Related
I did the search, but not finding anything...Thanks for the help
Not sure what you want... but you can go to Start...Setings....System and choose CLEAR STORAGE and that will give you a hard reset as far as whiping data.
austinsnyc said:
-Enter Bootloader mode: Hold Camera + Power buttons together and reset with stylus(thanks pof)
-HardReset: Hold Both soft keys in while pushing in Reset button :When prompted push Green Talk Button to clear data.
Click to expand...
Click to collapse
This is the information I found... bu t I HAVE NOT been able to get my Tilt to Hard Reset from pushing any combination of buttons...
But this does work...
grizzley said:
you can go to Start...Setings....System and choose CLEAR STORAGE and that will give you a hard reset as far as whiping data.
Click to expand...
Click to collapse
Ron
I know this already. I am looking for combination of bottons + reset. As press softkeys + reset for 8525...etc
grizzley said:
Not sure what you want... but you can go to Start...Setings....System and choose CLEAR STORAGE and that will give you a hard reset as far as whiping data.
Click to expand...
Click to collapse
Don't forget about your good friend, WIKI.
I hard reset a TILT that was locked up after installing Blackberry connect to SD card (known issue). Hold down the two soft keys, then use the stylus to press the reset button for a few seconds, then release while still holding in the soft reset buttons. The warning message comes on, and as said earlier, use the green send key to initiate the data wipe.
Jim_R said:
I hard reset a TILT that was locked up after installing Blackberry connect to SD card (known issue). Hold down the two soft keys, then use the stylus to press the reset button for a few seconds, then release while still holding in the soft reset buttons. The warning message comes on, and as said earlier, use the green send key to initiate the data wipe.
Click to expand...
Click to collapse
interestingly, it does not work on my TyTN II.
However, its working on the Trinity.
It worked on my Kaiser/Tytn ll. Thanks!!!
not for me :-(
Hi,
maybe me being stupid, but this procedure does not work for me. Problem is that I installed software for the iGo bluetooth keyboard (I know ...) and ever since the Kaiser is resetting itself every 30 seconds. So what I get is only the smart mobility message, a short vibrate and then back to start. Anyone any idea how to get out of that? May I just press the wrong softkeys?
many thanks in advance
eRay42
new situation: the keys I press are definitely the right ones, I can also get into bootloader mode. I flashed the original rom (RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship) back which finished successful but the situation is the same. When I hard reset I am told it has been done, being asked to press the green button and it reverts to the old problem immediately. I should say that I have not modded my device so far, it was in original state before I installed the above mentioned software. Could it be a coincidence and it is a hardware problem?
HELP!!!
I found hard-resetting my HTC TyTN "GB" somewhat unpredictable. Holding down both soft keys while depressing the reset buttone is the correct procedure. It's either related to the HTC_END.cab. Do you have this installed?
Cheers
Strange, can't perform a hard reset either, using the softkeys of my TyTn II. No matter how long I press and hold them, no message screen, no option to hard reset.
The only way is to use Clear Storage.
pietrucci said:
Strange, can't perform a hard reset either, using the softkeys of my TyTn II. No matter how long I press and hold them, no message screen, no option to hard reset.
The only way is to use Clear Storage.
Click to expand...
Click to collapse
haha, my two fat fingers...
I finally managed to hardreset, using two pencils to push (only!) the softkeys.
pietrucci said:
haha, my two fat fingers...
I finally managed to hardreset, using two pencils to push (only!) the softkeys.
Click to expand...
Click to collapse
Pencil trick worked for me tooooo
reset
thank you..my tilt went crazy and won't bot...just keep restarting and turning off.
I had to use the pen and hold down
damn it now i have to restore everything
No still not working. These button things doesnt work. BTW does using Clear Storage give same effect, anyone?
I also haven't been able to perform hard reset on my TyTN II with the Soft Keys.. it just keeps rebooting! Can anyone help me?
Cumpz
LoL.. nothing like keep trying..
Already got it..
i read on another forum that i need to press the camera button and the power button, they are both located on the same side and press the reset button..
i done that but keep getting a red green blue and white bars, the text say sspl-1.0.0lipof and at the bottom serial..
its the same as the first thing i had to do to load wm6.1..????
thanks
icum said:
i read on another forum that i need to press the camera button and the power button, they are both located on the same side and press the reset button..
i done that but keep getting a red green blue and white bars, the text say sspl-1.0.0lipof and at the bottom serial..
its the same as the first thing i had to do to load wm6.1..????
thanks
Click to expand...
Click to collapse
It's in the Kaiser Wiki, under 'Kaiser resets'.
this is what is says...
Hard Reset **NB** This cannot be performed while the device is connected/charging!**
* Press and hold both soft keys
* Using a stylus, press and hold the soft reset button at the bottom of the phone
* Keep all three buttons pressed until the keypad lights turn off and then flash
* Release the soft reset button while still pressing the soft keys
* Let go of the two soft keys once the message "This operation will delete all your personal data, to manufacturer default" appears on screen
* Finally, press the green call button to perform the hard reset, or press other key to cancel
1. what buttons are the soft keys..
2. i pressed the power and the camera buttons then the reset set pinhole button.. release the reset pinhole button after the keypads lights go off still nothing..
Hi everyone, I was trying a new software and when I tried to recover from a Sprite backup, the phone now hangs on the boot up screen (the one with the R, G and D version numbers).
¿Could someone please tell me how to force a hard reset on start up?. I'm starting to panic.
Turn off phone, press both softkeys and then press the powerbutton for exactly one second!
Not more! Then release it...
It tells me to press the "send" button. ¿Which one is it?.
For those who want to reset it while the system is running they'll have to do this:
Go to Start >More > Expert > Clear Storage.
Then you have to enter 1234 and reset
For those who want to reset it while the system is running they'll have to do this:
Go to Start >More > Expert > Clear Storage.
Then you have to enter 1234 and reset
Disregard my previous question, I've already found out.
¡¡Thank you very much Dumdidum!!. You saved my day.
To HARD RESET Turn off the phone, keep pressed the two soft keys on the front, then press power for 1-2 seconds and it will ask to press SENd key. Send key = the green key for making calls.
If you press something else the phone will reboot.
I already found out, but thank you anyway.
laseru said:
To HARD RESET Turn off the phone, keep pressed the two soft keys on the front, then press power for 1-2 seconds and it will ask to press SENd key. Send key = the green key for making calls.
If you press something else the phone will reboot.
Click to expand...
Click to collapse
added to wiki
bigflavor said:
added to wiki
Click to expand...
Click to collapse
Just to give proper credit, it was actually Dumdidum who first answered me on how to hard reset thru hardware.
Arcano said:
Just to give proper credit, it was actually Dumdidum who first answered me on how to hard reset thru hardware.
Click to expand...
Click to collapse
Yea, but he only gave you part of the story.
Quick advice
Thanks for the info . Just a comment, the trick is to just momentairly press the on/off switch as you hold down both of the soft buttons. You must continue to hold both of those down until you see a message on the screen. Keeping the power button pressed didn't do the trick for me.
I am a new comer for the WM6. My X03HT(S730) can't do the hard reset after I install a Chinese input for professional/classical version. Does it make my S730 fail to do the hard reset? My S730 now is no function with the keyboard after I get in OS. By the way, the tripod-color mode is work.
*OOPS* wrong device
Yo thanx lalvarado,
Your advice did the thing for me, super!
Arcano said:
Hi everyone, I was trying a new software and when I tried to recover from a Sprite backup, the phone now hangs on the boot up screen (the one with the R, G and D version numbers).
¿Could someone please tell me how to force a hard reset on start up?. I'm starting to panic.
Click to expand...
Click to collapse
want you to hardreset your wings?
you press and hold the camera button & power button then press the reset button under your phone beside the charger
it's the small hold and you must have a small rod to scrapers in the hole
then your phone start with bootloader
your screen with 3 colour Red-Green-White
you can up any rom with it
sorry because my Eng is not very good
hope it help u!
can somebody PLEASE TELL ME HOW TO HARD RESET THIS THING!??!? i read themanual .. and along with 40 billion forum posts...
VOLUME DOWN and CENTER BUTTON pressed then pressing the reset pin and still holding the volume down and center button DOES NOT WORK.... regardless whether the phone is OFF or on
help
I had the same problem when i tried it the first time!
Try to Soft reset the device and go to the RGB info screen (where you can see the Boot loader version ect.) then hold the center button and volume down and reset the device again. Then it should work!
btw make sure to press the buttons long enough, you need to press it for at least 10 seconds until it has loaded everything for the HR
Actually what needs to be, this is after trying for almost half hour - down volume, center key and Power (not reset). But has Xui said you need to hold it until you get the screen advising you are about to Hard Reset the device.
BTW Mods, can someone update the Diamond Wiki with this info, I da** near broke by buttons thinkink I was not pressing hard enough. When in actuality I should have press the power and not the SoftReset.
This is what I did:
My touch screen doesn't work.
So I have to hard reset the thing.
Hold the power button to turn off the phone completely
Then hold vol down, center key, power button, around 5-6 seconds,
then you see the boot screen.
Thanks guys, you are super and helpful for sure.
hi all, my first ever post in this forum. first of all many thanks for being here.
I was reading too many threads about the diamond. mainly about hard reset problems and new roms. my problem is that I couldn't perform hard reset. searched over the forum, tried what others did, just no result, what I am getting is only soft reset.
the method is:
use reset button while holding volume down & enter buttons , release the reset and keep holding others until the information window appears on the screen... somebody says power button also needed to be hold. somebody suggest holding the enter button very carrefully as it is very easy to activate direction buttons. somebody says rom is need to be updated as existing rom can be corrupted.
I tried all of above, I did update the rom several times and checked if hard reset is working, no result.
my tricolor screen says :
DIAM100 MGF 64M
SPL-1.24.Hard
MicroP-Diam (LED) v11
PSOC-Diam STAGE_PVT v0x32
I've 1.37.405.1 and radio rom 1.00.25.03 now, I know they are older versions but I tried 1.96. series too but did not throw in another hspl.
is it worth to try flashing with newer hard-spl such as 1.93 and compatible roms. any suggestion is very appreciated. I just wory about it coz read in many threads it is good to perform a hard reset after a new rom.
ps:assuming if it is cannot be changed, any software to perform hard reset? sow somewhere video of it, any help?
thanks for reading
Read this.
http://www.hardreset.eu/htc_touch_diamond_hard_reset_soft_reset_en.html
thanks for post but link doesn't work. I assume there is just explaination of normal hard reset method which I tried several times already.
Hi
cant open the above link to confirm if the same as what method i use, press and hold volume down and enter and the reset and release all upon tri colour
i must remove the SIM to get a hardreset.
with inseted SIM the procedure not works on my device (why ever? no idea!)
Just to further clarify:
If you have the CDMA version (like I), you must hold down power button + volume down + enter button at same time. Press the reset button with your third hand and continue holding the buttons until a screen prompts you for a reset. Volume up button will confirm the hard reset.
That's what I had to do and I would love to meet the engineer behind that crazy combination... I had to prop the stylus in a 3 ring binder while holding the three buttons so i could jab the back of the phone into the stylus while my other two hands were preoccupied with this stupid combo.
Arg. Hope this helps
/rant
ekksman said:
Hi
cant open the above link to confirm if the same as what method i use, press and hold volume down and enter and the reset and release all upon tri colour
Click to expand...
Click to collapse
this is not the hard reset. I got the tricolor screen by holding volume down + reset button. for hard reset there must be a window asking your approval if you are confirming hard reset, than pressing volume up is performing it.
while holding volume down + enter and resetting is resulting soft reset only. I tried many times as if I am mistakenly pressing other buttons but not... any help?
edit:with sim or without it didn't make any difference. however, I tried the last method whitesoxxx suggest but didn't hold the reset as I hold the others, will give result in a minute. by the way my device is from orange, is it CDMA (sorry if it sound soo stupid
result:nope, didn't make many difference, still soft reset. one more question: this reset confirmation window, how many second later it suppose to appear?
thanks
my last post might point you in right direction...
WhiteSoxxx said:
Just to further clarify:
If you have the CDMA version (like I), you must hold down power button + volume down + enter button at same time. Press the reset button with your third hand and continue holding the buttons until a screen prompts you for a reset. Volume up button will confirm the hard reset.
That's what I had to do and I would love to meet the engineer behind that crazy combination... I had to prop the stylus in a 3 ring binder while holding the three buttons so i could jab the back of the phone into the stylus while my other two hands were preoccupied with this stupid combo.
Arg. Hope this helps
/rant
Click to expand...
Click to collapse
It is an incredibly stupid combo! I had to search xda-developers to figure it out the first time because i just didn't believe the user manual!
For me, it works easiest with the diamond face down on the edge of a desk and supported against a heavy object (shelving unit) so that the Vol Down & Enter combo can be done one handed. I then have a hand free to press reset, which is easy with the back cover off!
beleive me i have no any complain about how difficult to reach ald hold all those buttons at same time, I am quite use to it
I sent back the diamond today as hard reset problem was really annoying. I tought mine was defected somehow. will buy another, if next one does the same should I send it back again? is it really necessary to do hard reset after updating rom?
thanks
To perform a hard reset
1. Pull out the stylus.
2. With the device turned on, press and hold the VOLUME DOWN and
ENTER button, then press the RESET button with the stylus tip.
3. Release the RESET button, but continue pressing the VOLUME DOWN and ENTER buttons until you see a message on the screen.4. Release the VOLUME DOWN and ENTER buttons, then press the
VOLUME UP button to perform the hard reset, or press any other
button to cancel the reset.
4. Release the VOLUME DOWN and ENTER buttons, then press the
VOLUME UP button to perform the hard reset, or press any other
button to cancel the reset.
***Check this out! http://www.hardreset.eu/htc_touch_diamond_hard_reset_soft_reset_en.html
***I tried it,but the problem with YouTube didn't stop.
Very easy way to Hard reset the phone is by going to phone settings and select "Clear Storage" and enter 1234 click ok. (This is erase all the data and installed programs and will get the factory settings)
Hello everyone.
I am new to the whole custom rom and flashing thing, but after some reading and researching I decided to backup my stock rom and flash a custom one.
So I did successfully, to the point when the flash is done and I should do a so called Hard Reset. I've done the hard reset thing before and it worked, but now when I hold the both "silver" couloured buttons and the powerbutton at once the phone vibrates once and start booting.
I just don't know how to proceed with this since my X1 won't go in to Hard reset mode, I have no idea why or what I should do, so please, anyone just give me a hint and make my day.
Sorry if this is a totally useless thread for everyone else and it's just being annoying, but I really need some help here guys and girls.
Thanks in advance / Anton.
You probably just haven't gone through this procedure:
http://forum.xda-developers.com/showthread.php?t=431218
Hope that solves it
Good luck!
Actually I did, I followed BioVolt's videoguides on every step and when I checked afterwards on the tri color bootloader-screen it said: "KOVS110 SPL-0.72.01iNex" wich indicates that the Hard SPL procedure was successful.
Thanks for the hint tough, problem still not solved...
blondyz said:
Actually I did, I followed BioVolt's videoguides on every step and when I checked afterwards on the tri color bootloader-screen it said: "KOVS110 SPL-0.72.01iNex" wich indicates that the Hard SPL procedure was successful.
Thanks for the hint tough, problem still not solved...
Click to expand...
Click to collapse
I had the same problem - what you need to do is NOT hold the power button for long, just for like a second then it should work.
I too faced hardreset problem earlier, then later i found the following procedure holds corrects, atleast for my mobile. What i do is, press both silver buttons at a time and press power button only once and leave it(just press and leave only power button not the silver colored ones)..after few secs it will go to hard reset mode...
Try holding down the volume down button and the power button to go into the bootloader mode. From there, continue with your normal hard reset procedure which is holding down the 2 silver buttons and then press the reset button.
You only need to hold the two soft keys (silver buttons) to get into hard reset mode. if your phone is off, then you only need to tap the power button to turn on the phone, not hold it, but continue to hold the silver keys until you get the grey screen.
Hope that helps
blondyz said:
.....
So I did successfully, to the point when the flash is done and I should do a so called Hard Reset. I've done the hard reset thing before and it worked, but now when I hold the both "silver" couloured buttons and the powerbutton at once the phone vibrates once and start booting.
I just don't know how to proceed with this since my X1 won't go in to Hard reset mode, I have no idea why or what I should do, so please, anyone just give me a hint and make my day.
................
Click to expand...
Click to collapse
You need to completely shutdown your X1 first before hardreset. I mean COMPLETELY: remove your battery for at least 5s, then attach it and hard rest your device.
Thanks alot guys, actually the problem got solved by now, I treid a method I hadn't heard of before where you hold your two softkeys and under the battery cover give the "stylus hole" a push..
Worked just fine! Thanks alot to everyone bothering to help me, it's thanks to you guys I now have a working X1
Kinds regards / Anton.
the reason why its hard for people to hard reset from when its off is because they're holding the power button as well as the two silver keys!
you just hold the two silver keys and press the power key once, quickly.
keep holding the two silver keys until press R comes up!