Hi,
I just bought a used HD2 without a charger. Seller told me the charger was not working and gave me only the USB cable. I am wondering if I can use my HD charger to charge the HD2. Of course, by swapping the cable.....
Anyone with a HD2 please post the part number/model number of their original HTC HD2 Charger so that I can check whether it is the same thing? Thanks all.....
Oh....Just downloaded a copy of the usual manual for HD2. It stated the original adaptor for HD2 is TC-P300 which is exactly the same as my HD's adaptor. So they are interchangable by swapping the USB cables!
its also the same as my brothers diamond charger
normally, you can use every usb charger.
if it doesnt work with your leo, it won't charge, but nothing should happen to your device.
DN41
Yup, it is exactly the same charger. (5 Volt 1Amp )
Same situation, changed from an HD to a HD2.
That's good! That mean any of those car cigarette lighter plug with USB output can be used with the appropriate USB cable to charge our HTC phone in the car? Don't need to buy the original car charger from HTC?
you can also charge your ipod with your hd2 chargers adapter.just connect the ipods' usb cable to the charger and plug in
applefruit said:
That's good! That mean any of those car cigarette lighter plug with USB output can be used with the appropriate USB cable to charge our HTC phone in the car? Don't need to buy the original car charger from HTC?
Click to expand...
Click to collapse
i would say about 99,9% does it. maybe there are 1 or 2 out there, which dont work. but normally, all of them should work.
DN41
Yup, but check Tbattery. I have this tool in NRG rom and it shows you how much current goes, or comes, from your battery.
From what I believe is that there are 2 states and 2 modes.
The mode is actually the source to where your HD2 is connected to. This is either a standard USB port on your laptop or the other one a charger.
If it is connected to the standard USB port it will draw a max of 500mA which is the max a USB should be able to deliver.
The charger can provide 1 Amp which is 1000mA, which means half the charge time till full.
You have to know that there are actually 4 conductors on the 'big' USB connector. Ground, 5 Volt and D+ and D- (the actual data).
The HD2 knows that it is connected to the charger when D+ and D- are connected to eachother. (no harm done btw)
Now some carchargers can deliver 1 Amp but they don't have the D's shorted and the HD2 only pulls 500mA from it since it doesn't see it as a 'HTC' charger.
The state is determined on the batt's %
If it is below 90% I believe it charges at full Amps (depending on the mode) above it goes in slow charge.
Looks like nowaday, we just need an adaptor with a USB output and various USB cables to charge different phones. Not too long ago, we need to carry one charger for each phone. haha....
Thanks for all those who replied!
I use a Nokia N97 car charger and it works very well. I'm guessing a normal N97 power adapter could work as well to charge your HD2.
info & caution.
Any USB port should be able to charge your HD2 & micro USB is the new standard charging specification, so it should become really common over time.
However, be careful what else you plug in! I bought a 3.2mm to micro USB adapter. It was fine on a standard Nokia charger (which delivered about 4.5 volts), but another one which put out about 7 volts, blew my poor HD2 up :-(
I got it repaired though. They replaced the main board = new IMEI etc, which would have been expensive out of warranty! Lucky me, but being without my HD2 was kinda hell!
I have checked the voltage out of that car charger. A friend of mine tested it before too on his HD2. N97 has a bigger voltage battery (1500 mA). He had problems finding a decent car charger for his HD2. He eventually bought 2 non-original chargers for an N97 and HD2. He took the connector from the non-original HD2 car charger, he cut off the connector for the N97 and he put the HD2 connector (he is an electrician, do not try this if you don't know what you are doing). He advised me to buy an original N97 charger that should work. I did buy one original car charger and I am satisfied with it. My HD2 is still in one piece without any service calls. I am saying that a N97 car charger should work just fine on an HD2.
Sam2k said:
Any USB port should be able to charge your HD2 & micro USB is the new standard charging specification, so it should become really common over time.
However, be careful what else you plug in! I bought a 3.2mm to micro USB adapter. It was fine on a standard Nokia charger (which delivered about 4.5 volts), but another one which put out about 7 volts, blew my poor HD2 up :-(
I got it repaired though. They replaced the main board = new IMEI etc, which would have been expensive out of warranty! Lucky me, but being without my HD2 was kinda hell!
Click to expand...
Click to collapse
This might have happened to me? It would not charge with my 500 ma USB supplies (computer nor the AC USB power adapter. Nor would it charge with my AC USB power adapter of 1 amp.
So I used my HTC HD2 car charger, plugged into my AC-12 volt car charger outlet, and it charged ok.
Two weeks later, nothing. So waiting for an external HTC HD2 battery charger from an eBay supplier. Tried different HTC HD2 batteries & HTC HD2 USB cables. No luck yet.
Related
I have a Qtek 9100 (Wizard clone) and I noticed that my battery is completely drained from my device. I can't find my AC adapter but I have my USB cable to my PC but that won't start recharing it. I recently saw a post that if your battery is completely dead, the USB cable connected to the phone cannot recharge it as it must atleast have 1000mW to charge it? I have tried to find some specs and I want to know exactly what kind of AC adapter I need for that phone? a 5v 2000mW mini USB adapter or something? Not sure what I need. Any ideas?
here is one that u can use
http://cgi.ebay.com/NEW-AUDIOVOX-AC...7092790QQihZ017QQcategoryZ11168QQcmdZViewItem
that is the one i have for my wizard
input: 100-240v/~0.2A 50-60Hz
output: 5V
Thanks Malik05,
I saw the specs on it and it does 5V-1A output. I was looking for a dealer in Canada and it seems that most cell phone stores only have AC adapters that ONLY do 0.2-0.5A which I tried and doesn't work. I couldn't find anyone selling a 5V-1A AC adapter.
raiden said:
Thanks Malik05,
I saw the specs on it and it does 5V-1A output. I was looking for a dealer in Canada and it seems that most cell phone stores only have AC adapters that ONLY do 0.2-0.5A which I tried and doesn't work. I couldn't find anyone selling a 5V-1A AC adapter.
Click to expand...
Click to collapse
http://cgi.ebay.com/NEW-OEM-TRAVEL-...ryZ15037QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
there ya go, it should do the trick, if not, then try going to a tmobile store...but that eBay link should do it...
Do you guys think there is anything special to the charger? When its fully drained, my iPod charger with a mini-USB cable doesn't work either (output is listed as 5V 1.0A).
the only thing special between the wizard charger is that it needs a full 1A, not .5A when the battery is at absolute zero...as for the iPod, i dont discuss apple products, it will turn into a debate hehe...
Thanks for the link to the new dealer Malik05 but he only ships within the US. ( Not Canada ). I saw one other place that might sell an adapter on ebay but the shipping was like $28 for an ac adapter. I am getting abit worried that even an Ipod charger that DOES supply 5V-1A doesn't even charger the phone when it's batteries are completely dead. It doesn't give me much confidence that any other adapter will work. Do you have another ebay link to purchase one that will work?
iPod dosnt have the same connectors as the wizard, what exactly are you talking about?
Sorry if I caused some confusion, I'll try to clarify some things.
I'm having the same problem charging my wizard since I lost my AC adapter over the weekend. I do, however, have the charger from my iPod (which is just an AC adapter with a female USB connector). With this iPod charger and a mini-USB data cable, I used to be able to charge the phone, that is until now. The only difference I can think of, is because the phone's battery is now fully drained.
The iPod charger is listed as 5v, 1.0A and still charges my iPod (using the iPod's dock connector cable).
o okay...i just thought that ipod chargers had their own standard, but anyway..you may need the original wizard charger...becacuse ive seen this problem with Motorola phones, some RAZR phones will not charge unless it is a motorla branded charger...
Hi,
Do you know if its possible to charge the i9000 using apple's car socket and a standard usb cable? I guess it should not make any difference, should it?
Thank you.
It shoud work, but very slowly. I have a car-USB adaptor and charged the phone with it, but it barely keeps the battery level. I bought a direct car charger and it charges very very fast (but the phone warms a lot). You'd better buy one, mine is a dealextreme one, very cheap.
Hi everybody, I am looking for a car charger for my HD2. I would like to ask if you think that a 1000mah one would damage the phone?
I have found some on eBay and I was considering buying it.
Please let me know what you think.
The standard mains power adaptor that comes with the phone is 1000mA so no it won't damage it.
Even a 5000mA won't, the phone will draw as much current as it needs.
Thanks for the reply, I was thinking of buying the charger and a car mount, so that I have my GPS needs for this years vacation, but I already had bad experience with a car charger that was not able to charge my wife's HTC Diamond when using GPS, that is why I want to buy a good one.
Try these: They work perfectly for me. The charger is a Motorola original charger.
http://forum.xda-developers.com/showthread.php?t=1130487
I use an original Nokia N97 car charger and I never had any problems. I suggest you do the same, they are a little more expensive than the other ones, but a car charger has to be able to give enough juice to the phone while running. A friend of mine uses a similar charger for his HD2, he even tried a charger with several normal USB ports and they can't supply enough power for the phone.
Thank you all for the replies. I have seen both chargers, and the Nokia N97 one is even cheaper on Amazon. I will probably go with the Motorola one, as it seems to have enough power for the HD2. I was able to find out that its maximum output is 950mah, which is not bad for a cell phone charger.
Looks also like a more durable one, and if the manufacturers won't change the port soon, might be able to get it to charge my future phones as well.
Now for a car mount, I will probably go with the Exomount, as I have read some very nice things about it, plus it is universal, so I'll be able to have it hold much more than this phone.
Hope this thread helps someone with the same questions as I had.
Micro usb is the agreed standard amongst most mobile phone manufacturers to reduce wastage in having to produce umpteen different power adaptors, plus it reduces manufacturing costs.
xaccers said:
Micro usb is the agreed standard amongst most mobile phone manufacturers to reduce wastage in having to produce umpteen different power adaptors, plus it reduces manufacturing costs.
Click to expand...
Click to collapse
amen to that , I was tiered of having so many different charges at home. At least at that time Nokia ruled the world (mobile world I mean), and most of them were Nokia chargers, hehe
But I prefer the micro usb norm. I just hope they will not invent a mini micro usb in the new devices. My xperia x1 and touch pro use a mini usb, which was the standard at that time
What is the max that the HD2 can get from the car charger?
I have a 500ma car charger, but when using the GPS it doesn't really charge, it seems that it only gives the same amount as the drain. (few days ago when I had 64% I connected the charger and drove for another hour or so, GPS always active, upon arrival battery was 63%)
will a 1000ma charger "charge" the battery during long drives?
I have a Brodit Active holder it works very well.
With GPS and Navigon on still charging.
I cannot put a link Serch for Brodit active holder HD2
mcbyte_it said:
What is the max that the HD2 can get from the car charger?
I have a 500ma car charger, but when using the GPS it doesn't really charge, it seems that it only gives the same amount as the drain. (few days ago when I had 64% I connected the charger and drove for another hour or so, GPS always active, upon arrival battery was 63%)
will a 1000ma charger "charge" the battery during long drives?
Click to expand...
Click to collapse
yes that will do the job,
if it does not, solder the 2 inner terminals together and that will make your phone think it plugged into the mains charger
i bought a cheap 1amp usb charger from deal extreme and did the above
Be careful with the soldering. If the charger can't supply 1A, it might damage the phone /car/charger.
Sent from my HD2 using XDA Premium App
I also need this for GPS in car,
Anyone recommend a good car charger? I have 2 cheap ones that don't charge
Sent from my Nexus One impersonator using xda premium
I bought this one for 8€ at a retailer. It is well manufactured and does what it should. http://www.hama.de/portal/articleId*179294/action*2563
Product number: hama 00093584
Charging current of 1000 mA for fast charging
12/24 V charger for practical charging in cars and trucks
space-saving coiled cable for avoiding cable clutter
Direct power supply and battery charging via the car cigarette lighter socket
IC controlled, intelligent charging (switch-over to trickle charge, overcharge protection)
LED function indicator
e approved
The dell streak that i have cannot charge while off, even when connected to a PC the charge doesn't seem to go up, but when on it can slowly charge.
Aside from that when off sometimes I get the cable with and exclamation mark symbol what is that supposed to mean? (my charger is a HTC USB charger)
You should ALWAYS use the original charger if possible. Otherwise the replacement needs to match the specifications of the original. Using an adapter with incorrect voltage can damage or completely fry the unit. An adapter with insufficient amperage but correct voltage will damage the adapter and could cause damage to a device.
AC charger should be capable of at least 1A.
In my experience the problem was in cable, not charger.
I use car charger 1A wich has nothing to do with Dell, it is ok with original cable.
any [email protected] charger that's within the usb voltage specs should work fine, if it strays too far because it's low quality you risk damaging it (this is true for ANY usb charger)
dell ships 2A @5.9v chargers too, so i would expect the streak to take at least up to that much though
The usb ports on your PC put out less than half the power the Streak needs to charge properly but as said above any 1A plus charger should work fine. I use one meant for an iPad @ 2.1A, one meant for a HP Touchpad at 2A and a generic 1A charger all work fine though the Streak grumps about the generic one it still charges fine.
I use capdase 4 slot usb charger and it works fine with my streak..
I got one of those really cheap ones from ebay and it charges fine!
Could someone recommend any good supplier of USB to microUSB cable that can handle 2 amps of charging the note 2? Other than the cable I got from Samsung, all my cable charge super slow my note 2 (from the original charger).
Thanks
Sent from my GT-N7100
interested in this one too! also, a 6ft cable if available.
TIA
I'd be interested, also!
I purchased one of those 6 foot cable extensions and just plugged the stock cable into it and the extension portion into the stock charger. Works like charm.
Sent from the best phone on the planet, Apple take Note............
My girlfriends Kindle usb cable took a dive so i went on search for replacement coming across -
http://www.amazon.com/Amazon-Kindle-Micro-Cable-Keyboard/dp/B006BGZJJ4/ref=cm_cr_pr_product_top
A buyer remarked he was using on his GS3 so I did some research on it.
Its 2.0 capable and built to carry charge are device requires giving me the feel of perfect replacement .
I ordered 2 of them will be receiving on Wednesday .
are you saying that the other micro usb cable wont work
ive got this nokia micro usb cable ca-101 and it works with the iluv triple usb charger which has got one port as fast port which is 2 amp one
any comments
boxer29 said:
are you saying that the other micro usb cable wont work
ive got this nokia micro usb cable ca-101 and it works with the iluv triple usb charger which has got one port as fast port which is 2 amp one
any comments
Click to expand...
Click to collapse
No no not saying they wont work....its the performance aspects of cables.
kindle cable contained in link is 5-6ft long , allows usb sync , built for 2amp current flow and user reviews are solid which = Good quality.
A little explanation on why I'm buying new cable,
My stock is defective micro connection wasn't sure easily falling out of device.
I took it to ATT service center showed them what was up and they ordered replacement cables that sucked.
1st Rcable was too short -Samsung was only 3ft long.
2nd Rcable didn't sync to pc - Off the wall brand 6 ft long.
From that point I broke out utility knife modified stock cable cutting some plastic off sleeve on micro end.
Connections now sure but cable looks beat up so replacement was needed.
Well I received my Amazon Kindle replacement cable today
Kindle Cable is of good quality , connections are firm much better then stock oem that came with device.
I highly recommend it.
hetzbh said:
Could someone recommend any good supplier of USB to microUSB cable that can handle 2 amps of charging the note 2? Other than the cable I got from Samsung, all my cable charge super slow my note 2 (from the original charger).
Click to expand...
Click to collapse
Yes, from my previous post:
I've struggled with a variety of the longer, non-OEM micro USB cables - the Amazon Basics, cables from Monoprice, etc. I had problems with all of them, either not providing enough current, or just flaking out within a short time. At one point I thought my phone (EVO 4G) had a problem with the micro USB jack (it didn't). Then one day I found a great cable on Amazon:
Search Amazon "Mediabridge - USB 2.0 A-Male to Micro-B Cable (6 Feet)"
I've been using this cable for several years now, and it has proven to be very durable (I've run over it with my office chair a number of times), and has always provided the full current of the charger I am using with no issues at all. I purchased another one recently to use in another location, and the quality is the same. I've been using these cables with all of my phones, and currently with the Note II.
I'm using this one from Monoprice, with the standard OEM Samsung wall / desk charger that came with the Note II:
http://www.monoprice.com/products/p...=10303&cs_id=1030307&p_id=5458&seq=1&format=2
It's six feet long, and is a pretty thick cable. I used it today for the first time to charge my new Note II. Coupled with the standard Samsung charger, it charged my Note II from 12 % to 100% in two hours, thirty one minutes -- and that included charging during two incoming phone calls that each lasted about 10 minutes.
Asquared said:
I'm using this one from Monoprice, with the standard OEM Samsung wall / desk charger that came with the Note II:
http://www.monoprice.com/products/p...=10303&cs_id=1030307&p_id=5458&seq=1&format=2
It's six feet long, and is a pretty thick cable. I used it today for the first time to charge my new Note II. Coupled with the standard Samsung charger, it charged my Note II from 12 % to 100% in two hours, thirty one minutes -- and that included charging during two incoming phone calls that each lasted about 10 minutes.
Click to expand...
Click to collapse
If my calculations are correct that's putting about 1120 Ma per hour into your phone.
I wonder if it would charge that fast on usb and have data too?
I also wonder how that compares to the stock USB cable that came with our charger.
JosephL said:
If my calculations are correct that's putting about 1120 Ma per hour into your phone.
I wonder if it would charge that fast on usb and have data too?
I also wonder how that compares to the stock USB cable that came with our charger.
Click to expand...
Click to collapse
Good questions. I was wondering the same things, particularly as the Monoprice cable is double the length of the stock one. At some point, I'll try both charging from my laptop with the Monoprice cable, and switching out and using the stock USB cable, for comparison purposes. My problem (well, not REALLY a problem at all!) is that my battery seems to be lasting around 27 hours, so it may be a while before I can get around to doing this!
Asquared said:
Good questions. I was wondering the same things, particularly as the Monoprice cable is double the length of the stock one. At some point, I'll try both charging from my laptop with the Monoprice cable, and switching out and using the stock USB cable, for comparison purposes. My problem (well, not REALLY a problem at all!) is that my battery seems to be lasting around 27 hours, so it may be a while before I can get around to doing this!
Click to expand...
Click to collapse
My stock usb cable that came with my Samsung charger shows charging on USB, even though it's plugged into the wall.
Conversely, put my note on my 2 amp car charger and the note says charging on AC.
Something is not right with the stock setup. Sure it charges but it should read charging on AC if it's on AC.
Just did a test. Found a usb cable from another device and plugged that into the Samsung stock charger. Now it reads "charging on AC."
I used that same cable and USB on my desktop. My note said charging on USB.
I think the cable was the bottle neck on the charger and the usb port on the desktop is not putting out enough power to make the Note believe its on AC.
USB is USB as far as our desktop/ Note goes, but if you are using AC, then the cable becomes more important if you want the fastest charge. What's apparent is we didn't get a real charging cable with our Note II. .
JosephL said:
Just did a test. Found a usb cable from another device and plugged that into the Samsung stock charger. Now it reads "charging on AC."
I used that same cable and USB on my desktop. My note said charging on USB.
I think the cable was the bottle neck on the charger and the usb port on the desktop is not putting out enough power to make the Note believe its on AC.
USB is USB as far as our desktop/ Note goes, but if you are using AC, then the cable becomes more important if you want the fastest charge. What's apparent is we didn't get a real charging cable with our Note II. .
Click to expand...
Click to collapse
So far, I haven't had any problems with my stock Samsung USB cable. You can always try the Monoprice cable I mentioned in a prior post. Also, I've read on these boards that it sometimes helps to try different USB ports on your computer, and that it can actually make a difference in charging.
Interesting topic I have been wondering about myself. The cable I got with my Note 2 is not good. The connector, when attached, is easy to move aside, does not hold in place and the sad thing is, it is original manufacturer cable.
I used several different cables and found out that the problem is the height (length) of the micro USB connector, which protrudes from the connector's plastic cover. The other thing I found is that standard Samsung cable, delivered with the phone is few fractions of millimeter shorter than any other cable I compared it to, and suffers from it.
Amazon basics cable I ordered recently might have the connector metal only barely longer, but holds much better (in fact it fits tightly and feels very well fixed in the socket). Contrary to some, I have not observed any problem when charging the phone with this cable and original charger. Maybe the newer cables are already adapted to the chargers as well.
The fact that the norm is not always the norm is also proved by original Samsung MHL adapter (with HDMI out). This has "micro USB" connector (here it is 11 pin though) which is roughly 1-2 mm longer than the one on supplied charger cable. This one gets "all way down" into the hole and still does not even touch the case with its plastic part (there might be ~ 1mm space between the plastic of connector and Note 2 case).
Now, when I look at potential micro USB cable for Note 2 I always check the length of micro USB metal part. It must be longer than original cable from Samsung, otherwise it will have flimsy connection.
Length
I try and use a shorter cable as the longer they get the more power you loose. I use a 6" inch usb A to B Micro. I love this cable because my phone can sit right next to my computer and its getting the max power.
i get them at cableforge.com
use this coupon it always works for me G5WJXH4F22MN
cheers.