Database Develop

Serial V2.05 after an upgrade failure, can't reset, can't get out of the boot loader

HI,
because pluging in the usb cable into my laptop caused it to shut down I tried to perform an upgrade (BA_TMUK_14200_112_11300_Ship.exe) of my tmobile mda III over bluetooth.
The device was connected and after the first screen of the upgrade process the computer lost connection with the device and since then all I see on screen of my mda is Serial v2.05.
I got a powered usb hub and connected the device thorugh it to my computer, but windows doesn't recognise it anymore as a pda, but just as an unknown usb device.
I tried hard reset of the mda (camera+power+reset) and I tried to exit boot loader mode (rec+power+reset) but nothing happens.
Please help me, I am desperate.
Thnx

what the hell have u done?
upgrading via Bluetooth? have u read the wiki before upgrading? ofcourse upgrading via bluetooth will not work. ull definitely lost connection even suspending the device how much more if the device is in bootloader mode? how sad.... try it again and this time use maupgradeutnoid.exe..turn your device into bootloader mode, kill activesync..put ur device in the cradle wait till the pc recognizes the device..(something like your device is now ready for use) and then click maupgradeutnoid.exe..remember just wait till the pc recognizes your device, don't click the maupgradeutnoid.exe immediately after putting the device in the cradle cause that will not work..this time read the wiki page mate..

next option
With the MaUpgradeUt_noID.exe I get error 150:romupgrade utility error
and with the BaUpgradeUt.exe I get error 100:connection error
(I read the wiki now
What else can I do?
If I connect my blueangel directly to my laptop, the laptop shuts down, so I have to use a hub.
What else can I try?

ok...
what can u see on the screen of ur device once u put the device to cradle..(serial to usb?) ok. remember, once u put ur device in the cradle and if u want to use maupgradenoid.exe for the first time, u have to wait at least a minute before u activate or click the maupgardenoid.exe.. another option is to use mtty.exe.. just search mtty in this site and ull fine the procedure on how to use that utility..once done, u can start upgrade ur device to ur desired rom..or try update ur device to ur shipped rom using BAUpgradeUt.exe to avoid that error100.. unless u have already upgrade ur device to different roms before.

screen
when I connect it to the usb cable it says serial

ohh..
maybe there something wrong with ur device or the cable ur using. have u tried using the usb cradle instead? putting ur device in the crdle or connect it using usb cable (bootloader mode) the Serial should be changed to USB..otherwise t u get the connection error and u can't upgrade ur device for that..

flash interupted

was flashing and some one caused a communication error- . tried to recovery but was unsuccessful, now iall i see is run, green, blue, and white. is this what you called bricked. what can i do???

No, it is not bricked, with a bricked Wizard you can't either charge or power on it.
Just get another computer with ActiveSync installed (preferably a Notebook computer), and try RUU again.
And MAKE SURE you have already CID-unlock (NOTE: CID unlock is NOT SIM unlock) before flashing custom ROMs, otherwise follow the stickies to flash the Button's ROM and unlock it before proceed.

help
how can i try RUU????
i´ve also my 9100 with 3 colors , but when i connect to activesync they don´t recognize it.
how can i turn on again my 9100?
thx
hugo

hugomalheiro said:
how can i try RUU????
i´ve also my 9100 with 3 colors , but when i connect to activesync they don´t recognize it.
how can i turn on again my 9100?
thx
hugo
Click to expand...
Click to collapse
Activesync doesn't work in Bootloaders (multi color screen),but you can flash the phone in Bootloaders mode.While in Bootloaders (Multi color screen),hook your phone with pc via usb cable and watch small usb appear at the bottom of the Bootloaders mode,it confirms connectivity with pc and run the RUU in the Rom ,it'll start to flash. Let it complete and phone will reboot and start to work normal.

I´ve tried several times to run the RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1 but the application says that there isn´t no phone connected.
what i´m i doing wrong?
thx

[HELP]How do i put my phone in ActiveSync Mode while on Bootloader???[HELP]

I am wanting to updrage my rom for my HTC Touch HD and there are tick boxes saying that make sure u perfom these before you update:
Battery over 50%
ActiveSync
connect phone to computer using USB
Disable the standyby on PC
after i click click next and do the steps the process gets stucked on 0% buth on phone and computer and after few minutes it says error
So i am sure that i have done all those but not to sure if my phone was in Activesync mode or not.
When the phone is turned on and connected to the computer connects using Activesync fine but when i turn the phone off and go on Bootloader mode connection is lost (as soon as i turn the device off)
so can someone please help how to activesync on bootloader mode
UPDATE:
I did HSPL and then BlackstoneRUUWrapper and now its working (its not getting stuck on 0%) and actually % is increasing
Everyone Thanks in Advance. I will tell you all when its done.

If it says USB when you connect to the pc while in bootloader mode, you're good to go

ye it says USB at the bottom of the screen but the process always stays at 0% then after a while it gives Error

wich rom do you want to instal and have you instald hspl?

ABaruwal said:
ye it says USB at the bottom of the screen but the process always stays at 0% then after a while it gives Error
Click to expand...
Click to collapse
connect ur phone directly in boot loader rather than thru active sync..
Run the USPL 2..
and then start the rom flash.
jus tick all the req fields in the RUU.(be in the bootloader) cos it makes no difference..
this is all assuming u have win XP or Vista with the req drivers.
cheers
chetan

Have you followed all of the steps in the Dummies Guide to flashing? (See link in my signature.)
The fact that you are able to connect to Activesync is fine. There is no need to be in Activesync whilst flashing and while in bootlaoder mode.

Have you read through the tutorial thread? There is a troubleshooter faq there. I did my first flash using it yesterday with no problems at all

Please read and post future queries on flashing in this tutorial/guide thread

SOLVED! Bootloaders as far as it goes...Will not load any flash with SSPL or HSPL.

About a year-ish ago windows stopped working on my spv3600 m700 Trinity. I looked into reflashing the phone & put a copy of schaps 4.30 striaght onto the fone no problems.
I now want to upgrade the rom again & can get it into the bootloader screen ok. My problem is that this is as far as I can get. I've even tried the minisd trick but I see loading box very briefly flash up on the screen & thats it...still in bootloader mode with serial but nothing else happens.
The fone is not bricked & if I reset it will load windows. I've tried the original flash & bootloader. Soft (SSPL) & hard Bootloader technique but to no avail.
Has anyone got any other solutions? Many thanks in advance, its sending me crazy!!

Ok I sorted the first problem of using SDcard to flash .MBH files. It was down to the miniSD card format not being FAT32. I reformat the card as FAT32 & then bootloader progressed to installation stage.
...now I have a new problem... i'm stuck in bootloader mode SPL 1.07.0000 IPL 0.50 after I used SSPL from my mobile in windows mode to get the 1.07ds override bootloader. This allowed me to flash the Radio to the latest chinese version. I then used this program again to Flash to windows 6.5 & then half way through it rebooted to the bootloader tricolour screen.
The problem is that now that windows is gone I can only run the standard bootloader SPL 1.07.0000 with the phone. If I try & upgrade a cooked ROM it comes up with an error code on the mobile. If I try an official version it checks the ROM & then says "not allowed".
Is there a way I can change the bootloader through the card SD? I can't either get the bootloader to change from serial msg to usb...doesnt matter how many times I plug in the USB & i'm using XP. Is there a way to force it into USB?
I've tried putting "Des crash proof SPL" ,"Hard SPL", "Hard SPL 1.20" onto SDmini card as TRINIMG.NBH bootloader loads then comes up with 00068002 error i presume on screen
I've tried putting official upgrades "RUU Trinity DOPODA SIA WWE...Ship.EXE rom" & "RUU Trinity HTC WWE .........GPS.exe rom" onto SDmini card as TRINIMG.NBH, bootloader loads, . . .checking, then displays "not allow" & "00028002" on screen! Now i'm really stuck!
Any help would be greatly appreciated!

looks pretty much the same like my trinity right now...
help would be very appreciated

Solved.
Finally worked out why my phone would not change from serial to usb on the bootloader screen. Its all down to the power from usb lead...luckily I have a double usb lead which I use for an external hard drive. Two usbs plugged into my laptop provides twice the current...as soon as I used this lead tadaaa, the phone comes on & is recognised by windows xp even when its in bootloader mode. If you don't have a lead try using a different computer...just incase the usb output is crap!
From here I then ran the unbrick / exploit program which you have to run two/three times but then this will put the phone into a bootloader which allows you to flash the phone with any ROM.
Hope this info is of any help.

steve54321 said:
Finally worked out why my phone would not change from serial to usb on the bootloader screen. Its all down to the power from usb lead...luckily I have a double usb lead which I use for an external hard drive. Two usbs plugged into my laptop provides twice the current...as soon as I used this lead tadaaa, the phone comes on & is recognised by windows xp even when its in bootloader mode. If you don't have a lead try using a different computer...just incase the usb output is crap!
From here I then ran the unbrick / exploit program which you have to run two/three times but then this will put the phone into a bootloader which allows you to flash the phone with any ROM.
Hope this info is of any help.
Click to expand...
Click to collapse
Still on bootloader with error 0068002
can't ran anything.
Please help......
SOLVED:::::::: sorry

Trinity bricked , pls help ...
steve54321 said:
Finally worked out why my phone would not change from serial to usb on the bootloader screen. Its all down to the power from usb lead...luckily I have a double usb lead which I use for an external hard drive. Two usbs plugged into my laptop provides twice the current...as soon as I used this lead tadaaa, the phone comes on & is recognised by windows xp even when its in bootloader mode. If you don't have a lead try using a different computer...just incase the usb output is crap!
From here I then ran the unbrick / exploit program which you have to run two/three times but then this will put the phone into a bootloader which allows you to flash the phone with any ROM.
Hope this info is of any help.
Click to expand...
Click to collapse
Hi , there ,
I am finding myself into the same situation but I do not realy get you : how You managed to get out of the bootloader mode where it says :
TRIN100
IPL-0.50
TRIN100
SPL-1.07.0000
Can you , pls, be more specific , cause I am a newbe who bricked his Trinity a week ago :::

Blocked with error 0068002
Hello, after I install nAr.23016.FRA.IE8-CHOME on my sfr s300+, I'm blocked on the first page HTC, etc...When I put the S300+ under bootloader (photo and power button action), I plug the USB and I itry to flash;result is a reboot. I try with TRINIMG.NBH and result is error 0068002.
I need help to resolve this problem.Can u help me? Regards.
dan (excuse my bad english)

Sudden black out

everytime i try to upgrade my xda alpine which is connected to the computer thru usb craddle, it suddenly turn off n went to bootloader mode....what is the prob??? help pls pls...

now i think it goes into bootloader mode after autoconfig!!! when it ask for autoconfig, no matter i choose yes or no, it wil go into bootloader mode!! help!!!

ronan_chai said:
now i think it goes into bootloader mode after autoconfig!!! when it ask for autoconfig, no matter i choose yes or no, it wil go into bootloader mode!! help!!!
Click to expand...
Click to collapse
should have before you upgrade, remove the sim card first ...!!! ​ you try to upgrade with an official ROM for your device ​ for the ROM you can find it at -> http://www.shipped-roms.com/index.php?category=windows mobile&model = Alpine

No...i didnt have my sim card inside when i upgrade...and now it wil go into bootloader mode right after autoconfiguration...and it also go into bootloader mode halfway upgrading...and lost connection with the computer...so i cannot upgrade or flash it back to original rom...what sud i do??

ronan_chai said:
No...i didnt have my sim card inside when i upgrade...and now it wil go into bootloader mode right after autoconfiguration...and it also go into bootloader mode halfway upgrading...and lost connection with the computer...so i cannot upgrade or flash it back to original rom...what sud i do??
Click to expand...
Click to collapse
try to hard reset the device , this is her guide HTC Alpine hard reset
To perform a full reset
A full device reset clears memory, deletes all data, and restores the Pocket PC Phone to its default settings. Programs installed at the factory remain. All data that you have created and programs you have installed are erased.
Press and hold the Power button, and then use your stylus to press the “soft reset button” at the same time, as shown below. Be sure you have backed up all your data on an SD card or on a desktop PC before performing a full reset. after you hard reset the device, connect to a USB sync and you Flash Room again All you have to remember, allow usb connection .... and not disabled its usb connection Okey ​if you still have problems you can contact me​

Do i need to go into bootloader mode first before flashing?? Cause what i did was, connect it the comp, and while it is stil connected with windows mobile device centre and the phone is still in windows mobile desktop, then i run the MaUpgradeUt_noID.exe, and halfway upgrading, it just turn off n go back to bootloader mode...and then after that, it auto black out after each autoconfiguration.
And by Flash Rom, do you mean just run the MaUpgradeUt_noID.exe with all the files in it?? or there is something else i should do???
Sorry for my ignorance And ur guidance will be very much appreaciated!!!!

ronan_chai said:
Do i need to go into bootloader mode first before flashing?? Cause what i did was, connect it the comp, and while it is stil connected with windows mobile device centre and the phone is still in windows mobile desktop, then i run the MaUpgradeUt_noID.exe, and halfway upgrading, it just turn off n go back to bootloader mode...and then after that, it auto black out after each autoconfiguration.
And by Flash Rom, do you mean just run the MaUpgradeUt_noID.exe with all the files in it?? or there is something else i should do???
Sorry for my ignorance And ur guidance will be very much appreaciated!!!!
Click to expand...
Click to collapse
Windows mobile device centre?--Seems to be the Vista/Win7 driver problem. Search for it, using the Search button.
Flashing with Win7/32bit or Vista

muckelmaus said:
Windows mobile device centre?--Seems to be the Vista/Win7 driver problem. Search for it, using the Search button.
Flashing with Win7/32bit or Vista
Click to expand...
Click to collapse
EnterBL.exe should reboot the device into bootloader only, Activesync should disable then. You can access bootloader manually, it's more safe

Now i managed to get into bootloader mode and upgrade it.. but the upgrade hangs halfway, the progress stays at 0% and saying it's upgrading radio, but always failed. What's should i do pls?

ronan_chai said:
Now i managed to get into bootloader mode and upgrade it.. but the upgrade hangs halfway, the progress stays at 0% and saying it's upgrading radio, but always failed. What's should i do pls?
Click to expand...
Click to collapse
remove the battery from the device and wait until 10 minutes, then plug it in again and make sure your device go to the bootloader to reflash
next time before you perform the upgrade whether you've unlock device ??