Related
From yesterday onwards i am getting this problem.power button is nt workn as previous.Phone automatically get the signal of long press power button.it means automatically it asks "power will be turned off,and you may lose data if...".and also when i press power button it doesnt goes to standby mode.when i long press the power button sometimes it doesnt switch off..As i think the power button dnt work as normal or may it seems that power button keep pressed internally..pls help me to solve this problem.thnx in advance
some1 pls help me
naheelja said:
some1 pls help me
Click to expand...
Click to collapse
I'd suggest you make a full backup and hard reset the device in order to make sure its not a hardware problem. If it works fine after a hard reset, you'll know its something you installed relatively recently.
I did a hard reset.nothing changed.then i flashed a different ROM.But still i am facing the problem.
Try the following:
Get a can of canned Air and blow it on the button as it might move any debris that are there. Just make sure that the phone is off and the battery is out. KEEP THE AIR STREAM AWAY FROM THE SCREEN! If any of the propellant escapes while you spray, it can freeze the LCD. Just slide it open and stick some paper on top of the screen. Wait a few moments before you switch the device back on
If this doesn't work, flash the Kaiser with its original ROM and SPL just in case there is an odd interaction somewhere. See here: http://forum.xda-developers.com/showthread.php?t=418375
If nothing of the above work, you have two options:
a. If the device is in warranty, return it and get it fixed or replaced. Make sure is has its original ROM/SPL loaded before you do.
b. If the device is out of warranty/you don't care about the warranty, you can try to open it up and see if something is blocking the switch. There are instructions floating around here somewhere.
EDIT: Added warning regarding the propelant and the LCD
Any update here? My tilt is doing the exact same thing
alt236 pretty much said all there was to it. Hard reset, restore stock ROM, try blowing the switch, if all fails send for repair.
Did all of the above and the cost of repair is not worth it. Time to toss my kaiser I guess
Started experiencing a strange issue with my tilt today..
When I soft reset it loads the Today screen, and then attempts to search for the contact 'wszx' (these keys are located next to each other). After this I can navigate the phone just fine using the touch screen, but the only buttons that work are the directional and center buttons located on the front of the phone, and the arrow keys on the keyboard. I cannot type at all using the keyboard, and pressing any of the other buttons does nothing (except the directional/center/Power). I also cannot Hard reset because the two soft-keys do absolutely nothing. I've hard reset in the past but it no longer works.
So am I SOL? I think I've tried everything.. and now I have a custom rom, etc on the phone and I have no way of getting it back to factory rom without the ability to hard reset.
Thanks for any help.
dam1en said:
Started experiencing a strange issue with my tilt today..
When I soft reset it loads the Today screen, and then attempts to search for the contact 'wszx' (these keys are located next to each other). After this I can navigate the phone just fine using the touch screen, but the only buttons that work are the directional and center buttons located on the front of the phone, and the arrow keys on the keyboard. I cannot type at all using the keyboard, and pressing any of the other buttons does nothing (except the directional/center/Power). I also cannot Hard reset because the two soft-keys do absolutely nothing. I've hard reset in the past but it no longer works.
So am I SOL? I think I've tried everything.. and now I have a custom rom, etc on the phone and I have no way of getting it back to factory rom without the ability to hard reset.
Thanks for any help.
Click to expand...
Click to collapse
Sounds like a hardware issue or simply a bad flash. Have you attempted to reflash the rom? Which rom are you using?
Well...
It wasn't working again this morning, but suddenly - out of nowhere - began to work properly. I'm stumped. If I ever figure out the exact issue I'll be sure to post back.
Thanks
Greetings,
I have same problem on my tytn...
Sometimes it suddenly starts working fine, but shortly it breaks again.
I have tried hard-reseting while it was working, but didnt help.
I think the problem appeared after charging my phone with a motorola v3 charger, so maybe it damaged my phone with over-voltage or something...
Anyway, if someone can suggest something i would be very grateful!
Hi I have exactly the same symptoms with my HTC Tytn II...when you power it on it starts typing letters (in my case CEDF). If the recording button is active it will start recording too. This happened suddenly and I haven't used any other charging apart from the usb and wall socket charger supplied with it.
All buttons (except front center key) and keyboard do not work. Any suggestions would be appreciated very much. This phone is only 8 months old.
Hi,
my Kaiser with dutty's WM6.1WWE ROM did the same this morning Yes I disabled the button 6 and stopped the voice recordings but all the hardware keys but few in the center of the keyboard are not responding. So I cant make or receive calls without taking the stylus out and touching the screen soft buttons andd that's pin in the ... while I am driving. I am using this ROM for almost a year now and I am extremely hapy (up to now) with its performance. When it all happened there were no activities on the phone - I woke up from a SMS notification (Yes I did receive an SMS from my bank) followed by repeting Voice Recordings. Any help will be highly appresiated! Thanks in advance!
keyboard problem
I am experiencing a similar problem with my stock tilt my keyboard does work however none of the text appears on the screen. I have tried hard reset and everything else I could think of, short of a clear storage reload. I would appreciate any help or suggestions from some of you more experienced users.
Bisonwill
anyone ever figure this problem out? im having the same thing happen now.
Same here
I've had it for a couple of weeks now.
I'm running WM6.1 from HTC (rom ver.3.29.422.1 from 2009-01-12) so nothing fancy here.
I even ordered and replaced the D-Pad and I replaced the keyboard (just the sticky part though). I totaly dismantled the phone and didn't find any issues with the cables.
Any ideas would be highly appreciated
Join the club!
This is crazy. My problem is exactly the same. I re-romed to the latest phoenix and it did not change a thing.
Help!
help....
any body here found a solution for the keypad/keyboard yet??? i have the same problem as you guys... any idea, thanks so much...
i have the same problem And there is something else. My Kaiser wakes up every 2 minutes - it's killing the battery. It works only for 6 hours now
Help
bump!!!
No more people with this issue or any solutions?
Pls! Help
ive joined the gang!
I decided to flash my cooked rom ive been working on.
i hadnt changed much in the kitchen and i think the flash has went badly.
it starts booting windows and where it should state "calibrate screen" it goes white and hangs there, buttons seem to respond by lighting up when pressed.
Now when i try to get it into bootloader or even hard reset it just doesnt work.
it just restarts the phone.
before this happened the backspace key hasnt been working for ages.
anybody got any ideas??
(lucky for me i have a backup kaiser!)
I'm having the same problem. Automatic wakeup, applications starting automatically, can't use keyboard, have to to use screen to use phone etc. I've hardreset using the clear storage method, reflashed a couple of times, but nothing helped. So here I am joining the club
If it's not a hardware issue, then try to flash another radio, many of the custom ROMs here doesn't include a radio, so if it's caused by a wrong radio, flash a new ROM without a radio doesn't help.
Check the Sticky for 'how to' if not aware.
PS: Check here for something need to know..
The question is.... how do I flash the device if I cant get it to go to boot loader and the OS wont boot properly !?
I think its an official Brick!
the really odd thing I've discovered is sometimes the OS leaves the loading screen on, and when it does if I press the FN and folder key, I get explorer up but its not responding... I haven't tried inserting a memory card yet to see if I can access that.
Danhargreaves said:
The question is.... how do I flash the device if I cant get it to go to boot loader and the OS wont boot properly !?
I think its an official Brick!
the really odd thing I've discovered is sometimes the OS leaves the loading screen on, and when it does if I press the FN and folder key, I get explorer up but its not responding... I haven't tried inserting a memory card yet to see if I can access that.
Click to expand...
Click to collapse
Try this:
1. Take out the battery from the phone.
2. Take out SIM card and SD card.
3. Press in and hold the CAMERA button.
4. Plugin to your computer using the USB cable, while keep holding press in the CAMERA button.
See does it enter the BOOTLOADER mode.
Once entered the BOOTLOADER mode, you can flash a new radio or rom right from there, in your regular way of running KaiserCustomRUU.exe.(Since you already have a HardSPL flashed on, otherwise a HardSPL is needed to flash first.)
Good luck.
Edit: If the power button and the camera button is still working, you can use the regular way of entering BOOTLOADER mode, and flash from bootloader mode or flash from SD card.
Originally posted by Manpreet @ www.sakajati.com
To enter in bootloader mode:
Simply Switch off your phone. Press and hold camera button and also press and hold the power button..You can remove ur finger from power button when phone is switched on but keep holding camera button until u come to bootloader …Now attach the usb to ur computer and do the flashing you normally do.
Click to expand...
Click to collapse
Thx for your suggestion:
I tried removing battery as sim and sd were already removed due to previous attempts in fixing!
so:
i removed battery (did not put back in), plugged in while holding camera
got nothing, so held power button at same time, the green light came on, then went off, and came back on again. but no bootloader.
i tried same procedure with battery in, and all i get is the OS loading up, no bootloader no matter how long i hold the buttons.
is there any other alternative method to get into bootloader (possibly involving other button presses)?
or any other ideas.
Really want to fix this as it was my "experimental" phone for cooking roms with.
Thanks again.
Suspect you have some hardware issue with the camera button. Can you ever take a photo with it?
Edit: Did you read through every post onthis thread:
MTTY (How to fix a bad ROM flash!)
If you tried that and still no luck, you can post your questions there. There are masters will keep an eye on that thread. And generally they only have time to look into their 'subscribed' threads, chances are they will not look into here.
Edit: Maybe the procedure I told is wrong, since I call from memory, check this:
dwny said:
If you have a bad flash....that's no reason to worry.
I haven't had to use MTTY to recover.
In most cases, if there's no issues with the Rom itself...you can pop out the battery and re-flash the same ROM from BootLoader Mode. This will also work if for some reason your computer crashes or loses power & restart during the FLASH.
If the Rom has issues.....the flash will not complete and the device will be stuck in BootLoader Mode. At this point,you must FLASH a FACTORY ROM!!
Pop the battery off 1st, power up the device, device will power up in BootLoader Mode, connect to pc & FLASH your devices FACTORY ROM. This will restore your device back to it's original out the box settings.
The above only works if the device has been put through the Hard SPL or SuperCID process.
I personally have never tried to flash a cooked ROM without unlocking any of my devices. From what I've read what others have experienced...the flash would just fail and they're stuck in BootLoader Mode.
Myself ... I've experienced bad flashes, bad cooked roms that I've cooked, lost power to a pc & had my pc crash during a flash. Listed above is how I've recovered. There is life after Bootloader Mode.
The only time you have to worry is if your device does not power up at all
As a public chef...it's your responsibility to set the parameters of your ROM! Meaning, Radio, HardSPL, program conflicts, etc.
You are not ultimately responsible if someone bricks their phone but if they pushed the issue, you could be hit with some form of liabilty because you failed on providing a simple Disclaimer that sets the expectation.
I hope I've been helpful.....
Click to expand...
Click to collapse
Edit again:
And try like:
Plug in USB first, and thenn press & hold Camera, Power button etc.
I remember once I read there is a way to enter bootloader without battery, just can not find the original again.
So all my physical keys on my xperia x1 including the Volume button, the ok button, the X panel button, the pick up call button, the end call button, the two silver buttons all don't work. None of the keys on my keyboard work either.
I've been trying to hard reset but every method I've found includes holding down the volume button (which doesnt work since that button is unresponsive). I've tried the 2 silver button method along with the poking the stylus in the hard reset hole in the back of the phone but that doesnt work either since the silver buttons are unresponsive.
So now I'm looking for the Clear_Storage thing I've been reading about but I can't find it so could someone please supply me with the directory I could find it in or any other solution you can think of to help me hard reset my phone so I can flash a new ROM.
BTW I've used Hard-SPL to flash roms before, it's just this last ROM from itje got all screwy and made the buttons stop working.
Thanks, Nik
Setting > System > Clear Storage.
Sometimes Itje takes it out of his ROMs, though. You can try reflashing by pc method if it's not there.
Yea I've checked and it's not in there, how would you do it by pc?
Is it that ruu executable that you run while it's synced? For some reason
that never actually worked with my comp which is why I always resorted to the SD Card Flash method, but I can't get into the Hard-SPL loader now cause of the button problem.
Does anyone know how to hard-reset without having to use the hardware buttons, because I really need to be able to use my phone again.
Need Help =/
Next to malfunctioning buttons, is the phone starting up?
What happens, if you plug a USB cable in? If you can select ActiveSync mode, then you could easily try to re-flash another ROM image - maybe the one you have been using was corruptly downloaded or something.
Or, if you get too much of strange behaviour like this, try a stock ROM first, then another custom ROM.
It boots up and works fine as long as I stick to using the touch screen and I can USB ActiveSync it too. I know some of the older ROMs used to have an exe you could run while in ActiveSync and it would auto install but most of the new ROMs assume you're using the SD Card Method so I can't find the PC Installer app.
Alright so I managed to isntall a new version of that Firestorm Rom (3.8 I think) and my hardware buttons still don't work.
Like from the buttons that Works:
Power Button
Camera Button
Optical Joypad (only the center square)
Stuff that doesn't work:
X-Panel Button
Ok Button
Volume Button (up, down, center)
Pick up Call
Hang Up Call
Two Silver Buttons (left and right)
Left and Ride on "D-Pad"
ALL KEYBOARD KEYS
What is their left to do if a new ROM doesn't fix the problem?
what are my options for getting this fixed?
my volume keys dont work, dont know why but sometimes theyre working and sometimes not.
i have the same issue. but my g-letter button works. and all other buttons make the volume go up one notch and then down again. further more when i go into settings and the menu that controls what the buttons it only says it has a left and a right button.
have u been able to figure something out??
began working again
after a month it suddenly started to work again! dont know why or how
is a hardware problem, with your flex.
i can tell you this is hardware problem.flash your phone with orginal spl and orginal rom and send sony ericson.i had same problem.they gave me new unit after 3 months fight good luck.
no doubt, it's hardware problem..
Agree with human75, flash your x1 with stockSPL n original ROM before u send it to SE. Do it via your PC.. Goodluck bro
Someone please help me. I have installed HARDSPLV1 and everything appeared to be working, but every time I put a ROM on my storage card as Kovsimg.nbh and enter the bootloader tricolor screen it just says
KOVS100
SPL-0.72.OliNex
MicroP1-787
MicroP2-707
then Serial in the white part
then it says Loading...
No Image File!
What am I doing wrong? I have tried 2 different sd cards and 2 different ROMS with the same result. Someone please help if they can!
Have you unchecked "hide extensions of known files types" in Folder Options and made sure it isn't 'kovsimg.nbh.nbh' ? (I've seen this case, back a few months ago.. the creator of the thread never listened though)
What is the filesize of the rom you've placed onto the SD card(s)?
What was the filename+extension of the file before you renamed it? ruu_signed.nbh or was it some .zip or .rar?
There's other causes of this error, but just making sure the fundamentals are done correctly
Thanks to the above poster for offering his help^
However, I got it working, the problem was I didnt format the storage card with FAT32 prior to putting the Kovsimg.nbh file on it. I discovered you DO NOT need a card reader to do this on your PC. The X1 can act as a card reader when you set the option to disk drive select the disk drive in my computer after connecting the device and Format it with FAT32 there.
One thing though worrying me, I was not able to do a hard reset after installing the ROM onto my device, I tried depressing the two silver buttons while also depressing the power button and waiting for hard reset prompt to appear, but the device simply botted up as normal. Although, everything seems to be working fine without the hard reset. Any advice?
a hard reset is holding those silver buttons on the front and the button at the back of the phone, take off the metal cover and take out the stylus and you will see a circle, stylus covers it the button, hold that button too with the silver ones when on.
Oh word. well I was going by what BioVolt said in his tutorial... he said hold down both silver buttons and power button... but what you said makes sense since that didnt work,
Do you think I should hard reset the device even though the ROM has already been set up and everything seems to be working smoothly?
JoLLAJoLLA said:
Thanks to the above poster for offering his help^
However, I got it working, the problem was I didnt format the storage card with FAT32 prior to putting the Kovsimg.nbh file on it. I discovered you DO NOT need a card reader to do this on your PC. The X1 can act as a card reader when you set the option to disk drive select the disk drive in my computer after connecting the device and Format it with FAT32 there.
One thing though worrying me, I was not able to do a hard reset after installing the ROM onto my device, I tried depressing the two silver buttons while also depressing the power button and waiting for hard reset prompt to appear, but the device simply botted up as normal. Although, everything seems to be working fine without the hard reset. Any advice?
Click to expand...
Click to collapse
Even I had this problem of hard resetting my X1 initially while flashing ROMs. Then I found out that the trick lay in pressing down the two silver buttons and pressing the power button and the moment the phone gives the initial vibration, to release the power button. This way, you would be able to get into the hard reset screen. Try this and see.
And yes, I think a hard reset is advisable.
shantanil said:
Even I had this problem of hard resetting my X1 initially while flashing ROMs. Then I found out that the trick lay in pressing down the two silver buttons and pressing the power button and the moment the phone gives the initial vibration, to release the power button. This way, you would be able to get into the hard reset screen. Try this and see.
And yes, I think a hard reset is advisable.
Click to expand...
Click to collapse
Thank you for your advice, so you think a hard reset is a good idea even after the ROM is loaded and set up working properly? if you advise this I will do it.
JoLLAJoLLA said:
Oh word. well I was going by what BioVolt said in his tutorial... he said hold down both silver buttons and power button... but what you said makes sense since that didnt work,
Do you think I should hard reset the device even though the ROM has already been set up and everything seems to be working smoothly?
Click to expand...
Click to collapse
u have to press both silver buttons and then just press power button once and let it go right away that should do the trick
republicano said:
a hard reset is holding those silver buttons on the front and the button at the back of the phone, take off the metal cover and take out the stylus and you will see a circle, stylus covers it the button, hold that button too with the silver ones when on.
Click to expand...
Click to collapse
hard reset is just pressing 2 silver buttons and pressing power button, but you have to release the power button after the phone vibrates. thats all
JoLLAJoLLA said:
Thank you for your advice, so you think a hard reset is a good idea even after the ROM is loaded and set up working properly? if you advise this I will do it.
Click to expand...
Click to collapse
If your ROM is set up and working properly, then there is no need of a hard reset.
I usually flash through the SD Card method. After successful flashing message is displayed, I restart the phone and immediately perform a hard reset. Hope this helps.
^ thank you. Originally when I got the successful flashing message, I took the battery out and tried to do a hard reset. To this day, it hasnt allowed me to do one. instead of going the the hard reset prompt, the device always just boots up normally. Ive tried all different ways, hard reset by holding the two silver buttons and power button, and by holding the two silver buttons and just pressing the power button, hard reset by holding the reset button behind the batterycover with stylus and holding the silver buttons. All the same thing, just get the Sony Ericsson screen and the device starts up. I have spikegotti X1.5 6.5 ROM btw.
Hi All,
Hopefully someone can help me out here. I just suffered the unfortunate fate of having the beta ROM expire on me. Now it looks as though I will need to reflash the X1 with a new ROM.
If I reflash the ROM is there anyway that I can save my pictures and videos from the internal phone memory or will they get erased by the flash? If they get erased by the flash, can I recover them after?
Is there anyway to bypass the white screen that states the beta has expired? I really need to get to the pictures.
Thanks,
T
I don't have much experience with this(I don't even see the point why your rom isn't timebomb fixed). But are you able to connect via activesync?
No, I can't connect via active sync. The only thing that I see when I connect the phone to the PC is the removable sd card.
killer8nl said:
I don't have much experience with this(I don't even see the point why your rom isn't timebomb fixed). But are you able to connect via activesync?
Click to expand...
Click to collapse
What do you mean by "timebomb fixed"? Where do I find the timebomb fix?
no you cant recover it after flash.. if possible copy those files of yours to the sd card.. then flash.. frankly speaking i didnt know that there was a rom with a expiration.. really.. got me confuse there bud..
Hi ,
same case here. I had an energy ROM which does not have time bomb fixed and now all the internal data needs to be saved. i have also looked to many posts to seek solution and being a newbie was reluctant to ask around. if anybody has a solution pls post. this effects WM6.5 series ROMS. Thx in adavnce for help
i doubt you will get the images back i dont know what format is the phone is, if you flash over it or with a smaller rom, the sectors will be free for allocation, but if you manage to use data recovery program you might have a chance depending on the allocation size, they tell you to hard reset after flash so there is something left behind, but its interesting to know that in the tri color boot screen connects to the pc via usb so there is some communication there.
good luck
Did anyone ever figure this out?
This stupid ROM that has expired seems to prevent the bootloader from starting up somehow.
I tried holding the volume down button while pressing and holding the power button, but it always boots into the Energy ROM. Instead of immediately seeing the tricolor screen, I get the SE logo followed by the blasted HTC logo then the Energy ROM.....
I have tried doing a hard reset (stylus in the pin hole with the two silver buttons on the front pressed down) and no luck...it just boots up normally....
I really need to get my files off of the phone, but I cannot access it via Activesync (phone not visible), and the blasted screen on the phone is completely white with a stupid message. Man I am really p***** off./
If anyone here can help I would really appreciate it as I have some files that are very important that I desperately need to get off the phone...
PLEASE HELP!!!!!!!
taz1973 said:
Did anyone ever figure this out?
This stupid ROM that has expired seems to prevent the bootloader from starting up somehow.
I tried holding the volume down button while pressing and holding the power button, but it always boots into the Energy ROM. Instead of immediately seeing the tricolor screen, I get the SE logo followed by the blasted HTC logo then the Energy ROM.....
I have tried doing a hard reset (stylus in the pin hole with the two silver buttons on the front pressed down) and no luck...it just boots up normally....
I really need to get my files off of the phone, but I cannot access it via Activesync (phone not visible), and the blasted screen on the phone is completely white with a stupid message. Man I am really p***** off./
If anyone here can help I would really appreciate it as I have some files that are very important that I desperately need to get off the phone...
PLEASE HELP!!!!!!!
Click to expand...
Click to collapse
I'm sorry that I still have no clue how can you get your files...so sorry
About entering the bootloader, the main point is, did you continue holing the down volume button while you are holding the power button??
Hold volume button, press and hold power button (still keep holding the volume button), wait and you will see 3 color screen....
hope you can some how to connect to the computer...
Good luck....
I keep holding the volume down button while I press and hold the power button and it just boots up normally...
I have even trien a hard reset and it also just boots up normally...
wtf....
you can also use the camera button instead of the volume keys... camera+power... that's what i do
seems as tho everyone who has this problem with the volume keys are the only ones who use custom roms
HolyChristmas!!!! That worked...it was the only %^## combination of buttons that I did not try. Thanks a million spike.
Not when I have my X1 in boot loader mode and then connect to the PC, will I be able to access the files on it using Activ sync? Right now I see nothing.....
taz1973 said:
HolyChristmas!!!! That worked...it was the only %^## combination of buttons that I did not try. Thanks a million spike.
Not when I have my X1 in boot loader mode and then connect to the PC, will I be able to access the files on it using Activ sync? Right now I see nothing.....
Click to expand...
Click to collapse
You can plug your USB in your X1 while in bootloader, so you can flash a new ROM, you can't back-up your files from there.
glad to here that ur problem i solved
The problem solved?....50% but not quite completely out of the woods yet.
Now that I can get to the bootloader, I need to fetch my personal files from the phone memory before flashing a new ROM onto it. So that is where I stand now.
I know that the phone is somehow communicating with the PC as I was able to re-run the HARD-SPL as a test and it worked. Now it is a matter of getting the phone to be seen by the PC so that I can get my data from it....the data is very important to me so I cannot afford to lose it.
AAny suggestions short of applying blunt force with a hammer will be appreciated...
taz1973 said:
I keep holding the volume down button while I press and hold the power button and it just boots up normally...
I have even trien a hard reset and it also just boots up normally...
wtf....
Click to expand...
Click to collapse
your data is already gone if you already did a hard reset, so there is no way to get it back.
The phone can't communicate with your pc unless winmo is up and running and activesync service is running, so from within the bootloader, i think it isn't possible.
You could read around at the forum on how to make a dump of your rom, then all files on your phone will be "dumped" to the pc. But i don't know if you can do that through the bootloader. Good luck
EDIT: Ow, sorry, I didn't look to the last posts, i see you already found out that the camera button already works.
To get in bootloader, try the camera button and the power button instead of the vol. down button.
I know that the data is still there for the following reasons:
1. hard reset was not done
2. when phone boots up normally I do the the custom desktop background (which is a picture that I took with the camera) before it gets covered up by that white screen with the "beta expired" message.
3. I am able to communicate with the phone because when I was in bootloader mode, I ran the Hard-SPL.exe from my PC and the phone responded by loading the hard-spl.
I also thought of trying to dump the ROM, so that is one of the things that I will try soon.
Any other suggestions of how I can access my files in the phone memory?
Just took a look at the "how-to dump your ROM" guide and it does not look feasible considering I can't see the screen because of the white "beta expired" message. However, since I was running a custom ROM, perhaps the sdkcerts.cab was already pre-installed along with the registry settings...will try it anyway.
Any other ideas?
"
2) Preparing your phone:
Before your X1 will allow the dumping to be done, the following Sdkcerts.cab file must be installed.
- Copy Sdkcerts.cab to your phone or storage card and install it to the device.
Also, your phone must accept changes that pdocread makes. You can do this with the regedit function of the FdcSoft Taskmanager.
- Set the following registry keys to "1":
* HKLM\Security\Policies\Policies "00001001"
* HKLM\Security\Policies\Policies "0000101a"
- Connect your phone to your pc with activesync.
"
in the future, never save info on ur device that's valuable, im sure this is the reason why u have a sd card... i learn this the hard way on my p1i
just imagine you having info on ur device thats valuable and something else had happened, your goose would have been cooked... utilize the sd card as a safe storage way and always keep backups on an external storage... even myphone service from M$ gives this...
wish u luck in getting that info
I think that I definitely learned my lesson this time around...I am usually a bit more careful with my data....perhaps a moment of insanity lead me to this.
Back to trying to recoup the data....