click to expand...
Click to collapse
install this official rom from HTC
http://rapidshare.com/files/66085556/RUU_BREE100_1.34.261.1_1.38.00.10_HTCRUS_SHIP.exe
Its for RUS QTEK_AO7.
Then you will have SPL 1.10
I have similar problem
I had ROM 6.1 from Futureshock...still problem with radio (my phone couldn´t accessble but signal icon shows good signal, radio version 1.38.0000), so I decided flash some original ROM. Aftet that my booting stuck on HTC logo or Windows Mobile logo. So I can´t use normal way to flashing. Only from SD card or first turn on phone to boot loader mode and than attach usb cable and start flashing. From SD card (where is renamed ROM BREEIMG.NBH) after enter into bootloader mode start loading and than just turn to trhreecolour menu where is BREE100 - IPL-0.90 and BREE100-1.10.0000 and doesn´t want continue. If I flash ROM via USB cable (first go to threecolour mode, than attach cable) than run ROMUpdateUtility.exe and flash process is being started but always die on 2%, than autoreboot and again stuck on HTC logo.
I tried soft reset, I tried lot of ROM versions HTCRUS, HTCEUR, QTEKEUR, FUTURESHOCK but still same problem during flash ROM stop on 2%...
Any ideas how to back life to my MTeoR?
Can I use application like MTTY? Could me help this program?
Thanks for any help...
hi, can any1 send me a link for a ger version of wm6.0pro ?
Wigo said:
I had ROM 6.1 from Futureshock...still problem with radio (my phone couldn´t accessble but signal icon shows good signal, radio version 1.38.0000), so I decided flash some original ROM. Aftet that my booting stuck on HTC logo or Windows Mobile logo. So I can´t use normal way to flashing. Only from SD card or first turn on phone to boot loader mode and than attach usb cable and start flashing. From SD card (where is renamed ROM BREEIMG.NBH) after enter into bootloader mode start loading and than just turn to trhreecolour menu where is BREE100 - IPL-0.90 and BREE100-1.10.0000 and doesn´t want continue. If I flash ROM via USB cable (first go to threecolour mode, than attach cable) than run ROMUpdateUtility.exe and flash process is being started but always die on 2%, than autoreboot and again stuck on HTC logo.
I tried soft reset, I tried lot of ROM versions HTCRUS, HTCEUR, QTEKEUR, FUTURESHOCK but still same problem during flash ROM stop on 2%...
Any ideas how to back life to my MTeoR?
Can I use application like MTTY? Could me help this program?
Thanks for any help...
Click to expand...
Click to collapse
I'm not sure that I understand well, but if you flash from SD, it finish in 100% and than go to three color boot screen? ....
Hi alebo caf Vašek ;-)
My problem is that always stuck on boot image HTC or Windows Mobile blue screen. I can´t use way copy necesseary files to root of phone memmory and than run sspl etc...I have to turn manualy to three-color mode, than connect USB cable and run upgrade utility but still froze instalation on 2%, If I use SD card methode with BREEIMG file uploading doesn´t start....
p.s.: Ak by si mal dáku radu tak možno lepšie vysvetliť po česky ;-). Moje ICQ 208-393-971
Dík
CZ Rom
I would like to install new ROM into my Mteor, but I have no experience doing it. I do not know which version to try, all I need is to be able to enter czech letters on HW keyboard as with original ROM. Any sugestion? I preffer personal answer in czech language ([email protected])
after several times trying to unsuccessfully install a hard spl. (it installs and on reboot keeps the version 3) i upgraded the radio and now its stuck on the htc loadup sreen with the version listed on the bottom . a hard reset just resets so i cant even run the repair utility
one more thing
Oh and one more thing because it wont boot full or go into hard reset mode the computer will not recognize it.
Hello all,
as the title says, one of my touch diamond's is stuck in bootloader screen.
I didnt do anything in between it working and not working, it was on my desk, put it there working, got it 5mins later, and it was in bootloader screen (tricolor screen).
What i've already done to try and fix it:
flash it with the original HTC rom, flash completes succesfully, phone reboots to tricolor screen, so no solution there.
install mtty and format the phone, this completes, reboot the phone, again goes to the bootloader.
reflash the phone with original rom after cleaning it with mtty, flash again completes succesfully but when it reboots after flashing it just goes to bootloader again.
Tried to flash a Hardspl: stuck at 0% and stays there. so that doesnt work.
BUT! when in mtty i give the "boot" command, it DOES start to boot WM. but then again, when i turn the phone of, and on again, or it reboots because of first start after flash, it goes to bootloader again. The VOLDOWN button is NOT stuck, cause when it boots i can use the vol buttons perfectly fine.
Anyone got an suggestion in how to unbrick it? i have a second, perfectly working diamond here too, if that helps in any way.
Some more info ive just seen in mtty, when i told it to boot, it said ONE BAD BLOCK IN CE, remove block ---- to ---- (dont know the exact numbers anymore)
hi..i had something like that...
just download this.
"RUU_Signed_1_93OliNex_HSPL_UnsignedEdition"
it's only 1.7MB and it's will make it work.. atleast it did the job for me...
Hi,
My T mobile touch diamond stuck in bootloader screen? Any experties to help me please.
Thanks in advance.
Hi, I have an htc touch diamond that will not boot past the splash. It turns on, says htc diamond without red letters. I have tried soft reset & hard reset, doesnt work. also phone does not turn on by power button but only the reset button. Every time I try to flash or unlock it says "Error 262", I've tried soft reset and continuing the setup and the error comes up again. I've tried the whole thing of changing the driver from 2007 to 2003 and completed it and still has not fixed error 262. I've tried many different roms and the only ones that bypass 262 are the .exe file rom setups, but after installed still doesnt boot past splash screen. the farthest ive gotten with one .exe is going through the phone setup, but after the setup the phone turns off. the only way my computer notices the phone and the way i flash the phone is when it is in bootloader. have also tried the bootloader where you press the back button. I've been trying so hard to fix this phone but it just wont happen. please help?
ryan21x5 said:
Hi, I have an htc touch diamond that will not boot past the splash. It turns on, says htc diamond without red letters. I have tried soft reset & hard reset, doesnt work. also phone does not turn on by power button but only the reset button. Every time I try to flash or unlock it says "Error 262", I've tried soft reset and continuing the setup and the error comes up again. I've tried the whole thing of changing the driver from 2007 to 2003 and completed it and still has not fixed error 262. I've tried many different roms and the only ones that bypass 262 are the .exe file rom setups, but after installed still doesnt boot past splash screen. the farthest ive gotten with one .exe is going through the phone setup, but after the setup the phone turns off. the only way my computer notices the phone and the way i flash the phone is when it is in bootloader. have also tried the bootloader where you press the back button. I've been trying so hard to fix this phone but it just wont happen. please help?
Click to expand...
Click to collapse
If this happens, you can just soft-reset the device and run RUU again. The update process will then continue.
Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode.
for official rom you can find at http://www.shipped-roms.com/index.php?category=windows mobile&model=Diamond