After replacing my digitizer, I needed to align my screen because it was off. It worked the first time, but later I had to readjust the plug of my digitizer into the motherboard. Now I need to re-align it again because it is again about 2-3cm off. When I go to the align screen page, it just loops. There are many threads on how to skip this page and stuff, but I NEED to re-align my screen and it will not. Please help.
For some reason the right side of the screen is more off than the left side, which is less unaligned, but still difficult to type with
does no one have any idea what can be done? Is there any 3rd party software that will allow me to align my screen?
Or can someone give me the calibration number that are in the registy? Perhaps I can mess with those.
Can someone please check their registry for the calibration numbers?
They are located at HKEY_LOCAL_MACHINE\Hardware\Devicemap\Touch\CalibrationData
Thanks.
HKLM\\HARDWARE\DEVICEMAP\TOUCH\CalibrationData
510,545 186,875 179,208 836,206 830,883
did you solve this? I have the same problem
Related
My touchscreen won't allow any input. I tried hard reset, reflashing ROM and radio - nothing helps so far. Now it's stuck on the 'tap the screen to setup your device' on the initial setup screen. The buttons work, slide works, but touching the screen won't. Any ideas? I saw the posts about frozen screens, but I don't think this is it.
Ozark_8125 said:
My touchscreen won't allow any input. I tried hard reset, reflashing ROM and radio - nothing helps so far. Now it's stuck on the 'tap the screen to setup your device' on the initial setup screen. The buttons work, slide works, but touching the screen won't. Any ideas? I saw the posts about frozen screens, but I don't think this is it.
Click to expand...
Click to collapse
Maybe its a loose connection?
Uh - is there a way to tighten it??? ;-)
Any ideas? If the screen is hosed - any suggestions as to who could repair it?
Bump? How about difficulty in replacing the screen on these?
Ozark_8125 said:
Bump? How about difficulty in replacing the screen on these?
Click to expand...
Click to collapse
just did mine, it's not TOO bad.. just 4 screws and a lot of careful prying but it's definately doable. There is a how to somewhere on here. If I were you I'd try the tool that lets you skip the screen setup and see if your touch screen works otherwise... strange thing is when I try to align my screen right now it freezes my phone on the "align screen" screen... so hopefully that's what is happening to you and you dont need a new screen. so yeah look for the align screen skip and see if it works.
Thanks for the info - I'll look around for the skip alignment tool. I assume the screws were those outer four teeny tiny torx screws?
OK - Dude - how crazy is that... it just started working again. I just kept hitting around on the screen by forcing it to alignment and it's now working. What gives? I saw a post about magnetization screwing up alignment, but this is kind of crazy. It works if I push the screen part of the phone 'south' and then I can tap and get the alignment to complete. Loose connection somewhere, I'll check out those guides to figure out if the ribbon is tight or not.
Ozark_8125 said:
OK - Dude - how crazy is that... it just started working again. I just kept hitting around on the screen by forcing it to alignment and it's now working. What gives? I saw a post about magnetization screwing up alignment, but this is kind of crazy. It works if I push the screen part of the phone 'south' and then I can tap and get the alignment to complete. Loose connection somewhere, I'll check out those guides to figure out if the ribbon is tight or not.
Click to expand...
Click to collapse
glad to hear you've got it working and saved yourself a headache... you might want to try sliding it open and giving it a squeeze below the screen but above the buttons... that's where the screen attaches to the board... give it a try.
OK - more of a 'tard moment for me - the screen protector was jamming against the screen. I figured that out after I had the whole back off and pried open to look internally to see what was going on and then noticed the screen was working fine with the back off.... oh geeze, time for a stiff drink. Thanks for the suggestions - you guys are cheap therapy bahahahahhaaaa!!!
Look out for dust particles
Glad you found out what was wrong. I would like to add that in general, if a touch screen is unresponsive, examine the device for dust particles stuck between the plastic and the touchscreen. It will be understood as a tap by the touchscreen, thereby rendering your own tabs unrecognized. I've tried that 2 times now.
I had a similar problem with my touchscreen. Sometimes it doesn't recognize my touch with a finger or stylus. I have to keep pushing the same spot for it to register the touch.
Now I took a needle and cleaned the space between plastic and touchscreen. For now it seems that it helped. Lets see how it works for now on.
Thanks.
ha ha ha ha ha!!!!
at leats you admint the retardness
D'oh.. the problem stays. Do I have to open the whole machine, and clean it that way, or can the problem be in the software?
I think, that after a soft reset the screen works properly, but after a little while it overlooks some of my taps.
What SPL are you running? Are you experiencing the 'screen freezes'?
"XDA-Developers HTC Kaiser HardSPL CID Unlocker v1.0" says in the readme.txt file. Does 'screen freezes' mean that I can't do nothing with the screen, or what? What is the SPL's job in the PPC, I thought it was needed only for the OS flashing.
OK, now I know what you mean with screen freeze. It sure does freese. So the problem is not in the touchscreen, but in somewhere else? The whole phone freezes in time to time.
what spl are you running?
OK, I suppose that was a tip. Thanks for the tip. I upgraded my SPL from 1.0 Olipof to HardSPL 3.56.
Everything started going very smoothly for now. Lets see how it keeps being smooth after couple days of using.
I just replaced a screen in a Trinity (Dopod D810). The touchscreen initially wasn't calibrated correctly so I ran the alignment tool in the settings, and after a few attempts, I calibrated it properly and the touchscreen was working perfectly. Now the touchscreen is not working properly. The top half of the screen responds to touch, but no matter where I press in that region, the screen thinks I'm pressing the top-right corner. When I run the alignment again, it responds to all the touchpoints but it never successfully calibrates and it keeps bringing me back to the alignment screen.
The current settings in the registry entry for touch calibration are as follows:
484,558 244,286 263,815 750,820 707,295
I've found a few other threads here (the most helpful being http://forum.xda-developers.com/showthread.php?t=355010) and I've tried the settings from that thread. The screen seems more responsive, but still not correct because the bottom half hardly responds and the top half seems to respond when it feels like it.
Can someone please post their D810 touchscreen settings so I can try it? I've tried the settings from my Touch Cruise, but the screen is still doing weird things.
This is a customer's phone so I need to have this fixed ASAP.
I'm thinking that it may be a faulty digitizer, but that won't explain why it worked perfectly when I first calibrated it.
UPDATE: NOT FIXED yet, but now the backlight is dead. I just turned it off, and then turned it on again, but I can only see the screen content if I shine a torch onto the screen. The LCD hasn't leaked. The backlight just died and the connectors in the phone are fine. Perhaps this was a dodgy screen.
Any ideas?!
since the device has a recessed screen, take the cover off to get at it.
take a soft cloth or something and clean off all the garbage on the digitizer and back of the plastic. make sure everything around the lcd is free of dirt.
usually, if there is something pushing down on the digitizer while you calibrate it, it will totally bork the alignment over the course of 10 minutes to an hour.
my kaiser is currently having this issue, though i put it though alot more hell then i should have... so i suspect its suffering from other issues.
I need some help/questioned answered and am hopeful someone here can help
I am trying to replace a broken touch screen on an att tilt but when I replace it with a new screen and turn on the phone, the touch screen doesnt work. Is there something special I need to do? ie software update/hard reset? Or on the touch screen there is the flexable cable the wraps around to the back of the lcd with 4 connectors, is there a special way of attaching it? ie glue? it looks like the old one was just held done with tape, but I did the same thing and am wonderingh if it is connecting. I can upload photos if you dont understand what I talking about.
Please someone/anyone help. all suggestions are greatly welcomed.
I am in a little bit of a rush so I dont know if I explained everything clearly, I hope so
replace lcd
Hi, I replaced mine and there is just a ribbon cable that plugs in...it can be kinda tricky but basically you just line it up and slide it in...Theres a couple of threads on here with detailed instructions you can find by using the search, thats how I learned how to do mine. The only thing I had to do afterwards was the touchscreen alignment function that you normally do when first installing the OS because it seemed my touchscreen was slightly off..after that it was fine.
Hi all,
I recently bought a used X1, wich already had a custom OS (Christian's) installed.
It's an excellent device, though there is one thing that really pisses me off.
The screen alignment is off all the time. No matter how often i re-align, after a short while it always is a few milimeters of, especially on the top half of the screen. So, for example if i want to press a button, i have to press above or under it, else it doesn't work.
I already tried cleaning the edges of the screen, even with pressurized air. Didn't help though.
Is there any solution for this or have i just been ripped off by the seller of this device?
Btw, excuse my english .
Can anyone help me please?
I mean, i really love this phone. But the touchscreen issue makes it kinda useless to me.
Is there any fix for it or is it just the way it is untill i replace the screen?
Hard reset. Or re install the ROM
Make sure to take your time while aligning your device, get some very precise points in or it will throw it all off. If all else fails you can try re-installing, but that probably isn't the problem if realigning fails. Possibly a screen issue?
I hard-resetted (?) and reinstalled the os, didn't work though.
When i re-allign it's all ok, but if i go to 'notes' then, and draw a little, it quickly becomes mis-alligned again.
The line is sometimes drawn more then a centimeter below the stylus :S .
I assume this is not a software problem, perhaps the screen is broken?
Anyway, i'm selling it back to the previous owner...
when i had a problem similar to this it was my ribbon cable that had worn away with sliding the keyboard in and out.
Hello, I am a true noob so please forgive me if I sound dumb.
I had a broken screen so I bought a new one on Ebay. I changed it perfectly, it looks good but now when I touch the screen it acts like I touched the top left corner (in portrait)no matter where on the screen I touch (so it opens up the "Start" menu). In landscape it acts like I touched the top right so it opens up the drop down menu with all the running programs.
I would really appreciate some help. I try re-aligning the touch screen but it does not recognize any touches at all. I have to soft reset the phone to get out of the re-align program.
I don't want to hard reset because I have read many cases where the phone gets stuck in align program as it is trying to setup and they have to install remote access or something to get around it.
I would like advise on whether it is the new screen or the phone. Is there something I can check for inside or should I send the screen back for a replacement.
Thank you for your help.
Having replaced the touch screen in a Palm with success, I would say that...
You either have a problem with the connector for the screen, recheck the connection
Someone sold you a bad screen.
Something else is wrong with the device.
At this point I don't know that in your position I wouldn't do a hard reset. What is the worst thing that can happen? The device is already broken in it's current state.
Good luck.
Thank you
Thank you very much for your help. I will try the connector. if it does not look damaged then I will return the screen.
Did you replace just the screen itself, or the screen and the digitizer? More than likely your digitizer is broken aswell. If you replaced them as a set, request a new one from wherever you got it, and if you just replaced the LCD, then you need to buy a digitizer aswell.
ashasaur said:
Did you replace just the screen itself, or the screen and the digitizer? More than likely your digitizer is broken aswell. If you replaced them as a set, request a new one from wherever you got it, and if you just replaced the LCD, then you need to buy a digitizer aswell.
Click to expand...
Click to collapse
Well, I only received the screen. I cant figure out where the digitizer is on the tilt so I don't know if I changed it or not. Does any body have any picture??
I think I read somewhere that it all comes as one piece(the screen and digitizer), but I can't confirm it.
Indeed they most of the time do come as one peice, so if your connection is good on the mobo, then I would say that the digitizer you recieved is bad. The digitzier is the super thin peice of glass that covers the LCD screen.