So I upgraded to the latest mr clean rom and did some tweaks with the registry Wizard. I was playing around with it for a while and turned it off to charge overnight. I wake up and try and turn it on and nothing. I've tried soft reset, and hard reset and it doesn't turn on or do anything. When I plug in my charger the light on my phone doesn't even come on. PLEASE HELP. WHAT CAN I DO!!!.
dew1989 said:
So I upgraded to the latest mr clean rom and did some tweaks with the registry Wizard. I was playing around with it for a while and turned it off to charge overnight. I wake up and try and turn it on and nothing. I've tried soft reset, and hard reset and it doesn't turn on or do anything. When I plug in my charger the light on my phone doesn't even come on. PLEASE HELP. WHAT CAN I DO!!!.
Click to expand...
Click to collapse
It seems that you bricked you phone mate. I think that you installed MrClean rom in a G4 phone so you irrimediably f*cked up the bootloader (IPL and SPL). Many users have reported that their phones were able to boot (and behaved normally) immediatly after the flashing but were dead after they turned them off for the first time, this is what happened to you.
Only thing you can try is going to bootloader mode (but i think it won't work since you messed the bootloader) and then flash a new rom. To do this, press and keep pressed both the keys on the right side and then insert a pin in the reset hole briefly. If the phone goes to the tri-colors screen then you're safe, if not continue reading.
If your warranty perior is not yet over then you can have a new phone for free (DON'T tell them that you flashed an experimental rom!!! Tell only that it went off suddenly or that you were installing an official rom!).
Service centre can repair your device (i suppose they've some method to reflash the bootloader) but i don't know how much they'll ask you.
Try asking other users on this forum. Sorry!
bye
...did you ry to recharge it with the ----ORIGINAL 1A CHARGER----? looks stupid, but i resuscitated mine just before throwing it in the bin. if it works, i will explain you the rest....
yup, I tried charging it with the home charger and still nothing. My battery reads at 3v and it's supposed to be 3.8 so it's not out of juice, but maybe it's just dead?
...you can try with just a normal 9 VDC battery, in order to boost up the voltage, to connect it for a few seconds to the ppc battery till you reach the 3.8 VDC and see if it's working...
Ok, i did that...and amazingly it turned on so I pluged it into the charger right away. Windows booted and about 20sec later the device turned off and won't charge again. So i tried again and the same thing happened. Do I need a new battery? TIA
dew1989 said:
Ok, i did that...and amazingly it turned on so I pluged it into the charger right away. Windows booted and about 20sec later the device turned off and won't charge again. So i tried again and the same thing happened. Do I need a new battery? TIA
Click to expand...
Click to collapse
This is waht you need:
http://www.thetravelinsider.info/phones/cellphonerecharger.htm
This charger is somehow wired weird... it charges the battery AND feeds juice to the phone at the same time (believe it or not, regular chargers and USB cables do not engage until the OS is loaded), allowing you to turn the phone on and in a few minutes plug it into the regular charger to continue charging. Just make sure you get the RAZR tip.
It has saved my ass more than once.
I fixed it , What I did was zap the battery with a 9v battery in 3 sec intervals, I did this about 5 times, then I pluged my phone into the charger and turned it on, the 9v gave it enough juice to boot up and the usb took over from there. So to everyone out there who is having this same problem, try this but don't over zap, check your battery with a multimeter.
im having the same problem----my MDA went dead last night because i forgot to charge the battery and then i went to plug it in the charger but the phone doesnt turn on no more...the light doesnt turn on like if it would be charging and i left it overnight and it still doesnt work..... do yall think that its the battery or is the phone just messed up and cant use it nomore????
Last time I had my battery completely drained, it wouldn't charge from laptop via USB. I read something about how the device's "smart-charging" function itself needs a bit of power to start-up...
but anyways, I couldn't charge the battery through the phone (software charging) - what I had to do was to take a USB cable, cut out one end, identify the +/- (red/black) wires, and charge them directly to the battery's two poles (metal plates). It took about 10-20 seconds of charging until I had enough power in the battery to place it back in the phone, start WM5 and charge it thru the phone.
It would have been much easier if you have a battery charger.
I had my phone connected to the computer through the usb cable, and I just left it connected for a week and it was completely dead and could not be turned on. I don't know how it drained the battery (probally by leaving the wifi on, but the computer was in use all the time). Anyway, thanks to this thread, I used the ac charger and it turned on.
Keywords: t-mobile tmobile mda phone won't don't turn on
phone down
thanks for infos
I'm going to give this a go; a Crossbow ROM flash went horribly wrong last night and in my attempts to repair it (I also must have flashed at least 9 times) the phone went dead. It won't charge either, but battery voltage is 3.7 volts, and I'm sat here wishing it was 3
Will get back to you all!
To update: no... it didn't work! I hooked the battery up to a computer power supply (nearest thing to hand) on 5v and 12v and the voltage increased to about 3.81V... I guess the battery is not the problem with my phone, though the symptoms were the same :-(
Any buttons I can press (i.e. like the voice command button for bootloader) to wake the damned thing up? It's probably fried.
Suggestion
CrArc said:
To update: no... it didn't work! I hooked the battery up to a computer power supply (nearest thing to hand) on 5v and 12v and the voltage increased to about 3.81V... I guess the battery is not the problem with my phone, though the symptoms were the same :-(
Any buttons I can press (i.e. like the voice command button for bootloader) to wake the damned thing up? It's probably fried.
Click to expand...
Click to collapse
My phone has a hardware problem with the on / off button (doesn´t work at all), at the beggining I thought it was a software problem and I tried all sort of tricks, then I gave up and recognized that was a hardware issue and I found 2 ways to turn the phone on 1) When is totally off (This happens when I have to remove the battery to change SIM card) I connect to the USB cable to my PC or to the car or wall charger and I make a soft reset. 2) When I see the phone signal led blinking I remove the memory card and wakes the phone up (not a good idea since I know that the card is going to get damaged sooner or later).
I just got a G3 wizard from a friend a couple days ago. On Thursday I upgraded it to XDA Mobile 6 and left it on the 2.25.11 (I think) T-Mobile Radio that the T-Mobile 2.26 firmware flash put on it. I used it all day on Friday and then I held the power button and shut the phone completely off for 25 hours, but left it plugged in to a usb to 110V AC adapter that came with my Dell Axim X50V. On Saturday night I went to turn it on and it would not come on no matter what I tried. I found this thread and checked the voltage on the battery directly with a multimeter, 3.13V. I cut the head off a usb cable and then held the black and red wires to the positive and negative terminals on the battery for 2 minutes with the head plugged into a front USB port on my PC. The multimeter then read 3.7V. I put it back into the MDA and it turned on, booted and informed me that the battery was completely drained. I plugged it into the USB to AC charger and it read 10% battery on BatteryStatus. I have left it to charge and it is currently at 60%.
I guess the lesson here is to not totally shut the phone off and let it sit, or the battery won't charge, even plugged into my charger. I guess the OS needs to be running in suspend mode for the charging circuit to run. I know I won't turn it all the way off ever again unless I have my little plug thing and my laptop with me.
(old) Nokia phones have a state called "Acting dead" (from service manuals) which takes place when phone is turned off and battery inserted. It means that the energy is flowing around the board so that the responsible hardware keeps waiting for a 'HIGH' signal ordering to turn ON the phone.
When batteries go bellow the 2.x volts they stop being charged by the phones. This is why i protect the battery terminals with tape when the phone is stored for some time and the reason why a lot of people thinks the phones are broken when not used for months. I usually use the 'freezer trick' where i leave the batteries inside the freezer all night and charge them next day.
just 2 cents...
My Wizard XDA got discharged over the weekend and wouldn't start up - after 12 hours on USB it still wouldn't start.
The charge tips saved my bacon - I modified a USB cable as per the instructions above, and used it to charge up the XDA battery - it only needed five seconds and the phone now boots!
Thanks All, great information!
My 2 cents...
If you're going to try the same, connect red usb to the +ve terminal of your battery and black USB to the -ve terminal of the battery. I'd suggest having a voltmeter to hand to check battery and supply voltage.
Disclaimer - the ablve worked for me, but I'm not responsible for anyone damaging themselves, their PC,their phone or anything else by using the above info!
BUMP! thought my phone was dead, hacked a USB cable and i'm back in business!!!!
TYTN II won't turn on
i left it plugged in all day and when i tried to turn it on it didn't respond. i have a second battery that was fully charged and that didn't work either. i tried a hard reset with it unplugged and with it plugged into the charger. nothing works. i'm on the standard at&t rom with lots of programs. i got it unlocked so i can't go to at&t.
Hi,
My kaiser has been running fine, i installed a couple of apps this morning and all of a sudden my battery drained from like 70 - 80 % down to 15 %. even though i have plugged the handset into the charger the battery continues to discharge. I have uninstalled the apps from this morning but i have no power left in my kaiser and awaiting some charge to check if this has made a difference. Does anyone have any ideas?
Thanks
Still no luck after uninstalling some programs. Any advise would be appreciated.
Thanks
Does the phone charge at all? Did the phone ever indicate that it was charging even though it wasn't? When you were attempting to charge it, was it through a wall charger or through the computer? If it was the computer, make sure that "When device is turned on, do not charge the battery when connected to the PC" check box is not checked.
I wouldn't rule it out as a software only issue. If you were doing everything correctly, and it still wasn't charging, then there could be an issue with the charger, the battery, or the usb connector on your phone. I had unknowingly damaged my connecter before, and when I went to charge it, it said it was charging but in reality it wasn't.
Hello there,
Its a but weird but hey this is something very normal for the 2x I think. When I plug in the phone to the pc, this will identify the phone and all that, but it will not charge. I have tried different USB slot and other PCs but nothing happens. On Power the phone will charge as normal. I have also down a calibration of the battery..
Anyone?
I just had the same thing happen to me. I'm glad I read about your wall charger suggestion . Then I read about another person who pulled their battery out and long pressed the power button to clear any risidual charge, I did that and when I turned back on it had gone from 1% to 5%. This was after useing 'battery calibrator' which deletes that file. I also have battery monitor widget and wonder if it conflicts, I think I entered a random number when it asked me the wall chargers ampage. Who knows it charges from computer again. My mother had a problem similar on her nokia, she let the charge get to low and they had to 'shock' the battery into life.
- actually if you have the mode where the screen stays on then the phone might just consume all the power.
-nope, seems wall charger is super fast and computer is slow, maybe usb just doesnt have as many amps
check your usb cable, cheap china cable have problem with charging
I got another cable, GOLD!, and did more testing, its a slow charge on computer and charge goes down when playing counter-strike. Charge goes up on wall socket when playing CS. The charger says it puts out 1A and im sure that more than what my laptop USB puts out, maybe I'll try it with my desktop.. debug mode did nothing to change the effects.
I installed ICS RUU some weeks ago and all has been well.
All of a sudden now when I plug in the wall charger it takes about 30s or so for the charge led to light up or for the phone to indicate that it is being charged. Likewise when the wall charger is unplugged it also takes some time for the charge indicator to go out with the phone still thinking its being charged.
With the USB cable the PC ding dongs immediately but the charge led will take 30s or so before it turns on and I no longer get the prompt for charge only, HTC sync etc.
In all instances the battery does eventually charge fully.
I have rebooted the phone but same problem.
Any ideas what's going on here?
SOLVED.
I removed and refitted the battery. Back to normal.
Thought I would leave the complete post with solution in case someone else experiences the same problem.
i'm having a problem where i put my battery in (think its completely drained)
the light for charging will flash for about 5 sec then go off
try reinserting again. this time it blinks for a bit goes solid then off after a few sec
try one more time this time its solid for about 5 sec then off again. best i can get it to do. if i do this about 10-15 times the screen led light comes on then off and thats it.
any ideas? is there a way to charge it without it in the phone?
@WK - you could try resetting battery stats. I believe that option is available in CWM custom recovery.
I've seen aftermarket batteries and chargers for the Vivid on eBay.
-RKA
Yes there are inexpensive chargers that you can get for these batteries on Ebay. You may even want to get one including a battery.
Having said this have you tried charging using a USB cable from the PC?
You may have a faulty battery or a faulty charger port both of which should be covered by your warranty.
try this too
try plugging the phone in without the battery connected, boot it up that way if it will let you, and then insert the batt while the phone is on..let it charge for a bit.. and see if that helps. Not the safest method, but it almost sounds like you've got the older recovery with the phone off charge issue.
Hope you get it figured out.
EDIT: Don't bother..i just tried it won't boot that way. I was assuming that it might go both ways, bc i know when the phone is on you can pull the batt and as long as its plugged it it stays on.
Hello everybody,
I got my new HTC One just yesterday in the afternoon. I turned it on and battery level was 8%, so I proceeded to charge it while I was doing my initial customizations.
I took it out with me for the evening, when battery level was about 25%. Once I got home, I put it in charge (without switching it off) and went to bed.
This morning battery level was only 37%! Even leaving it in charge, it won't increase... So i went to recovery, did nothing, then did a hard reset and battery level became 63%!!
Now it is stuck at that, even leaving the USB cable for hours.
What can I do??
We need more info please
Are you charging via a mains socket or USB device, if its a USB devise then it may be that it is not supplying enough power
Use the charger and USB lead that came with the phone and power via the mains - its up to 4 hours
Remember it is best not to leave on charge overnight and try not to:
let it go flat
or
fully charge to 100%
I fully charge mine overnight and leave it on, let it die completely and so on. Never affected one phone I have ever owned, including the One.
Or, use the original charger as suggested for now. Let us know what happens when you use the equipment that came with the phone, plugged in to the wall outlet.
Sent from my HTC One using Tapatalk 4