hello my galaxy s keeps cycling the mass storage device. when i turn my phone on and wait for the mass storage cycle to finish it just keeps going over and over so it wont let me do anything to the phone is there any fix to this i also can not get into download mode as my 3 button combo wont work thank you for any advice
Related
Ok, so I had my Captivate flashed back to stock and had it rooted. I decided to update from JF6 to JH7 through Kies Mini. After it finished updating, my phone was stuck at the Samsung Galaxy S screen and then it turned black, but the buttons still light up.
I already tried doing the 3 button recovery/download mode in every way possible, but my phone won't seem to go into recovery mode or download mode no matter what I do.
When I leave the usb cable plugged into the phone as I turn it on, my computer plays the notification sound where a device has been connected, but still black screen on the phone. Happens when the AT&T screen loads, wonder if that would help somehow
Please help!
Raeon said:
When I leave the usb cable plugged into the phone as I turn it on, my computer plays the notification sound where a device has been connected
Click to expand...
Click to collapse
If you had usb debugging enabled you can send a "adb reboot download" or "adb reboot recovery" command to reboot the phone. If not then you probably have to make one of those usb jig's with the 301k resistor.
But you should still be able to enter download mode if you pull the battery, press the vol up/down and put the battery back. My stock phone couldn't enter recovery but it could get into download mode, keep trying.
Hmmmm. Still doesn't work when I pull out the battery, plug in the usb cable, hold the volume + and - down, and put the battery back on. It just shows the battery charging.
i have something similiar just have battery showing and wheel spinning when connected to pc or AT&T logo flashing if powered on and can't get into download mode...How does one get back to reality at this point.
your phone does not have the button combinations required to enter either download or recovery mode. I guess what you should have done before doing anything to your phone was test the button combinations in case something screwed up. then you should have flashed stock with the odin package posted in the development forum with the 3 button fix. I had to do this for my friend's captivated after realizing the button fix was disabled, but I hadn't broken the booting of the phone then. but now to fix it, other than trying to use adb to reboot into download, I have no idea what to do.
Looks like you'll need to make a JIG. Here's one thread on it:
http://forum.xda-developers.com/showthread.php?t=841512
norcal einstein said:
Looks like you'll need to make a JIG. Here's one thread on it:
http://forum.xda-developers.com/showthread.php?t=841512
Click to expand...
Click to collapse
Made a jig with parts bought from Radio Shack.
the jig was a success to get the phone back to download mode
Help !!!!!!!!!!!!!!!!!!!!!!!!!!
hmy captivate died after flashing Axura using clockwork
now I can not boot up the phone, unplug the battery for 15 Min and put it back but still the same can not boot up the phone....
please help
You need to figure out a way to get into Download Mode, use ODIN, and flash back to JF6. Once you have JF6 running, you can flash whatever rom you want again.
If you search, you'll see a bunch of posts on the different methods to get to Download Mode.
Goodluck.
Yes, I know if I get download mode I can flash whatever rom, but the problem is that the phone completely dead nothing shown in the screen, I have tried the following
1- try the combination of Vol down + Power
2- try the combination of Vol up + Vol Down + Power
3- try Vol down and then connect USB
4- try Vol down + Vol Up and then connect USB
all these while opening ODIN
also I tried this on both windows 7, and windows XP.
do you have any other suggestions to do.
please help
Still have the problem, need heeeeeeeeeeeeeeeeeeelp please
How did it exactly die? It'd be useful for people who may know a solution. I've heard of JIG a few times.
you get the little home lights on the bottom of the phone to light up at least?
Also.. does the computer recognize the device?
If not and it's completely black screen and you don't even feel it vibrate while booting? Its toast.
But.. try doing the battery/sim card pull - hold down both volume buttons plug in the USB and jam in the batter and see if that works.
Or.. to the ATT warranty center you shall go.
I was flashing Axura rom using clockwork recovery, and after complete the installation and start reboot this back screen comes on, now not booting at all
Odin not recognize the phone, or even the computer does not detect any connected device,
I tried pull the battery, wait for 15 min then connect the USB, hold vol up, down and power keys then put the battery back while holding these three keys nothing happen, the screen still black and the computer not detect it.
I tired all ways but nothing works with me.
Now I think it is complete died, Even I tried the hair dryer trick but nothing works.
some posts talk about JIG
How this JIG works and how to do it?
up for heeeeeeeeeeeeeeeeeelp
hzeid said:
I was flashing Axura rom using clockwork recovery, and after complete the installation and start reboot this back screen comes on, now not booting at all
Odin not recognize the phone, or even the computer does not detect any connected device,
I tried pull the battery, wait for 15 min then connect the USB, hold vol up, down and power keys then put the battery back while holding these three keys nothing happen, the screen still black and the computer not detect it.
I tired all ways but nothing works with me.
Now I think it is complete died, Even I tried the hair dryer trick but nothing works.
some posts talk about JIG
How this JIG works and how to do it?
Click to expand...
Click to collapse
USB Jig will trigger the phone into Download mode.
******Soldering Required******
http://forum.xda-developers.com/showthread.php?t=819551
****Solderless version****
http://forum.xda-developers.com/showthread.php?t=841512
I followed JIG solution, connect resistants of 301K on pin 4,5 on mini usb head, nothing works still black screen, no at&t log nothing
help any new suggestion
try charging the phone for a few hours, if possible try a different battery.
also you may be in download mode with a black screen. i had a bad crash once from too much overclock or a corrupted kernel flash with the manhatten project 1.6ghz kernel. it corrupted the image files for bootup and download mode, my startup screen was garbage and had a black screen for download mode. but download mode still worked. start odin, it may still show device connected.
I did connect the JIG for 10 sec then disconnect it, then connect the phone to the computer while ODIN open, but nothing happen the computer still not detecting the phone, also the screen still black, it does not even any sign of responding except it get heated when connect it to charger.
guys as posted in other thread, will reward 75 US$ for who will help me getting my phone back to life
if you got the phone through at&t, you might as well just go exchange it for a new one. the people there won't be able to determine if you've voided your warranty if they can't boot your phone either.
sorry I did not got the phone from AT&T, I bought it from Ebay so I can not send it back to them
Hate to be that guy, but alas I am
I flashed my Captivate with the latest Twingerbread ROM. Everything was running nice and smooth until I decided to use a Galaxy S Mod tool from the market place to change my battery icon.
Long story short the phone is now stuck trying to boot. It will run the Twingerbread loading animation for a few seconds, flash a screen that says
Candidates:
Preparing external SD Card
and then continue with the loading animation.
Before this happened I had been able to force download mode using only the volume up/down buttons, that is no longer the case. I have tried using adb to access and force download but the phone isn't found whether powered off or in it's current "loading" state. ODIN is able to recognize it as a COM:7 device but fails to flash it.
I'm in a bit over my head here, anyone have any suggestions on how to fix this?
Try this:
Open Odin and plug the cable into your computer only not your phone
Remove your battery from your phone
Wait 30 seconds and put it back in, don't turn your phone on
Hold both volume buttons down and then plug the cable into your phone, it should go into download mode.
jhernand1102 said:
Try this:
Open Odin and plug the cable into your computer only not your phone
Remove your battery from your phone
Wait 30 seconds and put it back in, don't turn your phone on
Hold both volume buttons down and then plug the cable into your phone, it should go into download mode.
Click to expand...
Click to collapse
Thank you for the suggestion but I can't get that to work for me. I tried it multiple times but it simply loads the charging screen. I have heard the term jig thrown around a time or two in here but can't seem to find any more info on it. Would that be my next step?
Yes if that doesn't work then you will need to get a jig to force download mode. Look here....http://www.mobiletechvideos.com/blog/?page_id=100
Good Luck
Nice, I don't have to make it even. Thanks for helping the noob out, jhernand1102. Hopefully this cures my issue.
when i turn on phone, it every time start on download mod. i don't hold
any button and it always start on download mode. what can i do??
And other people want but cannot get into download mode.
Did you flash any other kernel or something like that?
Sent from my GT-I9000 using XDA Premium App
no i had problem witch micro usb port because when i plug cable phone don't display window where i can choic mass storage. I turned off phone and when i turn on it start on download mod. now that is every time when i turn on it.
Hello, today my phone was hard bricked by connecting to pc...I wanted to boot it up to download mode, but because my mistake i hold power down button and no power up button...then pc starts installing qualcomm_qdload driver or something...but it wasnt installed...i disconnect phone from pc and it wont turn on...its totally killed, it wont power on on charger, or something, only when i connect it to pc i see qdload driver...its that possible?
kiosk123 said:
Hello, today my phone was hard bricked by connecting to pc...I wanted to boot it up to download mode, but because my mistake i hold power down button and no power up button...then pc starts installing qualcomm_qdload driver or something...but it wasnt installed...i disconnect phone from pc and it wont turn on...its totally killed, it wont power on on charger, or something, only when i connect it to pc i see qdload driver...its that possible?
Click to expand...
Click to collapse
Try this hard reset https://forum.xda-developers.com/lg-l90/general/guide-unbrick-hard-bricked-l90-variants-t3173429