Edit: Whoops! Looks like this belongs in a different forum! My apologies for apparently not doing enough homework!
Hi all, I've looked around online and found no mention of the fact that the 3g/Data settings for those with an iPhone Data plan are different than the standard wap.cingular... So for those of you with iPhone data plans looking to use a different phone, here's some info:
---APN settings for data---
APN: phone
Username:
Password:
---APN settings for MMS---
APN: wap.cingular
Username:
Password:
Server (MMSC): http://mmsc.cingular.com
Proxy: wireless.cingular.com
Proxy port: 80
Update 2010-08-19:
Setup steps for WM 6.1
----------- Connection Setup -----------
From the Start menu select Settings
Go to the Connections tab at the bottom
Tap the Connections icon
In the Advanced tab tap Select Networks
You should be at a page that says Network Management
Under "Programs that automatically connect to the internet should connect using:", tap New
You should see a screen with three tabs: General, Modem, and Proxy Settings
In the General tab enter AT&T MMS for the name of the settings
In the Modem tab, tap New
Enter "iPhone MMS" for the name
Under Select a modem: select Cellular Line (GPRS, 3G)
Hit next
Under Access point name: type in wap.cingular then hit next
Ignore the last page... press finish
In the Proxy Settings tab make sure that This network connects to the Internet is not checked
In the upper right corner of the screen press ok
You should be back at the Network Management page
Tap New again
In the General tab enter AT&T Data for the name of the settings
In the Modem tab, tap New
Enter "iPhone APN" for the name
Under Select a modem: select Cellular Line (GPRS, 3G)
Hit next
Under Access point name: type in phone then hit next
Ignore the last page... press finish
In the Proxy Settings tab make sure that This network connects to the Internet is checked
In the upper right corner of the screen press ok
Press ok again
Press ok a third time
----------- MMS Setup -----------
Now get to the list of your text messages
Hit Menu and select MMS Options
You should now be at a Settings page
Go to the Servers tab
If you already have an AT&T MMS server select that, othewise select New
Under Server Name: type AT&T MMS
Under Gateway: type wireless.cingular.com
Under Port Number: type 80
Under Server address: type http://mmsc.cingular.com
Under Connect Via: select AT&T MMS (this is the name of one of the connections we just set up)
Under Send limit: select 1000K
Press Done
In the upper right corner of the screen press ok
Soft reset for good measure...
Test out your settings! Good luck!
Disclaimer and additional info: I cannot guarantee that these settings and/or this procedure will work for you. All I know is that this works for me. Also, I cannot guarantee that AT&T will not notice that you are not using an iPhone with your iPhone data plan and change your plan and charge you $$$$$. If you bought your phone from AT&T, then they can use your IMEI number to figure out exactly what kind of phone you are currently using. If you didn't buy your phone from AT&T they can still figure out that your phone isn't bought from AT&T. In fact their system does this automatically to display a picture for your phone when you login to your account online. However, to my knowledge (which isn't that good), their system does not automatically change your data plan. If you call AT&T for help with something, you should have an iPhone to make the call with, otherwise the support people can notice. Use all of the above info at your own risk.
what about this?
http://modmyi.com/wiki/index.php/Carrier_APN_Settings#Cingular
aren't these the iphone settings?
Those are not the settings that the iPhone uses. As far as I know, those are the settings that everybody else uses.
Related
I know this has been asked before but 20 min with search and google has only come up with half answers so far.
I was wondering if there was a place that had all of the operator configuration settings. Finding the GPRS t-mobile USA settings are eas, but what about MMS, voicemail (seems not to work with generic world english ROMS), etc?
I have been looking through the ROMs but have found no easy way to rip them out for use with another ROM.
sorry for the probebly stupid post.
Here are some different sets of Settings for TMO USA.
For GPRS/Edge
TMO Simple GPRS:
1. Click on start button, settings, connections
2. Click on the "connections" icon
3. Click on "manage existing connections"
4. Click on "edit" to edit the T-Mobile GPRS entry
5. Click Next to get to the setting called "Access point name"
6. Change this to "internet2.voicestream.com" (you can also try wap.voicestream.com)
7. Click next, then finish (no username and password or domain)
For MMS:
MMS Settings TMO 3 Dec 06
1. Tap Start again.
2. Tap Messaging.
3. Tap Menu.
4. Tap MMS Configuration.
5. Tap the Servers tab.
6. Tap New.
7. Enter "T-Mobile MMS" in the Server Name field.
8. Enter 216.155.165.050 in the Gateway field.
9. Enter 8080 in the Port number field.
10. Enter http://216.155.174.84/servlets/mms in the Server address field.
11. Tap to select "T-Mobile GPRS" from the Connect via drop down list.
12. Tap to select WAP 2.0 from the WAP Version dropdown.
13. Sending Size Limitation: 292K
14. WAP Version: WAP 2.0
15. Click OK
16. Highlight "T-Mobile MMS"
17. Click "Set As Default"
18. Click OK
Note: the previous examples assume you've named the connection T-Mobile GPRS
This worked for me once and than I couldn't get it to work for me again. I also have a .cab file which sets this to work perfectly on the Wizard for TMO USA. I've uploaded to me.
Lot's of people complain on this site that people don't read previous posts. I've read for hours and not found what I need. That's why I'm answering you r post
rambo6 said:
Here are some different sets of Settings for TMO USA.
For GPRS/Edge
TMO Simple GPRS:
1. Click on start button, settings, connections
2. Click on the "connections" icon
3. Click on "manage existing connections"
4. Click on "edit" to edit the T-Mobile GPRS entry
5. Click Next to get to the setting called "Access point name"
6. Change this to "internet2.voicestream.com" (you can also try wap.voicestream.com)
7. Click next, then finish (no username and password or domain)
For MMS:
MMS Settings TMO 3 Dec 06
1. Tap Start again.
2. Tap Messaging.
3. Tap Menu.
4. Tap MMS Configuration.
5. Tap the Servers tab.
6. Tap New.
7. Enter "T-Mobile MMS" in the Server Name field.
8. Enter 216.155.165.050 in the Gateway field.
9. Enter 8080 in the Port number field.
10. Enter http://216.155.174.84/servlets/mms in the Server address field.
11. Tap to select "T-Mobile GPRS" from the Connect via drop down list.
12. Tap to select WAP 2.0 from the WAP Version dropdown.
13. Sending Size Limitation: 292K
14. WAP Version: WAP 2.0
15. Click OK
16. Highlight "T-Mobile MMS"
17. Click "Set As Default"
18. Click OK
Note: the previous examples assume you've named the connection T-Mobile GPRS
This worked for me once and than I couldn't get it to work for me again. I also have a .cab file which sets this to work perfectly on the Wizard for TMO USA. I've uploaded to me.
Lot's of people complain on this site that people don't read previous posts. I've read for hours and not found what I need. That's why I'm answering you r post
Click to expand...
Click to collapse
great write up! but unforunately, i tried it on my 8525 and it didn't work. i'm still not able to get MMS.
i assumed this would work on the 8525 as well.
Wizards are funny that way sometimes things work other they don't, at least that's what I have been able to understand from my experience with mines. About MMS settings I've noticed that if I do a hard reset and mess around with the settings a bit, and leave the MMS settings for latter that no matter how many times I put them in they won't work, now if I do a hard reset and the first thing I do before settings anything else up is do my MMS and my GPRS settings using the exact same settings everything works perfectly, and another thing I usually just punch in the settings myself, I haven't had one of those network settings cab work for me yet. In other words if you've tried everything else and no dice, you might think about doing a hard reset and setting up all these things as soon as you can.
masr1979 said:
Wizards are funny that way sometimes things work other they don't, at least that's what I have been able to understand from my experience with mines. About MMS settings I've noticed that if I do a hard reset and mess around with the settings a bit, and leave the MMS settings for latter that no matter how many times I put them in they won't work, now if I do a hard reset and the first thing I do before settings anything else up is do my MMS and my GPRS settings using the exact same settings everything works perfectly, and another thing I usually just punch in the settings myself, I haven't had one of those network settings cab work for me yet. In other words if you've tried everything else and no dice, you might think about doing a hard reset and setting up all these things as soon as you can.
Click to expand...
Click to collapse
yep thats right, i had to hard reset my 8525 and the .cab worked just perfect... that's weird
TMO USA GPRS Configuration stop working after July 23, 2007
rambo6 said:
Here are some different sets of Settings for TMO USA.
For GPRS/Edge
TMO Simple GPRS:
1. Click on start button, settings, connections
2. Click on the "connections" icon
3. Click on "manage existing connections"
4. Click on "edit" to edit the T-Mobile GPRS entry
5. Click Next to get to the setting called "Access point name"
6. Change this to "internet2.voicestream.com" (you can also try wap.voicestream.com)
7. Click next, then finish (no username and password or domain)
For MMS:
MMS Settings TMO 3 Dec 06
1. Tap Start again.
2. Tap Messaging.
3. Tap Menu.
4. Tap MMS Configuration.
5. Tap the Servers tab.
6. Tap New.
7. Enter "T-Mobile MMS" in the Server Name field.
8. Enter 216.155.165.050 in the Gateway field.
9. Enter 8080 in the Port number field.
10. Enter http://216.155.174.84/servlets/mms in the Server address field.
11. Tap to select "T-Mobile GPRS" from the Connect via drop down list.
12. Tap to select WAP 2.0 from the WAP Version dropdown.
13. Sending Size Limitation: 292K
14. WAP Version: WAP 2.0
15. Click OK
16. Highlight "T-Mobile MMS"
17. Click "Set As Default"
18. Click OK
Click to expand...
Click to collapse
I have used the setup above for years in my 8125.
Unfortunately, after July 23rd, TMO USA updated their system and my GPRS settings stop working for some reason...
Does anybody has the new GPRS configuration for TMO USA?
I struggled with this today as well until I tried Gateway "216.155.165.50" not "216.155.165.050". All is well now.
I Currently have the O2 XDA Mini S (in the UK) and I have in it a Pay and go sim card, O2 have locked the device so that only contract customers can use GPRS and WAP functionality. Is there anyway around this? Will flashing the device resolve my problems?
Many thanks,
Josh.
*edit* I've just successfully flashed and unlocked the device, I was just wondering where I can get the settings I need for pay and go on o2, if not are there any other UK networks that do allow the Wizard to access the Internet on pay and go?
I've found the answer:
How do I manually check / setup the GPRS WAP settings?
Go to [Start]
Tap [Settings]
Tap [Connections]
Tap [Connections]
Under [My Work Network] tap [Manage Existing Connections]. If this is not present tap [Add a new modem connection]
Tap [Edit]
The [Select a Modem] drop-down box should be set to:
XDA Mini S: [Cellular Line (GPRS)]
Tap [Next]
The [Access Point Name] should be set to: wap.o2.co.uk [Post-Pay] payandgo.o2.co.uk [Pre-Pay]
Tap [Next]
The [Username] should be set to: o2wap [Post-Pay] payandgo [Pre-Pay]
The [Password] should be set to: password
Leave [Domain] blank
Tap [Advanced]
On the [TCP/IP] tab, only [Use Server-assigned IP Address] should be selected
Tap the [Servers] tab
Only [Use Server-assigned IP Address] should be selected
Tap [ok]
Tap [Finish]
Tap [Proxy Settings]
Tap [Advanced]
In the [WAP] field enter: 193.113.200.195
In the field to he right of this enter: 9201
In the [HTTP] field enter : 193.113.200.195
In the field to he right of this enter: 8080
Tap [ok] 4 times and exit
To access normal websites wsp:// needs to be placed before the address instead of http://
My final question now is whether there is a way to make it by default put wsp:// before web addresses instead of http://
Ahhh dood,
Thanks loads. I have been trying for AGES to get this wrking on payg
Finally!!
I have one of those Sims where i get free texts and 1MB of internet but never go the internet going but finally i can go on Messenger wherever!
Cheers a bunch!!
thanks!! i have also been trying to get gprs working on my mini s and now i can!!! * goes off to celebrate by not having to trawl around finding open access points to buy stuffies on ebay*
Install my cab on your Shadow
Restart your phone, After Phone boots setup mms by following these directions.
Edit #2
Uploaded new cab that now includes the New MMSC Settings For T-Mobile. So the following List of instructions are no longer needed if you are on t-mobile. I will leave them here just incase. However all that is needed is to run the cab and reboot and then test out mms by sending a picture message to yourself.
Edit #3
Added some original t-mobile rom settings for large mms pictures and movies.
Not needed for the cab. Instructions here for educational reasons.
Setting up the handset
On the handset press Start.
Scroll to and select Settings. Note: you may need to press More to see the Settings icon.
Scroll to and select Connections.
Scroll to and select GPRS.
Press Menu and select Add.
In the Description: field, enter T-Mo MMS.
Scroll to Connects to: and scroll horizontally to WAP Network.
Scroll to Access point: and enter wap.voicestream.com.
Scroll to User name: and leave the field blank.
Scroll to Password: and leave the field blank.
Press Done twice.
Press Menu and select Advanced.
Scroll to WAP connection: and scroll horizontally to Automatic.
Press Done.
Press the end call button.
Press Start.
Scroll to and select Messaging Settings.
Press Menu and select MMSC Settings.
Press Menu and select New.
In the Name: field, enter T-Mo MMS.
Scroll to MMSC URL: and enter http://216.155.174.84/servlets/mms.
Scroll to WAP gateway: and enter 216.155.165.050.
Scroll to Port: and enter 8080.
Scroll to Connect Via: and scroll horizontally to WAP Network.
Scroll to WAP Version: and scroll horizontally to WAP 2.0.
Press Done.
Highlight T-Mo MMS, press Menu and select Set as Default.
Press the end call button to return to the main screen.
The settings have been applied and are ready for use.
Click to expand...
Click to collapse
shadowmike said:
Install my cab on your Shadow
Restart your phone, After Phone boots setup mms by following these directions.
Click to expand...
Click to collapse
This is great ShadowMike. I was trying to set up mms for long time, and u came with that. Thanks man
Thank ND4SPD He sent me the oem folder I just put it into the cab
shadowmike said:
Thank ND4SPD He sent me the oem folder I just put it into the cab
Click to expand...
Click to collapse
I thank him not once for all that great work he did, but certainly thanks you both guys
Thanks a lot
how to danglowd
thank you lots!!
I want to upgrade to wm6.1!!
how to do？？thanks a lot!!
i still cant get or send mms after following your instructions to the dot
I installed the cab and confirmed the settings as shown on the first post. I can send out the pics just under 300k like its supposed to...
but i can't receive any pics?
When i send myself a pic from another phone i see the phone light up for a bit and then nothing..
it supposed to light up then change the icon to E for edge and show me a like inbox icon displaying receiving a MMS but that didn't happen...
anybody have any thoughts?
shadowmike said:
Install my cab on your Shadow
Restart your phone, After Phone boots setup mms by following these directions.
Edit #2
Uploaded new cab that now includes the New MMSC Settings For T-Mobile. So the following List of instructions are no longer needed if you are on t-mobile. I will leave them here just incase. However all that is needed is to run the cab and reboot and then test out mms by sending a picture message to yourself.
Edit #3
Added some original t-mobile rom settings for large mms pictures and movies.
Not needed for the cab. Instructions here for educational reasons.
Click to expand...
Click to collapse
Can you give out what the registry is supposed to look like after your cab is installed?
I still have SampleMMS and no Tmobile MMS and not sure if it makes a difference with my issue.. also most values on send and receive are not at 300k when i look under arcsoft in the registry..
I installed your cab and set up the settings like your post said but I still can't receive mms.
The cab isn't setting up the gprs settings on my phone, am I doing something wrong?
muncheese said:
The cab isn't setting up the gprs settings on my phone, am I doing something wrong?
Click to expand...
Click to collapse
No your not, that is the same issue I am having.. you have to set it up yourself.. with the instructions on the first post..
I haven't been able to receive MMS using that cab but I can send them out up to 300k ...
Yea, ended up doing that.
Likewise, incoming mms aren't coming in. =/
edit: and now I can't send either. oops.
muncheese said:
Yea, ended up doing that.
Likewise, incoming mms aren't coming in. =/
edit: and now I can't send either. oops.
Click to expand...
Click to collapse
install the cab then ensure the GPRS settings are correct.. to test send an MMS to your email.. make a contact title it something like "my email" and put your email and make sure your email is saved as email and not mobile or anything else.. then send a pic to your email. you should be able to send it.. the same would work if you would send it to a differ cell phone..
the only issue here is that the incoming will not work and I'm not sure why..
Turns out it was crappy reception in my shop I can send them. =X
Now it's just the phone mocking me by lighting up when an mms comes in.
muncheese said:
Turns out it was crappy reception in my shop I can send them. =X
Now it's just the phone mocking me by lighting up when an mms comes in.
Click to expand...
Click to collapse
mocking lol yeah mine does this too..
OOPS
shadowmike said:
Install my cab on your Shadow
Restart your phone, After Phone boots setup mms by following these directions.
Edit #2
Uploaded new cab that now includes the New MMSC Settings For T-Mobile. So the following List of instructions are no longer needed if you are on t-mobile. I will leave them here just incase. However all that is needed is to run the cab and reboot and then test out mms by sending a picture message to yourself.
Edit #3
Added some original t-mobile rom settings for large mms pictures and movies.
Not needed for the cab. Instructions here for educational reasons.
Click to expand...
Click to collapse
I instaled the cab and now my MMS is gone.?
I have HTC Juno/Phoebus WM6.1 Clean Developer Edition and have no problems with small images when I receive a picture it is the same size mms and email I made my on mms files with ND4SPD from the oem folder but I tried
shadowmikes new cab and it still works looking at the connects settings I see some differences then my phone here is what I have and the other thing I did is set up windows live on the slide by going in to the reg. and going to
hklm\security\chome\defaultsettings\cwindowslive disabled value 0
hklm\software\microsoft\chome\cwindowslive disabled value 0
now just set it up if this don't help post back i would like to see a fix for this
On the handset press Start.
Scroll to and select Settings. Note: you may need to press More to see the Settings icon.
Scroll to and select Connections.
Scroll to and select GPRS.
Press Menu and select Add.
In the Description: field, enter T-Mobile MMS.
Scroll to Connects to: and scroll horizontally to T-Mobile MMS.
Scroll to Access point: and enter wap.voicestream.com.
Scroll to User name: and leave the field blank.
Scroll to Password: and leave the field blank.
Press Done twice.
Press Menu and select Advanced.
Scroll to WAP connection: and scroll horizontally to Automatic.
Press Done.
Press the end call button.
Press Start.
Scroll to and select Message options.
Press Menu and select MMSC Settings.
Press Menu and select New.
In the Name: field, enter T-Mobile MMS.
Scroll to MMSC URL: and enter http://216.155.174.84/servlets/mms.
Scroll to WAP gateway: and enter 216.155.165.050.
Scroll to Port: and enter 8080.
Scroll to Connect Via: and scroll horizontally to WAP Network.
Scroll to WAP Version: and scroll horizontally to WAP 2.0.
Press Done.
Highlight T-Mobile MMS, press Menu and select Set as Default.
Press the end call button to return to the main screen.
kron2 said:
Scroll to Connects to: and scroll horizontally to T-Mobile MMS.
Click to expand...
Click to collapse
I just did a clean install of the ROM and went ahead and installed the suggested cab..when I got to this step there was no option to select Tmobile MMS??? I thought the default option to select was WAP? in any case it didnt' work
also when you install the mms cab it already puts a t mobile mms settings in the message options..but its flawed because it doesn't let you edit or delete it. you have to select it as default or create a new mms settings under different name and set that to default. i did that with your suggestioned and created new settings with differ name. Event editing the suggested settings from the cab doesn't work because it forces you to save new name and it keeps the same old settings.
I reinstalled shadowmoikes mms cab and tried it with out wifi and had no internet so I had to uninstall it and had internet did you louse it to there has to be a resin my mms works with images the other thing I did is use network wizard but it will set the data to wap. a long with mms
kron2 said:
I reinstalled shadowmoikes mms cab and tried it with out wifi and had no internet so I had to uninstall it and had internet did you louse it to there has to be a resin my mms works with images the other thing I did is use network wizard but it will set the data to wap. a long with mms
Click to expand...
Click to collapse
well the only thing I can get working with it is sending pics out and upon receiving my phone lights up for few seconds and then the light dims back down.. when it lights up the bars do not change to E like it is supposed to to connect to receive the pic.
Do you have the network wizard cab? do you mind posting it here? I have one from another thread but upon instillation no icons show up...
I sincerely appreciate you helping me out.
Chainbolt,
Yes you need the correct connection settings for the Softbank.
Here's the (complex) complete settings - one for MMS+Phone browser, another for Internet access. Call it MMS Settings and Open Settings, and costs are different. It's a bit difficult to explain (Softbank Japanese plans are one of the most complex rate plans in the world), but I'll try.
You SHOULD use MMS Settings for MMS.
You CAN use MMS Settings for the web, but in this case you have to use the proxy in MMS Settings AND you need to set the browser User Agent to one of the Softbank phones available. See below for the list of User Agents. This proxy allows up to 300KB per page.
http://developers.softbankmobile.co..../useragent.php
While you use MMS Settings, you will be charged 0.2yen/packet. You can apply for the Unlimited Packets (Pake-shi-Hoodai in Japanese) Plan for 4410yen per month.
You CAN use Open Settings for the web, this will allow you to use HTTP, HTTPS, ActiveSync and other protocols freely. This settings can also be used from your PC, meaning unlimited Internet Access. You can use any User Agent - so you can use PIE with this connection.
This Open Settings is said to become unavailable from 4/1, as the password is now known to public and Softbank does not want people to use it from the PC.
The cost for using Open Settings is still unclear, but it will be 1029yen - 10290yen per month. Enjoy!
*MMS Settings
[Settings]-[Connections]tab-[Connections]
[Advanced]tab-[Select Networks]button
"connect to the Internet" [New]button
[My ISP name]VFJP Network
[Modem]tab-[New]button
"name of for the connection" Softbank wap
"select a modem" Cellular Line (GPRS, 3G)
[Next]
"Access Point Name" mailwebservice.vodafone.ne.jp
[Next]
"User name" vodafonelive
"Password" qceffknarlurqgbl
"Domain" (blank)
[Finish]
[Proxy Settings]tab
"This network connects to the Internet" Check
"This network uses a proxy server to connect to the Internet" Check
"Proxy server" vfkkwapproxy.vodafone.ne.jp
[Advanced]button
"HTTP Proxy" vfkkwapproxy.vodafone.ne.jp (no change)
"Port" 8080
"User name" vodafonelive
"Password" qceffknarlurqgbl
"Domain" (blank)
Go to Messaging (Outlook E-mail)
[Menu]-[Tools]-[Options]
Click [MMS]-[Servers]tab-[New]button
"Server name" mailwebservice.vodafone.n
"Gateway" vfkkmmsproxy.vodafone.ne.jp
"Port number" 8080
"Server address" http://mms/
"Connect via" VFJP Network
"WAP Version" WAP 2.0
[OK]button
tap [mailwebservice.vodafone.n]-[Set As Default]button
HKEY_LOCAL_MACHINE\SOFTWARE\Arcsoft\Arcsoft MMS UA\Config\mm1\{number}
Name=mailwebservice.vodafone.ne.jp
HKEY_LOCAL_MACHINE\SOFTWARE\Arcsoft\Arcsoft MMS UA\Config\mm1\WspHeader
User-Agent=SoftBank/1.0/705SC/SCJ001
Accept-Language=ja
*Open Settings
[Settings]-[Connections]tab-[Connections]
[Advanced]tab-[Select Networks]button
"connect to the Internet" [My ISP]-[Edit]button
[Modem]tab-[New]button
"name of for the connection" Softbank open
"select a modem" Cellular Line (GPRS, 3G)
[Next]
"Access Point Name" open.softbank.ne.jp
[Next]
"User name" open
"Password" ozRt8n29Ra1Psd07
"Domain" (blank)
[Finish]
[OK]button
yoyo086 said:
Chainbolt,
Yes you need the correct connection settings for the Softbank.
Here's the (complex) complete settings - one for MMS+Phone browser, another for Internet access. Call it MMS Settings and Open Settings, and costs are different. It's a bit difficult to explain (Softbank Japanese plans are one of the most complex rate plans in the world), but I'll try.
You SHOULD use MMS Settings for MMS.
You CAN use MMS Settings for the web, but in this case you have to use the proxy in MMS Settings AND you need to set the browser User Agent to one of the Softbank phones available. See below for the list of User Agents. This proxy allows up to 300KB per page.
http://developers.softbankmobile.co..../useragent.php
While you use MMS Settings, you will be charged 0.2yen/packet. You can apply for the Unlimited Packets (Pake-shi-Hoodai in Japanese) Plan for 4410yen per month.
You CAN use Open Settings for the web, this will allow you to use HTTP, HTTPS, ActiveSync and other protocols freely. This settings can also be used from your PC, meaning unlimited Internet Access. You can use any User Agent - so you can use PIE with this connection.
This Open Settings is said to become unavailable from 4/1, as the password is now known to public and Softbank does not want people to use it from the PC.
The cost for using Open Settings is still unclear, but it will be 1029yen - 10290yen per month. Enjoy!
*MMS Settings
[Settings]-[Connections]tab-[Connections]
[Advanced]tab-[Select Networks]button
"connect to the Internet" [New]button
[My ISP name]VFJP Network
[Modem]tab-[New]button
"name of for the connection" Softbank wap
"select a modem" Cellular Line (GPRS, 3G)
[Next]
"Access Point Name" mailwebservice.vodafone.ne.jp
[Next]
"User name" vodafonelive
"Password" qceffknarlurqgbl
"Domain" (blank)
[Finish]
[Proxy Settings]tab
"This network connects to the Internet" Check
"This network uses a proxy server to connect to the Internet" Check
"Proxy server" vfkkwapproxy.vodafone.ne.jp
[Advanced]button
"HTTP Proxy" vfkkwapproxy.vodafone.ne.jp (no change)
"Port" 8080
"User name" vodafonelive
"Password" qceffknarlurqgbl
"Domain" (blank)
Go to Messaging (Outlook E-mail)
[Menu]-[Tools]-[Options]
Click [MMS]-[Servers]tab-[New]button
"Server name" mailwebservice.vodafone.n
"Gateway" vfkkmmsproxy.vodafone.ne.jp
"Port number" 8080
"Server address" http://mms/
"Connect via" VFJP Network
"WAP Version" WAP 2.0
[OK]button
tap [mailwebservice.vodafone.n]-[Set As Default]button
HKEY_LOCAL_MACHINE\SOFTWARE\Arcsoft\Arcsoft MMS UA\Config\mm1\{number}
Name=mailwebservice.vodafone.ne.jp
HKEY_LOCAL_MACHINE\SOFTWARE\Arcsoft\Arcsoft MMS UA\Config\mm1\WspHeader
User-Agent=SoftBank/1.0/705SC/SCJ001
Accept-Language=ja
*Open Settings
[Settings]-[Connections]tab-[Connections]
[Advanced]tab-[Select Networks]button
"connect to the Internet" [My ISP]-[Edit]button
[Modem]tab-[New]button
"name of for the connection" Softbank open
"select a modem" Cellular Line (GPRS, 3G)
[Next]
"Access Point Name" open.softbank.ne.jp
[Next]
"User name" open
"Password" ozRt8n29Ra1Psd07
"Domain" (blank)
[Finish]
[OK]button
Click to expand...
Click to collapse
Thanks for this. However, it still does not work entirely (although it worked a little!)
Here are my problems:
I changed all the settings for MMS usage as shown below. However, it still does not work entirely.
Sending: First, I tried to send a test message, but it just sits in my email "outbox". The "send/receive" button is gray, so I cannot use that. The system periodically tries to connect to the network to send the message (the icons indicate when it is doing so), but it fails, so it ends up just sitting in my "outbox" with a little clock icon on the side.
Receiving: I keep getting error messages on my phone now (presumeably when I receive a message) that just say "Forbidden". I actually received the headers for five (of a total approximately thirty on the Softbank server) messages, too. However, when I try to download the messages, my phone connects to the network but then nothing happens. I do not get additional error messages. Just nothing happens.
Any suggestions?
Thanks.
somebody could help me about it? Thanks!
Every time, I get a little bit closer! However, I still have a problem.
Now I can:
- Make phone calls.
- Receive phone calls.
- Send SMS messages.
- Receive SMS messages.
- (NEW) Send MMS messages.
However, I still cannot RECEIVE MMS messages. I get an error that says "Cannot decode MMS notification." Additionally, I am able to download the headers for a few (very old) messages (although not for any new messages on the server). However, I cannot download the content of those messages. Do you know how I can try to fix this?
Additionally, when I try to synchronize, I get an error message that says "Cannot copy 'mm1_wsp_wtp_6.log'. Make sure your mobile device has sufficient memory, that the file si not set as read-only, and that you have permission to copy this file type". The device has plenty of available memory. I do not know how to change the readability or copy-ability settings of the file. Any idea how to fix that?
Will kaiser work in Japan? I thought they have completely different networks.,
jldiablo said:
Will kaiser work in Japan? I thought they have completely different networks.,
Click to expand...
Click to collapse
Yes, it could ! i bought a SIM card and put it in Tytn ii,it works well , but i couldn't get the right way to setting MMS ?
TYTN II in Japan
Does anyone know what technology allows the HTC TYTN II to work in Japan. Mine worked very well on the SoftBank system for close to a year. I brought it back to Canada and used it as a skype only phone and when and tried to reconnect in Japan with the same settings as before I did not have any luck. However that's not my point at this time. (TYTN II for sale)
I'm looking for something simple to ebay purchase in NA and bring back with me to Japan and use my SoftBank sim, or what looks like a sim and goes into the sim slot. Phones are hard to buy in Japan without a new contract, not interested in that and they are also registered in wierd and wonderfull ways, apparently to prevent the crime element from using cell phones. I thought Japan did not use GSM technology which I thought was only used with sim cards.
I know my TYTN II quad band phone used the following.
quad-band GSM phone with GPRS, EDGE, UMTS, HSDPA, and HSUPA.
Quad band GSM / GPRS / EDGE (GSM 850, GSM 900, GSM 1800, GSM 1900)
Tri-band UMTS/HSDPA/HSUPA (UMTS 850, UMTS 1900, UMTS 2100)
I know SoftBank uses the following.
SoftBank Mobile currently operates both PDC (Japanese 2G), referred to as "SoftBank 6-2", and W-CDMA (UMTS 3G) networks ("SoftBank 3G"). SoftBank's 3G network is compatible with UMTS and supports transparent global roaming for existing UMTS subscribers from other countries outside Japan. (as per Wikipedia)
The only connection I could see was 3G technology, but I thought that was limited to data use.
If anyone could shed any light on this that would be greatly appreciated.
Regards.
i hard spl'd my phone and now i am unable to send or receive picture messages under mms.....it asks me to download but is unable to download or send after countless tries.....anybody have this problem or know a fix?
Try looking at your other topic.
had similar problem
for me, fix was go to a new mms message, go to the MMS options via the menu, go to servers tab, and take out a "default" server that shouldn't have been there. Setting my t-mobile mms server to default did the trick.
good luck
MystaKlepto said:
i hard spl'd my phone and now i am unable to send or receive picture messages under mms.....it asks me to download but is unable to download or send after countless tries.....anybody have this problem or know a fix?
Click to expand...
Click to collapse
For T-Mobile if you have another carrier let me know
Setting up the data account
On the PDA, tap on Start and then Settings.
Tap on the Connections tab.
Tap on the Connections icon.
Tap on the Advanced tab.
Tap on Select Networks.
Tap on New…
In the Enter a name for these settings: field, enter T-Mo MMS
Tap on the Modem tab.
Tap on New.
In the Enter a name for the connection: field, enter T-Mo MMS
Tap on the Select a modem: drop down list and select Cellular Line (GPRS, 3G).
Tap on Next.
In the Access point name: enter wap.voicestream.com and tap on Next.
In the Username: LEAVE BLANK
In the Password: LEAVE BLANK
Tap on Finish.
Tap on ok three times.
Tap on x to close the settings.
Setting up the MMS account
On the PDA, tap on Start and then Messaging.
Tap on Menu and select Tools then tap Options...
Tap on MMS.
Tap on the Servers tab
Tap on New.
In the Server name: field, enter T-Mo MMS In the Gateway: field, enter 216.155.165.50
In the Port number: field, enter 8080
In the Server address: field, enter [B]http://216.155.174.84/servlets/mms[/B]
Tap on the Connect via: drop down list and select T-Mo MMS
Tap on the WAP Version: drop down list and select WAP 2.0.
Tap on Ok.
Tap on T-Mo MMS and tap on Set As Default.
Tap on ko twice.
Tap on x to close.
The settings have been applied and are ready for use.
mms help plz
i downloaded a new rom to my tmobile wing and it does not gave my the opp too send mms msg...i tryed everything is there a cab. file for it or sumthing plz plz help