Recently I have bought a used X1. One day, when the battery died, after charging it, a screen with 4 colour bars appeared (red, green, blue and white). There are also some signs on the screen:
KOVS110
SPL-0.72.01iNex
MicroP1-787
MicroP2-707.
On the bottom on the screen it says "Serial".
I cannot pass through this screen to get to use my phone as always. I tried to google this on the net but found some unrelated ROM-topics that didn't help me anyway, as I'm green as grass in these things.
Any ideas what to do? Thanks in advance for your help.
This might help. Disconnect the USB cable, remove the battery, then replace it and turn on the phone. As long as there is no problem, it should boot normally. But, the phone doesn't go into boot loader on it's own usually.
Well, that didn't help. Btw, what did you mean: "disconnect usb cable"? My phone wasn't in any way connected to a PC.
have you tried a hardreset?
Related
I've tried the Kaiser hardSPLv1 with vista and XP but all I get is my phone goes to a white screen on my phone and activesync goes grey, then I have to do a soft reset.
Could anyone help?
Try this. When activesync goes gray. Unhook the phone from the cable and rehook it.
still the same - conect my phone then start program get a message on phone I click 'continue' then phone screen goes white and sync after a minute goes grey tired unpluging the phone from usb and pluging back in and get nothing!
sigh.......
HardSPL will not install - WHITE SCREEN: SOLVED
Thank you! that worked and I have now updtes rom! Hopefully the phone will perform better now!!
Yesterday I took my battery out of my phone to remove the dust from inside the phone. When i replaced the battery back into the phone, it booted up into the tri-color screen and has been there ever since. I haven't modified the phone since receiving it from AT&T at all. When i actually noticed the problem I tried to reset the phone through the hole on the bottom of the phone. At first, it booted up normally but was out of batteries since it had been running on a bright screen for a couple of hours. Thus it turned off immediately. I have tried to reset it again but it seems to do nothing. Since then when I put the battery back in and I turn the phone on it returns to the tri-colored screen and it says SERIAL in the bottom white area. When plugged into my computer it says USB in the white area. On the top of the tri colored screen, in the red area, it says:
KAIS1*0
SPL-1.56.0000
CPLD-8
I thought about downloading the newest ROM update from HTC but my phone wont sync with my computer, and the tutorial says it needs to in order to install properly. If anyone could help, please let me know!
Update!
I put the battery back into the phone and it booted up just fine....it was a little slow and worked normally for a couple of minutes. Soon it started to act up. When i plugged the phone into my computer it automatically started to freeze, when i unplugged it from the computer it would work just fine! I then turned my phone off again and now it is back to the tri-color screen again!
try hard-resetting the phone.
To do this, hold down the two soft keys at the front while pushing the stylus into the reset hole. Just make sure to back up any data you want, as it will delete it all (files, contacts, etc.)
Tried a Hard Reset
When I finished it, it just went back to that tri-colored screen. Now the phone will turn on every 10th time i try and work for a couple of minutes. When the screen turns off it wont turn back on when i push the power button. The green light still blinks though.
I have been having this exact same problem for a little while now, any help would be more than appreciated.
EDIT: Everything about the phone was AT&T stock ROM from Oct. '07.
i think it replacement time
hi all once again.i was using my kaiser yesterday then my phone went into tri screen.tried hard reset soft reset.phone reboots in tri screen.im using Duttys Official WM6.1 Rom 5.2.19716 UC.
ihave kais130 mfg /spl 1-0.0lipof /cpld-8 on screen.
if there is a solution to this i would appreciate help in resolving.thanks in advance
Another sad update!
Well as of this second my phone works okay...slower than usual....but in an hour or so the screen will turn off and the phone will stop working, i will take the battery out.....wait about 45 minutes and hope that it boots up normally. No one has any idea why this is happening to multiple people? I have had this phone for maybe 3-4 months. Is the failure rate that broad and fast on these phones???
WTF
This phone is ridiculous. Now if I keep the phone plugged into my computer so the screen wont time off, the phone works just as normal. The moment I unplug the phone from charging it decides to die on me after an hour or so!
this happened to me last nite.
spent hours and hours trying to fix.
ended up reflashing orig att rom..
everything is fine..
proceeded on to a cooked rom and all is well..
added some apps ..
so far -- awesome
Good News!
Magically my phone started syncing with my computer randomly. Thus it allowed me to flash the rom with the original ATT rom and so far my phone is back to normal working great!
tri screen sorted
i bought my kaiser off ebay..i couldnt sort tri screen.i had various roms on at various times .i had no warranty. on pay as you go.decided to take to local o2 shop.got it back today fully working for free.took them 8 days.
Hey, did you have any luck fixing this problem - I've been looking mad for a solution to my tri-screen problem, but no joy...
KAISI*0
SPL-1.93.0000
CPLD-8
appears on my screen.... I don't now how to fix this puppy and it's only a couple of months old...
I started plugging the charger in and soft reset and it would work until i could find a new OS for it, Rom or RUU I think, I am not sure if it works, but now I can't get it off Tri-Screen to run it..
Any help anyone please?
You better take a look here for a solution : http://forum.xda-developers.com/showthread.php?t=423486
jezzaflyboy said:
Hey, did you have any luck fixing this problem - I've been looking mad for a solution to my tri-screen problem, but no joy...
KAISI*0
SPL-1.93.0000
CPLD-8
appears on my screen.... I don't now how to fix this puppy and it's only a couple of months old...
I started plugging the charger in and soft reset and it would work until i could find a new OS for it, Rom or RUU I think, I am not sure if it works, but now I can't get it off Tri-Screen to run it..
Any help anyone please?
Click to expand...
Click to collapse
Hi People
I think I have really bricked my Diamond for sure. I have read all the threads related to this problem and have tried all the possible fixes but to no avail.
Here is the problem: It is stuck on the first screen after tri colour screen showing the RGD info in red ink at the bottom right cornor. Pc wont recognize it and Active Sync 4.5 on xp is grey, not green.
I have done a few Hard resets and Soft resets. I have Olinex Hard Spl installed. Had Dutty's 1.6 working perfectly when decided to cook my own with Surface Kitchen. My first cooked rom worked fine and then I cooked another one with same base Stock rom , adding som programs and bam, this thing happened.
Please Help Help and yes I had flashed the same Diamond with every available cooked rom with no problem.
Thanks in advance. Lets not Die this beautiful Jewel.
Anyone please?
tararura said:
Anyone please?
Click to expand...
Click to collapse
Can you get it into bootloader mode??? If so, you should be fine to re-flash at that point.
I can get it to tri colour screen but it wont sync with pc ...?
tararura said:
I can get it to tri colour screen but it wont sync with pc ...?
Click to expand...
Click to collapse
So after getting to the tri-color screen and then plugging in the USB cable, you do not get "USB" at the bottom of the screen?????
Thanks for the quick reply..
Ok here is what I am doing. I perform the hard reset. Get the tri colour screen for couple of seconds and then it comes to the screen where it asks to press Volup to restore. I did it with the usb connected and usb disconnected but it wont sync. Active sync icon at the bottom on pc stays grey not green.
Pressing Volup on diamond restores, reboots and brings it back to 1st splash screen with RGD info at the bottom in red ink. aaaaah
When you are in bootscreen, connect via usb.
In the bottom off your screen you should see "usb"!
If this is what you see then flash one of the stock roms again.
After you've done this, your Diamond restarts and everything should be OK again!
Good luck!
Ok, do this:
1. Unplug the USB cable from the phone.
2. Hold down the Volume-down key and the Power button, then press (and let go of) the RESET button with your stylus.
3. When the tri-color screen appears, you can let go of the buttons.
4. The screen should say "Serial" at the bottom (in the gray color area).
5. Plug in the USB cable (The screen should change to "USB").
6. Run the RUU app to re-flash the phone.
That should get you back up and running.
To enter bootloader, turn phone off then press volume down and reset simultaneously and then power ono. If you have done this correctly it will remain there and the word "serial" appears at the bottom. Then plug in USB and the word changes to "USB" you can now flash ROM
When I flashed mine it also got stuck te first time because Windows found it necessary to install new USB driver when the Flash util wanted to connect to the HTC. The flash program jumped out leaving the diamond with the RGB screen...
But, after windows installed the new USB driver, I restarted the flash program and it finished just fine.
So if you cannot connect anymore I would try to find out if the USB driver has changed. Did you try connecting to another USB port?
Otherwise I would try to connect to another PC...
Hope it helps,
Beamer
fingers crossed
hope you unbricked it m8
@tararura
Be sure to come back and update the thread if you were successful. It may help others later if they search instead of starting another thread with a similar problem.
Holy smokes......
Its breathing again. Thank you TomInMB and Windoze9t8. Give yourselves a kiss for helping me out.
I used Windoze9t8's method and it came to the serial screen and then I flashed it with Dutty's.
So I was using hard reset method to get to bootloader screen, which was wrong.
So for everyone else, its Voldown and reset button at the same time for Bootloader screen.
Flashing is done and Active Sync recognized the Diamond.
Thanks again for everyone..... and I am sure that a few of us learnt the new trick from this thread.....
Glad to hear you're all set!!!! I sure would hate to have the feeling that my precious diamond was useless!!!!
Thats right , I already lost a lots of sleep trying to fix it last night..
Hello,
Today my Diamond probably died.. in fact it is MDA Compact IV.
I got new battery from ebay (original 1340mah from HTC). I put new battery to MDA but it didn't start. I tried to plug charger, but there is all time such situation:
- d-pad shine twice like during charging,
- one vibra ring
- splash screens
- turn off after about 10 seconds
I change battery with old one but there is the same problem.
I can make Hard Reset, I can enter bootloader mode, but nothing more.
Vibra, splash, reset again and again. If I pull off charger- phone is dead, there is no possibility to switch on.
Does anybody know such problem? Is there any solution? I read somewhere that is probably dead mainboard, is it true?
Please somebody help me, I got my MDA only one week
There was warranty but I installed HardSPL and unofficial ROM, so I can't turn it to service
Does the phone reset when you're in bootloader as well?
No, I can enter bootloader mode.
I have such words on screen:
DIAM200 MFG 64M
SPL-1.40.OliNex
MicroP-Diam (LED) v11
PSOC-Vict STAGE_PVT v0x20
USB.
It stays in bootloader. I can quit bootloader by soft reset. If I pull charger off then Diamond turns off.
you sure no liquid went in? or any falls?
if not - probably a faulty ROM or Radio... what you can try to do is first fully charge your phone (just keep it turned off and attached to charger).
once charged fully (you can tell by the d-pad light) when in bootloader, connect it to USB to your computer. it should change from Serial to USB on your phone. then flash a radio (preferably the one that came stock) via the Custom RUU method.
if that doesn't work... repeat steps above for a ROM...
and make sure u keep your fingers crossed good luck!
Ok, situation for today looks this way:
1. I can't turn the phone ON.
2. If I connect phone to charger or PC phone turns ON. There is one vibra ring and splash screen without numbers in corner (ROM, radio etc). Splash screen in ON for about 10-12 second, then phone is rebooting. It going all around continuously.
3. During displaying splash screen I CAN enter bootloader mode or make hard reset. If I enter to bootloader and plug charger off then phone turns OFF.
In bootloader mode there is such text on display:
DIAM200 MFG 64M
SPL- 1.40. OliNex
MicroP-Diam (LED) v11
pSOC-Vict STAGE_PVT v0x20
USB.
Windows in my PC makes sound as connected UBS equipment, but ActiveSync is not connected (grey).
4. After running bootloader mode I CAN run DiamondCustomRUU.exe. It looks like updates, ROM, Radios are installed- indicator is running in my PC and also on Diamond screen. After finishing installation there is again: reset, vibra, splash screen 10-12 second, reset, vibra... etc.
I tried to install many ROM, Radios and all SPL but final is always the same.
5. I tried to install original SPL- installation looks successful, but after reset in bootloader mode there is still: SPL- 1.40. OliNex. This point is most strange for me.
6. I can connect via mtty (but activesync is still gray), but I don't know commands for mtty and I don't know what more can I do through mtty.
For me right now most important is to turn SPL back- then I can return device to service.
Does anybody knows some solutions? I'm opened for any suggestions...
Thanks,
go and stay in boot loader mode (tri-stripe colored bands) and flash with custom ruu another rom, have you tried this simple step?
EDIT: sorry I read right now you tried, so bad, so unlucky!
Seems like the battery contacts on Ur device are faulty - The gold plating might have worn out and the contact with battery terminals is bad, so device registers critical battery and shuts off.
Try cleaning the contacts with a piece cotton or a soft cloth soaked in alcohol on all the contacts. (avoid too much - should not enter the device!!)
Could you try charging your battery without phone?
Hi, I'm new to XDA Dveloper. sorry if its already questioned..I don't have time to search for them, I'm running my laptop on battery that only will last about 15 minutes..and I have my electricity out..
Yesterday, I got My diamond exposed to water...it was raining hard and I was on my bike with my diamond in my pocket..
when I got home, my diamond begin to act strangely, it keeps lower its volume(to vibrate state) when I try to press the increase volume rocker, it goes back down to vibrate. but I manage to shut it down with slide2shutdown...and charge it (the battery only 7% left). this morning I get up and switch on the diamond, but It doesn't boot like usual(theTOUCHDiamond sceen)...
it only shows 4 bars (RED, GREEN, BLUE, and WHITE)consist of:
RED BAR with this:
DIAM100 64M
SPL-1.37.Olinex
MicroP-Diam (LED) v11
GREEN Bar with:
PSOC-Diam Stage_PVT v0x30
BLUE Bar : blank
WHITE Bar with
Serial (only "serial is written, nothing more)
That all, and when I try to connect with USB cable, it demands Qualcomm CDMA Drivers...(I use My friend's laptop....no activesync installed)
anyhelp would be appreciated.
thanks
Its strange..., Now my phone could boot normally, but the volume control still error..it keep decreasing( i tried to increase it but it keep getting back to 'vibrate' is this becaus the water?
EDIT: I'm sorry...its still the same, if I restart the device..it shows the 4 colored bars screen again. when I try to reset it, 1 of 10 attempts is likely that diamond boot normally..but the volume error is still there...can sum1 help me?
PS: Sorry, I don't know that I could edit my post..
bellsprout said:
Its strange..., Now my phone could boot normally, but the volume control still error..it keep decreasing( i tried to increase it but it keep getting back to 'vibrate' is this becaus the water?
EDIT: I'm sorry...its still the same, if I restart the device..it shows the 4 colored bars screen again. when I try to reset it, 1 of 10 attempts is likely that diamond boot normally..but the volume error is still there...can sum1 help me?
PS: Sorry, I don't know that I could edit my post..
Click to expand...
Click to collapse
what are you trying to hardreset device..??
A hard reset should only be performed if a normal reset does not solve a system
problem. After a hard reset, the device is restored to its default settingsā
the way it was when you first purchased it and turned it on. Any programs you installed, data you entered, and settings you customized on your device will be lost. Only Windows MobileĀ® software and other pre-installed programs will remain.
Try flashing back to stock rom?
Sent from my GT-P1000 using XDA App
Hi!
I have a boot problem also.
I used Memo ROM about 1 month ago. That was worked well still today. I restarted my Diamond today, it was not boot correctly. Only reboot the phone after showing the ROM information. I made hard reset and put back the rom again, but the phone is not boot properly.
Could to help somebody for me?
I solved the problem.
I downloaded the original rom (included with radio rom) from htc.com.
I put the phone to bootloader mode and flashed this original ROM.
After flashing finished, my diamond boot to WM6.1.
I don't know what was the problem, but it works again...
I hope never happening this again!