Related
I have looked everywhere but no luck! Can someone please give clear instruction how to replace the digitizer/touch panel?
I have only found instructions how to disassemble the diamond up to the LCD stage only! But after that it does not show how to take the LCD out of the housing to expose the Digitizer.
Hope someone knows how to do it.
Thanks.
The instructions you looked at, where they from the Service Manual or another source?
one from the service manual at XDA-WiKi page and other post from http://www.pdacenter.ru/razborka/razbor-htc-touch-diamond
but both goes up to the same stage and stop.
Yeh I've got the same service manual and it doesn't really go into any detail about how to replace the digitizer. Maybe there's another 'level' of the Service Manual for that. Only question is, where does one obtain it? Good luck replacing it - how come you're replacing it btw? Your touch screen not responding?
Digitizers (touch screen) usually are not being replaced at all. The LCD screen (with digitizer) is the one block. And it is being changed completely in service centers.
But: If you can find just digitizer, then you may cut off with office knife the digitizer from the lcd-screen itself (on borders only, do not cut your screen) and then place the new digitizer on the screen firmly (it will stick to it on borders).
I've done it with my treo 750 yesterday.
kortez said:
Digitizers (touch screen) usually are not being replaced at all. The LCD screen (with digitizer) is the one block. And it is being changed completely in service centers.
But: If you can find just digitizer, then you may cut off with office knife the digitizer from the lcd-screen itself (on borders only, do not cut your screen) and then place the new digitizer on the screen firmly (it will stick to it on borders).
I've done it with my treo 750 yesterday.
Click to expand...
Click to collapse
Thanks for your input. Digitizers for Diamond are available for sale separately.
just to make sure i got this right, if it is only fixed on LCD by sticking to it without any screws can i pry it out from the front side without disassembling the diamond?
Scratched screen
Ok, So I finnaly scratched the screen. Quite badly, must add !!
I was wondering the costs to replace the screen. Do I need a whole case / digitizer or lcd ?
Also what would the costs be roughly, as I am unable to contact my local repair shop....
dalewinterstein said:
Ok, So I finnaly scratched the screen. Quite badly, must add !!
I was wondering the costs to replace the screen. Do I need a whole case / digitizer or lcd ?
Also what would the costs be roughly, as I am unable to contact my local repair shop....
Click to expand...
Click to collapse
digitizer arround 29 USD + shipping.
not sure if LCD is available yet.
if you scratched the screen you will only need to replace the digitizer which is the actual screen you press on.
the only thing is no clear instruction how to replace it!
ammar said:
Thanks for your input. Digitizers for Diamond are available for sale separately.
just to make sure i got this right, if it is only fixed on LCD by sticking to it without any screws can i pry it out from the front side without disassembling the diamond?
Click to expand...
Click to collapse
Without disassembling - no, for sure.
And seeing the video - I would not suggest you to, it's quite hard, cuz it's all packed very tight.
I heard that there's glass in front of screen on diamond that sends the pressures to the real touch screen. But that maybe not true. I guess you'll have to disassemble the diamond to see what the touchscreen is on it.
Or you shoudl find the video, where you can clearly see if the touch diamond' screen have any protective glass..
Kortez,
thanks for your help, do you have link to the said video?
thanks
can't remember where I've seen. But it exists.
http://www.youtube.com/watch?v=_jY46M_NGz0
Check ou this web site
http://www.dealextreme.com/
it has very replacement parts and with a very good price, and free shipping!!!
I've just recived my tytn II digitizer for only 4,99.
Hope it helps.
tape said:
Check ou this web site
http://www.dealextreme.com/
it has very replacement parts and with a very good price, and free shipping!!!
I've just recived my tytn II digitizer for only 4,99.
Hope it helps.
Click to expand...
Click to collapse
We need the instruction on the replacement step, not the part.
I've just replaced the digitizer now on my Diamond...having issues getting it back together though, will go into it in a minute.
Originally I ordered only a digitizer, then dismantled the phone and hit a brick wall when I tried getting the screen from the metal fascia, the adesive is really strong, I actually ended up cracking the screen under the digitizer and so ended up having to buy a screen with a digitizer for £10 more - to be honest I recommend this is what you do - if you order just a digitizer then you have to mess about soldering the cable onto the cable of the screen (as well as getting the broken digitizer off the screen and probably cracking it in the process)
Anyway, my new one came today, managed to put it onto the fascia fine and have started putting the thing back together, but I cant connect the 2 cables to the mainboard part! cos for a start theyre underneath and not long at all! anyone have any ideas?
Adam86 said:
I've just replaced the digitizer now on my Diamond...having issues getting it back together though, will go into it in a minute.
Originally I ordered only a digitizer, then dismantled the phone and hit a brick wall when I tried getting the screen from the metal fascia, the adesive is really strong, I actually ended up cracking the screen under the digitizer and so ended up having to buy a screen with a digitizer for £10 more - to be honest I recommend this is what you do - if you order just a digitizer then you have to mess about soldering the cable onto the cable of the screen (as well as getting the broken digitizer off the screen and probably cracking it in the process)
Anyway, my new one came today, managed to put it onto the fascia fine and have started putting the thing back together, but I cant connect the 2 cables to the mainboard part! cos for a start theyre underneath and not long at all! anyone have any ideas?
Click to expand...
Click to collapse
I thought the digitizer cable can be just slot into the connector type, no? Did your digitizer come with soft ply tools? which to help on plying out the screen and digitizer i heard. I'm gathering info before placing my purchase on the digitizer... Coz its badly scratches, felt and kicked!
No unfortunately not - you have to solder it on theres some contacts for it.
I managed to get all mine back together you just have to take your time and be really careful - it works perfectly now. I'm really chuffed as its a really good spare to have
If I was you i'd order a screan and a digiziser together cause then it will just be a case of pulling the screen off the adesive on the fascia (it's stuck really well you might even crack your broken one like I did) and then stick the replacement on and reassemble!
Hi, could anyone of you make some pictures or a small video about how to get the display out of the body, or where exactly i need to pull the display out.
i have already dismantled my diamond, but still didnt get the display and digitizer out. When i pulled the display i think i broke it somehow, because now my display shows me only stripes...
anyway, my ordered display still didnt arrive....
if you could make a vid or some pictures, it would be very helpful.
Adam86 said:
No unfortunately not - you have to solder it on theres some contacts for it.
I managed to get all mine back together you just have to take your time and be really careful - it works perfectly now. I'm really chuffed as its a really good spare to have
If I was you i'd order a screan and a digiziser together cause then it will just be a case of pulling the screen off the adesive on the fascia (it's stuck really well you might even crack your broken one like I did) and then stick the replacement on and reassemble!
Click to expand...
Click to collapse
how was the soldering part? difficult? as i heard it might melt the plastic cable, no?
If i do cracked the existing digitizer, no harm i see since its already borken though.
Well, i managed to get the lcd and tocuh sceen apart, and now am stuck with the soldering part either.
the sceen has to be pushed out from the inside....the glue they used is pretty strong. and the display breaks pretty fast....
isnt there a way to connect the lcd and ts without soldering?
Hey,
Just looking for some advice where I should go for a cheap solution on how to fix my phone. Basically, everything still works great! Apart from the big crack, the screen doesn't seem to have been damaged (eg. All the pixels look fine, touch still works, only glass/plastic panel is cracked)
I'm actually really impressed by how it took such a hard hit and the device works fine, the screen didn't even smash! Basically it nudged in between my car seat where you close the door, didn't realise it fell out my pocket and closed the door (you could imagine it would be a hard hit) and the phone lives.
If I just needed the glass replaced, can it be done DIY? Or should I not bother and give it to a service centre? I got it from 3 but I know they'll probably overcharge me for something like this..
Any suggestions welcome, thanks!
if the damage is only to the exterior screen then you may want to consider getting this:
http://www.mobilefun.co.uk/product/17042.htm
be carful! the screen from my firlfreidns diamond is broken too and I had ordered one of those touchscreens... but the screen which comes has no "window" for the frontcamera and after disassembling the phone I saw that it is NOT POSSIBLE to remove the touchscreenglas from the frame.
Replacement LCD & Digitiser
I recently replaced an lcd and digitiser on a HTC Touch Diamond. I bought the complete screen (lcd & digitiser) as one pre-assembled unit from a guy on Ebay (£34.99). Fits straight into the front of the unit frame. I don't think you can remove just the digitiser because it is stuck onto the LCD, and the LCD itself is very fragile. Disassembly is fairly straight forward if you've got the right tools.
Thanks for all your help guys! I've just been bogged down with work so havn't been able to get back here for awhile.
I've taken some time to look into the webiste and others, decided to just order it off ebay in the end anyways. However, taking note from the previous 2 posts, would I be wasting my time ordering just the digitiser itself? I would assume that's what HerrVorragend also meant by "that it is NOT POSSIBLE to remove the touchscreenglas from the frame."
If so, why do they bother selling them online separately? I guess I won't really find an answer, just seems stupid to me. Anyways, guess I'm stuck purchasing both LCD + Digitiser but as a final question, does anyone have any guidelines as how I should replace this myself? I'm very paranoid about this sort of thing because it's only 1 month old, however, I have also replaced an LCD on my old Nokia 6280 before using a step-by-step picture guide online.
Don't think I'd have much luck finding one for this model, hey.. haha.
Once again, thanks!
Double posted, sorry.
badtzmaru56 said:
If so, why do they bother selling them online separately? I guess I won't really find an answer, just seems stupid to me. Anyways, guess I'm stuck purchasing both LCD + Digitiser but as a final question, does anyone have any guidelines as how I should replace this myself? I'm very paranoid about this sort of thing because it's only 1 month old, however, I have also replaced an LCD on my old Nokia 6280 before using a step-by-step picture guide online.
Don't think I'd have much luck finding one for this model, hey.. haha.
Once again, thanks!
Click to expand...
Click to collapse
If you google for HTC Diamond Service Manual, that will help greatly with assembly and disassembly - there are also a couple of videos on Youtube. From my experience the most tricky part is re-connecting the two flex connectors when you re-install the main board. I use the back of a pair of tweezers to slide underneath the connector carefully. If you are nervous about doing it and happy to cover postage costs, I can replace the LCD for you - PM me for details and I'll see what i can do.
Andy
My touch screen stopped working on my phone, but the screen is still visible. I'm assuming it's the digitizer. I was wondering if anybody has done or tried replacing only the digitizer. Does this work, is it better just to replace both? Any suggestions? Thanks.
Save yourself the headache
Just replace the complete screen unit (lcd + digitizer).
The digitizer is held on the screen with some super strong adhesive that is nearly impossible to get off cleanly. Also, there are three (4?) thin ribbon tabs that have to be soldered to the board on the rear of the lcd. Unless you are really confident with a soldering iron, it is extremely hard to do.
I replaced my screen unit in about a half hour. Make sure you go to the wiki and find one of the excellent disassembly guides before you start.
Thanks
Thanks, that's exactly the information i needed to know. I found the fon logix video. Is it only a t6 tool i need, or do i also need a t5. I have seen conflicting info on this? Thanks again.
I got my scren unit from ebay, and it included a torx driver and a plastic case tool. I honestly can't remember what size came in the kit, because I used my own torx set. Im pretty sure its just the one size, though.
Good luck!
You might find this information interesting.
http://forums.wireless.att.com/cng/board/message?board.id=cingular&thread.id=116836
Disregard ............
i always replace only the touch screen. okay i've done it aprox 30 times. But i never broke one.
if you decide to replace only the touchscreen, there are 2 types. thus check which on you have, and i found out that sometimes reassamble, and cleaning can help.
good luck.
torx is 5 and 6, 6 for opening the back of the phone, 5 for the screen part removal of the body and opening it. you need an opening tool!!
adhesive
is there a terrible adhesive between the screen and digitizer, as the second poster mentioned? how difficult is it to deal with?
just cut away with snapoff knives. It wil break in more pieses. (the glas that is) just be carefull, and take your time
Thanks
Thanks for all of the info, i went ahead and purchased the screen with the digitizer and tools. One thing i have noticed though is the d-pad has stopped working also, i'm using a custom rom so i'm not sure if it's just that or it's something else. i will prob re-image after i replace screen.
Abel2007 said:
just cut away with snapoff knives. It wil break in more pieses. (the glas that is) just be carefull, and take your time
Click to expand...
Click to collapse
Well, guess I was a smarty pants and bought my stuff before consulting XDA...as such, I ONLY bought the touchscreen rather than the entire new unit. Cheaper, yes, but I had no idea about the adhesive until just now. My only question is, once I remove the old screen from the LCD with a razor blade, how do I affix the new one?
Anyone?
i would love to know this too because i have to also replace my digitizer!
drokkon said:
Well, guess I was a smarty pants and bought my stuff before consulting XDA...as such, I ONLY bought the touchscreen rather than the entire new unit. Cheaper, yes, but I had no idea about the adhesive until just now. My only question is, once I remove the old screen from the LCD with a razor blade, how do I affix the new one?
Anyone?
Click to expand...
Click to collapse
I used rtv gasket maker the transparent blue one worked well.
you can find it in automotive section. Actually any silcone will work.
also can use double sided tape but needs to be very thin
I've already changing my digitizer, but it doesn't seem to work. So I've change the whole part. cost me $20 more on ebay.
my advice is to change the whole package with the lcd too.
Hi,
the touch screen of my Xperia V is broken and I'd like to replace it myself. It's not the first time for me that I repair a mobile device myself, but without a disassembly guide, it is difficult for me to identify the parts that are fixed by glue. I don't want to break anything that is still working.
I already found a russian video on YouTube, but it seems to me that the display is not taken apart from the other parts of the device.
Has anyone here done it before?
Thanks in advance!
Display removal
grisu59964 said:
Hi,
the touch screen of my Xperia V is broken and I'd like to replace it myself. It's not the first time for me that I repair a mobile device myself, but without a disassembly guide, it is difficult for me to identify the parts that are fixed by glue. I don't want to break anything that is still working.
I already found a russian video on YouTube but it seems to me that the display is not taken apart from the other parts of the device.
Has anyone here done it before?
Thanks in advance!
Click to expand...
Click to collapse
Hi,
I've managed to remove the display. Mainly because it was really damaged ... heating the display and "bending" with a small tool.
It's really hard as the glue is quite strong. As my replacement screen is "on it's way" I'm not able to finalize the work.
I'm kind of stuck in the part when removing the "middle, plastic" part...
display is connected to body with really strong glue. Remember that it is impossible to remove old display without breaking it. Second thing is that with new display the phone most likely will not be waterproof
hakanW said:
Hi,
I've managed to remove the display. Mainly because it was really damaged ... heating the display and "bending" with a small tool.
It's really hard as the glue is quite strong. As my replacement screen is "on it's way" I'm not able to finalize the work.
I'm kind of stuck in the part when removing the "middle, plastic" part...
Click to expand...
Click to collapse
Hi! I broke mine last night. How did your repair go when the part arrived? I also could only find the russian video without the screen being removed
How hot did you have to make the screen? I was thinking of using an iron with a cloth around it.
Hi Folks, I'm curious to hear how others are going - I managed to break my screen this last week, Hoping to replace it but so far taking out that glass seems to be a tricky thing - any suggestions? How did the iron and cloth go?
canuck82 said:
Hi Folks, I'm curious to hear how others are going - I managed to break my screen this last week, Hoping to replace it but so far taking out that glass seems to be a tricky thing - any suggestions? How did the iron and cloth go?
Click to expand...
Click to collapse
There's no way.... You need to buy a new housing with the LCD and touchscreen built in, and then move all your bits over. That's why the russian video of the guy removing everything doesn't remove the screen.
Daryl_tt said:
There's no way.... You need to buy a new housing with the LCD and touchscreen built in, and then move all your bits over. That's why the russian video of the guy removing everything doesn't remove the screen.
Click to expand...
Click to collapse
I just ordered this: http://www.parts4repair.com/complete-screen-assembly-for-sony-xperia-v-lt25i/ I will see how that goes. I got tired of using my old SG1 so it's time to fix the V...
Good luck. Careful with the tiny, white antennae cable running from the main board to the bottom. I twisted mine a little bit too much and the connector popped off. I had to go get a new one with much difficulty.
Update
Daryl_tt said:
Good luck. Careful with the tiny, white antennae cable running from the main board to the bottom. I twisted mine a little bit too much and the connector popped off. I had to go get a new one with much difficulty.
Click to expand...
Click to collapse
I replaced the screen - had it working for two days and dropped it again - cracked screen, doesn't even light up.
I now have another replacement screen and a better case - at least now I'm getting quicker at taking the phone apart....
screen help
canuck82 said:
I just ordered this: I will see how that goes. I got tired of using my old SG1 so it's time to fix the V...
Click to expand...
Click to collapse
Hi this wont work, I went through the exact same issue, and its impossible to attach the new screen properly. your best bet is to try and find a second hand screen via ebay. it has to have the "housing part with it. otherwise you are wasting your time. it cost me so much to fix mine as I ordered two screens in the end I could have bought a new phone on special....
Try Ebay, and make sure you see the one with the screen and front housing on, I am unable to port the correct link on here as I haven't made 10 posts yet.
Search for the following on ebay : Genuine Sony Ericsson Xperia V LT25i front+digitizer touch screen+LCD display
This should let you find the correct screen
Look at the picture you will see the side housing for the front is also installed, the one you have ordered is the incorrect one as its only the LCD and the Digitzer, without the front housing that it gets "glued" onto. You can see the main difference where the earpiece is its shown as black, hence the mesh is there. that would be the correct one to order. Unless you have the means of getting yours glued back on the same way as the factory, I see you will struggle to get it done otherwise.
Hi guys.
I've dropped my xt1068 on a floor and the glass got cracked although the screen works perfectly (no damaged parts at all). I've buyed the replacement glass from ebay (this one http://www.ebay.com/itm/Black-Front...244?pt=LH_DefaultDomain_0&hash=item566c04b4ec ).
My question is, have anyone passed through this situation? Is there any way to replace it without damaging the screen? I heard that glass is glued to the digitalizer screen and I'm worried.
Any thoughts?
Antique_Angel said:
Hi guys.
I've dropped my xt1068 on a floor and the glass got cracked although the screen works perfectly (no damaged parts at all). I've buyed the replacement glass from ebay (this one http://www.ebay.com/itm/Black-Front...244?pt=LH_DefaultDomain_0&hash=item566c04b4ec ).
My question is, have anyone passed through this situation? Is there any way to replace it without damaging the screen? I heard that glass is glued to the digitalizer screen and I'm worried.
Any thoughts?
Click to expand...
Click to collapse
I don't think it is glued, but if it is try putting some light heat on it, not real hot though. The glass is meant to be replaced. I'm guessing you have the disassemble instructions.
https://www.ifixit.com/Guide/Motorola+Moto+G+2nd+gen.+2014+LCD+screen+Replacement/36180
Tel864 said:
I don't think it is glued, but if it is try putting some light heat on it, not real hot though. The glass is meant to be replaced. I'm guessing you have the disassemble instructions.
https://www.ifixit.com/Guide/Motorola+Moto+G+2nd+gen.+2014+LCD+screen+Replacement/36180
Click to expand...
Click to collapse
Thanks. But the video shows how to replace the whole screen, I just bought the glass (which I need to replace). I've little concerned about separating glass from screen.
And the only tutorial I found is for samsung galaxy s4.
Antique_Angel said:
Thanks. But the video shows how to replace the whole screen, I just bought the glass (which I need to replace). I've little concerned about separating glass from screen.
And the only tutorial I found is for samsung galaxy s4.
Click to expand...
Click to collapse
I'd give it a shot. The worst you could do is have to put it back together with the broken glass. It's a pretty straightforward job taking it apart. Just be careful with the pins on the cables you unplug.
Tel864 said:
I'd give it a shot. The worst you could do is have to put it back together with the broken glass. It's a pretty straightforward job taking it apart. Just be careful with the pins on the cables you unplug.
Click to expand...
Click to collapse
Thanks!
I've also bought a uv glue to glue it better. After the process, I'll share the results.