Help me, Flash with sd card. - Touch HD Windows Mobile ROM Development

I want to flash my touch hd with my sd card.
give me step to step info.

1: download the ROM to your storage card
2: UNZIP the ROM using the 7zip utility found here
http://www.qweas.com/downloads/syste...ws-mobile.html
3: Rename the unzipped ROM image from ******.nbh to BLACIMG.nbh
4: Move the BLACIMG.nbh file from the folder you unzipped it to accross to the ROOT of the SD Card
5: (This is important) Press and hold the volume DOWN button ONLY, not the up button as if you were hard resetting
6: when you see the 3 colour boot screen it WILL change to a screen asking if you want install the new ROM upgrade, press the power to start the install
7: Finally when finished remove the battery to power the handset down and then reinsert and restart the phone Hard resetting twice before allowing it to boot fully for the first time.
Good Luck

or alternatively read the wiki, forum rules and the stickies at the top of each forum before creating a new thread
Thread closed

Related

How to flash with minisd?

How do i flash a rom onto my p4300??? i dont know how to get into bootloader mode on this device please help me.
flip0406 said:
How do i flash a rom onto my p4300??? i dont know how to get into bootloader mode on this device please help me.
Click to expand...
Click to collapse
bootloader = camera + softreset
and flshing from sd - never worked for me
ok...well can i flash from my usb or whatever???if so do you know where i can get a compatible version for my p4300/wizard.
for those of us with mac's and non windows desktops<it would be nice to have a wayto flash from minisd! I can only remember how easy it was back when I used my zaurus 5500.
Please use the search function because I know 4 sure it is described in these forum, since I have done it myselves.
But once again:
1 BackUp your Herald (if possible)
2 Format your micro-sd card with FAT32
3 Unpack the .nbh file of the Rom you want to use if needed
4 Rename the .nbh file to Heraimg.nbh and place this file, and only this file onto your micro-sd card.
5 Place the micro-sd card in your Herald
6 Put the Herald in bootloader-modus by pressing simultanious camera- and comm. manager button and performing a softreset. Keep pressing both buttons until the bootlaoderscreen appears.
7 Your screen will display the instructions to press the key on the left side of your device (slide the volumebar down)
8 Follow the instructions as displayed.
9 After flashing perform a hard reset as prompted!
10 Tada
But; before flashing by micro-sd:
- Make sure your device is fully charged
- Flashing is always on your own risk and neither I or anyone else can be held responsibl if anything goes wrong
This methode cab also be used when unbricking your device if no pc-connection is possible/available
jappo01 said:
Please use the search function because I know 4 sure it is described in these forum, since I have done it myselves.
But once again:
1 BackUp your Herald (if possible)
2 Format your micro-sd card with FAT32
3 Unpack the .nbh file of the Rom you want to use if needed
4 Rename the .nbh file to Heraimg.nbh and place this file, and only this file onto your micro-sd card.
5 Place the micro-sd card in your Herald
6 Put the Herald in bootloader-modus by pressing simultanious camera- and comm. manager button and performing a softreset. Keep pressing both buttons until the bootlaoderscreen appears.
7 Your screen will display the instructions to press the key on the left side of your device (slide the volumebar down)
8 Follow the instructions as displayed.
9 After flashing perform a hard reset as prompted!
10 Tada
But; before flashing by micro-sd:
- Make sure your device is fully charged
- Flashing is always on your own risk and neither I or anyone else can be held responsibl if anything goes wrong
This methode cab also be used when unbricking your device if no pc-connection is possible/available
Click to expand...
Click to collapse
for me dowsn't wotk!
Errrr..... wrong thread... lol
With some fantasy I interpreted your post as "for me this method did not work"
If it didn't work, you screwed up somewhere...but no need to worry...what exactly didn't work?
In your future post please do not only mention something doesn't work but include which part didn't work and what went wrong.

nbh

hi
i had downloaded marysone 6.5 rom. the file is in nbh format how to update the rom
2255
shameer2255 said:
hi
i had downloaded marysone 6.5 rom. the file is in nbh format how to update the rom
2255
Click to expand...
Click to collapse
There is 2 methods mate:
1. SD Card method
Copy BLACIMG.NBH into the root dir of your Storage Card.
Be sure to have at least 30% of charge.
Turn off your device by using the Power Button.
Go to Boot loader mode. Push and hold Vol. Down + press Power button.
Be sure that Device is connected to PC first before inputting the Storage card
Input Storage card when you see USB displaying on screen.
Now run USPL (If you have aleady run USPL before this or if you have HSPL on device ignore this part).
If all instruction is followed device will start upgrading through Storage Card.
Always ensure that you run USPL before flashing any rom when using USPL method.
2. RUU.exe method
Extract BlackStoneCustomRuu.exe from attached file.
Put BLACIMG.NBH and BlackStoneCustomRuu.exe into same folder on your pc
Be sure to have at least 50% of charge.
Turn off your device by using the Power Button
Go to Boot loader mode. Push and hold Vol. Down + press Power button.
Connect your device to PC
Run BlackStoneCustomRuu.exe and follow the screen instructions.
For noobs to flashing, I'd recommend 2nd method
Hope this helps

Rom update guide, what is missing?

Hi everyone,
I have had this new xperia and love it, I have decided I would like to update my rom but want to make sure I have not missed anything.
If it's not to much to ask can someone let me know if this guide is missing any steps.
my phone and me are both virgins.
Thanks
------------------------------------
Preperation:
1. First lets download all that you will need in order to flash your rom.
Hard_SPL_X1_V1-
And of course download any custom rom made for the X1 of your choice...that is all you will need!
2. Extract the HardSPL somewhere on your pc, you might aswell extract the rom file somewhere on your pc too.
3. Connect your phone via activesync to your pc
4. When you are connected, (I let it finish synchronising one last time, to ensure all of the data on my pc was up to date with the current data on my phone), you then go to where you extracted "X1_HardSPL.exe" and you run it...
5. Follow the instructions at some point it should say something like "Image Version: 1.02.111.7" to "1.00.X1"
When asked, press "Yes" on the X1
6. - Now a Tri-color screen should show up, showing some version Information
After that, a progressbar screen will be shown and the phone will reboot when finished
Click "Finish" on the PC
(To check if you succeeded, turn the device off (long power button press). Then hold the volume down button and turn the device on again, still holding the volume down button until the Tri-color screen shows up. It should read something like:
KOVS110
SPL-0.72.OliNex
MicroP1-787
MicroP2-707)
Remove and reinsert the battery to exit bootloader mode
You completed the first step and are now able to flash any ROM you want to your X1! (Well, at least any ROM made for the X1 of course ;-))
Steps 2-6 need only to be done once...from here on forward should you wish to flash another rom you do not need to install HardSPL again as it is already on your phone.
Flashing your Rom (The fun begins):
7. Rename the rom file you downloaded from whatever.nbh (usually it is ruu_signed.nbh) to Kovsimg.nbh (you can rename it on your pc or on your phone once you have transferred it over)
8. Start up the phone normally, if you have not already done so...then connect it to your pc...(at this point you can connect it without activesync, just as a memory card reader so that you can copy over your rom faster)
Copy your rom into the root of the memory card.
(You can also use any external memory card reader/writer connected to the pc and copy over the file)
Remeber to make sure all files have been deleted off your memory card.
9. Insert the memory card into the phone (You never know somebody might forget to do it :-S )
10. Turn off the phone completely, not standby mode (USB cable must not be attached)
11. Remove and reinsert the battery (This step can be skipped if you made sure you turned off the phone in step 10, this is just in case somebody put the phone in standby instead)
12. Hold down the volume down button and press the power button while still holding both of these buttons until the tri-color screen pops up.
13. Follow the onscreen instructions (It should install the rom +-5mins)
14. When you see the screen say "Succesfully updated", you can then go ahead and remove the battery and reinsert it.
Getting ready to see results (one last step):
Do not skip this step!!! This may result in errors!!!
15. Do a hard reset : Hold down the two silver buttons directly under the screen, while holding them down push the power button, you should then be presented with a screen that asks you to press "R" to reset your device....so go ahead and flip open the keyboard and press "R", when it completes it will ask you to press "Spacebar" to restart the device...go ahead..
16. You are done!
You have now flashed your rom....after it restarts please note the first time it starts up again will take longer than normal, you will be presented with all the normal setup's as you first did when you got your phone...
Like stylus setup and time and date etc...
With this particular rom that I flashed approximately 3/4mins after getting to the today screen a notification came up asking me to choose my operator and it then installed all the necessary connection settings for me....
You may also be asked to restart the device once more after the initial startup of the new rom, this is because upon first start up the rom may install some additional programs / cabs / tweaks which the "cooker" has cooked into the rom....
I cant think of anything more at this point, I tried to be as detailed as possible with this guide and use as much lame-man's terms as possible to make it clear and understandable....
If you have any queries please do not hesitate to post under this thread and I will answer to the best of my knowledge...
Once again thanks to XDA-Developers from whom I have learnt all of the above....
no it looks good you didn't miss anything
commodoor said:
no it looks good you didn't miss anything
Click to expand...
Click to collapse
Thanks,
I have tomorrow off and will be flashing my rom tomorrow.
Now all I need to do is find the rom I want to use.
Is there a guide on all the different roms and what each one does and how it's different?
I know I want winmo 6.5 and htc touch.
hackit said:
Thanks,
I have tomorrow off and will be flashing my rom tomorrow.
Now all I need to do is find the rom I want to use.
Is there a guide on all the different roms and what each one does and how it's different?
I know I want winmo 6.5 and htc touch.
Click to expand...
Click to collapse
Check this: http://forum.xda-developers.com/showthread.php?t=477801
The only way to know which ROM is best for you is to try each of them out and see how it "fits" your personality.
Enjoy flashing!
I have not had time to do the rom flash, and might find a few hours tomorrow.
I have one last question, has any one done flashed a virgin phone in windows 7?
thanks
Need some assistance, I'm at the step where I have copied the rom to my sd card, I have renamed it to Kovsimg.nbh
I hold volume down and power on, i get a message no image file found.
I'm trying to use Jack_3.5b_Full.
I have formated the the flash memory to fat32, the rom is the only file on the card.
I have started the phone and I can see the memory card ok and the flash file.
Does any one have any idea's?
Thanks
hackit said:
Need some assistance, I'm at the step where I have copied the rom to my sd card, I have renamed it to Kovsimg.nbh
I hold volume down and power on, i get a message no image file found.
I'm trying to use Jack_3.5b_Full.
I have formated the the flash memory to fat32, the rom is the only file on the card.
I have started the phone and I can see the memory card ok and the flash file.
Does any one have any idea's?
Thanks
Click to expand...
Click to collapse
Ok I just reformated the sd card and now it's working, go figure.
After a rom update has anyone noticed that the screen flickers on the bottom third?

[GUIDE] The Ultimate Beginner's Guide {Downgrade, Root, Partition, ADB, and MORE!}

The Ultimate Beginner's Guide
NOTE: I am not responsible for any damage that happens to your phone!
NOTE: I am not responsible for any damage that happens to your phone!
NOTE: I am not responsible for any damage that happens to your phone!
NOTE: I am not responsible for any damage that happens to your phone!
Click to expand...
Click to collapse
Rooting your Phone
Q: What is Root?
A: Root is linux operator allowing access to all files in the file system. With root or administrative rights, developers can create or "cook" roms, get access to core files and of course create themes.
For a more detailed explanation go HERE
Q: Why Should I Root My Phone?
A: Here is a couple of reasons:
- A huge preformance boost
- Multi-Touch web browsing
- Install Apps directly to your SD Card
- Wireless and Wired Internet Tethering
- Faster Download Speeds
- Bonus Apps and Widgets from other builds
- Many many many more
Ok, since you kept reading, I think you are ready to root your phone! The only question now is HOW?!?
Check your Phone Version:
1. Go to settings
2. Press on "About Phone"
3. Scroll Down to "Firmware Version" if you have 1.5 please skip to the Rooting Your Phone part of this Guide. If you have 1.6 or higher please follow the downgrading part of the Guide.
-------------------------------------------------------------------------------------------------------------------------------
Downgrading your G1 to Cupcake 1.5
Load the DreaIMG.nbh File
1. Download the Original DreaIMG.nbh file:
Original DREAIMG.nbh
2. Extract the .zip file to get the DreamIMG.nbh file. Place the .nbh file in the root of your sd card. (root = not in any folders)
Note: Make sure your sd card is partition as FAT32 or your phone will not detect the .nbh files.
To Format:
- Load your SD card in the card reader and connect to PC.
- Make sure you back up everything on your card. a format will erase all data on the card.
- Now open “My Computer” and right click on the drive with the SD card (Warning! Make sure its the correct drive).
- Click on Format and select FAT32 on the file system drop down and click then click Start.
- Once completed, Copy your files back to the SD card and make sure the “Original DREAIMG.nbh” is at the topmost folder of your SD card.
3. Turn the phone off if it is on.
4. Turn on the phone by holding the Camera button and the End key until the bootloader screen turns on.
5. Hit the End key to start the update. DO NOT INTERUPT THIS PROCESS.
6. Once it is done, hit the trackball to restart the phone. You now are on the stock firmware RC29. You must do the next section to get back to cupcake.
Get Back to Cupcake
1. Download the cupcake update from HERE
2. Rename the .zip file to update.zip
Note: Make sure its update.zip not update.zip.zip. If you cannot update rename your file to update not update.zip
3. Turn off your phone
4. Hold the HOME key while pressing the POWER key
5. You will see a "!" which means you are in recovery
6. Open your keyboard and type alt+l to see text
7. Type alt+s to updpate
8. Congrats you have now downgraded your phone to the Cupcake 1.5 OS
-------------------------------------------------------------------------------------------------------------------------------
Rooting Your Phone
1. On your phone, Do the following,
- Go to Settings --> Applications
- Make sure Unknown source is checked ON.
THEN,
- Go to Settings --> SD Card and Phone Storage
- Click on Unmount SD Card
- Now Click Format SD Card (Make sure you backed up all your files!)
- It should remount the SD Card for you
2. Go to the Android Market on your phone and Download & Install "Linda File Manager" or "Astro File Manager" if you dont already have a file manager installed.
3. Plug the phone into the compuer via USB, then pull down the notification bar and click on the SD card notification. Then click mount.
4. Download the Following:
FlashRec.apk
Amon Ra’s Recovery Image (12/13/09)
5. Put both files in the root of your sd card (root = not in any folders!)
7. Unplug the phone from the computer once completed
9. Open the file manager and goto SDCard and then find the FlashRec apk file and click it (If asked tell it to use Package Installer to open it. It should automatically install the apk)
10. Open the FlashRec program and click on Backup Recovery Image and wait for it to finish.
11. Once done, click on the empty text box in the FlashRec program and type:
/sdcard/recovery-RA-dream-v1.5.2.img
Then click on the Flash Custom RecoveryImage button and wait for it to finish.
12. Turn off the phone and turn it on into Recovery mode by holding down Home and Power to turn it on (keep holding until the recovery screen comes up has a bunch of text on a black background).
13. Congrats! You have rooted your phone! To keep your root, you MUST continue to the next part of this guide!
-------------------------------------------------------------------------------------------------------------------------------
Installing CyanogenMOD (Custom ROM)
1. While still in recovery scroll down and click on "USB-MS Toggle"
2. Connect your phone to your PC
3. Download the following:
- Latest CyanogenROM HERE (Download should be toward the bottom of the post)
- ADP 1.6 DRC83 Update - HERE
4. Put the .zip files you have now finished downloading in the ROOT of your SD Card (Root = not in any folder)
5. Once done, unplug your phone from your PC
6. Press HOME to disable USB-MS
7. Scroll down to "Flash ZIP from sdcard"
8. Select HTC_ADP_1.6_DRC83_rooted_base.zip and Press HOME to install
9. Once done DO NOT reboot! DO NOT!
10. Scroll down to "Flash ZIP from sdcard"
11. Select update-cm-X.X.X-signed.zip and Press HOME to install
12. Press HOME to install
13. Once Done, press on "Reboot System Now"
NOTE: Reboot will take up to 5-10 min
14. Congrats! You are now DONE!
-------------------------------------------------------------------------------------------------------------------------------
Flash the New RADIO and SPL
Q. Why do i NEED this?
A. This will give your phone more internal memory and is REQUIRED for MOST new roms! This is a requirement for ALL Hero ROMS
NOTE: Please read carefully before flashing! This could BRICK your phone!!!
1. Check if you have a PVT or DVT board
a. Power off your phone and enter bootloader (Camera + Power)
b. Check look at the top and see if it says PVT of DVT
2. If you have a DVT board YOU CANNOT CONTINUE BECUASE THIS WILL BRICK YOUR PHONE!
3. For all you luck PVT board people Download the following:
OTA Radio Update - HERE
Danger SPL - HERE
Latest CyanogenMOD - HERE
4. Rename ota-radio-2_22_19_26I.zip to Radio.zip. Rename spl-signed.zip to SPL.zip. Rename update-cm-4.0.1-signed.zip to ROM.zip
5. Place the 3 renamed files at the ROOT of your SD Card
6. Enter Recovery (Home + Power)
7. Scroll down and press on "Apply any zip from sd"
8. Press on Radio.zip
9. Let it install. Once done it will tell your to reboot to finish the update. Press on Reboot System now in the recovery menu.
10. It will reboot back to recovery. Once it does, Scroll down and press on "Apply any zip from sd"
11. Press on SPL.zip
12. Let it install. Once done it will tell your to reboot to finish the update. Press on Reboot System now in the recovery menu.
13. It will NOT reboot into recovery. Your phone will be stuck on the G1 screen. Once it gets there, reboot your phone by pressing Talk+Menu+Power and then hold the HOME button to enter back into recovery.
14. Scroll down and press on "Apply any zip from sd"
15. Press on ROM.zip and let it install.
16. Reboot your phone to finish.
-------------------------------------------------------------------------------------------------------------------------------
Partition your SD Card to have EXT3 and Swap
Q. What is partitioning?
A. This breaks up your sd card to 3 file systems. Allowing apps to be stored on your SD Card
Q. What is EXT2/3/4?
A. EXT is a filesystem that is only read by a linux OS such as Android. This allows apps to be stored on the SD Card
Q. What is SWAP?
A. Swap is a space on your SD Card that the phone will use as "fake" internal RAM allowing for a major speed increase
1. Backup all your files!
2. Power off your phone
3. Boot into recovery (Hold HOME while holding the POWER button)
4. Scroll down to Partition SD CARD in the recovery menu and press on it
5. Click on Partition SD
6. In the menu, it will ask for you to input two numbers. Swap, then EXT space.
Enter the following:
- SWAP: 96 MB
- EXT: 512 MB
- FAT32: Rest of SD Card
7. Once done go back to the Partition SDcard menu
8 Click on SD:ext2 to ext3
9. Press HOME to confirm
10. Once done, you need to install your current ROM to enable auto apps2sd and swap
11. Download your currently used rom
- Latest CyanogenMOD - HERE
12. Put the .zip file you have now finished downloading in the ROOT of your SD Card (Root = not in any folder)
13. Once done, unplug your phone from your PC
14. Press HOME to disable USB-MS
15. Scroll down to "Flash ZIP from sdcard"
16. Select update-cm-X.X.X-signed.zip and Press HOME to install
17. Press HOME to install
18. Once Done, press on "Reboot System Now"
19. Congrats! You are now done!
-------------------------------------------------------------------------------------------------------------------------------
Installing a Theme
1. Download your favorite theme
- XDA Theme Forum - HERE
NOTE: Make sure you know that the theme is ment for your currently install rom
2. Put the .zip file you have now finished downloading in the ROOT of your SD Card (Root = not in any folder)
3. Once done, unplug your phone from your PC
4. Press HOME to disable USB-MS
5. Scroll down to "Flash ZIP from sdcard"
6. Select "themeExampleX.zip" and Press HOME to install
7. Press HOME to install
8. Once Done, press on "Reboot System Now"
9. Enjoy your newly themed ROM
-------------------------------------------------------------------------------------------------------------------------------
Factory Reset Your Phone (Data + Cache WIPE)
1. Turn off your phone
2. Boot into recovery (Hold HOME while holding the POWER button)
3. Scroll Down to WIPE and click it
4. Click on "Wipe data/factory reset"
5. Press HOME to continue
6. Reboot your phone once done
-------------------------------------------------------------------------------------------------------------------------------
Full SD Card WIPE (EXT, DATA, Dalvik-Cache)
1. Turn off your phone
2. Boot into recovery (Hold HOME while holding the POWER button)
3. Scroll Down to WIPE and click it
4. Click on "Wipe data/factory reset"
5. Press HOME to continue
6. repeat steps 3, 4, and 5 for "WIPE Dalvik-Cache" and "WIPE SD:ext partition"
6. Reboot your phone once done
-------------------------------------------------------------------------------------------------------------------------------
Donate
Hey guys, if you think my Guides have helped you and in general are very helpful, please considering Donating!
Like My Guide(s)? Donate
-------------------------------------------------------------------------------------------------------------------------------
Backup/Restore your phone (Includes EXT Partition)
Backup:
1. Turn off your phone
2. Boot into recovery (Hold HOME while holding the POWER button)
3. Scroll Down to "backup/restore" and click it
4. Click on "Nand + ext backup"
5. Press HOME to continue
6. This will take 5-10 min to finish
Restore:
1. Turn off your phone
2. Boot into recovery (Hold HOME while holding the POWER button)
3. Scroll Down to "backup/restore" and click it
4. Click on "Nand Restore"
5. Press HOME to continue
6. This will take 5-10 min to finish
-------------------------------------------------------------------------------------------------------------------------------
ADB and FASTBOOT
Q. What is ADB?
A. ADB is a source tool for developers and avid android modders such as yourself to access the commands prompt of your phone through your PC. This allows full access to your phone through your computer which makes moving, installing, removing, and replacing files on your phone MUCH faster
Q. What is fastboot?
A. Similar to ADB, this allows you in flash a while img to any partition in your phone, including recovery, system, and user-data.
To setup ADB and Fastboot, please follow my very detailed guide found HERE
-------------------------------------------------------------------------------------------------------------------------------
Difference between a Boot-Loop, Semi-Brick, and a full Brick
Boot-Loop
Q. What is a Boot-Loop?
A. A boot loop is when your phone is stuck on the "ANDROID" screen when u first boot your phone (after the G1 screen or the My Touch screen). This occurs when something you have flashed went bad or interfeared with something you already had installed.
Solution:
1. Turn off your phone
2. Enter Recovery (Hold HOME while holding the POWEr button)
3. Choose from the following:
- Install a rom you KNOW works. Such as the latest cyanogenROM or the rom you have been preivously using
or
- Make a full wipe of your SD Card an phone and flash your update again
Semi-Brick
Q. What is a Semi-Brick?
A. A Semi-Brick is when your phone wont boot at all. The only thing is, you still have access to the recovery and/or fastboot menu
Solution:
1. Turn off your phone
2. Enter Recovery (Hold HOME while holding the POWEr button)
3. Choose from the following:
- Install a rom you KNOW works. Such as the latest cyanogenROM or the rom you have been preivously using
or
- Make a full wipe of your SD Card an phone and flash your update again
Brick
Q. What is a Brick?
A. A Brick is when your phone wont boot at all. This time, you DO NOT have access to the recovery AND fastboot menu. Basically, your phone is a paper weight.
Solution:
You can try this fix here which requires a Donor G1 to work:
HERE
OR
Try to get a new phone.
-------------------------------------------------------------------------------------------------------------------------------
Donate
Hey guys, if you think my Guides have helped you and in general are very helpful, please considering Donating!
Like My Guide(s)? Donate
-------------------------------------------------------------------------------------------------------------------------------
Additions and Questions
- If you think I should add anything to this guide or have any feedback please post it here!
- You can always PM me with questions or even post them here. I would be very glad to help!
-------------------------------------------------------------------------------------------------------------------------------
Credits
- Cyanogen
- Amon_RA
- XDA Community
- Anyone else who i am forgeting
-------------------------------------------------------------------------------------------------------------------------------
saved for future additions
saved for another future posting that i might need
When trying to install the flash rec using linda file manager I don't get the prompt to install. It just tries to open the zip file and show nothing. If I use app installer it doesnt even detect the file. What now?
rpdiddy11 said:
When trying to install the flash rec using linda file manager I don't get the prompt to install. It just tries to open the zip file and show nothing. If I use app installer it doesnt even detect the file. What now?
Click to expand...
Click to collapse
......Android opens .apks, you would need androzip to extract a zip file. Linda will only open .apks to install..
Nicely done, as usual.
Would this guide be the same if I was using Super D as the rom?
hiddengopher said:
Would this guide be the same if I was using Super D as the rom?
Click to expand...
Click to collapse
ya u can use any rom that has root enabled.
rpdiddy11 said:
When trying to install the flash rec using linda file manager I don't get the prompt to install. It just tries to open the zip file and show nothing. If I use app installer it doesnt even detect the file. What now?
Click to expand...
Click to collapse
u need to unzip the file on your computer and only place the .apk files on ur sd card
edit: It doesnt even come in a .zip
Download it here
http://zenthought.org/system/files/asset/2/flashrec-1.1.3-20091107-2.apk
Place on SD and install through linda or any file manager.
Force close
Hey so I did the whole then and it worked mint thank you very much. But one hiccup every time I open something from the original Google install like contacts or market it force closes the app. Any idea on whats going on??
Help please!
why does my G1 get stuck on D" blue android logo? i can't load it. omfg guys please help. I'm in a state of panick here.
I just installed D' latest cm and D' drc83 thingy i just skipped D" upgrade to cupcake part. omg i'm really really panick right now
help please RASAP!
OMG
OMG I"M FINALLY ABLE TO LOAD but why can't i load my 3G settings? D' apn is set by default and all but why can't i use it?
please help me really please
snOwrOse said:
why does my G1 get stuck on D" blue android logo? i can't load it. omfg guys please help. I'm in a state of panick here.
I just installed D' latest cm and D' drc83 thingy i just skipped D" upgrade to cupcake part. omg i'm really really panick right now
help please RASAP!
Click to expand...
Click to collapse
No need to panic. As long as you can access the Blue Android Logo, you are fine.
Please list, step by step, what you did (including ROM Version Numbers).
Also - you might want to try flashing/wiping your phone. That seems to take care of many issues, but I'd still like to see what you did.
elitemonkie said:
Hey so I did the whole then and it worked mint thank you very much. But one hiccup every time I open something from the original Google install like contacts or market it force closes the app. Any idea on whats going on??
Click to expand...
Click to collapse
Best guess would to be to wipe and try again.
a little help!
guys why can't i download apps from market place after following this guide? It keep saying forces close i just can't download any apps at all however i can browse them.
Anywhere to find apk. file apps or any solution please?
Some help here guys!
Thanks! appreciated!
Well I fixed it but I installed Dwangs OS and works mint.
because my Phone had PVT i updated everything... and then i would reboot at the end after installing the ROM and it will not boot... it gets stuck at the T-Mobile G1 Logo... is there anyway to fix this?
Cheers...
ElChibo said:
because my Phone had PVT i updated everything... and then i would reboot at the end after installing the ROM and it will not boot... it gets stuck at the T-Mobile G1 Logo... is there anyway to fix this?
Cheers...
Click to expand...
Click to collapse
Depends, can you get into recovery or bootloader?
JAguirre1231 said:
Depends, can you get into recovery or bootloader?
Click to expand...
Click to collapse
i can get into recovery mode.. i have been trying to reflash.. but no matter what.. i get stuck on The G1 screen...

[TUTORIAL] How to bring ur phone to original state.

[TUTORIAL] How to bring ur phone to original state.
1. Download your stock rom here (Make sure it’s the right provider and language): http://forum.xda-developers.com/showthread.php?t=475482
stockrom: the original rom, made by SE.
2. Extract the file you downloaded from the previous step.
3. Now you have two choices:
1: flash with your micro sd card
2: flash via your computer
4. 1: flash with your micro sd card:
5. Rename the file you extracted to “KOVSimg.nbh” (yeah, change the extension!) Than place the file in root of your micro sd card. Than hold your battery out for 1 second…put it in. Hold ur volume down button and power button on for a while until you are at the bootloader. Wait…. When it asks for it push the power button. And wait for it to finish the flashing. After you finished that hold your battery out and put it back in.
6. 2: flash via your computer:
7. Rename the file you extracted to “ruu_signed.nbh” (yeah, change the extension) put it in the same map as this file (http://www.multiupload.com/LX2ZJKCTQH). Run customRUU.exe. Follow the instructions….
8. Now the original ROM is back on your Phone
9. If you touched the radio than put back the original radio. See: http://forum.xda-developers.com/showthread.php?t=477801
10. When you have the original radio and ROM on ur Phone, it’s time to Make your spl original:
11. Be carefull: always install the radio and the ROM first!!!!!
12. Follow this link: : http://forum.xda-developers.com/showthread.php?t=431218. Download the following files: X1_HardSPL_v1.zip and ruusigned_072stockspl.zip.
13. Extract the First one. run x1_hardspl.exe. extract the next one. Copy it to the map u runned x1_hardspl.exe in and overwrite. Then follow the instructions…
14. Check if you’re done by going to your bootloader again. If it says 0.72.0000 you’re DONE!!
15. If it says olinex ur not doen and have to check this tutorial again…
Good luck!
Very useful... sticky-worthy.
Jezza0 said:
Very useful... sticky-worthy.
Click to expand...
Click to collapse
thank you
benpontiac said:
[TUTORIAL] How to bring ur phone to original state.
1. Download your stock rom here (Make sure it’s the right provider and language): http://forum.xda-developers.com/showthread.php?t=475482
stockrom: the original rom, made by SE.
2. Extract the file you downloaded from the previous step.
3. Now you have two choices:
1: flash with your micro sd card
2: flash via your computer
4. 1: flash with your micro sd card:
5. Rename the file you extracted to “KOVSimg.nbh” (yeah, change the extension!) Than place the file in root of your micro sd card. Than hold your battery out for 1 second…put it in. Hold ur volume down button and power button on for a while until you are at the bootloader. Wait…. When it asks for it push the power button. And wait for it to finish the flashing. After you finished that hold your battery out and put it back in.
6. 2: flash via your computer:
7. Rename the file you extracted to “ruu_signed.nbh” (yeah, change the extension) put it in the same map as this file (http://www.multiupload.com/LX2ZJKCTQH). Run customRUU.exe. Follow the instructions….
8. Now the original ROM is back on your Phone
9. If you touched the radio than put back the original radio. See: http://forum.xda-developers.com/showthread.php?t=477801
10. When you have the original radio and ROM on ur Phone, it’s time to Make your spl original:
11. Be carefull: always install the radio and the ROM first!!!!!
12. Follow this link: : http://forum.xda-developers.com/showthread.php?t=431218. Download the following files: X1_HardSPL_v1.zip and ruusigned_072stockspl.zip.
13. Extract the First one. run x1_hardspl.exe. extract the next one. Copy it to the map u runned x1_hardspl.exe in and overwrite. Then follow the instructions…
14. Check if you’re done by going to your bootloader again. If it says 0.72.0000 you’re DONE!!
15. If it says olinex ur not doen and have to check this tutorial again…
Good luck!
Click to expand...
Click to collapse
Hi Ben,
nice initiative, but the procedure is already in an sticky, and there's even made a movie about it made by biovolt http://forum.xda-developers.com/showthread.php?t=497511
So i'm going to request the mod to close this thread.
Don't get mad about this, but if everyone is going to do this the forum will be loaded by this kind of threads.
But keep up the good work Benpontiac
Indeed.
I will not delete the information, despite it being covered elsewhere. It is clear info and simply laid out. I will close the thread though in order that pre-existing threads are used.
Mike

Categories

Resources