MY XPERIA SHOWS UP ONLY 200 mb of total memory is it oke ?
in a few words yes...
but if u need more explanations you should provide more info like foe example what rom are you using...
if I am not mistaken 512mb of internal memory is split to storage space and to ram... so 200mb sounds good to me...
Hello,
I have strange RAM problem on my X1, it shows 128MB both on WM Device information and mtty info 7. How can I change back to 256MB?
this is the output of mtty..
Cmd>info 7
HTC Integrated Re-Flash Utility, Common Base Version : 1.51d
Device Name: Kovsky, Bootloader Version : 0.78.OliNex
Built at: Feb 24 2009 15:27:55
Copyright (c) 1998-2007 High Tech Computer Corporation
Board ID=0x81
Project ID = 0x0
MicroP1 ID=0x787
MicroP2 ID=0x707
gCurrentPanel=0x4
CPU ID=0x4117B362
AMSS7200A
BAT ID=1, BAT over temperature=0
RAM Size : 128MB
Cmd>info 8
--- 2K bytes sector version ---
DEVICE NAME=micron_mt29f4g16abc
DEVICE ID=0xBC
DEVICE MAKER ID=0x2C
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x1000
BLOCK PAGE=0x40
Checking block information
BLOCK 4 (0x4) is reversed block
BLOCK 5 (0x5) is reversed block
BLOCK 7 (0x7) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 9 (0x9) is reversed block
BLOCK 16 (0x10) is reversed block
BLOCK 17 (0x11) is reversed block
BLOCK 18 (0x12) is reversed block
BLOCK 25 (0x19) is reversed block
BLOCK 26 (0x1A) is reversed block
BLOCK 27 (0x1B) is reversed block
BLOCK 28 (0x1C) is reversed block
BLOCK 29 (0x1D) is reversed block
BLOCK 30 (0x1E) is reversed block
BLOCK 31 (0x1F) is reversed block
BLOCK 32 (0x20) is reversed block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x8C0
Partition[2], type=0x25, start=0xF00, total=0x16E80
Partition[3], type=0x4, start=0x17D80, total=0x23540
CE Total Length(with sector info) = 0xBF7EC00
CE CheckSum Length(without sector info) = 0xBEC0000
Cmd>info 9
Storage Start Addr=0x5C2E0000, length:0x11BBAA00
Regards,
briansusilo
Related
My kaiser just booting to the bootloader screen and says Serial at the bottom.
KAIS130 MFG
SPL-1.0.OliPof
CPLD-8
When I plug in a USB cable it changes the 'Serial' to 'USB'. when I reboot the phone without the USB cable it's going straight into bootloader mode and I can see a quick "missing image file" message then the red/grn/blue screen.
Can someone help me please?
MTTY command info 8 shows:
Cmd>info 8
--- 2K bytes sector version ---
DEVICE NAME=samsung_k9k2g08
DEVICE ID=0xAA
DEVICE MAKER ID=0xEC
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 2 (0x2) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 9 (0x9) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 16 (0x10) is reversed block
BLOCK 17 (0x11) is reversed block
BLOCK 18 (0x12) is reversed block
BLOCK 19 (0x13) is reversed block
BLOCK 566 (0x236) is bad block
BLOCK 1228 (0x4CC) is bad block
BLOCK 1404 (0x57C) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x700
Partition[2], type=0x25, start=0xD40, total=0x7800
Partition[3], type=0x4, start=0x8540, total=0x12D80
CE Total Length(with sector info) = 0x42E2A00
CE CheckSum Length(without sector info) = 0x42A0000
GSLEON please help me.
It just sounds like you had a bad flash.
Have you tried re-flashing the ROM on your phone?
Yes. I can flash new rom but i've got the same problem with bootloader.
im experiencing the same problem
disable usb connections on activesync, use mtty, connect to usb, and type "info 8" without the "" and paste the output here, and wait for gsleon3
--- 2K bytes sector version ---
DEVICE NAME=hynix_hyh0ssj0mf3p
DEVICE ID=0xBA
DEVICE MAKER ID=0xAD
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 2 (0x2) is reversed block
BLOCK 3 (0x3) is reversed block
BLOCK 4 (0x4) is reversed block
BLOCK 5 (0x5) is reversed block
BLOCK 7 (0x7) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 9 (0x9) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 12 (0xC) is reversed block
BLOCK 13 (0xD) is reversed block
BLOCK 14 (0xE) is reversed block
BLOCK 15 (0xF) is reversed block
BLOCK 16 (0x10) is reversed block
BLOCK 17 (0x11) is reversed block
BLOCK 18 (0x12) is reversed block
BLOCK 19 (0x13) is reversed block
BLOCK 20 (0x14) is reversed block
BLOCK 193 (0xC1) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x700
Partition[2], type=0x25, start=0xD40, total=0x93C0
Partition[3], type=0x4, start=0xA100, total=0x111C0
CE Total Length(with sector info) = 0x50D0800
CE CheckSum Length(without sector info) = 0x5080000
Here is what I have.
Does anybody know how to fix that?
Thanks very much.
I am waiting online!!!
Cmd>info 8
--- 2K bytes sector version ---
DEVICE NAME=samsung_k9k2g08
DEVICE ID=0xAA
DEVICE MAKER ID=0xEC
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 2 (0x2) is reversed block
BLOCK 3 (0x3) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 12 (0xC) is reversed block
BLOCK 13 (0xD) is reversed block
BLOCK 14 (0xE) is reversed block
BLOCK 579 (0x243) is bad block
BLOCK 1212 (0x4BC) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x900
Partition[2], type=0x25, start=0xF40, total=0xB080
Partition[3], type=0x4, start=0xBFC0, total=0xF000
CE Total Length(with sector info) = 0x603FE00
CE CheckSum Length(without sector info) = 0x5FE0000
Here is the answer from our master Olipro!
ECC checking is fully integrated into the Diamond SPL, there is nothing you can (or need to) do.
Maybe THIS is useful for you...
But I wonder if there is a way to fix them. Thanks for your reply.
Would someone tell me some commands that will mark the bad blocks?
THanks very much.
Don't know how you got this. But did you try and format your NAND? Hard Reset and selecting Volume Down to format device + NAND Storage?
I've tried that but it didn't make any sense.
Thank you all the same!
Hello all, and thanks in advance to all that are helping in any way.
Quick Background, my diamond is a CDMA, with default provider as Telus.
My goal is to get full access to nv for writing as well as reading.
I have installed juicys rom HSPL 0.43 and sprint touch pro radio.
Although my device is working, i can not get the rtask c command to work;
""rtask a
Enter Radio Bootloader
POWER ON PMIC VREG_USB : SUCCESS!
Invalid cmd!...readCID
@CID: 00000000
Cmd>rtask c
Calibration
No card inserted
HTC_SMEM_CE_RADIO_DBG_FLAG:300
Enter Radio Image"
after running info 8 i get
"info 8
--- 2K bytes sector version ---
DEVICE NAME=samsung_k9k2g08
DEVICE ID=0xAA
DEVICE MAKER ID=0xEC
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 12 (0xC) is reversed block
BLOCK 13 (0xD) is reversed block
BLOCK 14 (0xE) is reversed block
BLOCK 19 (0x13) is reversed block
BLOCK 20 (0x14) is reversed block
BLOCK 21 (0x15) is reversed block
BLOCK 22 (0x16) is reversed block
BLOCK 23 (0x17) is reversed block
BLOCK 342 (0x156) is bad block
BLOCK 534 (0x216) is bad block
BLOCK 1146 (0x47A) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x840
Partition[2], type=0x25, start=0xE80, total=0xD5C0
Partition[3], type=0x4, start=0xE440, total=0x2D640
CE Total Length(with sector info) = 0x7292200
CE CheckSum Length(without sector info) = 0x7220000
Cmd>"
Any and all help would be greatly apriciated.
---
$10 via paypal or cash to maill to anyone who can hel me resolve this issue
no takers at all?
Update:
So i tried this exact same thing on an htc touch pro of mine, and i got the EXACT same Cmd>rtask c
Calibration
No card inserted
HTC_SMEM_CE_RADIO_DBG_FLAG:300
Enter Radio Image"
Both are running on telus....
any help is greatly apriciated.
bump NOTHING SEAMS TO WORK... Is this a telus block?
I'm hoping someone can help me out, I would like to salvage what is now TILT #2 (so I can start messing around in the kitchen) since I picked up a poor specimen for the use of it's system board so I could get rid of the BB Pearl my work handed me. That said I can flash a smaller rom to the system but anything over 80-85 megs throws a 226 error. So I followed the advice given by JockyW to check the memory and below is the output and I'm sure the source of my problems.
I would like to be able to mark the bad blocks so they are not used anymore or recover them if possible.
Cmd>rtask a
POWER OFF PMIC VREG_USB : SUCCESS!
C VREG_USB : SUCCESS!
ECHO ON MODE
rbchk
Checking please wait..
Fond bad block on [0xfd]
****** Total [1] bad blocks******
Cmd>info 8
--- 2K bytes sector version ---
DEVICE NAME=samsung_k9k2g08
DEVICE ID=0xAA
DEVICE MAKER ID=0xEC
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 0 (0x0) is reversed block
BLOCK 1 (0x1) is reversed block
BLOCK 8 (0x8) is reversed block
BLOCK 10 (0xA) is reversed block
BLOCK 11 (0xB) is reversed block
BLOCK 16 (0x10) is reversed block
BLOCK 17 (0x11) is reversed block
BLOCK 18 (0x12) is reversed block
BLOCK 19 (0x13) is reversed block
Partition[0], type=0x20, start=0x2, total=0x3E
Partition[1], type=0x23, start=0x40, total=0x580
Partition[2], type=0x25, start=0x5C0, total=0x10B40
Partition[3], type=0x4, start=0x11100, total=0x9980
CE Total Length(with sector info) = 0x8908800
CE CheckSum Length(without sector info) = 0x8880000
Cmd>
Hi, i've experiencing some troubles with my TytnII (no GSM network, then GSM is back but i can hear any sound or call, etc.) and after reflashing ROM and RADIO (several kinds and several times) i still have them.
So i want to clear Nand as deep as possible.
This is the info that i get from MTTY:
Cmd>checkimage
SPL CRC checksum = 0xDF9FA8A7
CE CRC checksum = bad=0x241
0x27BAC496
ExtROM CRC checksum = 0x0
Cmd>info 8
--- 2K bytes sector version ---
DEVICE NAME=hynix_hyh0ssj0mf3p
DEVICE ID=0xBA
DEVICE MAKER ID=0xAD
PAGE SIZE=0x800
TOTAL PAGE SIZE=0x840
BLOCK COUNT=0x800
BLOCK PAGE=0x40
Checking block information
BLOCK 2 (0x2) is reversed block
BLOCK 3 (0x3) is reversed block
BLOCK 4 (0x4) is reversed block
BLOCK 5 (0x5) is reversed block
BLOCK 7 (0x7) is reversed block
BLOCK 9 (0x9) is reversed block
BLOCK 12 (0xC) is reversed block
BLOCK 13 (0xD) is reversed block
BLOCK 14 (0xE) is reversed block
BLOCK 15 (0xF) is reversed block
BLOCK 20 (0x14) is reversed block
BLOCK 289 (0x121) is bad block
BLOCK 1414 (0x586) is bad block
Partition[0], type=0x20, start=0x2, total=0x63E
Partition[1], type=0x23, start=0x640, total=0x740
Partition[2], type=0x25, start=0xD80, total=0xB4C0
Partition[3], type=0x4, start=0xC240, total=0xF080
CE Total Length(with sector info) = 0x6181200
CE CheckSum Length(without sector info) = 0x6120000
If i make set 16 0 (or set 14 0), and then task 8 i get:
Cmd>set 14 0
HTCST IÚÈÒHTCE
Cmd>task 8
And kaiser reboots but nothing happens, it is not formatted.
Please help !