I recently dropped my hd2 and the glass around the lens broke off now the lens is exposed. is there a case that will cover it or a camera lens replacement.
Update: I know im not the only one in America with a glass crack where my lens is and would like to know where to get this fixed or a part site?
I just dropped and broke my camera lens as well today.
mines also cracked after 2 weeks of use....called customer service and they did a manufacturer's warranty and got the replacement right away
Check on eBay - they have direct replacement lenses - OEM. You will have to figure out a way to get some double sided tape to mount it for most of them.
VERY CHEAP - fortunately they are available.
found a replacement on ebay. you dont need to take apart phone or anything. i just super glued around the lens and popped in. good as new.
if $ is not an option look at this...
http://cnn.cn/shop/htc-hd2-oem-housing-set-p-8816.html
They are cheaper on ebay. just ordered one.
Get the Otterbox Defender. I think it is the only case out there truly protecting the camera lens.
i have a cracked camera lens..how do i take it off?
Since it's already cracked, use a knife or something and carefully pry into the cracked area and pull up the cracked glass. Thats how I did it. Just becareful not to push too hard.
is there like walktrhough guide video for this?
Sorry, theres no video or walk through that I know of. As long as you pry off the broken lens its simple from there. Just pry off the lens and then just stick the new one in. Theres not much more than that. You don't have to take the phone apart or anything.
A small sewing needle is a great tool to use. Just pry out the broken piece or you can even do it from the side. What I found when I did it was that there was a ring of adhesive that is difficult to reset correctly once you take the broken lens out. I actually just took the needle and scraped off the adhesive and placed the new lens in so that it's below the surface (beveled, I guess you could say). It stays in just like the old one -- otherwise you'll scratch it the minute you put it down on the table.
charlieb620 said:
found a replacement on ebay. you dont need to take apart phone or anything. i just super glued around the lens and popped in. good as new.
Click to expand...
Click to collapse
What happens if it breaks again now that you used super glue?
...I used some 3M double sided tape and a hole punch. I cut it to size and punched a hole in the middle...carefully cleaned all the old adhesive off and dropped it in. Its not going anywhere and absolutely no dust can get under it...if it breaks again (which it may...so I ordered two because the price was so cheap) it will be much easier to remove than super glue.
Related
Just going to leve everyone know that I ordered a lens from this guy:
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=130438018559&ssPageName=STRK:MEWNX:IT
And fitment was perfect. I took a sewing needle and just pryed out the cracked part. There was a ring of soft adhesive on the inside and I gently pulled it from the old one and pressed the new one right in. Pretty good for less than 3 bucks.
Not that I care though but the new one has a bit smaller hole for the camera and is lighter in color.
I got mine from another seller and it too was a perfect fit. I actually think the lens glass was thicker on the replacement than the OEM one, which to me is a good thing. Super easy fix.
So one week into having my incredible, it drops on the sidewalk (2days before my rugged case came in) and the glass cracked/shattered. the lcd is still completely intact. I was looking at this http://www.amazon.com/gp/product/B00424O7JK/ref=ord_cart_shr?ie=UTF8&m=A3MB8KL7VKZGWY . And was wondering if anyone had any experience with it. I have replaced other screens in other electronic devices, but was looking for any tips specific to the inc or any recommendations on a replacement glass.
I bought mine off ebay and swapped it out. My opinion is to spend the money and buy the whole front housing. Removing the broken glass from the front housing was a MAJOR pain. If you are insistant, make sure you have a good straight razor and flathead screw driver for removing the sticky residue. Head to the local hardware store and get some double-sided tape. If you look in the Epoxy area, i found some double sided rubber material, like what they use for sticking pamphlets together, only a lot stronger. If you dont get it sealed real well, be prepared for lint to get between the screen and LCD. That is the major problem i ahve on mine. Like i said, definitely worth the money to buy the full front housing.
Thanks for the advice. I saw on some videos what a pain it was to get the old glass and adhesive out, but the cheapest I could find the glass with housing already attached was $99 vs $28 for the glass. I wish I would've seen your post prior to ordering. Oh well, we shall see. Thanks also for the advice on the double sided tape. I was looking at it online, but didn't thing to look in just a local harware store for it. I think i'm going to try some medical adhesive remover for the old glue, the only problem is I'm going to have to be really careful around the four buttons on the bottom. It is nice to see that someone has done it successfully though.
You can get the glass and the bezel seperate, but make sure the bezel has adhesive on the entire surface or else you'll get dust in the screen... I fixed mine though and it looks great. Ill post pics later
Hello everyone.
So I noticed some scratches on the glass cover of the camera. I got some replacement glasses, to replace myself. Is there a trick/guide to take off the previous glass, without breaking it?
Some videos say to use a heat gun, but as I understand, the back cover, and even the actual lenses are made of plastic. I'm afraid I'd melt the lenses, and/or make them murky. So I didn't use a heat gun, and I tried using a sharp cutter to pry it open, but it's very hard, as the glass is lower than/flush with the outer ring. I ended up shattering the glass. Luckily, the shards didn't scratch the lenses (as far as I know of). The problem is, the new glass I glued on it got fingerprint on the inside (yeah, human error on my part). Now I have a few other replacement glasses (I bought a few, just in case), but I'm afraid I'd shatter this one again, trying to get it open with a cutter. Does anyone know how to safely take the glass cover off?
Thank you.
creatip said:
Hello everyone.
So I noticed some scratches on the glass cover of the camera. I got some replacement glasses, to replace myself. Is there a trick/guide to take off the previous glass, without breaking it?
Some videos say to use a heat gun, but as I understand, the back cover, and even the actual lenses are made of plastic. I'm afraid I'd melt the lenses, and/or make them murky. So I didn't use a heat gun, and I tried using a sharp cutter to pry it open, but it's very hard, as the glass is lower than/flush with the outer ring. I ended up shattering the glass. Luckily, the shards didn't scratch the lenses (as far as I know of). The problem is, the new glass I glued on it got fingerprint on the inside (yeah, human error on my part). Now I have a few other replacement glasses (I bought a few, just in case), but I'm afraid I'd shatter this one again, trying to get it open with a cutter. Does anyone know how to safely take the glass cover off?
Thank you.
Click to expand...
Click to collapse
If you wanna fix the glass, you can scratch it with an eraser or rub some toothpaste on it.
Do not do this, the text above is meant for comedical purposes only
Edit: rub, not run idot.
I, perhaps foolishly, had a rear camera protector put on my s21 ultra at one of the mobile phone accessory shops, a "no brand" one, then unfortunately I dropped my phone and one part of it cracked, right on top of one of the lenses (but thankfully did its job and protected the lens) so now my photos are blurry. Any tips on how I get the protector off? It seems stuck on very firmly and I'm reluctant to force it. I've since moved states and took it to another phone accessory shop/booth who sell the protectors but they said they don't know how to get them off...
DiveDiva said:
I, perhaps foolishly, had a rear camera protector put on my s21 ultra at one of the mobile phone accessory shops, a "no brand" one, then unfortunately I dropped my phone and one part of it cracked, right on top of one of the lenses (but thankfully did its job and protected the lens) so now my photos are blurry. Any tips on how I get the protector off? It seems stuck on very firmly and I'm reluctant to force it. I've since moved states and took it to another phone accessory shop/booth who sell the protectors but they said they don't know how to get them off...
Click to expand...
Click to collapse
Can you post some pics?
I'd start by using a hair dryer or heat gun to soften the adhesive (as suggested by @[email protected] below) . Then get a plastic spudger and get it's edge between the protector and the camera housing and pry it off slowly. Avoid metal tools as the housing is aluminum and metal can scratch it. If the glue is very strong, use isopropyl alcohol to dissolve/weaken the adhesive (use a syringe or dropper to get very small quantities between the protector and camera housing) and see how it goes.
You could try heating it up a bit to loosen the adhesive.
Is heat a bad idea? Could the heat loosen up some adhesive in the camera or camera lenses that you don't want to be loose?
I'm also in the same boat.
What if you try to slide the protector over to the side?
I'm worried about pulling out one of the lenses if I pull straight off.
KingFatty said:
Is heat a bad idea? Could the heat loosen up some adhesive in the camera or camera lenses that you don't want to be loose?
I'm also in the same boat.
What if you try to slide the protector over to the side?
I'm worried about pulling out one of the lenses if I pull straight off.
Click to expand...
Click to collapse
I don't think a little bit of heat will be a problem. I use a hair dryer on the back of the phone every time i install a skin on my phone (every 2 months or so). Hasn't caused any issue so far. But it's your device, so you have to decide whether it's worth the risk.
Their is an air gap between the protector and the lens covers (those discs of glass that you can touch above the cameras, when there's no covering on the phone), which are recessed in the frame. The screen protector doesn't actually adhere to the lens covers, just the camera housing. I don't see how ripping out the protector will pull on the lens covers.
But like i said above, it's your device so choose whatever method you're comfortable with - as you have to live with the consequences. I'm only saying what i would do with mine if I had the same issue.
DiveDiva said:
I, perhaps foolishly, had a rear camera protector put on my s21 ultra at one of the mobile phone accessory shops, a "no brand" one, then unfortunately I dropped my phone and one part of it cracked, right on top of one of the lenses (but thankfully did its job and protected the lens) so now my photos are blurry. Any tips on how I get the protector off? It seems stuck on very firmly and I'm reluctant to force it. I've since moved states and took it to another phone accessory shop/booth who sell the protectors but they said they don't know how to get them off...
Click to expand...
Click to collapse
Did you end up fixing it, I have the same problem.
KingFatty said:
Is heat a bad idea? Could the heat loosen up some adhesive in the camera or camera lenses that you don't want to be loose?
I'm also in the same boat.
What if you try to slide the protector over to the side?
I'm worried about pulling out one of the lenses if I pull straight off.
Click to expand...
Click to collapse
Did you end up solving this? I have the same issue
YahtzeePog said:
Did you end up solving this? I have the same issue
Click to expand...
Click to collapse
Not yet, been too busy to prep.
But I'm going to try to remove by sliding the protector sideways across the lenses, so there will be a sideways force when the glue hopefully disengages. I'm hoping that's safer than pulling straight up away from the lenses.
enigmaamit said:
Can you post some pics?
I'd start by using a hair dryer or heat gun to soften the adhesive (as suggested by @[email protected] below) . Then get a plastic spudger and get it's edge between the protector and the camera housing and pry it off slowly. Avoid metal tools as the housing is aluminum and metal can scratch it. If the glue is very strong, use isopropyl alcohol to dissolve/weaken the adhesive (use a syringe or dropper to get very small quantities between the protector and camera housing) and see how it goes.
Click to expand...
Click to collapse
I followed these instructions and it worked perfectly! I used a bone folder (bookmaking tool made of bone) to pry up the corner. I guess a credit card would probably also work. Thank you.
The camera lens is cracked. I can buy just the glass or glass and frame (bezel). I have found a video on how to replace just the glass but there isn't any info around on replacing the complete unit. It looks like some heat and a razor might lift it off the back cover, but I dont know if there is any other attachment holding it in place from the inside. Can anyone clarify this for me?
Probably just double sided adhesive tape. Isopropyl alcohol and maybe some heat to lift it if anything is needed at all.
Get the OEM replacement to preserve the optical qualities. Or just buy a rear cover if that's included. The price is usually cheap.
You'll want the pre-cut adhesive mounting if you replace just the glass to preserve it's sealing.